2010-2019 Nissan Juke SUV Heater and air conditioner, and audio system -> Heater and air conditioner User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Heater and air conditioner, and audio system -> Heater and air conditioner for Your Nissan Juke SUV First Generation (2010-2019)

VENTILATORS  
HEATER AND AIR CONDITIONER  
OPERATING TIPS (for automatic air condi-  
tioner)  
CENTER VENTILATOR  
WARNING:  
.
.
The heater and air conditioner operate only  
when the engine is running.  
Never leave children or adults who would  
normally require the support of others alone  
in the vehicle. Pets should not be left alone  
either. They could unknowingly activate  
switches or controls and inadvertently be-  
come involved in a serious accident and  
injure themselves. On hot, sunny days,  
temperatures in  
a
closed vehicle could  
SAA3338  
quickly become high enough to cause se-  
vere or possibly fatal injuries to people or  
animals.  
SAA2368A  
Adjust the air flow direction of the ventilators by moving  
the center knob (up/down, left/right) until the desired  
position is achieved.  
.
.
Do not use the recirculation mode for long  
periods as it may cause the interior air to  
become stale and the windows to fog up.  
SIDE VENTILATORS  
Do not adjust the heating and air condition-  
ing controls while driving so that full atten-  
tion may be given to vehicle operation.  
The heater and air conditioner operate when the  
engine is running. The air blower will operate even if  
the engine is turned off and the ignition switch is in the  
“ON” position.  
SAA3431  
*: The layout illustrated is for the Left-Hand Drive  
(LHD) models. In the Right-Hand Drive (RHD) models,  
these components are located on the opposite side.  
NOTE:  
.
Odors from inside and outside the vehicle  
can build up in the air conditioner unit. Odor  
can enter the passenger compartment  
through the vents.  
SAA3126  
When the engine coolant temperature and outside air  
temperature are low, the air flow from the foot outlets  
may not operate. However, this is not a malfunction.  
After the coolant temperature warms up, the air flow  
from the foot outlets will operate normally.  
Open or close the vents, and adjust the air flow  
direction of ventilators as illustrated.  
.
When parking, set the heater and air condi-  
tioner controls to turn off air recirculation to  
allow fresh air into the passenger compart-  
ment. This should help reduce odors inside  
the vehicle.  
1
2
The sensors  
and  
, located on the instrument  
*
*
panel, help maintain a constant temperature. Do not  
put anything on or around the sensors.  
4-10 Heater and air conditioner, and audio system  
A/C (Air Conditioner) operation:  
MANUAL AIR CONDITIONER  
Push the “A/C” button to turn on or off the air  
conditioner. When the air conditioner is on, the “A/C”  
indicator light on the button illuminates.  
Temperature control:  
Turn the temperature control dial to set the desired  
temperature. Turn the dial between the middle and the  
right position to select the hot temperature. Turn the  
dial between the middle and the left position to select  
the cool temperature.  
Heater operation  
SAA3432  
Heating:  
1.  
Air intake lever (Outside air circulation “  
”
Air flow control:  
This mode is used to direct heated air to the foot  
outlets.  
/Air recirculation “  
Air flow control dial  
Fan speed control “  
”)  
Turn the air flow control dial to change the air flow  
mode.  
2.  
3.  
4.  
5.  
6.  
1. Move the air intake lever to the “  
normal heating.  
” position for  
” dial  
—
Air flows from the center and side  
ventilators.  
“A/C” (Air Conditioner) button  
Temperature control dial  
2. Turn the air flow control dial to the “  
” position.  
—
Air flows from the center and side  
ventilators and foot outlets.  
3. Turn the fan speed control “  
desired position.  
” dial to the  
Rear window defogger  
“Defogger switch” (P.2-28).)  
To turn off the heater and air conditioner, turn the fan  
“
”
button (See  
—
—
Air flows mainly from the foot outlets.  
4. Turn the temperature control dial to the desired  
position between the middle and the hot (right)  
position.  
Air flows from the defogger and foot  
outlets.  
speed control “  
” dial to the “OFF” (0) position.  
—
Air flows mainly from the defogger outlets.  
Controls  
Ventilation:  
Fan speed control:  
Outside air circulation:  
This mode directs outside air to the side and center  
ventilators.  
Turn the fan speed control “  
increase the fan speed.  
” dial clockwise to  
” dial counterclock-  
Move the air intake lever to the “  
flow is drawn from outside the vehicle.  
” position. The air  
1. Move the air intake lever to the “  
2. Turn the air flow control dial to the “  
” position.  
” position.  
Turn the fan speed control “  
Air recirculation:  
wise to decrease the fan speed.  
Move the air intake lever to the “  
flow is circulated inside the vehicle.  
” position. The air  
3. Turn the fan speed control “  
desired position.  
” dial to the  
4. Turn the temperature control dial to the desired  
position.  
Heater and air conditioner, and audio system 4-11  
Defrosting or defogging:  
Heating and defogging:  
Dehumidified heating:  
This mode directs the air to the defogger outlets to  
defrost/defog the windows.  
This mode heats the interior and defogs the windows.  
This mode is used to heat and dehumidify the air.  
1. Move the air intake lever to the “  
2. Turn the air flow control dial to the “  
” position.  
” position.  
1. Move the air intake lever to the “  
2. Turn the air flow control dial to the “  
” position.  
” position.  
1. Move the air intake lever to the “  
2. Turn the air flow control dial to the “  
” position.  
” position.  
3. Turn the fan speed control “  
desired position.  
” dial to the  
3. Turn the fan speed control “  
desired position.  
” dial to the  
3. Turn the fan speed control “  
desired position.  
” dial to the  
4. Turn the temperature control dial to the maximum  
hot (right) position.  
4. Push the “A/C” button on. (The “A/C” indicator  
light will illuminate.)  
4. Turn the temperature control dial to the desired  
position between the middle and the hot (right)  
position.  
5. Turn the temperature control dial to the desired  
position between the middle and the hot (right)  
position.  
Air conditioner operation  
The air conditioner system should be operated for  
approximately 10 minutes at least once a month. This  
helps prevent damage to the air conditioner system  
due to the lack of lubrication.  
.
To remove frost from the outside surface of the  
windshield quickly, turn the temperature control  
dial to the maximum hot position and the fan  
Dehumidified defogging:  
This mode is used to defog the windows and  
dehumidify the air.  
speed control “  
” dial to maximum position.  
Cooling:  
.
If it is difficult to defog the windshield, turn the  
“A/C” button on.  
1. Move the air intake lever to the “  
2. Turn the air flow control dial to the “  
” position.  
” position.  
This mode is used to cool and dehumidify the air.  
Bi-level heating:  
1. Move the air intake lever to the “  
2. Turn the air flow control dial to the “  
” position.  
” position.  
3. Turn the fan speed control “  
desired position.  
” dial to the  
This mode directs cool air from the side and center  
ventilators and warm air from the foot outlets. When  
the temperature control dial is turned to the maximum  
hot or cool position, the air between the ventilators and  
the foot outlets is the same temperature.  
3. Turn the fan speed control “  
desired position.  
” dial to the  
4. Push the “A/C” button on. (The “A/C” indicator  
light will illuminate.)  
4. Push the “A/C” button on. (The “A/C” indicator  
light will illuminate.)  
5. Turn the temperature control dial to the desired  
position.  
1. Move the air intake lever to the “  
2. Turn the air flow control dial to the “  
” position.  
” position.  
5. Turn the temperature control dial to the desired  
position between the middle and the cool (left)  
position.  
3. Turn the fan speed control “  
desired position.  
” dial to the  
A visible mist may be seen coming from the ventilators  
in hot, humid conditions as the air is cooled rapidly.  
This does not indicate a malfunction.  
4. Turn the temperature control dial to the desired  
position.  
4-12 Heater and air conditioner, and audio system  
AUTOMATIC AIR CONDITIONER (models with Integrated Control System)  
Selecting Climate mode  
SAA3339  
While the Climate mode is indicated on the display  
screen, the room temperature and fan speed, and  
automatic mode or manual mode, are indicated by the  
full screen. To indicate the climate mode, push the  
“CLIMATE” button.  
For details of the drive mode functions, see “Integrated  
control system” (P.5-15) or “Integrated control system”  
(P.2-18).  
Automatic operation (AUTO)  
The AUTO mode may be used year-round as the  
system automatically controls constant temperature, air  
flow distribution and fan speed after the desired  
temperature is set manually.  
SAA3335  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
“AUTO” button/Temperature control dial  
“OFF” button  
9.  
Air intake button (Outside air circulation  
”/Air recirculation “ ”)  
10. Rear window defogger  
“Defogger switch” (P.2-28).)  
To turn off the heater and air conditioner, push the  
“CLIMATE” button to change to the climate control  
mode, then push the “OFF” button.  
“
“
”
button (See  
“A/C” (Air Conditioner) button  
“CLIMATE” (Climate mode select) button  
Display screen  
Cooling and dehumidified heating:  
1. Push the “AUTO” button.  
Air flow control buttons  
2. Turn the temperature control dial to set the desired  
temperature.  
Fan speed control “  
Front defogger “  
” dial  
” button  
A visible mist may be seen coming from the ventilators  
in hot, humid conditions as the air is cooled rapidly.  
Heater and air conditioner, and audio system 4-13  
This does not indicate a malfunction.  
Outside air circulation:  
Manual operation  
Push the air intake button to draw the air flow from  
The manual mode can be used to control the heater  
and air conditioner to your desired settings.  
Heating (A/C off):  
outside the vehicle. (The indicator light on the “  
side will illuminate.)  
”
1. Push the “AUTO” button.  
To turn off the heater and air conditioner, push the  
“OFF” button.  
2. If the “A/C” indicator light illuminates, push the  
“A/C” button.  
Air recirculation:  
Push the air intake button to circulate the air flow inside  
.
While the “Drive Mode” is indicated on the screen,  
adjusting the amount of airflow and controlling the  
airflow direction are not possible. Push the  
“CLIMATE” button to change to the “Climate  
Control mode”.  
3. Turn the temperature control dial to set the desired  
temperature.  
the vehicle. (The indicator light on the “  
illuminate.)  
” side will  
.
Do not set the temperature lower than the outside  
air temperature. Doing so may cause the tem-  
perature to not be controlled properly.  
Automatic air intake control:  
Push the air intake button for approximately 2 seconds.  
The indicator lights (both air recirculation and outside  
air circulation sides) will blink twice, and then the  
intake air will be controlled automatically. The auto-  
matic control is set between the outside air circulation  
Fan speed control:  
.
If the windows fog up, use dehumidified heating  
instead of the A/C off heating.  
Turn the “  
” fan speed control dial clockwise (+) or  
counterclockwise (−) to manually control the fan  
speed.  
Dehumidified defrosting/defogging:  
1. Push the front defogger  
” indicator light will illuminate.)  
“
”
button. (The  
“
”
and air recirculation  
“
”
modes (the  
Push the “AUTO” button to change the fan speed to  
the automatic mode.  
“
indicator light of the side that is operating will  
illuminate).  
2. Turn the temperature control dial to set the desired  
temperature.  
Air flow control:  
Setting climate ECO  
When the Drive Mode is displayed, you can set  
CLIMATE ECO ON or OFF.  
Push the corresponding air flow control button to set  
the air outlet to the preferred mode.  
.
To remove frost from the outside surface of the  
windshield quickly, set the temperature to a high  
temperature and the fan speed to the maximum  
level.  
—
Air flows from the center and side  
ventilators.  
(See “ECO drive mode” (P.5-17).)  
—
Air flows from the center and side  
ventilators and foot outlets.  
.
.
After the windshield is cleared, push the front  
SERVICING AIR CONDITIONER  
defogger “  
” button again. (The indicator light  
will turn off.)  
—
—
Air flows mainly from the foot outlets  
WARNING:  
When the front defogger “  
” button is pushed,  
Air flows from the defogger outlets and  
foot outlets.  
The air conditioner system contains refrigerant  
under high pressure. To avoid personal injury,  
any air conditioner service should be done only  
by an experienced technician with the proper  
equipment.  
the air conditioner will automatically turn on to  
defog the windshield. The air recirculation mode  
will automatically turn off. The outside air circula-  
Temperature control:  
Turn the temperature control dial to set the desired  
temperature.  
tion mode “  
” will be selected to improve the  
defogging performance.  
The air conditioner system in your vehicle is charged  
with a refrigerant designed with the environment in  
mind.  
This refrigerant will not harm the earth’s ozone  
4-14 Heater and air conditioner, and audio system  

Related Topics

Heater and air conditioner, and audio system
Safety precautions Center multi-function control panel Vehicle information and settings Rear view monitor Ventilators Servicing air conditioner Audio system Bluetooth Hands-Free Phone System Voice Recognition system

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot