2010-2019 Nissan Juke SUV Instruments and controls -> Sunroof User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Instruments and controls -> Sunroof for Your Nissan Juke SUV First Generation (2010-2019)

SUN VISORS  
SUNROOF (if equipped)  
To remove the cargo cover:  
1. Open the back door.  
WARNING:  
.
.
In an accident you could be thrown from the  
vehicle through an open sunroof. Adults  
should always use seat belts and children  
should always use seat belts or child  
restraint system.  
B
2. Remove the clip  
*
from the back door side  
B
garnish by turning the clip  
counterclockwise  
*
1
B
2
and pulling the clip  
toward you  
.
*
*
*
A
*
3. Remove the clip  
garnish.  
from the back door lower  
Never allow anyone to stand up or extend  
any portion of their body out of the opening  
while the vehicle is in motion or while the  
sunroof is closing.  
To install the cargo cover:  
1. Open the back door.  
A
2. Fix the clip  
3. Fix the clip  
on the back door lower garnish.  
on the back door side garnish  
*
B
*
CAUTION:  
using the same procedure as removing the cargo  
cover but in the reverse order.  
.
.
Remove water drops, snow, ice or sand from  
the sunroof before opening.  
Do not place any heavy object on the  
sunroof or surrounding area.  
AUTOMATIC SUNROOF  
SIC2872  
1. To block out glare from the front, swing down the  
1
*
sun visor  
.
2. To block glare from the side, remove the sun visor  
from the center mount and swing it to the side  
2
.
*
SIC4624  
The sunroof only operates when the ignition switch is  
in the “ON” position.  
Instruments and controls 2-33  
INTERIOR LIGHTS  
Depending on the environment or driving conditions,  
the auto reverse function may be activated if an impact  
or load similar to something being caught in the  
sunroof occurs.  
Sunshade  
CAUTION:  
To open or close the sunshade, slide the sunshade  
manually.  
.
.
Do not leave the light switch on when the  
engine is not running for extended periods  
of time to prevent the battery from being  
discharged.  
The sunshade will open automatically when the  
sunroof is opened. The sunshade needs to be closed  
manually by sliding it.  
If sunroof does not operate  
If the sunroof does not operate properly, perform the  
following procedure to initialize the sunroof operation  
system.  
Turn off the lights when you leave the  
vehicle.  
Sunroof  
Tilting:  
1. If the sunroof is open, close it fully by repeatedly  
MAP LIGHTS  
To tilt up, first close the sunroof by pushing the switch  
toward  
again and release it; it need not be held. To tilt down  
the sunroof, push the switch toward  
2
*
pushing the switch toward  
.
2
*
2
*
. Push the switch toward  
2
*
2. Push and hold the switch toward  
the sunroof up.  
to tilt  
1
*
.
3. Release the sunroof switch after the sunroof  
moves slightly up and down.  
Sliding:  
To fully open or close the sunroof, push the switch  
1
4. Push and hold the switch toward  
tilt the sunroof down.  
to fully  
*
1
2
toward  
or  
and release it; it need not  
*
*
be held. The roof will automatically open or close all the  
way. To stop the roof, push the switch in any direction  
while it is opening or closing.  
5. Check if the sunroof switch operates normally.  
If the sunroof does not operate properly after perform-  
ing the procedure above, have your vehicle checked by  
a NISSAN dealer.  
SIC4572  
Auto reverse function  
Operate the map light switch to turn the map light on  
or off.  
WARNING:  
There is a small distance just before the closed  
position which cannot be detected. Make sure  
that all passengers have their hands, etc. inside  
the vehicle before closing the sunroof.  
1
: ON position  
*
2
*
: OFF position  
The auto reverse function can be activated when the  
sunroof is closed by automatic operation when the  
ignition switch is in the “ON” position. If the control unit  
detects something caught in the sunroof when it is  
closing, the sunroof will be immediately opened.  
If the sunroof cannot be closed automatically when the  
auto reverse function activates due to a malfunction,  
2
*
push and hold the switch toward  
.
2-34 Instruments and controls  

Related Topics

Popular Owner Manuals