2010-2019 Nissan Juke SUV Instruments and controls User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Instruments and controls for Your Nissan Juke SUV First Generation (2010-2019)

2 Instruments and controls  
Cockpit ....................................................................................................... 2-2  
Left-Hand Drive (LHD) models ..................................................... 2-2  
Right-Hand Drive (RHD) models .................................................. 2-3  
Instrument panel ...................................................................................... 2-4  
Left-Hand Drive (LHD) models ..................................................... 2-4  
Right-Hand Drive (RHD) models .................................................. 2-5  
Meters and gauges ................................................................................. 2-6  
Speedometer ...................................................................................... 2-7  
Odometer ............................................................................................ 2-7  
Tachometer ......................................................................................... 2-7  
Engine coolant temperature gauge .............................................. 2-7  
Fuel gauge .......................................................................................... 2-7  
Vehicle information display ............................................................. 2-8  
Outside air temperature .................................................................. 2-8  
Instrument brightness control ........................................................ 2-8  
Headlight and turn signal switch ..................................................... 2-24  
Xenon headlights (if equipped) ............................................... 2-24  
Headlight switch .......................................................................... 2-24  
Headlight aiming control (if equipped) .................................. 2-25  
Turn signal switch ........................................................................ 2-26  
Fog light switch (if equipped) .......................................................... 2-26  
Front fog lights ............................................................................. 2-26  
Wiper and washer switch .................................................................. 2-27  
Windshield wiper and washer switch .................................... 2-27  
Rear window wiper and washer switch ................................. 2-28  
Defogger switch ................................................................................... 2-28  
Horn ........................................................................................................ 2-29  
Windows ................................................................................................ 2-29  
Power windows ............................................................................ 2-29  
Power outlet .......................................................................................... 2-31  
Storages ................................................................................................. 2-31  
Glove box ...................................................................................... 2-31  
Cup holders .................................................................................. 2-31  
Cargo floor box (if equipped) ................................................... 2-32  
Coat hook (if equipped) ............................................................ 2-32  
Cargo cover (if equipped) ......................................................... 2-32  
Sun visors .............................................................................................. 2-33  
Sunroof (if equipped) ......................................................................... 2-33  
Automatic sunroof ....................................................................... 2-33  
Interior lights ......................................................................................... 2-34  
Map lights ...................................................................................... 2-34  
Map light control switch ............................................................ 2-35  
Cargo room lights ....................................................................... 2-35  
>
Continuously Variable Transmission (CVT) position indicator  
(if equipped) ....................................................................................... 2-8  
Trip computer ..................................................................................... 2-9  
Engine oil information (if equipped) ............................................. 2-9  
Warning/indicator lights and audible reminders ........................... 2-11  
Checking bulbs .............................................................................. 2-12  
Warning lights ................................................................................. 2-12  
Indicator lights ................................................................................ 2-15  
Audible reminders .......................................................................... 2-17  
Integrated control system (if equipped) ......................................... 2-18  
Drive mode ...................................................................................... 2-18  
Setup function ................................................................................ 2-19  
Drive information ............................................................................ 2-22  
ECO information ............................................................................ 2-22  
COCKPIT  
8.  
9.  
Vehicle Dynamic Control (VDC) off switch*  
LEFT-HAND DRIVE (LHD) MODELS  
Tire Pressure Monitoring System (TPMS) reset  
switch*  
10. Tilting steering wheel lever (for Mexico and  
Korea)  
11. Tilting steering wheel lever (for the Middle East)  
12. Steering-wheel-mounted controls (left side)  
— Audio control*  
— Bluetooth® Hands-Free Phone System*  
(without navigation system)  
— Bluetooth® Hands-Free Phone System* (with  
navigation system)  
13. Ignition switch (models without Intelligent Key  
system)  
14. Steering-wheel-mounted controls (right side)*  
— Cruise control switches*  
15. Front cup holders  
*:  
if equipped  
JVC0718X  
1.  
2.  
Outside mirror remote control switch  
Headlight, fog light* and turn signal switch  
— Headlight  
— Driver’s supplemental front-impact air bag  
Wiper and washer switch  
4.  
5.  
Shift lever  
— Turn signal  
— Continuously Variable Transmission (CVT)  
— Manual Transmission (MT)  
Fuse box cover  
— Fog light*  
3.  
Steering wheel  
6.  
7.  
— Electric power steering system  
— Horn  
Headlight aiming control switch*  
2-2 Instruments and controls  
9.  
Tilting steering wheel lever  
RIGHT-HAND DRIVE (RHD) MODELS  
10. Ignition switch (models without Intelligent Key  
system)  
11. Vehicle Dynamic Control (VDC) off switch*  
12. Headlight aiming control switch*  
13. Fuse box cover  
*:  
if equipped  
JVC0719X  
1.  
Shift lever  
— Turn signal  
— Continuously Variable Transmission (CVT)  
Wiper and washer switch  
Steering wheel  
— Fog light*  
2.  
3.  
5.  
6.  
7.  
Outside mirror remote control switch  
Front cup holders  
— Electric power steering system  
— Horn  
Steering-wheel-mounted controls (left side)*  
— Audio control*  
— Driver’s supplemental front-impact air bag  
Headlight, fog light* and turn signal switch  
— Headlight  
— Bluetooth® Hands-Free Phone System*  
Steering-wheel-mounted controls (right side)*  
— Cruise control switches*  
4.  
8.  
Instruments and controls 2-3  
INSTRUMENT PANEL  
11. USB and AUX connector*  
— USB connection port*  
— Auxiliary input jack*  
12. Parking brake  
LEFT-HAND DRIVE (LHD) MODELS  
13. Heated seat switch*  
14. Power outlet  
15. Glove box  
*:  
if equipped  
**:  
See the separate Navigation System Owner’s  
Manual (if equipped).  
JVC0727X  
1.  
2.  
3.  
4.  
5.  
Meters and gauges  
5.  
Heater and air conditioner control* (models  
without Integrated Control System)  
Center ventilator  
— Defogger switch  
Audio system* or Navigation system**  
Hazard indicator flasher switch  
Integrated Control System*  
— Drive mode  
6.  
7.  
8.  
9.  
Passenger’s front-impact air bag  
Side ventilator  
Fuel filler lid release handle  
Hood release handle  
— Heater and air conditioner control  
— Defogger switch  
10. Push-button ignition switch (models with Intel-  
ligent Key system)  
2-4 Instruments and controls  
12. USB and AUX connector*  
— USB connection port*  
— Auxiliary input jack*  
RIGHT-HAND DRIVE (RHD) MODELS  
13. Push-button ignition switch (models with Intel-  
ligent Key system)  
14. Hood release handle  
15. Fuel filler lid release handle  
*:  
if equipped  
JVC0720X  
1.  
2.  
3.  
Side ventilator  
4.  
5.  
6.  
7.  
8.  
9.  
Hazard indicator flasher switch  
Audio system*  
Passenger’s front-impact air bag  
Integrated Control System*  
— Drive mode  
Center ventilator  
Meters and gauges  
Glove box  
— Heater and air conditioner control  
— Defogger switch  
Power outlet  
3.  
Heater and air conditioner* (models without  
Integrated Control System)  
10. Parking brake  
11. Heated seat switch*  
— Defogger switch  
Instruments and controls 2-5  
METERS AND GAUGES  
The needle indicators may move slightly after  
the ignition switch is placed in the “OFF” or  
“LOCK” position. This is not a malfunction.  
SIC4504  
Type A  
SIC4503  
SIC4738  
1.  
2.  
3.  
Tachometer  
5.  
6.  
7.  
8.  
Speedometer  
Type B  
Engine coolant temperature gauge  
Vehicle information display  
— Odometer/twin trip odometer  
— Trip computer  
Warning/indicator lights  
Instrument brightness control knob  
Continuously Variable Transmission (CVT) posi-  
tion indicator*  
9.  
*:  
RESET switch for trip odometer/Trip computer  
mode switch  
— Cruise control*  
— Outside air temperature  
— Engine oil information*  
Fuel gauge  
if equipped  
4.  
2-6 Instruments and controls  
Resetting trip odometer:  
the engine coolant temperature.  
SPEEDOMETER  
3
Push the reset switch  
*
for approximately 1 second  
to reset the trip odometer to zero.  
The engine coolant temperature is normal when the  
The speedometer indicates the vehicle speed (km/h or  
MPH).  
2
*
gauge is within the zone  
shown in the illustration.  
The engine coolant temperature will vary with the  
outside air temperature and driving conditions.  
TACHOMETER  
ODOMETER  
Odometer/Twin trip odometer  
CAUTION:  
.
If the gauge indicates engine coolant tem-  
perature near the hot end of the normal  
range, reduce vehicle speed to decrease  
temperature.  
.
.
If the gauge is over the normal range, stop  
the vehicle as soon as safely possible.  
If the engine is overheated, continued op-  
eration of the vehicle may seriously damage  
the engine. (See “If your vehicle overheats”  
(P.6-8) for immediate action required.)  
SIC4506  
The tachometer indicates the engine speed in revolu-  
tions per minute (rpm). Do not rev the engine into  
SIC4505  
The odometer/twin trip odometer is displayed when  
the ignition switch is in the “ON” position.  
1
the red zone  
.
*
FUEL GAUGE  
The red zone varies with models.  
1
The odometer  
displays the total distance the  
*
ENGINE COOLANT TEMPERATURE  
GAUGE  
vehicle has been driven.  
2
*
The twin trip odometer  
individual trips.  
displays the distance of  
Changing trip odometer display:  
3
Push the reset switch  
follows:  
to change the display as  
*
TRIP A ? TRIP B ? Trip computer mode ?TRIP A  
For trip computer information, see “Trip computer”  
(P.2-9).  
SIC4252  
1
The fuel gauge  
indicates the approximate fuel level  
*
in the tank when the ignition switch is in the “ON”  
position.  
SIC4123  
The gauge may move slightly during braking, turning,  
accelerating, or going up and down hills due to  
1
The engine coolant temperature gauge  
*
indicates  
Instruments and controls 2-7  
movement of fuel in the tank.  
The low fuel warning light  
When the ignition switch is placed in the “ON”  
position, the vehicle information display shows the  
following information:  
2
*
illuminates when  
the fuel level in the tank is getting low. Refuel as soon  
1.  
2.  
Outside air temperature  
as it is convenient, preferably before the gauge reads  
0.  
Continuously Variable Transmission (CVT) posi-  
tion indicator (if equipped)  
The arrow,  
, indicates that the fuel filler lid is  
3.  
4.  
Odometer/Instrument brightness control display  
located on the right side of the vehicle.  
Twin trip odometer/Trip computer/Cruise control  
display (if equipped)  
CAUTION:  
Engine oil information is also displayed on the vehicle  
information display when required (if equipped).  
Refuel before the gauge reads 0 (empty).  
SIC4256  
There is a small reserve of fuel in the tank when the fuel  
gauge reads 0 (empty).  
The instrument brightness control operates when the  
ignition switch is in the “ON” position.  
For the cruise control (if equipped), see “Cruise  
control” (P.5-19).  
A
Push the control knob  
to adjust the brightness of  
*
Malfunction Indicator Light (MIL)  
For Korea:  
OUTSIDE AIR TEMPERATURE  
The outside air temperature is displayed in 8C.  
B
the meter panel. The brightness indicator  
shown briefly in the vehicle information display when  
the control is pushed.  
will be  
*
If the Malfunction Indicator Light (MIL) illuminates while  
the engine is running, it may indicate that the fuel filler  
cap is loose or missing, or that the fuel level is low.  
Make sure that the fuel filler cap is installed and closed  
tightly, and that a sufficient amount of fuel remains in  
the fuel tank. (See “Malfunction Indicator Light (MI or  
MIL)” (P.2-16).)  
When the outside air temperature becomes 38C  
(378F) or lower, the outside air temperature display  
blinks to give a warning.  
When the brightness level reaches the maximum or  
minimum, a beep will sound.  
The display will stop blinking after 1 minute or when  
the outside air temperature becomes 48C (398F) or  
above.  
CONTINUOUSLY VARIABLE TRANSMIS-  
SION (CVT) POSITION INDICATOR (if  
equipped)  
INSTRUMENT BRIGHTNESS CONTROL  
The Continuously Variable Transmission (CVT) position  
indicator indicates the shift lever position when the  
ignition switch is in the “ON” position.  
VEHICLE INFORMATION DISPLAY  
SIC4517  
SIC4516  
2-8 Instruments and controls  
when the fuel level is low, the dte mode is automatically  
selected and the digits and the low fuel warning light  
blink in order to draw the driver’s attention. Push  
A
TRIP COMPUTER  
ENGINE OIL INFORMATION (if equipped)  
the trip computer mode switch  
to return to the  
*
mode that was selected before the warning occurred.  
When the fuel level drops even lower, the dte display  
will change to “----”.  
.
If the amount of fuel added is small, the  
display just before the ignition switch is  
turned off may continue to be displayed.  
.
When driving uphill or rounding curves, the  
fuel in the tank shifts, which may momenta-  
rily change the display.  
SIC4518  
SIC3396  
The switch for the trip computer is located on the  
meter panel.  
When the ignition switch is in the “ON” position,  
engine oil information is displayed on the vehicle  
information display in the following order:  
Average fuel consumption (l/100 km or mpg)  
The average fuel consumption mode shows the  
average fuel consumption since the last reset. Reset-  
ting is done by pushing the trip computer setting  
A
When the ignition switch is placed in the “ON”  
position, modes of the trip computer can be selected  
Distance to oil change (with a wrench symbol) ? Oil  
level indication (“Oil Good” or “Oil Lo”)  
A
by pushing the trip computer mode switch  
.
*
switch  
for longer than 1 second.  
*
A
A
Each time the trip computer mode switch  
pushed, the display will change as follows:  
is  
Push the trip computer mode switch  
for  
5
*
*
The display is updated every 30 seconds. At about the  
first 500 m (1/3 miles) after a reset, the display shows  
“----”.  
seconds while the oil level indication is displayed.  
When the “Oil Good” is indicated, a detail of the oil  
(TRIP A ? TRIP B) ? Current fuel consumption ?  
Distance to empty (dte) ? Average fuel consumption  
? Elapsed time (? TRIP A)  
5
1
level (  
-
) appears as illustrated.  
* *  
Elapsed time (h:m:s)  
CAUTION:  
The elapsed time mode shows the time since the last  
reset. The displayed time can be reset by pushing the  
Current fuel consumption  
The current fuel consumption mode shows the current  
fuel consumption.  
The oil level should be checked regularly.  
Operating with an insufficient amount of oil  
can damage the engine and such damage is not  
covered by the warranty.  
A
*
trip computer mode switch  
second.  
for longer than 1  
Distance to empty (dte — km or mls)  
Resetting displays  
When the average fuel consumption, elapsed time or  
TRIP B is displayed, push the trip computer mode  
The distance to empty (dte) mode provides you with an  
estimation of the distance that can be driven before  
refueling. The dte is constantly being calculated, based  
on the amount of fuel in the fuel tank and the actual fuel  
consumption.  
(See “Engine oil” (P.8-8) for checking the oil level.)  
A
switch  
for longer than 3 seconds. The display of  
*
average fuel consumption, elapsed time and trip  
odometer (TRIP B only) will be reset at the same time.  
The display is updated every 30 seconds.  
The dte mode includes a low range warning feature:  
Instruments and controls 2-9  
2. While the display is flashing, push the trip  
Setting distance to oil change  
The distance to oil change interval can be adjusted or  
disabled using the trip computer mode switch  
A
*
computer mode switch  
adjusting mode.  
again to enter the  
A
*
.
A
*
3. Push the trip computer mode switch  
interval reads 0.  
until the  
Refer to the separate maintenance booklet for the  
appropriate distance to oil change interval.  
If no further action is taken, the display will switch to  
the oil level indication and the oil change reminder is  
cancelled.  
To adjust oil change interval:  
A
1. Push and hold the trip computer mode switch  
*
for more than 3 seconds while the wrench symbol  
and distance to oil change information are  
displayed.  
No wrench symbol or distance will be displayed when  
the ignition switch is placed in the “ON” position. To  
reactivate the reminder, set the distance to oil change  
interval to a value above zero (0).  
If adjusting the distance from zero (0): Push and  
hold the trip computer mode switch  
than 3 seconds within 5 seconds of placing the  
ignition switch in the “ON” position.  
A
*
for more  
The wrench symbol and the distance will start  
flashing.  
2. While the display is flashing, push the trip  
A
*
computer mode switch  
adjusting mode.  
again to enter the  
If adjusting the distance from zero (0): Push the  
A
trip computer mode switch  
.
The default  
*
distance to oil change will be restored.  
A
3. Push the trip computer mode switch  
to  
*
increase the interval. Each push increases the  
interval by 1,000 km (500 miles).  
If no further action is taken, the display will switch to  
the oil level indication and the new interval will be set.  
To cancel oil change reminder:  
A
1. Push and hold the trip computer mode switch  
*
for more than 3 seconds while the wrench symbol  
and distance to oil change information are  
displayed.  
The wrench symbol and the distance will start  
flashing.  
2-10 Instruments and controls  
WARNING/INDICATOR LIGHTS AND  
AUDIBLE REMINDERS  
Anti-lock Braking System (ABS) warning  
light  
P position selecting warning light (if  
equipped)  
Front passenger air bag status light (if  
equipped)  
Brake warning light  
Seat belt warning light  
High beam indicator light  
Speed [120 km/h (75 MPH)] warning light (if  
equipped)  
Charge warning light  
Malfunction Indicator Light (MI or MIL)  
Supplemental Restraint System (SRS) air  
bag warning light  
Door open warning light  
Vehicle Dynamic Control (VDC) warning light  
(if equipped)  
Electric power steering warning light  
Engine oil pressure warning light  
Overdrive off indicator light (if equipped)  
Security indicator light  
Continuously Variable Transmission (CVT)  
indicator light (if equipped)  
Intelligent Key system warning light (if  
equipped)  
Cruise indicator light (if equipped)  
Small light indicator light  
Engine start operation indicator light (if  
equipped)  
Low fuel warning light  
Turn signals/hazard indicator lights  
Vehicle Dynamic Control (VDC) off indicator  
light (if equipped)  
Low tire pressure warning light (if equipped)  
Front fog lights indicator light (if equipped)  
Instruments and controls 2-11  
stop the vehicle safely as soon as possible. Stop the  
engine and check the brake fluid level. If the brake fluid  
level is at the minimum mark, add brake fluid as  
necessary. (See “Brake and clutch fluid” (P.8-12).)  
CHECKING BULBS  
Brake warning light  
With all doors closed, apply the parking brake, fasten  
the seat belts and place the ignition switch in the “ON”  
position without starting the engine. If equipped, the  
WARNING:  
If the brake fluid level is sufficient, have the brake  
system checked by a NISSAN dealer promptly.  
following lights will illuminate:  
,
,
,
,
.
If the brake fluid level is below the minimum  
mark on the brake fluid reservoir, do not  
drive the vehicle until the brake system has  
been checked by a NISSAN dealer.  
,
,
.
If equipped, the following lights will illuminate briefly  
and then turn off: ,  
Anti-lock Braking System (ABS) warning indi-  
cator:  
,
,
,
,
,
,
.
.
.
Even if you judge it to be safe, have your  
vehicle towed because driving it could be  
dangerous.  
When the parking brake is released and the brake fluid  
level is sufficient, if both the brake warning light and the  
Anti-lock Braking System (ABS) warning light illumi-  
nate, it may indicate the ABS is not functioning  
properly. Have the brake system checked, and if  
necessary repaired, by a NISSAN dealer promptly.  
(See “Anti-lock Braking System (ABS) warning light”  
(P.2-12).)  
If any lights fail to illuminate, it may indicate a burned-  
out bulb or an open circuit in the electrical system.  
Have the system checked, and if necessary repaired,  
by a NISSAN dealer promptly.  
Depressing the brake pedal without the  
engine running and/or with  
a
low brake  
fluid level could increase the stopping dis-  
tance and require greater pedal travel dis-  
tance and effort.  
WARNING LIGHTS  
Anti-lock Braking System (ABS)  
warning light  
The brake warning light indicates the parking brake  
system operation, a low brake fluid level of the brake  
system and an Anti-lock Braking System (ABS)  
malfunction.  
Charge warning light  
When the ignition switch is in the “ON” position, the  
Anti-lock Braking System (ABS) warning light illumi-  
nates and then turns off. This indicates the ABS is  
operational.  
When the ignition switch is in the “ON” position, the  
charge warning light illuminates. After starting the  
engine, the charge warning light turns off. This  
indicates the charging system is operational.  
Parking brake warning indicator:  
When the ignition switch is placed in the “ON”  
position, the brake warning light illuminates. When  
the engine is started and the parking brake is released,  
the brake warning light turns off.  
If the ABS warning light illuminates while the engine is  
running, or while driving, it may indicate the ABS is not  
functioning properly. Have the system checked by a  
NISSAN dealer promptly.  
If the charge warning light illuminates while the engine  
is running, or while driving, it may indicate the charging  
system is not functioning properly and may need  
servicing.  
If the parking brake is not fully released, the brake  
warning light remains on. Be sure that the brake  
warning light has turned off before driving. (See  
“Parking brake” (P.3-20).)  
If an ABS malfunction occurs, the anti-lock function is  
turned off. The brake system then operates normally,  
but without anti-lock assistance. (See “Brake system”  
(P.5-24).)  
When the charge warning light illuminates while  
driving, stop the vehicle safely as soon as possible.  
Stop the engine and check the alternator belt. If the  
alternator belt is loose, broken or missing, the charging  
system needs repair. (See “Drive belt” (P.8-10).)  
Low brake fluid warning indicator:  
If the brake warning light illuminates while the engine is  
running, or while driving, and the parking brake is  
released, it may indicate the brake fluid level is low.  
If the alternator belt appears to be functioning correctly  
but the charge warning light remains illuminated, have  
the charging system checked by a NISSAN dealer  
promptly.  
When the brake warning light illuminates while driving,  
2-12 Instruments and controls  
.
.
The light blinks in green when the Intelligent Key  
battery is running out of power. Replace the  
battery with a new one. (See “Battery” (P.8-15).)  
CAUTION:  
Engine oil pressure warning light  
Do not continue driving if the alternator belt is  
loose, broken or missing.  
When the ignition switch is in the “ON” position, the  
engine oil pressure warning light illuminates. After  
starting the engine, the engine oil pressure warning  
light turns off. This indicates that the oil pressure  
sensors in the engine are operational.  
The light illuminates in yellow when it warns of a  
malfunction with the electrical steering lock  
system (if equipped) or the Intelligent Key system.  
Door open warning light  
If the warning light illuminates in yellow while the  
engine is stopped, it may be impossible to free the  
steering lock (if equipped) or to start the engine. If the  
light comes on while the engine is running, you can  
drive the vehicle. However in these cases, contact a  
NISSAN dealer for repair as soon as possible.  
When the ignition switch is in the “ON” position, the  
door open warning light illuminates if any of the doors  
are open or not closed securely.  
If the engine oil pressure warning light illuminates while  
the engine is running, it may indicate that the engine oil  
pressure is low.  
Stop the vehicle safely as soon as possible. Stop the  
engine immediately and call a NISSAN dealer.  
Electric power steering warning light  
When the ignition switch is in the “ON” position, the  
electric power steering warning light illuminates. After  
starting the engine, the electric power steering warning  
light turns off. This indicates the electric power  
steering system is operational.  
Low fuel warning light  
CAUTION:  
The low fuel warning light illuminates when the fuel  
level in the tank is getting low. Refuel as soon as it is  
convenient, preferably before the fuel gauge reaches 0  
(empty).  
.
.
Running the engine with the engine oil  
pressure warning light illuminated could  
cause serious damage to the engine.  
If the electric power steering warning light illuminates  
while the engine is running, it may indicate the electric  
power steering system is not functioning properly and  
may need servicing. Have the electric power steering  
system checked by a NISSAN dealer.  
The engine oil pressure warning light is not  
designed to indicate a low oil level. The oil  
level should be checked using the dipstick.  
(See “Engine oil” (P.8-8).)  
There will be a small reserve of fuel remaining in  
the tank when the fuel gauge reaches 0 (empty).  
Low tire pressure warning light (if  
equipped)  
When the electric power steering warning light  
illuminates with the engine running, the power assist  
to the steering will cease operation but you will still  
have control of the vehicle. At this time, greater  
steering efforts are required to operate the steering  
wheel, especially in sharp turns and at low speeds.  
Intelligent Key system warning light (if  
equipped)  
When the ignition switch is in the “ON” position, the  
low tire pressure warning light illuminates and then  
turns off. This indicates that the low tire pressure  
warning system is operational.  
After the ignition switch is placed in the “ON” position,  
this light comes on for about 2 seconds and then turns  
off.  
This light illuminates if there is low tire pressure or a tire  
pressure warning system malfunction.  
(See “Electric power steering system” (P.5-23).)  
This light illuminates or blinks as follows:  
.
The light blinks in yellow when the door is closed  
with the Intelligent Key left outside the vehicle and  
the ignition switch in the “ACC” or “ON” position.  
Make sure that the Intelligent Key is inside the  
vehicle.  
The Tire Pressure Monitoring System (TPMS) monitors  
the tire pressure of all tires except the spare.  
Instruments and controls 2-13  
Low tire pressure warning:  
TPMS malfunction:  
.
.
When a spare tire is mounted or a wheel is  
replaced, the TPMS will not function and the  
low tire pressure warning light will flash for  
approximately 1 minute. The light will re-  
If the vehicle is being driven with low tire pressure, the  
warning light will illuminate.  
If the TPMS is not functioning properly, the low tire  
pressure warning light will flash for approximately 1  
minute when the ignition switch is pushed ON. The  
light will remain on after the 1 minute. Have the system  
checked by a NISSAN dealer.  
When the low tire pressure warning light illuminates,  
you should stop and adjust the tire pressure to the  
recommended COLD tire pressure shown on the tire  
placard. Use a tire pressure gauge to check the tire  
pressure.  
main on after  
1
minute. Contact your  
NISSAN dealer as soon as possible for tire  
replacement and/or system resetting.  
For additional information, see “Tire Pressure Monitor-  
ing System (TPMS)” (P.5-3).  
Replacing tires with those not originally  
specified by NISSAN could affect the proper  
operation of the TPMS.  
The low tire pressure warning light may not auto-  
matically turn off when the tire pressure is adjusted.  
After the tire is inflated to the recommended pressure,  
reset the tire pressures registered in your vehicle and  
then drive the vehicle at speeds above 25 km/h (16  
MPH).  
WARNING:  
.
.
If the light does not illuminate with the  
ignition switch pushed ON, have the vehicle  
checked by a NISSAN dealer as soon as  
possible.  
CAUTION:  
.
.
.
The TPMS is not a substitute for the regular  
tire pressure check. Be sure to check the tire  
pressure regularly.  
These operations are required to activate the TPMS  
and turn off the low tire pressure warning light.  
If the light illuminates while driving, avoid  
sudden steering maneuvers or abrupt brak-  
ing, reduce vehicle speed, pull off the road to  
a safe location and stop the vehicle as soon  
as possible. Driving with under-inflated tires  
may permanently damage the tires and  
increase the likelihood of tire failure. Ser-  
ious vehicle damage could occur and may  
lead to an accident and could result in  
serious personal injury. Check the tire pres-  
sure for all four tires. Adjust the tire pressure  
to the recommended COLD tire pressure  
shown on the tire placard to turn the low tire  
pressure warning light OFF. If you have a flat  
tire, replace it with a spare tire as soon as  
possible.  
If the vehicle is being driven at speeds of  
less than 25 km/h (16 MPH), the TPMS may  
not operate correctly.  
TPMS resetting must be also performed after a tire or a  
wheel is replaced, or the tires are rotated.  
Be sure to correctly install the specified size  
of tires to all four wheels.  
Depending on a change in the outside temperature,  
the low tire pressure warning light may illuminate even  
if the tire pressure has been adjusted properly. Adjust  
the tire pressure to the recommended COLD tire  
pressure again when the tires are cold, and reset the  
TPMS.  
P position selecting warning light (if  
equipped)  
The warning light blinks in red when the ignition switch  
is pushed to stop the engine with the shift lever in any  
position except the “P” (Park) position.  
If the low tire pressure warning light still continues to  
illuminate after the resetting operation, it may indicate  
that the TPMS is not functioning properly. Have the  
system checked by a NISSAN dealer.  
If this warning appears, move the shift lever to the “P”  
(Park) position or push the ignition switch to the “ON”  
position.  
For additional information, see “Tire Pressure Monitor-  
ing System (TPMS)” (P.5-3),“Tire Pressure Monitoring  
System (TPMS)” (P.6-2).  
.
After adjusting the tire pressure, be sure to  
reset the TPMS. Unless the resetting is  
performed, the TPMS will not warn of the  
low tire pressure.  
An inside warning chime will also sound.  
See “Intelligent Key system” (P.3-6).  
2-14 Instruments and controls  
system is not functioning properly and may need  
servicing. Have the system checked, and if necessary  
repaired, by a NISSAN dealer promptly. (See “Vehicle  
Dynamic Control (VDC) system” (P.5-18).)  
Seat belt warning light  
Supplemental Restraint System (SRS)  
air bag warning light  
Except for Korea:  
When the ignition switch is in the “ON” position, the  
Supplemental Restraint System (SRS) air bag warning  
light illuminates for about 7 seconds and then turns off.  
This indicates the SRS air bag system is operational.  
When the ignition switch is in the “ON” position, the  
seat belt warning light illuminates. The light will  
continue to illuminate until the driver’s seat belt is  
fastened.  
INDICATOR LIGHTS  
Continuously variable transmission  
(CVT) indicator light (if equipped)  
If any of the following conditions occur, the SRS air  
bag system and pre-tensioner seat belt need servicing.  
Have the system checked, and if necessary repaired,  
by a NISSAN dealer promptly.  
When the vehicle speed exceeds 15 km/h (10 MPH),  
the chime will sound unless the driver’s seat belt is  
securely fastened. The chime will continue to sound for  
about 90 seconds until the seat belt is fastened. (See  
“Seat belts” (P.1-7).)  
When the ignition switch is in the "ON" position, the  
Continuously Variable Transmission (CVT) indicator  
light illuminates and then turns off.  
.
.
.
The SRS air bag warning light remains illuminated  
after about 7 seconds.  
For Korea:  
Cruise indicator light (if equipped)  
The SRS air bag warning light flashes intermit-  
tently.  
When the ignition switch is in the “ON” position, the  
seat belt warning light illuminates. The light will  
continue to illuminate until the front seat belt is  
fastened.  
The cruise indicator light indicates the activation of the  
cruise control system.  
The SRS air bag warning light does not come on  
at all.  
Cruise main switch indicator:  
Unless checked and repaired, the SRS air bag system  
and/or pre-tensioner seat belt may not function  
properly. (See “Supplemental Restraint System  
(SRS)” (P.1-24).)  
For approximately 5 seconds after the ignition switch is  
in the “ON” position, the system does not activate the  
warning light for the front passenger.  
When the cruise control main switch is turned on, the  
indicator light will illuminate, indicating the cruise  
control system is in the standby mode. (See “Cruise  
control” (P.5-19).)  
When the vehicle speed exceeds 15 km/h (10 MPH),  
the light will blink and the chime will sound unless the  
front seat belt is securely fastened. The chime will  
continue to sound for about 90 seconds until the seat  
belt is fastened. (See “Seat belts” (P.1-7).)  
Cruise malfunction:  
Vehicle Dynamic Control (VDC) warn-  
ing light (if equipped)  
If the cruise indicator light blinks while the engine is  
running, it may indicate the cruise control system is not  
functioning properly. Have the system checked by a  
NISSAN dealer. (See “Cruise control” (P.5-19).)  
When the ignition switch is in the “ON” position, the  
VDC warning light illuminates and then turns off. This  
indicates the Vehicle Dynamic Control (VDC) system is  
operational.  
Speed [120 km/h (75 MPH)] warning  
light (if equipped)  
Engine start operation indicator light (if  
equipped)  
The VDC warning light blinks when the VDC system is  
operating.  
This light blinks when the vehicle speed goes over  
approximately 120 km/h (75 MPH). Be sure to observe  
the speed limit in the area where you are driving.  
This light appears when the shift lever is in the “P”  
(Park) position (Continuously Variable Transmission  
models) or “N” (Neutral) position (Manual Transmission  
models). This light means that the engine will start by  
pushing the ignition switch with the brake pedal (CVT  
When the warning light blinks while driving, the driving  
condition is slippery and the vehicle’s traction limit is  
about to be exceeded.  
If the VDC warning light illuminates while the engine is  
running or while driving, it may indicate the VDC  
Instruments and controls 2-15  
models) or the clutch pedal (MT models) depressed.  
You can start the engine directly in any position.  
reduced fuel economy, and damage to the  
engine control system and/or CVT system,  
which may affect the vehicle’s warranty  
coverage.  
For Korea:  
When the ignition switch is in the “ON” position,  
sometimes the MIL may illuminate for 20 seconds and  
then blink for 10 seconds, without the engine running.  
This is due to a function of checking the engine control  
system, and it is not a malfunction. After a few normal  
drives, this function will not occur and the MIL stays  
illuminated with the ignition switch in the “ON”  
position.  
Front fog lights indicator light (if  
equipped)  
.
Incorrect setting of the engine control sys-  
tem may lead to non-compliance of local  
and national emission laws and regulations.  
The front fog lights indicator light illuminates when the  
front fog lights are on. (See “Fog light switch” (P.2-  
26).)  
When the ignition switch is in the “ON” position, the  
Malfunction Indicator Light (MIL) illuminates. After  
starting the engine, the MIL turns off. This indicates  
that the engine control system and/or CVT system is  
operational.  
If the MIL illuminates while the engine is running, it may  
indicate that the fuel filler cap is loose or missing, or  
that the fuel level is low. Make sure that the fuel filler  
cap is installed and closed tightly, and that a sufficient  
amount of fuel remains in the fuel tank. After a few  
driving trips, the MIL should turn off. If the MIL  
continues to be illuminated, it may indicate that the  
engine control system is not functioning properly and  
may need servicing. Have the vehicle checked, and if  
necessary repaired, by a NISSAN dealer promptly.  
Front passenger air bag status light (if  
equipped)  
The front passenger air bag status light located on the  
instrument panel will illuminate and the front passenger  
air bag will be OFF depending on how the front  
passenger seat is being used.  
For Mexico and Thailand:  
If the MIL illuminates while the engine is running, it may  
indicate that the engine control system is not  
functioning properly and may need servicing. Have  
the vehicle checked, and if necessary repaired, by a  
NISSAN dealer promptly.  
For front passenger air bag status light operation, see  
“Supplemental front-impact air bag system (Advanced  
Air Bag System) (for Korea)” (P.1-30).  
If the MIL blinks while the engine is running, it may  
indicate a potential malfunction in the emission control  
system. In this case, the emission control system may  
not function properly and may need servicing. Have the  
system checked, and if necessary repaired, by  
NISSAN dealer promptly.  
If the MIL blinks while the engine is running, it may  
indicate a potential malfunction in the emission control  
system. In this case, the emission control system may  
not function properly and may need servicing. Have the  
High beam indicator light  
The high beam indicator light illuminates when the  
headlight high beam is on. The indicator turns off when  
the low beam is selected. (See “Headlight and turn  
signal switch” (P.2-24).)  
a
system checked, and if necessary repaired, by  
NISSAN dealer promptly.  
a
Precautions:  
Precautions:  
To reduce or avoid possible damage to the engine  
control system when the MIL blinks:  
To reduce or avoid possible damage to the engine  
control system when the MIL blinks:  
Malfunction Indicator Light (MI or  
MIL)  
.
.
.
.
Avoid driving at speeds above 70 km/h (43 MPH).  
Avoid sudden acceleration or deceleration.  
Avoid going up steep uphill grades.  
.
.
.
.
Avoid driving at speeds above 70 km/h (43 MPH).  
Avoid sudden acceleration or deceleration.  
Avoid going up steep uphill grades.  
CAUTION:  
Avoid carrying or towing unnecessary loads.  
Avoid carrying or towing unnecessary loads.  
.
Continuing vehicle operation without proper  
servicing of the engine control system and/  
or Continuously Variable Transmission (CVT)  
system could lead to poor driveability,  
2-16 Instruments and controls  
Except for Mexico, Thailand and Korea:  
Intelligent Key buzzer (if equipped)  
The Intelligent Key buzzer sounds if any one of the  
following improper operations is found.  
Turn signals/hazard indicator lights  
If the MIL illuminates while the engine is running, it may  
indicate that the engine control system is not  
functioning properly and may need servicing. Have  
the vehicle checked, and if necessary repaired, by a  
NISSAN dealer promptly.  
The turn signals/hazard indicator lights blink when the  
turn signal switch or hazard indicator flasher switch is  
turned on. (See “Headlight and turn signal switch”  
(P.2-24) or “Hazard indicator flasher switch” (P.6-2).)  
.
.
.
The ignition switch is not returned to the “LOCK”  
position when locking the doors.  
The Intelligent Key is left inside the vehicle when  
locking the doors.  
Overdrive off indicator light (if  
equipped)  
Vehicle Dynamic Control (VDC) off  
indicator light (if equipped)  
Any doors are not closed securely when locking  
the doors.  
When the buzzer sounds, be sure to check both the  
vehicle and the Intelligent Key. (See “Intelligent Key  
system” (P.3-6).)  
The overdrive off indicator light illuminates when the  
Overdrive is turned “OFF”. (See “Driving with Con-  
tinuously Variable Transmission (CVT)” (P.5-11) for the  
use of the overdrive off switch.)  
When the ignition switch is in the “ON” position, the  
Vehicle Dynamic Control (VDC) off indicator light  
illuminates and then turns off.  
The VDC off indicator light illuminates when the VDC  
off switch is pushed to the “OFF” position.  
Key reminder chime  
The key reminder chime will sound if any of the  
following operations are detected:  
Security indicator light  
When the VDC off switch is pushed to the “OFF”  
position, the VDC system is turned off. (See “Vehicle  
Dynamic Control (VDC) system” (P.5-18).)  
The security indicator light blinks when the ignition  
switch is in the “LOCK”, “OFF” or “ACC” position. This  
function indicates the security system equipped on the  
vehicle is operational.  
Models with Intelligent Key system:  
A chime will sound if the driver side door is opened  
while the ignition switch is placed in the ACC position.  
AUDIBLE REMINDERS  
Brake pad wear warning  
Models without Intelligent Key system:  
If the security system is malfunctioning, this light will  
remain on while the ignition switch is in the “ON”  
position. (See “Security system” (P.3-14) for additional  
information.)  
The key reminder chime sounds if the driver’s side door  
is opened while the key is left in the ignition switch and  
the ignition switch is in the ACC, OFF or LOCK  
position. Remove the key and take it with you when  
leaving the vehicle.  
The disc brake pads have audible wear warnings.  
When a brake pad requires replacement, it will make a  
high pitched scraping sound when the vehicle is in  
motion. This scraping sound will first occur only when  
the brake pedal is depressed. After more wear of the  
brake pad, the sound will always be heard even if the  
brake pedal is not depressed. Have the brakes  
checked as soon as possible if the wear warning  
sound is heard.  
Small light indicator light  
Light reminder chime  
The small light indicator light illuminates when the front  
clearance lights, instrument panel lights, rear combina-  
tion lights and license plate lights are on. The indicator  
The light reminder chime will sound if the driver’s side  
door is opened and the following operations are  
detected:  
light turns off when the  
is turned off.  
Have the system checked, and if necessary repaired,  
by a NISSAN dealer promptly. (See “Brakes” (P.8-  
11).)  
.
The headlight switch is in either the  
or  
position, and the ignition switch is in the “ACC”,  
“OFF” or “LOCK” position.  
Instruments and controls 2-17  
INTEGRATED CONTROL SYSTEM (if  
equipped)  
The Integrated Control System is located below the  
audio system. Two Integrated Control System modes  
can be selected: Drive mode and Climate Control  
mode.  
.
The chime will also sound for 2 seconds when the  
ignition switch is placed in the “ACC”, “OFF” or  
“LOCK” position while the fog lights (if equipped)  
are on with the headlight switch in the “AUTO”  
position (if equipped).  
Depending on which Integrated Control System mode  
is selected (Drive mode or Climate Control mode), the  
screen display and some button functions will change.  
Be sure to turn the headlight switch to the “OFF” or  
“AUTO” position (if equipped) and the fog light (if  
equipped) switch to the “OFF” position when you leave  
the vehicle.  
.
.
Drive mode  
In the Drive mode, three types of driving modes  
can be selected: NORMAL, SPORT and ECO.  
See “Integrated control system” (P.5-15). In  
addition, while in the Drive mode, SETUP, Drive  
information and ECO information can be displayed  
and adjusted. See “Integrated control system”  
(P.5-15).  
Parking brake reminder  
The chime will sound if the vehicle is driven at more  
than 7 km/h (4 MPH) with the parking brake applied.  
Stop the vehicle and release the parking brake.  
Climate Control mode  
In the Climate Control mode, the climate control  
can be set and adjusted. See “Automatic air  
conditioner (models with Integrated Control Sys-  
tem)” (P.4-13).  
DRIVE MODE  
When the Drive mode select button is pressed, the  
display and buttons appear as shown.  
2-18 Instruments and controls  
.
.
.
Selective Door Unlock (if equipped)  
Auto Headlight Sensitivity (if equipped)  
CLIMATE ECO  
NOTE:  
.
The SETUP function cannot be adjusted  
while driving. If you try to adjust the SETUP  
function while driving, a blank screen will be  
displayed.  
.
When the battery is disconnected, the SET-  
UP memory is erased and reverts to the  
default settings. If necessary, reset the  
SETUP memory after reconnecting the bat-  
tery.  
.
When in the Drive Mode, Display Brightness  
and Button Brightness can be set to the  
daytime mode or nighttime mode by press-  
ing the SETUP button for more than  
second (if equipped).  
1
Setting Display Brightness or Button Bright-  
ness  
SIC4623  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
9.  
Drive mode select button  
SETUP button  
SETUP FUNCTION  
While in the Drive Mode, the following items can be set  
up by pressing the SETUP button.  
NORMAL drive mode button  
SPORT drive mode button  
ECO drive mode button  
Display screen  
.
.
.
.
.
.
Display Brightness  
Button Brightness  
Clock Time Setting  
Select Language  
Select Units  
SIC4617  
Drive information button  
ECO information button  
ENTER button/Selection dial  
1. Press the Drive Mode Select button.  
2. Press the SETUP button.  
Auto Interior Illumination  
Instruments and controls 2-19  
3. Turn the Selection dial to “Display Brightness” or  
“Button Brightness” then press the Enter button.  
6. Turn the Selection dial to select the minutes, then  
press the Enter button to apply the selection.  
The item selected with the selection dial will  
change color.  
Select Language  
SIC4558  
1. Press the Drive Mode Select button.  
2. Press the SETUP button.  
SIC4560  
3. Turn the Selection dial to “Clock Time Setting”,  
then press the Enter button.  
SIC4557  
1. Press the Drive Mode Select button.  
2. Press the SETUP button.  
4. Turn the Selection dial to + to increase brightness  
or to − to decrease brightness, then press the  
Enter button to apply the selection.  
The item selected with the selection dial will  
change color.  
3. Turn the Selection dial to “Select Language”, then  
press the Enter button.  
Display Brightness and Button Brightness can be  
manually adjusted during the day (when the headlight  
switch is off) or at night (when the headlight switch is  
on).  
The item selected with the selection dial will  
change color.  
When the bar is at the maximum brightness level, the  
brightness level is the same as the daytime level  
(headlight switch is on) or nighttime level (headlight  
switch is off).  
Clock Time Setting  
SIC4559  
NOTE:  
4. Turn the Selection dial to select the day of the  
week, then press the Enter button to apply the  
selection.  
Clock Time Setting is used for displaying the  
ECO information. See “ECO information” (P.2-  
22).  
SIC4603  
5. Turn the Selection dial to select the hour and AM  
or PM, then press the Enter button to apply the  
selection.  
4. Turn the Selection dial to select the preferred  
language, then press the Enter button to apply the  
selection. A red indicator will appear next to the  
2-20 Instruments and controls  
language that is selected.  
Auto Interior Illumination  
Selective Door Unlock (if equipped)  
Select Units  
SIC4605  
SIC4606  
SIC4580  
Select to turn the illumination of the interior lights on or  
off when any door is unlocked.  
When this item is turned on, only the driver’s door is  
unlocked after the door unlock operation is performed  
once. All of the doors can be unlocked if the door  
unlock operation is performed again within 1 minute.  
1. Press the Drive Mode Select button.  
2. Press the SETUP button.  
1. Press the Drive Mode Select button.  
2. Press the SETUP button.  
3. Turn the Selection dial to “Select Units” then press  
the Enter button.  
When this item is turned off, all the doors will be  
unlocked after the door unlock operation is performed  
once.  
3. Turn the Selection dial to “Auto Interior Illumina-  
tion” then press the Enter button.  
The item selected with the selection dial will  
change color.  
The item selected with the selection dial will  
change color.  
1. Press the Drive Mode Select button.  
2. Press the SETUP button.  
4. Turn the Selection dial to select “ON” or “OFF”,  
then press the Enter button to apply the selection.  
The indicator will turn red when auto interior  
illumination is on.  
3. Turn the Selection dial to “Selective Door Unlock”  
then press the Enter button.  
The item selected with the selection dial will  
change color.  
4. Turn the Selection dial to select “ON” or “OFF”,  
then press the Enter button to apply the selection.  
The indicator will turn red when selective door  
unlock is on.  
SIC4604  
4. Turn the Selection dial to select “km, l/100km” or  
“miles, MPG”, then press the Enter button to apply  
the selection.  
Instruments and controls 2-21  
Auto Headlight Sensitivity (if equipped)  
DRIVE INFORMATION  
G-Force screen (if equipped)  
SIC4607  
SIC4615  
SIC4618  
Select to adjust the sensitivity of the automatic  
headlight.  
While in the Drive Mode, push the Drive information  
button to display elapsed time, average speed and trip  
CAUTION:  
distance. Pressing the Drive information button  
second time or turn the Selection dial will display a  
G (gravity)-Force screen.  
a
There may be a delay between the information  
displayed on the screen and the actual move-  
ment of the vehicle. This is not a malfunction.  
1. Press the Drive Mode Select button.  
2. Press the SETUP button.  
3. Turn the Selection dial to “Auto Headlight  
Sensitivity” then press the Enter button.  
Elapsed time  
The elapsed time shows the time since the last reset.  
The G (gravity)-Force screen displays the current  
acceleration and deceleration (front-to-rear) and cor-  
nering (side-to-side) G-Force on the vehicle at three  
stages.  
The item selected with the selection dial will  
change color.  
Average speed (km/h or MPH)  
The average speed shows the average vehicle speed  
since the last reset.  
ECO INFORMATION  
Trip distance (km or MILES)  
CAUTION:  
The trip distance shows the distance driven since the  
last reset.  
Do not adjust the display controls while driving  
so that full attention may given to vehicle  
operation. It will not operate if adjusted while  
driving.  
To reset the elapsed time, average speed and trip  
distance, push the enter button for more than one  
second. All three drive information displays will reset at  
the same time.  
The following ECO INFO mode will appear on the  
display by pushing the ECO information button, then  
turning the Selection dial to scroll through the different  
screens.  
SIC4583  
4. Turn the Selection dial to + to increase sensitivity  
or to − to decrease sensitivity, then press the Enter  
button to apply the selection.  
While driving, only one ECO information screen is  
2-22 Instruments and controls  
displayed. The vehicle must be stopped to scroll  
through the different screens.  
Reset at Start  
Records of up to the past 4 times of each time of  
ignition switch ON fuel consumption can be shown on  
the display.  
Manual Reset  
Records of up to the past 4 times of resetting fuel  
consumption can be shown on the display.  
The displayed ECO INFO can be reset by pushing the  
Enter button for more than 1 second.  
JVI1142X  
Daily Reset  
Weekly Reset  
Records of up to the past 4 days of fuel consumption  
can be shown on the display.  
Records of up to the past 4 weeks of each week’s fuel  
consumption can be shown on the display.  
NOTE:  
When the clock is not set, the ECO information  
(daily and weekly) cannot be used.  
Instruments and controls 2-23  
HEADLIGHT AND TURN SIGNAL  
SWITCH  
windshield wiper is operated continuously).  
HEADLIGHT SWITCH  
XENON HEADLIGHTS (if equipped)  
When the ignition switch is placed in the “OFF”  
position, the lights will turn off automatically.  
WARNING:  
HIGH VOLTAGE  
.
.
When xenon headlights are on, they produce  
a high voltage. To prevent an electric shock,  
never attempt to modify or disassemble.  
Always have your xenon headlights checked  
and/or replaced at a NISSAN dealer.  
Xenon headlights provide considerably  
more light than conventional headlights. If  
they are not correctly aimed, they might  
temporarily blind an oncoming driver or a  
SIC3782  
Type A  
SAA0642A  
driver ahead of you and could cause  
a
serious accident. Immediately take your  
vehicle to a NISSAN dealer and have the  
headlights adjusted correctly.  
CAUTION:  
Do not place any objects on top of the sensor  
A
* . The sensor senses the brightness level and  
When the xenon headlights are initially turned on, their  
brightness and color vary slightly. However, the color  
and brightness will soon stabilize.  
controls the autolight function. If the sensor is  
covered, it reacts as if it is dark, and the  
headlights will illuminate.  
The life of xenon headlights will be shortened by  
frequent on-off operation. It is generally desirable not  
to turn off the headlights for short intervals.  
position  
SIC3783  
Type B  
The  
position turns on the front clearance,  
If the xenon headlight bulb is close to burning out, the  
brightness will drastically decrease, the headlight will  
start blinking, or the color of the headlight will become  
reddish. If one or more of the above conditions appear,  
contact a NISSAN dealer.  
NISSAN recommends that you consult the local  
regulations concerning the use of lights.  
instrument panel, tail and license plate lights.  
position  
AUTO position (if equipped)  
The  
position turns on the headlights in addition to  
When the ignition switch is in the “ON” position and  
the headlight switch is in the “AUTO” position, the  
headlights, front clearance lights, instrument panel  
lights, rear combination lights and other lights turn on  
automatically depending on the brightness of the  
surroundings.  
the other lights.  
Except for Korea: The headlights will turn on auto-  
matically at twilight or in rainy weather (when the  
2-24 Instruments and controls  
“OFF” or “LOCK” position.  
Headlight beam  
HEADLIGHT AIMING CONTROL (if  
equipped)  
Be sure to turn the headlight switch to the “OFF” or  
“AUTO” position (if equipped) when you leave the  
vehicle.  
Manual type  
Except for Korea:  
When the headlight switch is in the  
or  
position while the engine is running, the lights will  
automatically turn off after placing the ignition switch in  
the “ACC”, “OFF” or “LOCK” position and opening the  
driver’s side door (if equipped).  
When the headlight switch remains in either the  
JVI1164X  
or  
position after the lights automatically turn off,  
Example  
the lights will turn on when the ignition switch is placed  
in the “ON” position or the engine is started.  
To turn on the high beam, push the lever towards the  
SIC2275  
1
front position  
.
*
For Korea:  
To turn off the high beam, return the lever to the neutral  
The headlight aiming control operates when the  
ignition switch is in the “ON” position and the headlight  
is on to allow the headlight axis to be adjusted  
according to the driving condition.  
When the headlight switch is in the  
or  
2
position  
.
*
position while the ignition switch is in the “ON”  
position, the lights will automatically turn off within a  
period of time after the ignition switch has been placed  
in the “OFF” position.  
To flash the headlights, pull the lever towards the  
. The headlights can be flashed  
even when the headlights are not on.  
3
*
rearmost position  
When driving with no heavy load/luggage or driving on  
a flat road, select the normal position “0”.  
When the lever is pulled towards the rearmost position  
When the headlight switch remains in the  
or  
3
after the ignition switch is placed in the “OFF” or  
*
If the number of occupants and load/luggage in the  
vehicle changes, the headlight axis may become higher  
than normal.  
position after the lights automatically turn off, the lights  
will turn on when the ignition switch is placed in the  
“ON” position.  
“LOCK” position, the headlight will turn on and stay on  
for 30 seconds. The lever can be pulled 4 times for up  
to 2 minutes (for Korea).  
If the vehicle is traveling on a hilly road, the headlights  
may directly shine on the rearview and outside mirrors  
of a vehicle ahead or the windshield of an oncoming  
vehicle, which may obscure other drivers’ vision.  
CAUTION:  
Battery saver system  
The light reminder chime will sound if the driver’s door  
is opened while the following improper operations are  
found:  
Do not leave the lights on when the engine is not  
running for extended periods of time to prevent  
the battery from being discharged.  
To adjust to the proper aiming height, turn the switch  
accordingly. The higher the number, designated on the  
switch, the lower the headlight axis.  
.
The headlight switch is in either the  
or  
position, and the ignition switch in the “ACC”,  
“OFF” or “LOCK” position.  
Select the switch position by referring to the following  
samples.  
.
The headlight switch is in the “AUTO” position (if  
equipped) and the front fog light (if equipped) is  
turned on while the ignition switch is in the “ACC”,  
Instruments and controls 2-25  
FOG LIGHT SWITCH (if equipped)  
TURN SIGNAL SWITCH  
Number Number  
of front of rear  
position seat oc- seat oc-  
cupants cupants  
Weight of load in  
luggage compart-  
ment  
Switch  
No  
0
1
1 or 2  
2
occu-  
pants  
No load  
No load  
3
Approximately 58  
kg (128 lb)*1  
Approximately 45  
kg (99 lb)*2  
Approximately 60  
kg (132 lb)*3  
SIC3811  
2
3
2
1
3
Example  
SIC3671  
Example  
FRONT FOG LIGHTS  
To turn on the front fog lights, turn the fog light switch  
Approximately  
282 kg (622 lb)*1  
Approximately  
270 kg (595 lb)*2  
Approximately  
CAUTION:  
to the  
or  
position with the headlight switch in the  
position.  
No oc-  
cupants  
The turn signal switch will not be cancelled  
automatically if the steering wheel turning angle  
does not exceed the preset amount. After a turn  
or lane change, make sure that the turn signal  
switch is returned to its original position.  
To turn off the fog lights, turn the fog light switch to the  
“OFF” position.  
284 kg (626 lb)*3  
When the headlight switch is in the “AUTO” position (if  
equipped), turning the fog light switch to the  
position will turn on the headlights, fog lights and the  
other lights while the ignition switch is in the “ON”  
position or the engine is running (if equipped).  
*1: For Brunei and Mauritius  
*2: For Thailand  
Turn signal  
*3: For Mexico and the Middle East  
To turn on the turn signals, move the lever up or down  
to the point where the lever latches. When the turn  
is completed, the turn signal cancels automatically.  
1
*
Automatic type  
For the vehicle equipped with the automatic leveling  
system, the headlight axis is controlled automatically.  
Lane change signal  
To turn on the lane change signals, move the lever up  
2
*
or down  
flash.  
to the point where the light begins to  
If the lever is moved back to its original position right  
after moving up or down, the light will flash 3 times (if  
equipped).  
To cancel the flashing, move the lever to the opposite  
direction.  
2-26 Instruments and controls  
WIPER AND WASHER SWITCH  
ignition switch is in the “ON” position.  
WARNING:  
Wiper operation  
The lever position “INT”  
intermittently. If equipped, the intermittent operation  
can be adjusted by turning the adjustment control  
In freezing temperatures, the washer fluid may  
freeze on the windshield and obscure your  
vision. Warm the windshield with the defogger  
before you wash the windshield.  
1
operates the wiper  
*
A
B
knob, (longer)  
or (shorter)  
.
*
*
2
*
The lever position “LO”  
speed.  
operates the wiper at low  
CAUTION:  
.
.
.
Do not operate the washer continuously for  
longer than 30 seconds.  
3
The lever position “HI”  
speed.  
operates the wiper at high  
*
JVI1010X  
JVI0271X  
JVI1141X  
Type B  
Type C  
Type D  
Do not operate the washer if the window  
washer fluid reservoir is empty.  
To stop the wiper operation, move the lever up to the  
“OFF” position.  
If the wiper operation is interrupted by snow  
or ice, the wiper may stop moving to protect  
its motor. If this occurs, turn the wiper switch  
to the “OFF” position and remove the snow  
or ice on and around the wiper arms. In  
approximately 1 minute, turn the switch on  
again to operate the wiper.  
4
*
The lever position “MIST”  
sweep. The lever automatically returns to its original  
position.  
operates the wiper one  
Pulling up the wiper arm:  
The wiper arm should be in the up position when  
replacing the wiper.  
Place the ignition switch in the “OFF” position from the  
“ON” position.  
WINDSHIELD WIPER AND WASHER  
SWITCH  
Within 1 minute after the ignition switch is placed in  
the “OFF” position, push up the lever  
(within 0.5 second) to pull up the wiper arm. The wiper  
operation stops in mid-operation and the wiper arm  
can be pulled up.  
4
*
twice quickly  
To return the wiper arm, place the wiper arm in the  
down position and operate the wiper switch once after  
placing the ignition switch to the “ON” position.  
CAUTION:  
Do not operate the windshield wiper while the  
wiper arm is pulled up. The wiper arm may be  
damaged.  
SIC3664  
Type A  
The windshield wiper and washer operate when the  
Instruments and controls 2-27  
DEFOGGER SWITCH  
Wiper operation  
Washer operation  
Turn the switch from the “OFF” position to operate the  
wiper.  
To operate the washer, pull the lever toward the back  
5
*
of the vehicle  
until the desired amount of washer  
fluid is spread on the windshield. The wiper will  
automatically operate several times.  
1
*
“INT” (intermittent) — intermittent operation (not  
adjustable)  
2
“ON” (low) — continuous low speed operation  
*
REAR WINDOW WIPER AND WASHER  
SWITCH  
Washer operation  
3
Push the switch forward  
to operate the washer.  
*
Then the wiper will also operate several times.  
SIC4520  
Type A  
SIC3666  
Type A  
SIC4519  
Type B  
The defogger switch operates when the ignition switch  
is in the “ON” position.  
The defogger is used to reduce the moisture, fog or  
frost on the rear window to improve the rear view.  
1
When the defogger switch  
is pushed, the indicator  
*
2
light  
illuminates and the rear window defogger  
*
operates for approximately 15 minutes. After the preset  
time has passed, the defogger will turn off automati-  
cally.  
SIC4076  
Type B  
The rear window wiper and washer operate when the  
ignition switch is in the “ON” position.  
To turn off manually, push the defogger switch again.  
2-28 Instruments and controls  
HORN  
WINDOWS  
CAUTION:  
POWER WINDOWS  
.
.
When operating the defogger continuously,  
be sure to start the engine. Otherwise, it may  
cause the battery to discharge.  
WARNING:  
.
.
Make sure that all passengers have their  
hands, etc. inside the vehicle before operat-  
ing the power windows.  
When cleaning the inner side of the window,  
be careful not to scratch or damage the  
electrical conductors on the surface of the  
window.  
Never leave children or adults who would  
normally require the support of others alone  
in the vehicle. They could unknowingly  
activate switches or controls and inadver-  
tently become involved in an accident.  
SIC4521  
The horn switch operates regardless of the ignition  
switch position except when the battery is discharged.  
The power windows operate when the ignition switch  
is in the “ON” position.  
When the horn switch is pushed and held, the horn will  
sound. Releasing the horn switch will cease the horn  
sound.  
To open a window, push down the power window  
switch.  
To close a window, pull up the power window switch.  
Driver’s window switch  
SIC4522  
The driver’s switch, the main switch, can control all  
windows.  
Instruments and controls 2-29  
Locking passengers’ windows:  
the window as it is closing by the automatic function.  
When the control unit detects an obstacle, the window  
will be lowered immediately.  
Automatic function  
A
When the lock button  
*
is pushed in, the  
passengers’ windows cannot be operated.  
Depending on the environment or driving conditions,  
the auto-reverse function may activate if an impact or  
load similar to something being caught in the window  
occurs.  
To cancel the passengers’ windows lock, push the lock  
A
button  
lock.  
again to release the passengers’ window  
*
Passenger’s window switch  
If the window does not close automatically  
If the power window automatic function (closing only)  
does not operate properly, perform the following  
procedure to initialize the power window system.  
SIC4524  
1. Place the ignition switch in the “ON” position.  
2. Close the door.  
The automatic function is available for the switch that  
has an mark on its surface.  
3. Open the window completely by operating the  
power window switch.  
The automatic function enables a window to fully open  
or close without holding the switch down or up.  
4. Pull the power window switch and hold it to close  
the window, and then hold the switch more than 3  
seconds after the window is closed completely.  
To fully open the window, push the power window  
switch down to the second detent and release the  
switch. To fully close the window, pull the power  
window switch up to the second detent and release  
the switch. The switch does not have to be held during  
window operation.  
SIC4523  
The passenger’s switch can control its corresponding  
window.  
5. Release the power window switch. Operate the  
window by the automatic function to confirm the  
initialization is complete.  
When the passengers’ windows lock button on the  
driver’s switch is pushed in, the passenger’s switch  
cannot be operated.  
If the power window automatic function does not  
operate properly after performing the procedure above,  
have your vehicle checked by a NISSAN dealer.  
To stop the window open/close operation during the  
automatic function, push down or pull up the switch in  
opposite directions.  
Auto-reverse function:  
WARNING:  
There is a small distance just before the closed  
position which cannot be detected. Make sure  
that all passengers have their hands, etc. inside  
the vehicle before closing the windows.  
The auto-reverse function enables  
a
window to  
automatically reverse when something is caught in  
2-30 Instruments and controls  
POWER OUTLET  
STORAGES  
.
.
Do not allow water to contact the outlet.  
When not in use, be sure to close the cap.  
WARNING:  
.
.
The storages should not be used while  
driving so that the full attention may be  
given to vehicle operation.  
Keep the storage lids closed while driving to  
help prevent injury in an accident or sudden  
stop.  
GLOVE BOX  
SIC4525  
The power outlet is for powering electrical acces-  
sories.  
CAUTION:  
.
.
.
The outlet and plug may be hot during or  
immediately after use.  
This power outlet is not designed for use  
with a cigarette lighter unit.  
SIC4526  
Do not use with accessories that exceed a 12  
volt, 120W (10A) power draw. Do not use  
double adapters or more than one electrical  
accessory.  
To open the glove box, pull the handle.  
To close, push the lid in until the lock latches.  
.
.
Use power outlet with the engine running to  
avoid discharging the vehicle battery.  
CUP HOLDERS  
Avoid using power outlet when the air  
conditioner, headlights or rear window de-  
fogger is on.  
WARNING:  
The driver must not remove or insert cups into  
the cup holder while driving so that full attention  
may be given to vehicle operation.  
.
.
Before inserting or disconnecting a plug, be  
sure to turn off the power switch of the  
electrical accessory being used and the  
ignition switch.  
CAUTION:  
Avoid abrupt starting and braking especially  
when the cup holder is being used to prevent  
spilling the contents. If the contents are hot, they  
Push the plug in as far as it will go. If good  
contact is not made, the plug may overheat  
or the internal temperature fuse may blow.  
Instruments and controls 2-31  
could scald you or your passengers.  
CARGO FLOOR BOX (if equipped)  
CARGO COVER (if equipped)  
Soft bottle holders  
WARNING:  
.
Never put anything on the cargo cover, no  
matter how small. Any object on it could  
cause an injury in an accident or sudden  
stop.  
.
Do not leave the cargo cover in the vehicle  
with it disengaged from the holder.  
The cargo cover keeps the luggage compartment  
contents hidden from the outside.  
SIC4529  
SIC4527  
A
*
1. To open the cargo floor box, pull the board  
COAT HOOK (if equipped)  
.
Center console  
SIC4528  
Door (front and rear)  
CAUTION:  
SIC3505  
The coat hook is located above the rear side window.  
.
.
Do not use bottle holder for any other  
CAUTION:  
objects that could be thrown about in the  
vehicle and possibly injure people during  
sudden braking or an accident.  
Do not apply a total load of more than 2 kg (4 lb)  
to the hook.  
Do not use bottle holder for open liquid  
containers.  
SIC4584  
2-32 Instruments and controls  
SUN VISORS  
SUNROOF (if equipped)  
To remove the cargo cover:  
1. Open the back door.  
WARNING:  
.
.
In an accident you could be thrown from the  
vehicle through an open sunroof. Adults  
should always use seat belts and children  
should always use seat belts or child  
restraint system.  
B
2. Remove the clip  
*
from the back door side  
B
garnish by turning the clip  
counterclockwise  
*
1
B
2
and pulling the clip  
toward you  
.
*
*
*
A
*
3. Remove the clip  
garnish.  
from the back door lower  
Never allow anyone to stand up or extend  
any portion of their body out of the opening  
while the vehicle is in motion or while the  
sunroof is closing.  
To install the cargo cover:  
1. Open the back door.  
A
2. Fix the clip  
3. Fix the clip  
on the back door lower garnish.  
on the back door side garnish  
*
B
*
CAUTION:  
using the same procedure as removing the cargo  
cover but in the reverse order.  
.
.
Remove water drops, snow, ice or sand from  
the sunroof before opening.  
Do not place any heavy object on the  
sunroof or surrounding area.  
AUTOMATIC SUNROOF  
SIC2872  
1. To block out glare from the front, swing down the  
1
*
sun visor  
.
2. To block glare from the side, remove the sun visor  
from the center mount and swing it to the side  
2
.
*
SIC4624  
The sunroof only operates when the ignition switch is  
in the “ON” position.  
Instruments and controls 2-33  
INTERIOR LIGHTS  
Depending on the environment or driving conditions,  
the auto reverse function may be activated if an impact  
or load similar to something being caught in the  
sunroof occurs.  
Sunshade  
CAUTION:  
To open or close the sunshade, slide the sunshade  
manually.  
.
.
Do not leave the light switch on when the  
engine is not running for extended periods  
of time to prevent the battery from being  
discharged.  
The sunshade will open automatically when the  
sunroof is opened. The sunshade needs to be closed  
manually by sliding it.  
If sunroof does not operate  
If the sunroof does not operate properly, perform the  
following procedure to initialize the sunroof operation  
system.  
Turn off the lights when you leave the  
vehicle.  
Sunroof  
Tilting:  
1. If the sunroof is open, close it fully by repeatedly  
MAP LIGHTS  
To tilt up, first close the sunroof by pushing the switch  
toward  
again and release it; it need not be held. To tilt down  
the sunroof, push the switch toward  
2
*
pushing the switch toward  
.
2
*
2
*
. Push the switch toward  
2
*
2. Push and hold the switch toward  
the sunroof up.  
to tilt  
1
*
.
3. Release the sunroof switch after the sunroof  
moves slightly up and down.  
Sliding:  
To fully open or close the sunroof, push the switch  
1
4. Push and hold the switch toward  
tilt the sunroof down.  
to fully  
*
1
2
toward  
or  
and release it; it need not  
*
*
be held. The roof will automatically open or close all the  
way. To stop the roof, push the switch in any direction  
while it is opening or closing.  
5. Check if the sunroof switch operates normally.  
If the sunroof does not operate properly after perform-  
ing the procedure above, have your vehicle checked by  
a NISSAN dealer.  
SIC4572  
Auto reverse function  
Operate the map light switch to turn the map light on  
or off.  
WARNING:  
There is a small distance just before the closed  
position which cannot be detected. Make sure  
that all passengers have their hands, etc. inside  
the vehicle before closing the sunroof.  
1
: ON position  
*
2
*
: OFF position  
The auto reverse function can be activated when the  
sunroof is closed by automatic operation when the  
ignition switch is in the “ON” position. If the control unit  
detects something caught in the sunroof when it is  
closing, the sunroof will be immediately opened.  
If the sunroof cannot be closed automatically when the  
auto reverse function activates due to a malfunction,  
2
*
push and hold the switch toward  
.
2-34 Instruments and controls  
“LOCK” position  
MAP LIGHT CONTROL SWITCH  
— remain on for about 15 seconds.  
.
.
any door is opened and then closed with the  
ignition switch in the “LOCK” position  
— remain on for about 15 seconds.  
any door is opened with the ignition switch in the  
“ACC” or “ON” position  
— remain on while the door is opened. When the  
door is closed, the lights go off.  
Battery saver system  
The lights will turn off after a period of time when the  
lights remain illuminated to prevent the battery from  
becoming discharged.  
SIC4573  
The map lights control switch has three positions: ON  
1
2
, OFF  
and center.  
*
*
CARGO ROOM LIGHTS  
ON position  
When the switch is in the ON position  
lights will illuminate.  
The cargo room lights illuminate when the back door is  
opened. When the back door is closed, the lights will  
turn off.  
1
, the map  
, the map  
*
OFF position  
When the switch is in the OFF position  
2
*
lights will not illuminate, regardless of the condition.  
Center position  
When the switch is in the center position, the map  
lights will illuminate under the following conditions:  
.
.
.
ignition switch is placed in the “OFF” position  
(models with Intelligent Key system)  
— remain on for about 15 seconds.  
the key is removed from the ignition switch  
(models without Intelligent Key system)  
— remain on for about 15 seconds.  
doors are unlocked by pushing the “UNLOCK”  
button (on the remote controller or Intelligent  
Key) or the request switch (Intelligent Key system  
equipped models), with the ignition switch in the  
Instruments and controls 2-35  
MEMO  
2-36 Instruments and controls  

Related Topics

Cockpit Instrument panel Meters and gauges Warning/indicator lights and audible reminders Integrated control system Headlight and turn signal switch Fog light switch Wiper and washer switch Defogger switch Horn Windows Power outlet Storages Sun visors Sunroof Interior lights

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot