2010-2019 Nissan Juke SUV Heater and air conditioner, and audio system -> Audio system User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Heater and air conditioner, and audio system -> Audio system for Your Nissan Juke SUV First Generation (2010-2019)

AUDIO SYSTEM (if equipped)  
layer. However, it may contribute in a small part to  
global warming.  
.
The following CDs may not work properly.  
— Copy control compact discs (CCCD)  
— Recordable compact discs (CD-R)  
— Rewritable compact discs (CD-RW)  
AUDIO OPERATION PRECAUTIONS  
WARNING:  
Special charging equipment and lubricant are required  
when servicing your vehicle’s air conditioner. Using  
improper refrigerants or lubricants will cause severe  
damage to the air conditioner system. (See “Air  
conditioner system refrigerant and lubricant” (P.9-6).)  
Do not adjust the audio system while driving so  
that full attention may be given to vehicle  
operation.  
The audio system operates when the ignition switch is  
in the “ACC” or “ON” position. If you want to listen to  
the radio or CD while the engine is not running, turn  
the ignition switch to the “ACC” position. Do not use  
for an extended period of time with the engine  
stopped.  
A
NISSAN dealer will be able to service your  
environmentally friendly air conditioner system.  
Air conditioner filter  
The air conditioner system is equipped with an air  
conditioner filter which collects dirt, dust, etc. To make  
sure the air conditioner heats defogs, and ventilates  
efficiently, replace the filter in accordance with the  
specified maintenance intervals listed in the separate  
maintenance booklet. To replace the filter, contact a  
NISSAN dealer.  
Radio  
.
Radio reception is affected by station signal  
strength, distance from radio transmitter, build-  
ings, bridges, mountains and other external  
influences. Intermittent changes in reception  
quality normally are caused by these external  
influences.  
The filter should be replaced if the air flow decreases  
significantly or if windows fog up easily when operating  
the heater or air conditioner.  
.
Using a cellular phone in or near the vehicle may  
influence radio reception quality.  
Compact Disc (CD) player  
.
During cold weather or rainy days, the player may  
malfunction due to the humidity. If this occurs,  
remove the CD from CD player and dehumidify or  
ventilate the player completely.  
SAA0480  
.
Do not use the following CDs as they may cause  
the CD player to malfunction.  
.
.
The player may skip while driving on rough roads.  
The CD player sometimes may not function when  
the passenger compartment temperature is ex-  
tremely high. Lower the temperature before use.  
— 8 cm (3.1 in) discs  
— CDs that are not round  
— CDs with a paper label  
.
.
Do not expose the CD to direct sunlight.  
CDs that are of poor quality, or are dirty,  
scratched, covered with fingerprints, or that have  
pin holes may not work properly.  
— CDs that are warped, scratched or have  
unusual edges.  
Heater and air conditioner, and audio system 4-15  
— CD lens cleaner discs  
correct direction before inserting the de-  
vice.).  
.
An iPod nano (1st Generation) may remain in fast  
forward or rewind mode if it is connected during a  
seek operation. In this case, please manually reset  
the iPod.  
.
.
This audio system can only play prerecorded CDs.  
It has no capabilities to record or burn CDs.  
.
.
Do not grab the USB port cover (if equipped)  
when pulling the USB device out of the port.  
This could damage the port and the cover.  
If the CD cannot be played, one of the following  
messages will be displayed.  
.
.
An iPod nano (2nd Generation) will continue to  
fast-forward or rewind if it is disconnected during  
a seek operation.  
Do not leave the USB cable in a place where  
it can be pulled unintentionally. Pulling the  
cable may damage the port.  
Error CD:  
.
Confirm that the CD is inserted correctly (the label  
side is facing up, etc.).  
An incorrect song title may appear when the Play  
Mode is changed while using an iPod nano (2nd  
Generation)  
.
Confirm that the CD is not bent or warped and it is  
free of scratches.  
The vehicle is not equipped with a USB device. USB  
devices should be purchased separately as necessary.  
.
.
Audiobooks may not play in the same order as  
they appear on an iPod.  
.
.
Confirm that the disc is a CD and not a DVD.  
Confirm that the disc contains audio files.  
This system cannot be used to format USB devices. To  
format a USB device, use a personal computer.  
Large video files cause slow responses in an iPod.  
The vehicle center display may momentarily black  
out, but will soon recover.  
In some states/area, the USB device for the front seats  
plays only sound without images for regulatory  
reasons, even when the vehicle is parked.  
Eject CD:  
This is a malfunction due to the temperature inside the  
player is too high. Remove the CD by pushing the  
EJECT button, and after a short time reinsert the CD.  
The CD can be played when the temperature of the  
player returns to normal.  
.
If an iPod automatically selects large video files  
while in the shuffle mode, the vehicle center  
display may momentarily black out, but will soon  
recover.  
This system supports various USB memory devices,  
USB hard drives and iPod players. Some USB devices  
may not be supported by this system.  
Bluetooth® Audio player  
.
Partitioned USB devices may not be played  
correctly.  
USB (Universal Serial Bus) Connection Port  
.
Some Bluetooth® audio devices may not be used  
with this system. For detailed information about  
Bluetooth® audio devices that are available for use  
with this system, contact a NISSAN dealer.  
.
Some characters used in other languages (Chi-  
nese, Japanese, etc.) are not displayed properly  
on display. Using English language characters  
with a USB device is recommended.  
WARNING:  
Do not connect, disconnect or operate the USB  
device while driving. Doing so can be a distrac-  
tion. If distracted you could lose control of your  
vehicle and cause an accident or serious injury.  
.
.
Before using a Bluetooth® audio system, the initial  
registration process for the audio device is  
necessary.  
Operation of the Bluetooth® audio system may  
vary depending on the audio device that is  
connected. Confirm the operation procedure  
before use.  
General notes for USB use:  
Refer to your device manufacturer’s owner information  
regarding the proper use and care of the device.  
CAUTION:  
Notes for iPod use:  
.
Do not force the USB device into the USB  
port. Inserting the USB device tilted or up-  
side-down into the port may damage the  
port. Make sure that the USB device is  
connected correctly into the USB port (Some  
iPod is a trademark of Apple Inc., registered in the U.S.  
and other countries.  
.
The playback of Bluetooth® audio will be paused  
under the following conditions. The playback will  
be resumed after the following conditions are  
completed.  
.
Improperly plugging in the iPod may cause a  
checkmark to be displayed on and off (flickering).  
Always make sure that the iPod is connected  
properly.  
USB devices come with a  
mark as a  
guide. Make sure that the mark is facing the  
4-16 Heater and air conditioner, and audio system  
— while using a hands-free phone  
greater file compression than the MP3 codec,  
enabling storage of more digital audio tracks in the  
same amount of space when compared to MP3s  
at the same level of quality.  
Playback order:  
— while checking a connection with a cell phone  
.
The in-vehicle antenna for Bluetooth® commu-  
nication is built in the system. Do not place the  
Bluetooth® audio device in an area surrounded by  
metal, far away from the system or in a narrow  
space where the device closely contacts the body  
or the seat. Otherwise, sound degradation or  
connection interference may occur.  
.
.
AAC (if equipped) — Advanced Audio Coding  
(AAC) is a compressed audio format. AAC offers  
greater file compression than MP3 and enables  
music file creation and storage at the same quality  
as MP3.  
Bit rate — Bit rate denotes the number of bits per  
second used by a digital music files. The size and  
.
.
While a Bluetooth® audio device is connected  
through the Bluetooth® wireless connection, the  
battery power of the device may discharge quicker  
than usual.  
This system is compatible with the Bluetooth® AV  
profile (A2DP and AVRCP).  
quality of  
a
compressed digital audio file is  
determined by the bit rate used when encoding  
the file.  
.
.
Sampling frequency — The rate at which the  
samples of a signal are converted from analog to  
digital (A/D conversion) per second.  
Bluetooth® is a trademark  
owned by Bluetooth SIG, Inc.  
and licensed to Visteon Cor-  
poration and Bosch.  
Multisession — Multisession is one of the methods  
for writing data to media. Writing data once to the  
media is called a single session, and writing more  
than once is called a multisession.  
Compact Disc (CD)/USB device with MP3/  
WMA/AAC  
.
ID3/WMA Tag — The ID3/WMA tag is the part of  
the encoded MP3 or WMA file that contains  
information about the digital music file such as  
song title, artist, album title, encoding bit rate,  
track time duration, etc. ID3 tag information is  
displayed on the Album/Artist/Song title line on  
the display.  
Terms:  
.
MP3 — MP3 is short for Moving Pictures Experts  
Group Audio Layer 3. MP3 is the most well known  
compressed digital audio file format. This format  
allows for near “CD quality” sound, but at a  
fraction of the size of normal audio files. MP3  
conversion of an audio track from CD can reduce  
the file size by approximately 10:1 ratio (Sampling:  
44.1 kHz, Bit rate: 128 kbps) with virtually no  
perceptible loss in quality. MP3 compression  
removes the redundant and irrelevant parts of a  
sound signal that the human ear doesn’t hear.  
SAA2494  
Music playback order of the CD with MP3 or WMA is  
as illustrated above.  
* Windows® and Windows Media® are registered  
trademarks and/or trademarks of Microsoft Corpora-  
tion in the United States of America and/or other  
countries.  
.
.
.
The names of folders not containing MP3/WMA  
files are not shown in the display.  
If there is a file in the top level of the disc, “Root” is  
displayed.  
The playback order is the order in which the files  
were written by the writing software, so the files  
might not be played in the desired order.  
.
WMA — Windows Media Audio (WMA) is a  
compressed audio format created by Microsoft as  
an alternative to MP3. The WMA codec offers  
Heater and air conditioner, and audio system 4-17  
Specification chart (for Type A audio):  
Supported media  
CD, CD-R, CD-RW, USB2.0  
ISO9660 LEVEL1, ISO9660 LEVEL2, Romeo, Joliet  
ISO9660 Level 3 (packet writing) is not supported.  
Files saved using the Live File System component (on a Windows Vista-based computer)  
are not supported.  
Supported file systems  
USB memory: FAT16, FAT32  
MPEG1, MPEG2, MPEG2.5  
Version  
32kHz - 44.1 kHz - 48kHz (model with Bluetooth® function)  
MP3  
Sampling frequency  
8 kHz - 48 kHz (model without Bluetooth® function)  
Bit rate  
32 kbps - 320 kbps VBR*4  
WMA7, WMA8, WMA9  
32 kHz - 48 kHz  
Version  
Supported versions*1  
WMA*2  
AAC  
Sampling frequency  
Bit rate  
48 kbps - 320 kbps, VBR*4  
MPEG-4 AAC  
Version  
Sampling frequency  
Bit rate  
8 kHz - 48 kHz  
32 kbps - 192 kbps, VBR*4  
ID tag VER1.0, VER1.1, VER2.2, VER2.3 (MP3 only) (model with Bluetooth® function)  
ID3 tag VER1.0, VER1.1, VER2.2, VER2.3, VER2.4 (MP3 only) (model without Bluetooth®  
function)  
Tag information (Song title and Artist name)  
WMA tag (WMA only)  
Folder levels: 8, Folders: 255 (including route folder), Files: 512 (Max. 255 files for one  
folder)  
CD, CD-R, CD-RW  
USB  
Folder levels  
Folder levels: 8, Folders 255, Files: 2500 (Max. 255 files for one folder)  
Memory size: 4GB  
01: ASCII, 02: ISO-8859-1, 03: UNICODE (UTF-16 BOM Big Endian), 04: UNICODE  
(UTF-16 Non-BOM Big Endian), 05: UNICODE (UTF-8), 06: UNICODE (Non-UTF-16  
BOM Little Endian), 07:SHIFT-JIS  
Displayable character codes*3  
*1  
*2  
*3  
*4  
Files created with a combination of 48 kHz sampling frequency and 64 kbps bit rate cannot be played.  
Protected WMA files (DRM) cannot be played.  
Available codes depend on what kind of media, versions and information are going to be displayed.  
When VBR files are played, the playback time may not be displayed correctly. WMA7 and WMA8 are not applied to VBR.  
4-18 Heater and air conditioner, and audio system  
Specification chart (for Type B audio):  
Supported media  
CD, CD-R, CD-RW, USB2.0  
CD, CD-R, CD-RW: ISO9660 LEVEL1, ISO9660 LEVEL2, Romeo, Joliet  
* ISO9660 Level 3 (packet writing) is not supported.  
* Files saved using the Live File System component (on a Windows Vista-based computer) are  
not supported.  
Supported file systems  
USB memory: FAT16, FAT32  
Version  
MPEG1 Audio Layer 3  
MP3  
Supported versions*1  
WMA*2  
Sampling frequency  
Bit rate  
32 kHz - 48 kHz  
32 kbps - 320 kbps, VBR*4  
Version  
WMA7, WMA8, WMA9  
Sampling frequency  
Bit rate  
32 kHz - 48 kHz  
32 kbps - 192 kbps, VBR4, 32 kbps - 320 kbps (WMA9 only)  
ID3 tag VER1.0, VER1.1, VER2.2, VER2.3, VER2.4 (MP3 only)  
WMA tag (WMA only)  
Tag information (Song title and Artist name)  
CD, CD-R, CD-RW  
USB  
Folder levels: 8, Folders: 255, Files: 999 (Max. 255 files for one folder)  
Folder levels  
Folder levels: 8, Folders 255, Files: 2500 (Max. 255 files for one folder)  
Memory size: 4GB  
01: ASCII, 02: ISO-8859-1, 03: UNICODE (UTF-16 BOM Big Endian), 04: UNICODE (UTF-16  
Non-BOM Big Endian), 05: UNICODE (UTF-8)  
Displayable character codes*3  
*1  
*2  
*3  
*4  
Files created with a combination of 48 kHz sampling frequency and 64 kbps bit rate cannot be played.  
Protected WMA files (DRM) cannot be played.  
Available codes depend on what kind of media, versions and information are going to be displayed.  
When VBR files are played, the playback time may not be displayed correctly.  
Heater and air conditioner, and audio system 4-19  
Specification chart (for Type C audio):  
Supported media  
Supported file systems  
Version  
CD, CD-R, CD-RW, USB2.0  
ISO9660 LEVEL 1, ISO9660 LEVEL2, Apple ISO, Romeo, Joliet  
*ISO9660 LEVEL 3 (packet writing) is not supported.  
MPEG1, MPEG2, MPEG2.5  
MP3  
Sampling frequency  
Bit rate  
8 kHz - 48 kHz  
8 kbps - 320 kbps, VBR  
Supported  
versions*1  
Version  
WMA7, WMA8, WMA9  
WMA*2 Sampling frequency  
Bit rate  
32 kHz - 48 kHz  
48 kbps - 192 kbps, VBR  
Tag information  
Folder levels  
ID3 tag VER1.0, VER1.1, VER2.2, VER2.3 (MP3 only)  
Folder levels: 8, Max folders: 255 (including root folder), Files: 512 (Max. 255 files for one folder)  
01: ASCII, 02: ISO-8859-1, 03: UNICODE (UTF-16 BOM Big Endian), 04: UNICODE (UTF-16 Non-BOM Big  
Endian), 05: UNICODE (UTF-8), 06: UNICODE (Non-UTF-16 BOM Little Endian)  
Displayable character codes*2  
*1  
*2  
Files created with a combination of 48 kHz sampling frequency and 64 kbps bit rate cannot be played.  
Available codes depend on what kind of media, versions and information are going to be displayed.  
4-20 Heater and air conditioner, and audio system  
Troubleshooting guide:  
Symptom  
Cause and Countermeasure  
Check if the disc was inserted correctly.  
Check if the disc is scratched or dirty.  
Check if there is condensation inside the player. If there is, wait until the condensation is gone (about 1 hour) before using the player.  
If there is a temperature increase error, the CD player will play correctly after it returns to the normal temperature.  
If there is a mixture of music CD files (CD-DA data) and MP3/WMA files on a CD, only the music CD files (CD-DA data) will be  
played.  
Cannot play  
Files with extensions other than “.MP3”, “.WMA”, “.mp3” or “.wma” cannot be played. In addition, the character codes and number of  
characters for folder names and file names should be in compliance with the specifications.  
Check if the finalization process, such as session close and disc close, is done for the disc.  
Check if the disc is protected by copyright.  
Check if the disc is scratched or dirty.  
Poor sound quality  
Bit rate may be too low.  
It takes a relatively long time before If there are many folders or file levels on the MP3/WMA disc, or if it is a multisession disc, some time may be required before the  
the music starts playing.  
music starts playing.  
The writing software and hardware combination might not match, or the writing speed, writing depth, writing width, etc., might not  
match the specifications. Try using the slowest writing speed.  
Music cuts off or skips  
Skipping with high bit rate files  
Skipping may occur with large quantities of data, such as for high bit rate data.  
Move immediately to the next song When a non-MP3/WMA file has been given an extension of “.MP3”, “.WMA”, .“mp3” or “.wma”, or when play is prohibited by  
when playing  
copyright protection, there will be approximately 5 seconds of no sound and then the player will skip to the next song.  
The playback order is the order in which the files were written by the writing software. Therefore, the files might not play in the desired  
order.  
Songs do not play back in the  
desired order  
Heater and air conditioner, and audio system 4-21  
ANTENNA  
SAA2102  
Type B  
Removing antenna  
You can remove the antenna if necessary.  
Hold the bottom of the antenna and remove it by  
turning it counterclockwise.  
To install the antenna, turn the antenna clockwise and  
tighten.  
CAUTION:  
.
Be sure to fold down (for Type A) or remove  
the antenna before the vehicle enters  
garage with a low ceiling.  
a
SAA1834  
.
.
Be sure that the antenna is removed before  
the vehicle enters an automatic car wash.  
Type A  
The angle of the antenna can be changed for Type A  
antenna.  
Be sure that the antenna is folded down (for  
Type A) or removed before covering the  
vehicle with a cover.  
4-22 Heater and air conditioner, and audio system  
FM-AM RADIO WITH COMPACT DISC (CD) PLAYER (Type A)  
Audio main operation  
The audio system operates when the ignition switch is  
in the “ACC” or “ON” position.  
Power button/VOL (Volume) control  
knob:  
Power ON/OFF:  
To turn on the audio system, push the Power button.  
.
The system will turn on in the mode that was used  
immediately before the system was turned off.  
.
If the system was turned on with the CD ejected  
and the devices disconnected, the radio will turn  
on.  
To turn off the audio system, push the Power button.  
Volume control:  
To control the volume, turn the VOL (Volume) control  
knob.  
Turn the knob clockwise to make the sound louder.  
Turn the knob counterclockwise to make the sound  
quieter.  
SETUP button:  
JVH0986X  
To configure Audio, Clock, Radio or Language, perform  
the following procedure.  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
DISP (Display) button  
RADIO button  
9.  
CD eject button  
1. Push the  
button.  
10. MEDIA button  
11. Phone button  
2. Turn the MENU knob clockwise or counterclock-  
wise, the display will appear in the following order.  
Day/Night button  
MIX button  
12. Power button /VOL (Volume) control knob  
13. RPT (repeat) button  
Audio Setting  
Language ? Audio Setting  
3. Push the ENTER button to select the item.  
?
Clock  
?
Radio Setting  
?
SEEK button/Rewind button  
SEEK button/Fast forward button  
SETUP button  
14. Radio memory buttons  
15. A-Z button  
Back button  
16. ENTER button/MENU knob  
Heater and air conditioner, and audio system 4-23  
Audio adjustments:  
Adjusting the setting to 0 (zero) turns off the speed  
volume feature. Increasing the speed volume setting  
results in the audio volume increasing more rapidly with  
vehicle speed. Once chosen, push ENTER button to  
save the setting.  
Format:  
Push the  
button and then select “Audio Setting”.  
Switch the clock display between 24-hour mode and  
12-hour clock mode.  
Turn the MENU knob, and the mode will change as  
follows.  
Radio setting:  
Sound ? Aux In ? Speed Vol ? Bass Boost ? Audio  
Default  
Push the  
and then select “Radio”.  
button to enter the setup menu screen  
Bass Boost :  
Set the bass volume between on or off. If set in the  
“ON” position, bass sound is emphasized.  
Push the ENTER button to select the setting you want  
to change. Turn the MENU knob to adjust the selected  
item.  
This function is used to select the FM frequency band.  
Language setting:  
Audio Default :  
Push the  
and then select “Language”.  
button to enter the setup menu screen  
Select this item to reset the audio settings to the  
default value.  
Sound:  
Adjust Bass, Treble, Balance and Fade. Turn the  
MENU knob and then push the ENTER button to select  
the setting item. Turn the MENU knob to adjust the  
setting.  
Select the appropriate language and push the ENTER  
button. Upon completion, the screen will automatically  
adapt the language setting.  
Clock setting:  
Push the  
button to enter the setup menu screen  
and then select “Clock”.  
.
.
.
Bass:  
Turn the MENU knob, and the mode will change as  
follows.  
Day/Night button:  
Enhances or attenuates the bass response sound.  
Push the  
button to switch the display brightness  
Treble:  
Set Time ? ON/OFF ? Format  
Set Time:  
between the daytime and nighttime modes.  
Enhances or attenuates the treble.  
Balance:  
Select “Set Time” and then adjust the clock as follows.  
Phone button:  
Adjusts the balance of the volume between the left  
and right speakers.  
The hour display will start flashing. Turn the MENU  
knob to adjust the hour and push the ENTER button.  
The minute display will start flashing. Turn the MENU  
knob to adjust the minute and push the ENTER button  
to finish the clock adjustment.  
For operation on how to use  
“Bluetooth® Hands-Free Phone System (Type A)”  
(P.4-42).  
button, see  
.
Fade:  
Adjusts the balance of the volume between the  
front and rear speakers.  
MEDIA button:  
Aux In:  
ON/OFF:  
Adjusts the volume output from the auxiliary source.  
Speed Vol (Speed Volume) :  
Push the  
it is connected.  
button to play a compatible device when  
Set the clock display between on or off when the audio  
unit is turned off. If set in the “ON” position, the clock  
will be displayed when the audio unit is turned off  
either by pushing the Power button or when the  
ignition switch is placed in the “OFF” position.  
Each time the  
will change as follows.  
button is pushed, the audio source  
Set the audio system to automatically adjust the  
volume level in relation to vehicle speed.  
CD ? USB/iPod ? Bluetooth audio ? AUX  
A source that is not available will be skipped.  
This mode controls the volume output from the  
speakers automatically in relation to vehicle speed.  
When “Speed Vol” is displayed, turn the MENU knob  
clockwise or anticlockwise to adjust the volume level.  
4-24 Heater and air conditioner, and audio system  
To store the station frequency manually:  
.
An error notification message will be dis-  
played when inserting an incompatible disc  
type (e.g., DVD), or if the player cannot read  
the CD. Eject the disc and insert another  
disc.  
Radio operation  
The audio system operates when the ignition switch is  
in the “ACC” or “ON” position.  
1. Tune to the desired broadcasting station fre-  
quency by using the  
buttons.  
2. Push and hold a radio memory button  
to  
RADIO button:  
until a beep sounds. (The radio mutes when  
the memory button is pushed.)  
When the  
button is pushed while the audio  
MEDIA button:  
3. The channel indicator will display and the radio  
mute disengages, indicating that the memory is  
stored properly.  
system is off, the audio system will turn on and the  
radio will turn on.  
To change to the CD mode, push the  
a CD inserted until the CD mode is selected.  
button with  
When the  
button is pushed while another audio  
4. Perform steps 1 - 3 for all other memory buttons.  
List view:  
source is playing, the other audio source will turn off  
and the radio will turn on.  
While the track is being played, push either the ENTER  
button or the  
in the list. To select a track from the list, or a track to  
start listening to, turn the MENU knob and then push  
the ENTER button.  
If the battery cable is disconnected, or if the audio fuse  
blows, the radio memory will be erased. In such a case,  
reset the desired stations.  
button to display the available track  
To change the radio bands, push the  
the desired band appears.  
button until  
button to  
FM 1 ? FM 2 ? AM ? FM 1  
CD player operation  
The audio system operates when the ignition switch is  
in the “ACC” or “ON” position.  
During FM reception, push and hold the  
update FM list.  
Quick search:  
In the list view mode, a quick search can be performed  
to find a track from the list. Push the A-Z button, turn  
the MENU knob to the first alphabetic letter of the song  
title, and then push the ENTER button. When found, a  
list of the available songs will be displayed. Select, and  
push the ENTER button to play the preferred track.  
Turn the MENU knob to select a station from the FM  
list.  
Loading:  
Insert a CD into the slot with the label side facing up.  
The CD will be guided automatically into the slot and  
will start playing. After loading the CD, the number of  
tracks and the play time will appear on the display.  
SEEK buttons:  
When adjusting the broadcasting station frequency  
manually, push the  
frequency is achieved.  
or  
button until the desired  
CAUTION:  
Fast forward/Rewind buttons:  
Do not force the CD into the slot. This could  
damage the player.  
When adjusting the broadcasting station frequency  
automatically, push and hold the or button.  
When the system detects a broadcasting station, it will  
stop at the station.  
Push and hold the  
or rewind through the track. When the button is  
released, the track will play at normal playing speed.  
or  
button to fast forward  
NOTE:  
Track up/down:  
.
The CD player accepts normal audio CDs or  
CDs containing MP3/WMA files.  
to  
Radio memory buttons:  
By pushing the  
skip forward to the next track or backward to the  
beginning of the current track. Push the or  
button more than once to skip through the tracks.  
or  
button once, the track will  
During radio reception, pushing the radio memory  
button will select the stored radio station.  
.
The audio unit will automatically detect if a  
CD containing MP3/WMA files is inserted,  
and “MP3CD” will be indicated.  
The audio system can store up to 12 FM station  
frequencies (6 in each of FM 1, FM 2) and 6 AM  
station frequencies.  
Heater and air conditioner, and audio system 4-25  
Folder browsing:  
device into the connector. The USB memory device  
will be activated automatically.  
DISP button:  
If the recorded media contains folders with music files,  
While a CD with title information is being played, the  
title of the played track is displayed.  
pushing the  
each folder in sequence.  
or  
button will play the tracks of  
If the system has been turned off while the USB  
memory device was playing, pushing the Power button  
will start the USB memory device.  
When the  
button is pushed repeatedly while a CD  
To select a preferred folder:  
with MP3/WMA/AAC is playing, further information  
about the track can be displayed along with the track  
title as follows.  
The following operations are identical to the audio main  
operation of the Compact Disc (CD) operation. For  
details, see “CD player operation” (P.4-25).  
1. Push the ENTER button or the  
button and a  
list of tracks in the current folder is displayed.  
2. Push the  
button.  
Track time ? Artist ? Album ? Track time  
.
.
.
.
.
.
List view  
3. Turn the MENU knob for the preferred folder.  
Quick search  
Track details:  
4. Push the ENTER button to access the folder. Push  
the ENTER button again to start playing the first  
track or turn the MENU knob, and push the  
ENTER button to select another track.  
Pushing and holding the  
display into a detailed overview. Push the  
button will turn the  
button  
MIX (Random play)  
RPT (Repeat track)  
Folder browsing  
to return to the display for the main display mode.  
If the current selected folder contains sub folders, push  
the ENTER button, and a new screen with a list of sub  
folders will be displayed. Turn the MENU knob for the  
sub folder and then push the ENTER button to select.  
Select the root folder item when songs are recorded  
additionally in the root folder.  
CD Eject button:  
MEDIA button:  
When the  
button is pushed while a CD is loaded,  
the CD will be ejected.  
To change to the USB mode, push the  
button  
with a USB connected until the USB mode is selected.  
When the  
button is pushed twice, the CD will be  
ejected further, and the CD can be removed with ease.  
To return to the previous folder screen, push the  
button.  
DISP button:  
When the ignition switch is in the “OFF” or “LOCK”  
position it is possible to eject the CD currently being  
played. However the audio unit will not be activated.  
While a track with recorded music information tags  
(ID3-tags) is being played, the title of the played track  
is displayed. If the tags are not provided then a  
notification message is displayed.  
RPT button:  
If a CD is ejected by pushing the  
button, and it is  
not taken out from the loading slot within 8 seconds,  
the CD will automatically be reloaded to the slot in  
order to protect the CD.  
Push the  
button and the current track will be  
played continuously.  
When the  
button is pushed continuously, further  
information about the track can be displayed along  
with the track title as follows.  
MIX button:  
USB device operation  
Track time ? Artist ? Album ? Track time  
Push the  
button and all the tracks will be played in  
USB main operation:  
a random order.  
Track details:  
The audio system operates when the ignition switch is  
placed in the “ON” or “ACC” position.  
Pushing and holding the  
display into a detailed overview. Push the  
to return to the display for the main display mode.  
button will turn the  
button  
The USB port is located on the lower part of the  
instrument panel. See “USB (Universal Serial Bus)  
Connection Port” (P.4-40). Connect a USB memory  
4-26 Heater and air conditioner, and audio system  
iPod main operation:  
display into a detailed overview. To return to the main  
display, push the button.  
iPod player operation  
Interface:  
Connecting iPod:  
Bluetooth® audio player operation  
The interface for iPod operation shown on the audio  
system display is similar to the iPod interface. Use the  
ENTER button/MENU knob to play a track on the iPod.  
The USB port is located on the lower part of the  
instrument panel. See “USB (Universal Serial Bus)  
Connection Port” (P.4-40).  
Regulatory information:  
Bluetooth® is a trademark owned  
by Bluetooth SIG, Inc. and li-  
censed to Visteon Corporation.  
The following items can be chosen from the menu list  
screen.  
When the iPod is connected to the vehicle, the iPod  
music library can only be operated by the vehicle audio  
controls.  
.
.
.
.
Playlists  
Artist  
CE statement:  
* iPod and iPhone are a trademark of Apple Inc.,  
registered in the U.S. and other countries.  
Hereby Visteon Corp. declares that this system is in  
compliance with the essential requirements and other  
relevant provisions of Directive 1999/5/EC.  
Albums  
Songs  
Compatibility:  
For further information about each item, see the iPod  
owner’s manual.  
The system unit shall be compatible with all devices  
(past and future) supporting Apple Accessory Protocol  
on USB link.  
The following operations are identical to the audio main  
operation of the Compact Disc (CD) operation. For  
details, see “CD player operation” (P.4-25).  
It includes (and not limited to):  
NOTE:  
.
.
.
.
.
.
iPod Generation 5 devices  
The audio system only supports Bluetooth®  
devices with AVRCP (Audio Video Remote Con-  
trol Profile) version 1.3, or 1.0 or earlier.  
.
.
.
.
.
.
List view  
iPod Classic I and II (Generation 6 and 7)  
iTouch Generaion OS 1, 2, 3, 4 and next  
iPhone Generation OS 1, 2, 3, 4 and next  
iPod Nano (1G, 2G, 3G)  
Quick search  
Bluetooth® audio player main operation:  
MIX (Random play)  
RPT (Repeat track)  
Folder browsing  
iPad 1, 2 and 3  
NOTE:  
This audio system does not support iPad char-  
ging.  
DISP button:  
While a track with recorded music information tags  
(ID3-tags) is being played, the title of the played track  
is displayed.  
MEDIA button:  
To operate the iPod, push the  
until the USB/iPod mode is selected and then push the  
ENTER button.  
button repeatedly  
When the  
button is pushed repeatedly, further  
information about the track can be displayed along  
with the track title as follows:  
JVH0848X  
Track time ? Artist ? Album ? Track time  
To play Bluetooth® audio, the Bluetooth® audio device  
needs to be paired to the in-vehicle system. For the  
pairing operation, see “Setting items” (P.4-43).  
Track details:  
Pushing and holding the  
button will turn the  
Heater and air conditioner, and audio system 4-27  
AUX device player operation  
MEDIA button:  
The AUX input jack is located on the lower part of the  
instrument panel. (See “AUX (auxiliary) Input Jack”  
(P.4-41).) The AUX audio input jack accepts any  
standard analog audio input such as from a portable  
cassette tape/CD player, MP3 player or laptop  
computer.  
To operate the Bluetooth® audio streaming, push the  
button repeatedly until “BT Audio” is shown.  
A
B
The type of display,  
or  
, shown on the audio  
*
*
system can vary depending on the Bluetooth® version  
of the device.  
Push the  
selected, to play  
button repeatedly until the AUX mode is  
compatible device when it is  
Fast forward/Rewind buttons:  
a
plugged into the AUX input jack.  
When  
or  
button is pushed continuously, the  
track will be played at high speed. When the button is  
released, the track will be played at normal playing  
speed.  
NISSAN strongly recommends using a stereo mini  
plug cable when connecting your music device to the  
audio system. Music may not play properly when a  
monaural cable is used.  
Track up/down:  
By pushing the  
skip forward to the next track or backward to the  
beginning of the current track. Push the or  
or  
button once, the track will  
button more than once to skip through the tracks.  
DISP button:  
If the song contains music information tags (ID3–  
tags), the title of the played song will be displayed. If  
tags are not provided then the display will not show  
any messages.  
When the  
button is pushed repeatedly further  
information about the song can be displayed along  
with the song title.  
A long push of  
detailed overview which after a few seconds returns to  
the main display; or push button briefly.  
button will turn the display into a  
4-28 Heater and air conditioner, and audio system  
17. ENTER/SETTING button  
FM-AM RADIO WITH COMPACT DISC (CD) PLAYER (Type B)  
JVH0866X  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
DISP (display) button  
MEDIA button  
9.  
SCAN button  
10. SEEK TRACK (forward) button  
11. BACK button  
CD eject button  
FM·AM button  
12. Power button/VOL (volume) control knob  
13. RPT (repeat) button  
CD button  
Color display  
14. RDM (random) button  
Apps button  
15. Radio memory buttons  
16. TUNE FOLDER knob  
SEEK TRACK (rewind) button  
Heater and air conditioner, and audio system 4-29  
.
.
AUX Vol.  
24 hour clock is not available.  
On-Screen Clock  
Audio main operation  
Controls the volume level of incoming sound when  
an auxiliary device is connected to the system.  
Choose a setting between 1 and 3 or choose 0 to  
disable the feature entirely.  
.
Head unit:  
When this item is turned on, a clock is always  
displayed in the upper right corner of the screen.  
The auto loudness circuit enhances the low and high  
frequency ranges automatically in both radio reception  
and CD playback.  
Select the “On-Screen Clock” using the TUNE  
FOLDER knob and then push the ENTER/  
SETTING button. You can toggle between ON  
and OFF using the TUNE FOLDER knob.  
Brightness and Contrast  
Adjust the brightness and contrast of the screen.  
Power button/VOL (volume) control knob:  
Select “Brightness” or “Contrast” using the TUNE  
FOLDER knob and then push the ENTER/  
SETTING button. Turn the TUNE FOLDER knob  
to adjust the brightness and contrast of the screen  
to the preferred level.  
Push the Power button to turn the audio system on and  
off while the ignition switch is placed in the “ON” or  
“ACC” position.  
.
.
RDS Display  
RDS (radio data system) information can be  
shown on the display. Select “RDS Display” using  
the TUNE FOLDER knob and then push the  
ENTER/SETTING button. You can toggle between  
ON and OFF using the TUNE FOLDER knob.  
Turn the VOL (volume) control knob to adjust the  
volume.  
.
Clock Adjust  
Adjust the clock according to the following  
procedure.  
Audio settings:  
Language Select  
The settings screen will appear when the ENTER/  
SETTING button is pushed.  
The language settings can be changed.  
Select “Language Select” using the TUNE  
FOLDER knob and then push the ENTER/  
SETTING button. Use the TUNE FOLDER knob  
to select the preferred language.  
The following items are available in the settings screen.  
.
Bluetooth  
It is possible to set the Bluetooth® settings. For  
details of the Bluetooth® settings, see “Bluetooth®  
audio player operation” (P.4-33).  
DISP button:  
.
Bass, Treble, Balance and Fade  
Display of the screen can be canceled by pushing the  
button. You can still listen to music that is being  
played back even while the screen display is turned off.  
If you want to display the screen again, either push the  
Controls the sound of the audio system. Balance  
adjusts the sound between the left and right  
speakers. Fade adjusts the sound between the  
front and rear speakers.  
JVH0867X  
button once more or push the  
button accordingly.  
,
,
,
1) Select “Clock Adjust” using the TUNE  
Select the “Bass”, “Treble”, “Balance” or “Fade”  
using the TUNE FOLDER knob, and then push the  
ENTER/SETTING button. Turn the TUNE  
FOLDER knob to adjust the Bass, Treble, balance  
and Fade of the screen to the preferred level.  
1
FOLDER knob  
and then push the  
*
2
*
ENTER/SETTING button  
.
MEDIA button:  
2) Adjust the hour with the TUNE FOLDER knob  
1
and then push the ENTER/SETTING  
*
Pushing the  
as follows:  
button will switch the audio source  
2
*
button  
.
.
Speed Sens Vol.  
3) Adjust the minute with the TUNE FOLDER  
To change the Speed Sensitive Volume (Speed  
Sens Vol.) level from off (0) to 5, turn the TUNE  
FOLDER knob.  
USB/iPod? Bluetooth ? AUX? USB/iPod  
1
knob  
and then push the ENTER/  
*
2
*
SETTING button  
.
4-30 Heater and air conditioner, and audio system  
Radio operation  
CD player operation  
SEEK TRACK buttons:  
or button to tune from low to high  
or high to low frequencies and to stop at the next  
broadcasting station.  
Place the ignition switch in the “ON” or “ACC”  
position, and insert the compact disc (CD) into the  
slot with the label side facing up. The CD will be  
guided automatically into the slot and start playing.  
Frequency range and step change:  
Push the  
To change the frequency range and step specification  
of the radio, perform the following operations.  
1. Push the ENTER/SETTING button with the audio  
system off.  
After loading the CD, the number of tracks on the CD  
and the play time will appear on the display.  
SCAN buttons:  
2. Select “Radio Frequency Range and Step” and  
push the ENTER/SETTING button.  
Push the  
button to tune from low to high  
If the radio is already operating, it will automatically turn  
off and the CD will play.  
frequencies and stop at each broadcasting station  
for several seconds. Pushing the button again during  
this several seconds period will stop SCAN tuning and  
the radio will remain tuned to that station.  
3. Turn the TUNE/FOLDER knob until appropriate  
region is highlighted, and push the ENTER/  
SETTING button.  
If the system was turned off while the CD was playing,  
pushing the Power button will start the CD.  
If the  
button is not pushed within 5 seconds,  
button:  
FM·AM button:  
SCAN tuning moves to the next station.  
When the  
button is pushed with the system off  
Push the  
button to change the band as follows:  
to Radio memory buttons:  
and the CD loaded, the system will turn on and the CD  
will start to play.  
AM ? FM1 ? FM2? AM  
Up to 12 stations can be set for the FM band (6 each  
for FM1 and FM2) and 6 stations can be set for the AM  
band.  
TUNE (Tuning):  
When the  
button is pushed with the CD loaded  
and the radio playing, the radio will automatically be  
turned off and the CD will start to play.  
Turn the TUNE FOLDER knob for manual tuning.  
1. Choose the radio band using the  
2. Tune to the desired station.  
button.  
Radio Data System (RDS) :  
RDS stands for Radio Data System, and is a data  
information service transmitted by some radio stations  
on the FM band (not AM band) encoded within a  
regular radio broadcast. Currently, most RDS stations  
are in large cities, but many stations are now  
considering broadcasting RDS data.  
SEEK TRACK (rewind/forward)  
buttons:  
3. Push and hold the desired station preset button  
to until the radio mutes.  
When the  
or  
button is pushed and held while  
4. The station indicator will then come on and the  
sound will resume. The station is now set to the  
button memory.  
the CD is being played, the CD will play while fast  
forwarding or rewinding. When the button is released,  
the CD will return to normal play speed.  
RDS can display:  
5. Other buttons can be set in the same manner.  
When the  
or  
button is pushed for less than  
.
.
Station name, such as “The Groove”.  
If the battery cable is disconnected, or if the fuse  
opens, the station memory will be erased. In that case,  
reset the desired stations.  
1.5 seconds while the CD is being played, the next  
track or the beginning of the current track on the CD  
will be played.  
Music or programming type such as “Classical”,  
“Country” or “Rock”.  
Push the  
or  
button more than once to skip  
through the tracks.  
Heater and air conditioner, and audio system 4-31  
can only be operated by the vehicle audio controls.  
USB device operation  
RPT (repeat) button:  
When the button is pushed while the CD is  
* iPod and iPhone are a trademark of Apple Inc.,  
registered in the U.S. and other countries.  
USB main operation:  
The audio system operates when the ignition switch is  
placed in the “ON” or “ACC” position.  
played, the play pattern can be changed as follows:  
Refer to your device manufacturer’s owner information  
regarding the proper use and care of the device.  
(CD)  
The USB port is located on the lower part of the  
instrument panel. See “USB (Universal Serial Bus)  
Connection Port” (P.4-40). Connect a USB memory  
device into the connector. The USB memory device  
will be activated automatically.  
(Normal) ⇔ 1 Track Repeat  
(CD with compressed audio files)  
Compatibility:  
The following models are compatible:  
(Normal) ? 1 Folder Repeat ? 1 Track Repeat ?  
(Normal)  
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
iPod nano 1G (Firmware version 1.3.1 -)  
iPod nano 2G (Firmware version 1.1.3 -)  
iPod nano 3G (Firmware version 1.0.0 -)  
iPod nano 4G (Firmware version 1.0.2 -)  
iPod nano 5G (Firmware version 1.0.1 -)  
iPod nano 6G (Firmware version 1.0 -)  
iPod nano 7G (Firmware version 1.0.0 -)  
iPod 5G (Firmware version 1.2.1 -)  
iPod classic (Firmware version 1.0.0 -)  
iPod Touch (iOS 1.1 -)  
If the system has been turned off while the USB  
memory device was playing, pushing the ENTER/  
SETTING button will start the USB memory device.  
RDM (random) button:  
When the  
button is pushed while a CD is being  
The following operations are identical to the audio main  
operation of the Compact Disc (CD) operation. For  
details, see “CD player operation” (P.4-31).  
played, the play pattern can be changed as follows:  
(CD)  
(Normal) ⇔ 1 Disc Random  
(CD with compressed audio files)  
.
.
.
RDM (Random play)  
RPT (Repeat track)  
(Normal) ? 1 Disc Random ? 1 Folder Random ?  
(Normal)  
iPod Touch 2G (iOS 2.1.1 -)  
iPod Touch 3G (iOS 3.1 -)  
MEDIA button:  
iPod Touch 4G (iOS 4.1 -)  
CD eject button:  
To change to the USB mode, push the  
with a USB connected until the USB mode is selected.  
button  
iPod Touch 5G (iOS 6.0.0 -)  
When the  
button is pushed with the CD loaded,  
iPhone (iOS 1.0.0 - 2.2.1)  
the CD will be ejected.  
iPod player operation  
iPhone 3G (iOS 2.1 -)  
When this button is pushed while the CD is being  
played, the CD will be ejected.  
iPhone 3GS (iOS 3.0 -)  
Connecting iPod:  
iPhone 4/4S (iOS 4.0 -)  
The USB port is located on the lower part of the  
instrument panel. Connect the iPod with a USB port  
If the CD comes out and is not removed, it will be  
pulled back into the slot to protect it.  
iPhone 5 (iOS 6.0.0 -)  
using  
a
cable. See “USB (Universal Serial Bus)  
Operations attributable to firmware update by Apple  
are not guaranteed.  
Connection Port” (P.4-40). The battery of the iPod is  
charged while the cable is connected to the vehicle.  
Depending on the version of the iPod, the display on  
the iPod shows a NISSAN or Accessory Attached  
screen when the connection is completed. When the  
iPod is connected to the vehicle, the iPod music library  
4-32 Heater and air conditioner, and audio system  
iPod main operation:  
released, the iPod will return to the normal play speed.  
When the or button is pushed for less than  
Regulatory information:  
Bluetooth® trademark:  
The system operates when the ignition switch is in the  
“ON” or “ACC” position. Push the  
repeatedly to switch to the iPod mode.  
button  
Bluetooth® is a trademark owned  
by Bluetooth SIG, Inc. and li-  
censed to Visteon Corporation.  
1.5 seconds while the iPod is playing, the next track or  
the beginning of the current track on the iPod will be  
played.  
If the system was turned off while the iPod was playing,  
pushing the Power button will start the iPod.  
Push the  
or  
button more than once to skip  
Connecting Bluetooth® device:  
To connect your Bluetooth® device to the vehicle,  
through the tracks.  
If another audio source is playing and the iPod is  
connected, pushing the  
button repeatedly will  
follow the procedure below:  
change the system to the iPod mode.  
RPT (repeat) button:  
When the button is pushed while a track is being  
1. Push the ENTER/SETTING button.  
When the  
is pushed while the iPod is connected,  
the interface for iPod operation is shown on the audio  
display. The items on the menu list can be scrolled by  
turning the TUNE FOLDER knob while the iPod is  
operating. To select an item, push the ENTER/  
SETTING button. Items in the iPod menu appear on  
the display in the following order.  
played, the play pattern can be changed as follows:  
Repeat Off ? 1 Track Repeat? All Repeat ? Repeat  
Off  
RDM (random) button:  
.
.
.
.
.
.
.
.
.
.
Now playing  
Playlists  
When the  
button is pushed while a track is being  
played, the play pattern can be changed as follows:  
Artists  
Shuffle Off ? Track Shuffle ? Shuffle Off  
Albums  
JVH0620X  
Songs  
BACK button:  
2. Select “Bluetooth” .  
Podcasts  
Genres  
The display will return to the previous screen.  
3. Select “Add Phone or Device” . This same screen  
can be accessed to remove, replace or select a  
different Bluetooth® device.  
Bluetooth® audio player operation  
Composers  
Audiobooks  
Shuffle Songs  
If you have a compatible Bluetooth® audio device that  
is capable of playing audio files, the device can be  
connected to the vehicle’s audio system so that the  
audio files on the device play through the vehicle’s  
speakers.  
4. The system acknowledges the command and asks  
you to initiate a connection from the Bluetooth®  
device. The procedure for connecting a Blue-  
tooth® device varies according to the cellular  
phone model. See the Owner’s manual of the  
Bluetooth® device for details.  
For more information about each item, see the iPod  
Owner’s Manual.  
SEEK TRACK (rewind/forward)  
buttons:  
When the  
or  
button is pushed for more than  
1.5 seconds while the iPod is playing, the iPod will play  
while fast forwarding or rewinding. When the button is  
Heater and air conditioner, and audio system 4-33  
Bluetooth® audio main operation:  
.
.
For vehicles without Navigation, Apple  
iPhones must be paired via Bluetooth® for  
NissanConnect Apps to function.  
NissanConnect App smartphone integration  
This vehicle is equipped with Smartphone Integration  
technology. This allows many compatible Smartphone  
applications to be displayed and easily controlled  
through the audio display.  
For Android phones, NissanConnect Apps  
REQUIRES the phone to be paired via Blue-  
tooth®.  
NOTE:  
The registration of a compatible smartphone is  
required to use mobile applications or to access  
connected features of certain vehicle applica-  
tions.  
Apps button:  
The  
mode.  
button launches the Smartphone Integration  
Application download:  
Registering with NissanConnect App:  
JVH1012X  
Once connected, the NissanConnect Mobile App will  
search your phone to determine which compatible  
applications are currently installed. The vehicle will  
then download the in-vehicle interface for each of  
these compatible applications. Once downloaded, the  
user can access many smartphone Applications  
through the vehicle audio screen. For more information  
on application availability visit the NissanConnect  
website.  
To use the Smartphone Integration feature, it is  
necessary for the user to register with NissanConnect.  
In order to register, visit the NissanConnect website for  
more information and to sign up. Once registered,  
download the NissanConnect Mobile App from your  
compatible phone’s application download source and  
then log in to the application.  
To switch to the Bluetooth® audio mode, push the  
button repeatedly until the Bluetooth® audio mode is  
displayed on the screen.  
The controls for the Bluetooth® audio are displayed on  
the screen. Use the Preset  
button to play and use  
the Preset button to pause.  
AUX device player operation  
For Mexico:  
The AUX input jack is located on the lower part of the  
instrument panel. (See “AUX (auxiliary) Input Jack”  
(P.4-41).) The AUX audio input jack accepts any  
standard analog audio input such as from a portable  
cassette tape/CD player, MP3 player or laptop  
computer.  
For more information about this technology, visit the  
website www.nissan.com.mx/connect or www.nissan-  
connect.com.mx or contact NISSAN Customer Service  
01 800 964 77 26 (01 800 9 NISSAN).  
Connecting phone:  
NISSAN strongly recommends using a stereo mini  
plug cable when connecting your music device to the  
audio system. Music may not play properly when a  
monaural cable is used.  
To use this feature, a compatible smartphone must be  
connected via Bluetooth® or USB to the vehicle. For  
the Bluetooth® connecting procedure, see “Bluetooth®  
Hands-Free Phone System (Type B)” (P.4-48).  
NOTE:  
.
For Apple iPhones, NissanConnect Apps  
REQUIRES the phone to be plugged in via  
USB.  
4-34 Heater and air conditioner, and audio system  
FM-AM RADIO WITH COMPACT DISC (CD) PLAYER (Type C)  
Audio main operation  
The audio system operates when the ignition switch is  
placed in the “ON” or “ACC” position.  
Power/VOL (volume) dial:  
Push Power/VOL (volume) dial to turn on and off the  
audio system.  
Turn the Power/VOL (volume) dial to adjust the volume.  
This vehicle may be equipped with Speed Sensitive  
Volume (SSV) function for audio. When this function is  
turned on, the audio volume will be adjusted auto-  
matically as the vehicle speed changes. For operations  
to turn on and off the SSV function, see “Audio  
settings” (P.4-5).  
Audio settings:  
For the operations to adjust the audio settings, see  
“Audio settings” (P.4-5).  
Traffic Announcement:  
Touch “TA” on the audio screen to turn on or off the  
Traffic Information setting. When it is turned on, the  
Traffic Information will interrupt the music that was  
playing and informs the driver of the received traffic  
information.  
Radio operation  
JVH0982X  
The audio system operates when the ignition switch is  
placed in the “ON” or “ACC” position.  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
CD button  
9.  
Back button  
Disc eject button  
FM·AM button  
10. SETUP button  
Radio band select button:  
Push the FM·AM button to change the band as follows:  
For Mexico:  
Disc insert slot  
Seek/Track buttons  
Power/VOL (volume) dial  
AUX (auxiliary) button  
Enter/Scroll dial  
AM ? FM1 ? FM2 ? AM  
Heater and air conditioner, and audio system 4-35  
For the Middle East:  
For FM , touch the “7-12” key to display the 7 - 12  
memory keys.  
through the tracks on the CD. If the last track on a CD  
is skipped, the first track on the disc will play. If the last  
track in a folder of an MP3 CD is skipped, the first track  
of the next folder will play.  
AM ? FM ? AM  
3. The channel indicator will then come on and the  
sound will resume. Programming is now complete.  
If another audio source is playing when the FM·AM  
button is pushed, the audio source playing will  
automatically be turned off and the last radio station  
played will begin playing.  
CD/MP3/WMA display mode:  
CD player operation  
While listening to a CD or an MP3/WMA CD, certain  
text may be displayed (when a CD encoded with text is  
being used). Depending on how the CD or MP3/WMA  
CD is encoded, the text is displayed listing the artist,  
album and song title. Operation keys are also  
displayed on the screen.  
Loading disc:  
Radio tuning:  
Insert a CD into the slot with the label side facing up.  
The CD will be guided automatically into the slot and  
will start playing. If the radio is already playing, it will  
automatically turn off, and the CD will start playing.  
When in radio mode, the radio can be tuned using the  
touchscreen. To bring up the visual tuner, touch the  
“Tune” key on the lower part of the screen. A screen  
appears with a bar running from low frequencies on the  
left to high frequencies on the right.  
Random/Mix:  
CAUTION:  
Touching the “Random/Mix” key while an CD or MP3  
CD is playing will alternate the random play pattern as  
follows:  
One of the following operations can be used for tuning.  
Do not force the compact disc into the slot. This  
could damage the player.  
.
.
.
Touching the bar on the screen  
Touching “ ”/“ ” on the screen  
Turning Enter/Scroll dial  
(CD)  
button:  
(Normal) ? Random/Mix ? (Normal)  
(CD with compressed audio files)  
(Normal) ? Random Folder ? Random All ? (Normal)  
Repeat:  
To return to the regular radio display screen, touch the  
“OK” key.  
When the CD button is pushed with the system off and  
the CD loaded, the system will turn on and the CD will  
start to play.  
Station List:  
When in FM mode, touch “FM List” to display the  
station lists.  
When the CD button is pushed with a CD loaded while  
the radio playing, the radio will turned off and the CD  
will start to play.  
Touching the “Repeat” key while an CD or MP3 CD is  
playing will alternate the repeat play pattern as follows:  
Seek/Track buttons:  
(CD)  
(Normal) ? Repeat ? (Normal)  
(CD with compressed audio files)  
When in radio mode, push the Seek/Track buttons to  
tune from low to high or high to low frequencies and to  
stop at the next broadcasting station.  
Seek/Track button:  
When the  
or  
button is pushed for more than  
(Normal)  
(Normal)  
?
Repeat Track  
?
Repeat Folder  
?
1.5 seconds while the CD is being played, the CD will  
play while fast forwarding or rewinding. When the  
button is released, the CD will return to normal play  
speed.  
Station memory keys:  
Up to 6 stations can be stored for AM band, and up to  
12 stations can be stored for each of the other bands.  
Browse:  
Touch the “Browse” key to display the titles on the CD  
in list format. Touch the title of a song in the list to  
begin playing that song. If an MP3 CD is playing,  
touching the “Browse” key will also list the folders on  
the disc. Touch the “Folder Up” key to view the lists in  
When the  
or  
button is pushed for less than  
1. Choose the radio band.  
1.5 seconds while the CD is being played, the next  
track or the beginning of the current track on the CD  
will be played. Push the button several times to skip  
2. Tune to the desired station using manual or seek  
tuning. Touch and hold any of the desired station  
memory keys until a beep sound is heard.  
4-36 Heater and air conditioner, and audio system  
the upper layer. Follow the procedure for selecting a  
song with the touchscreen to choose a folder.  
USB screen operation:  
iPod player operation  
While files on a USB memory device are playing, the  
play pattern can be altered so that songs are repeated  
or played randomly.  
Connecting iPod:  
The USB port is located on the lower part of the  
instrument panel. See “USB (Universal Serial Bus)  
Connection Port” (P.4-40).  
Disc eject button:  
Random/Mix:  
When the Disc eject button is pushed while a CD is  
loaded, the CD will be ejected.  
Touching the “Random/Mix” key on the screen while an  
USB memory device is playing will alternate the  
random play pattern as follows:  
If your iPod supports charging via a USB connection,  
its battery will be charged while connected to the  
vehicle with the ignition switch placed in the “ON” or  
“ACC” position.  
If the CD is not removed within 10 seconds, the CD  
will be reloaded.  
(Normal) ? Random Folder ? Random All ? (Normal)  
USB device operation  
The audio system operates when the ignition switch is  
placed in the “ON” or “ACC” position.  
Compatibility:  
Repeat:  
The following models are compatible:  
Touching the “Repeat” key on the screen while an USB  
memory device is playing will alternate the repeat play  
pattern as follows:  
.
.
.
.
.
.
.
.
.
.
.
iPod Classic 5th Generation (firmware version  
1.3.0 or later)  
The USB port is located on the lower part of the  
instrument panel. See “USB (Universal Serial Bus)  
Connection Port” (P.4-40). Connect a USB memory  
device into the connector. The USB memory device  
will be activated automatically.  
(Normal)  
(Normal)  
?
Repeat Track  
?
Repeat Folder  
?
iPod Classic 6th Generation (firmware version  
2.0.1 or later)  
iPod Classic 7th Generation (firmware version  
2.0.4 or later)  
Browse:  
Refer to your device manufacturer’s owner information  
regarding the proper use and care of the device.  
Touch “Browse” key to display USB interface. Select  
the songs you wish to play by touching the item on the  
screen.  
iPod Touch 2nd Generation (firmware version  
4.2.1or later)*  
USB main operation:  
iPod Touch 3rd Generation (firmware version 5.1  
or later)*  
If another audio source is playing and a USB memory  
device is inserted, push the AUX button until the  
screen on the display changes to the USB memory  
mode.  
Seek/Track buttons:  
iPod Touch 4th Generation (firmware version  
5.11or later)*  
Push the  
button while an audio file on the USB  
memory device is playing to return to the beginning of  
the current track. Push the button several times to skip  
backward several tracks.  
iPod nano - 1st generation (firmware version 1.3.1  
or later)  
If the system has been turned off while the USB  
memory device was playing, push the Power/VOL  
(volume) dial to restart the USB memory device.  
iPod nano - 2nd generation (firmware version  
1.1.3 or later)  
Push the  
button while an audio file on the USB  
memory device is playing to advance one track. Push  
the button several times to skip forward several tracks.  
if the last track on the USB memory device is skipped,  
the first track of the next folder is played.  
Touch the name of a song on the screen to begin  
playing that song.  
iPod nano - 3rd generation (firmware version 1.1.3  
or later)  
iPod nano - 4th generation (firmware version 1.0.4  
or later)  
iPod nano - 5th generation (firmware version 1.0.2  
or later)  
Heater and air conditioner, and audio system 4-37  
.
iPod nano - 6th generation (firmware version 1.1  
or later)  
screen.  
If no character is selected after thirty seconds, the  
display returns to normal.  
When the iPod is playing, touch the “Menu” key to  
bring up the iPod interface.  
.
.
.
.
iPhone 3G (firmware version 4.2.1or later)  
iPhone 3GS (firmware version 5.1 or later)  
iPhone 4 (firmware version 5.1 or later)  
iPhone 4S (firmware version 5.1 or later)  
Random and repeat play mode:  
Depending on the iPod model, the following items may  
be available on the menu list screen. For further  
information about each item, see the iPod Owner’s  
Manual.  
While the iPod is playing, the play pattern can be  
altered so that songs are repeated or played randomly.  
Shuffle/Mix:  
* Some features of this iPod may not be fully functional.  
Touching the “Shuffle/Mix” key on the screen while an  
iPod is playing will alternate the random play pattern as  
follows:  
.
.
.
.
.
.
.
.
Playlists  
Artists  
Make sure that your iPod firmware is updated to the  
version indicated above.  
Albums  
iPod main operation:  
(Normal) ? Shuffle Songs/Mix songs ? (Normal)  
Genres  
If the system has been turned off while the iPod was  
playing, pushing the Power/VOL (volume) dial will start  
the iPod.  
Repeat:  
Songs  
Touching the “Repeat” key on the screen while an iPod  
is playing will alternate the repeat play pattern as  
follows:  
Composers  
Audiobooks  
Podcasts  
If another audio source is playing and a iPod is  
connected, push the AUX button until the screen on  
the display changes to the iPod mode.  
(Normal) ? Repeat Song ? (Normal)  
Scrolling menus:  
Refer to your device manufacturer’s owner information  
regarding the proper use and care of the device.  
Seek/Track buttons:  
Push the Seek/Track (rewind) or Seek/Track (fast  
forward) button to skip backward or forward one track.  
Interface operation:  
Push and hold the Seek/Track (rewind) or Seek/Track  
(fast forward) button for 1.5 seconds while a track is  
playing to reverse or fast forward the track being  
played. The track plays at an increased speed while  
reversing or fast forwarding. When the button is  
released, the track returns to normal play speed.  
Bluetooth® audio player operation  
JVH0681X  
If you have a compatible Bluetooth® audio device that  
is capable of playing audio files, the device can be  
connected to the vehicle’s audio system so that the  
audio files on the device play through the vehicle’s  
speakers.  
While navigating long lists of artists, albums or songs  
in the music menu, it is possible to scroll the list by the  
first character in the name. To activate character  
indexing, touch the “A-Z” key in the upper right corner  
of the screen. Turn the ENTER/Scroll dial to choose  
the number or letter to jump to in the list and then push  
the ENTER/Scroll dial.  
JVH0680X  
The interface for iPod operation shown on the vehicle’s  
audio system display screen is similar to the iPod  
interface. Use the touchscreen, BACK button or the  
ENTER/Scroll dial to navigate the menus on the  
4-38 Heater and air conditioner, and audio system  
Bluetooth® trademark:  
Bluetooth® is a trademark owned  
then log in to the application.  
For Mexico:  
AUX device player operation  
The AUX input jack is located on the lower part of the  
instrument panel. (See “AUX (auxiliary) Input Jack”  
(P.4-41).) The AUX audio input jack accepts any  
standard analog audio input such as from a portable  
cassette tape/CD player, MP3 player or laptop  
computer.  
by Bluetooth SIG, Inc. and li-  
censed to Bosch.  
For more information about this technology, visit the  
website www.nissan.com.mx/connect or www.nissan-  
connect.com.mx or contact NISSAN Customer Service  
01 800 964 77 26 (01 800 9 NISSAN).  
Connecting Bluetooth® audio:  
Connecting phone:  
NISSAN strongly recommends using a stereo mini  
plug cable when connecting your music device to the  
audio system. Music may not play properly when a  
monaural cable is used.  
To use this feature, a compatible smartphone must be  
connected via Bluetooth® or USB to the vehicle. For  
the Bluetooth® connecting procedure, see “Bluetooth®  
Hands-Free Phone System (Type C)” (P.4-51).  
AUX button:  
NOTE:  
.
.
.
For Apple iPhones, NissanConnect Apps  
REQUIRES the phone to be plugged in via  
USB.  
To switch to the AUX mode, push the AUX button until  
the AUX mode is selected while the ignition switch is  
placed in the “ON” or “ACC” position.  
JVH1010X  
For Vehicles without Navigation, Apple  
iPhones must be paired via Bluetooth® for  
NissanConnect Apps to function.  
To connect your Bluetooth® audio device to the  
vehicle, follow the procedure below:  
NissanConnect App smartphone integration  
This vehicle is equipped with Smartphone Integration  
technology. This allows many compatible Smartphone  
applications to be displayed and easily controlled  
through the audio display.  
For Android phones, NissanConnect Apps  
REQUIRES the phone to be paired via Blue-  
tooth®.  
1. Push the SETUP button.  
2. Select the “Telephone & Bluetooth” key.  
3. Select the “Pair New Device” key.  
Application download:  
NOTE:  
4. The system acknowledges the command and asks  
you to initiate connecting from the phone handset.  
The connecting procedure of the cellular phone  
varies according to each cellular phone model.  
See the Bluetooth® device Owner’s Manual for  
details.  
Once connected, the NissanConnect Mobile App will  
search your phone to determine which compatible  
applications are currently installed. The vehicle will  
then download the in-vehicle interface for each of  
these compatible applications. Once downloaded, the  
user can access many smartphone Applications  
through the vehicle audio screen. For more information  
on application availability visit the NissanConnect  
website.  
The registration of a compatible smartphone is  
required to use mobile applications or to access  
connected features of certain vehicle applica-  
tions.  
Registering with NissanConnect App:  
Bluetooth® audio player main operation:  
To use the Smartphone Integration feature, it is  
necessary for the user to register with NissanConnect.  
In order to register, visit the NissanConnect website for  
more information and to sign up. Once registered,  
download the NissanConnect Mobile App from your  
compatible phone’s application download source and  
To switch to the Bluetooth® audio mode, push the AUX  
button repeatedly until the Bluetooth® audio mode is  
displayed on the screen.  
The controls for the Bluetooth® audio are displayed on  
the screen.  
Heater and air conditioner, and audio system 4-39  
SEEK tuning (radio):  
STEERING WHEEL SWITCH FOR AUDIO  
CONTROL (if equipped)  
USB (Universal Serial Bus) CONNECTION  
PORT  
Push the tuning switch for more than 1.5 seconds to  
seek the next or previous radio station.  
APS (Automatic Program Search) FF, APS REW  
(CD):  
Push the tuning switch for less than 1.5 seconds to  
return to the beginning of the present program or skip  
to the next program. Push several times to skip back or  
skip through programs.  
CD CARE AND CLEANING  
SAA3641  
SAA3444  
1.  
2.  
3.  
SOURCE select switch  
Tuning switch  
The USB port is located on the lower part of the  
instrument panel.  
VOLUME control switch  
The illustration is for the Left-Hand Drive (LHD) model.  
For the Right-Hand Drive (RHD) model, the layout will  
be the opposite.  
The audio system can be operated using the controls  
on the steering wheel.  
Refer to your device manufacturer’s owner information  
regarding the proper use and care of the device.  
SOURCE select switch  
Push the SOURCE select switch to change the mode  
to available audio source.  
SAA0451  
WARNING:  
.
.
.
Handle a CD by its edges. Never touch the  
surface of the disc. Do not bend the disc.  
VOLUME control switch  
Push up or down the VOLUME control switch to  
increase or decrease the volume.  
Do not connect, disconnect or operate the USB  
device while driving. Doing so can be a distrac-  
tion. If distracted you could lose control of your  
vehicle and cause an accident or serious injury.  
Always place the discs in the storage case when  
they are not being used.  
To clean a disc, wipe the surface from the center  
to the outer edge using a clean, soft cloth. Do not  
wipe the disc using a circular motion.  
Tuning switch  
Memory change (radio):  
CAUTION:  
Push the tuning switch for less than 1.5 seconds to  
change the next or previous radio preset.  
Do not use a conventional record cleaner or  
alcohol intended for industrial use.  
.
Do not force the USB device into the USB  
port. Inserting the USB device tilted or  
upside- down into the port may damage  
the port. Make sure that the USB device is  
connected correctly into the USB port.  
.
A new disc may be rough on the inner and outer  
edges. Remove the rough edges by rubbing the  
inner and outer edges with the side of a pen or  
pencil as illustrated.  
4-40 Heater and air conditioner, and audio system  
CAR PHONE OR CB RADIO  
When installing a CB, ham radio or a car phone in your  
vehicle, be sure to observe the following cautions,  
otherwise the new equipment may adversely affect the  
Engine Control System and other electronic parts.  
.
.
Do not grab the USB port cover (if equipped)  
when pulling the USB device out of the port.  
This could damage the port and the cover.  
WARNING:  
Do not allow the cable or an external device  
connected to the AUX terminal to affect your  
driving.  
Do not leave the USB cable in a place where  
it can be pulled unintentionally. Pulling the  
cable may damage the port.  
CAUTION:  
NOTE:  
.
.
.
Keep the antenna as far away as possible  
from the Electronic Control Module.  
Depending on the external device, please  
note that the volume may be louder or  
quieter than that of the external device.  
AUX (auxiliary) INPUT JACK  
Keep the antenna wire at least 20 cm (8 in)  
away from the Engine Control harnesses. Do  
not route the antenna wire next to any  
harnesses.  
.
.
When the AUX contacts the plug of the  
connector cable, noise may be heard.  
The connected external device cannot be  
operated with the main audio system. The  
volume and sound quality can be adjusted.  
.
.
.
Adjust the antenna standing wave ratio as  
recommended by the manufacturer.  
Connect the ground wire from the radio  
chassis to the body.  
.
.
The song title in the external device cannot  
be displayed on the audio display.  
For the power source of the external device,  
use the special battery. The external device  
cannot be charged with the AUX terminal.  
Noise may be heard if the CD, radio etc. is  
operated while charging the battery with the  
power socket of the vehicle.  
For details, consult a NISSAN dealer.  
JVH0370X  
The illustration is for the Left-Hand Drive (LHD) model.  
For the Right-Hand Drive (RHD) model, the layout will  
be the opposite.  
The AUX input jack is located on the lower part of the  
instrument panel. The AUX input jack accepts any  
standard analog audio input such as from a portable  
cassette tape/CD player, MP3 player or laptop  
computer.  
Push the  
selected, to play  
button repeatedly until the AUX mode is  
compatible device when it is  
a
plugged into the AUX input jack.  
NISSAN strongly recommends using a stereo mini  
plug cable when connecting your music device to the  
audio system. Music may not play properly when a  
monaural cable is used.  
Heater and air conditioner, and audio system 4-41  

Related Topics

Heater and air conditioner, and audio system
Safety precautions Center multi-function control panel Vehicle information and settings Rear view monitor Ventilators Heater and air conditioner Servicing air conditioner Bluetooth Hands-Free Phone System Voice Recognition system

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot