2010-2019 Nissan Juke SUV Instruments and controls -> Meters and gauges User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Instruments and controls -> Meters and gauges for Your Nissan Juke SUV First Generation (2010-2019)

METERS AND GAUGES  
The needle indicators may move slightly after  
the ignition switch is placed in the “OFF” or  
“LOCK” position. This is not a malfunction.  
SIC4504  
Type A  
SIC4503  
SIC4738  
1.  
2.  
3.  
Tachometer  
5.  
6.  
7.  
8.  
Speedometer  
Type B  
Engine coolant temperature gauge  
Vehicle information display  
— Odometer/twin trip odometer  
— Trip computer  
Warning/indicator lights  
Instrument brightness control knob  
Continuously Variable Transmission (CVT) posi-  
tion indicator*  
9.  
*:  
RESET switch for trip odometer/Trip computer  
mode switch  
— Cruise control*  
— Outside air temperature  
— Engine oil information*  
Fuel gauge  
if equipped  
4.  
2-6 Instruments and controls  
Resetting trip odometer:  
the engine coolant temperature.  
SPEEDOMETER  
3
Push the reset switch  
*
for approximately 1 second  
to reset the trip odometer to zero.  
The engine coolant temperature is normal when the  
The speedometer indicates the vehicle speed (km/h or  
MPH).  
2
*
gauge is within the zone  
shown in the illustration.  
The engine coolant temperature will vary with the  
outside air temperature and driving conditions.  
TACHOMETER  
ODOMETER  
Odometer/Twin trip odometer  
CAUTION:  
.
If the gauge indicates engine coolant tem-  
perature near the hot end of the normal  
range, reduce vehicle speed to decrease  
temperature.  
.
.
If the gauge is over the normal range, stop  
the vehicle as soon as safely possible.  
If the engine is overheated, continued op-  
eration of the vehicle may seriously damage  
the engine. (See “If your vehicle overheats”  
(P.6-8) for immediate action required.)  
SIC4506  
The tachometer indicates the engine speed in revolu-  
tions per minute (rpm). Do not rev the engine into  
SIC4505  
The odometer/twin trip odometer is displayed when  
the ignition switch is in the “ON” position.  
1
the red zone  
.
*
FUEL GAUGE  
The red zone varies with models.  
1
The odometer  
displays the total distance the  
*
ENGINE COOLANT TEMPERATURE  
GAUGE  
vehicle has been driven.  
2
*
The twin trip odometer  
individual trips.  
displays the distance of  
Changing trip odometer display:  
3
Push the reset switch  
follows:  
to change the display as  
*
TRIP A ? TRIP B ? Trip computer mode ?TRIP A  
For trip computer information, see “Trip computer”  
(P.2-9).  
SIC4252  
1
The fuel gauge  
indicates the approximate fuel level  
*
in the tank when the ignition switch is in the “ON”  
position.  
SIC4123  
The gauge may move slightly during braking, turning,  
accelerating, or going up and down hills due to  
1
The engine coolant temperature gauge  
*
indicates  
Instruments and controls 2-7  
movement of fuel in the tank.  
The low fuel warning light  
When the ignition switch is placed in the “ON”  
position, the vehicle information display shows the  
following information:  
2
*
illuminates when  
the fuel level in the tank is getting low. Refuel as soon  
1.  
2.  
Outside air temperature  
as it is convenient, preferably before the gauge reads  
0.  
Continuously Variable Transmission (CVT) posi-  
tion indicator (if equipped)  
The arrow,  
, indicates that the fuel filler lid is  
3.  
4.  
Odometer/Instrument brightness control display  
located on the right side of the vehicle.  
Twin trip odometer/Trip computer/Cruise control  
display (if equipped)  
CAUTION:  
Engine oil information is also displayed on the vehicle  
information display when required (if equipped).  
Refuel before the gauge reads 0 (empty).  
SIC4256  
There is a small reserve of fuel in the tank when the fuel  
gauge reads 0 (empty).  
The instrument brightness control operates when the  
ignition switch is in the “ON” position.  
For the cruise control (if equipped), see “Cruise  
control” (P.5-19).  
A
Push the control knob  
to adjust the brightness of  
*
Malfunction Indicator Light (MIL)  
For Korea:  
OUTSIDE AIR TEMPERATURE  
The outside air temperature is displayed in 8C.  
B
the meter panel. The brightness indicator  
shown briefly in the vehicle information display when  
the control is pushed.  
will be  
*
If the Malfunction Indicator Light (MIL) illuminates while  
the engine is running, it may indicate that the fuel filler  
cap is loose or missing, or that the fuel level is low.  
Make sure that the fuel filler cap is installed and closed  
tightly, and that a sufficient amount of fuel remains in  
the fuel tank. (See “Malfunction Indicator Light (MI or  
MIL)” (P.2-16).)  
When the outside air temperature becomes 38C  
(378F) or lower, the outside air temperature display  
blinks to give a warning.  
When the brightness level reaches the maximum or  
minimum, a beep will sound.  
The display will stop blinking after 1 minute or when  
the outside air temperature becomes 48C (398F) or  
above.  
CONTINUOUSLY VARIABLE TRANSMIS-  
SION (CVT) POSITION INDICATOR (if  
equipped)  
INSTRUMENT BRIGHTNESS CONTROL  
The Continuously Variable Transmission (CVT) position  
indicator indicates the shift lever position when the  
ignition switch is in the “ON” position.  
VEHICLE INFORMATION DISPLAY  
SIC4517  
SIC4516  
2-8 Instruments and controls  
when the fuel level is low, the dte mode is automatically  
selected and the digits and the low fuel warning light  
blink in order to draw the driver’s attention. Push  
A
TRIP COMPUTER  
ENGINE OIL INFORMATION (if equipped)  
the trip computer mode switch  
to return to the  
*
mode that was selected before the warning occurred.  
When the fuel level drops even lower, the dte display  
will change to “----”.  
.
If the amount of fuel added is small, the  
display just before the ignition switch is  
turned off may continue to be displayed.  
.
When driving uphill or rounding curves, the  
fuel in the tank shifts, which may momenta-  
rily change the display.  
SIC4518  
SIC3396  
The switch for the trip computer is located on the  
meter panel.  
When the ignition switch is in the “ON” position,  
engine oil information is displayed on the vehicle  
information display in the following order:  
Average fuel consumption (l/100 km or mpg)  
The average fuel consumption mode shows the  
average fuel consumption since the last reset. Reset-  
ting is done by pushing the trip computer setting  
A
When the ignition switch is placed in the “ON”  
position, modes of the trip computer can be selected  
Distance to oil change (with a wrench symbol) ? Oil  
level indication (“Oil Good” or “Oil Lo”)  
A
by pushing the trip computer mode switch  
.
*
switch  
for longer than 1 second.  
*
A
A
Each time the trip computer mode switch  
pushed, the display will change as follows:  
is  
Push the trip computer mode switch  
for  
5
*
*
The display is updated every 30 seconds. At about the  
first 500 m (1/3 miles) after a reset, the display shows  
“----”.  
seconds while the oil level indication is displayed.  
When the “Oil Good” is indicated, a detail of the oil  
(TRIP A ? TRIP B) ? Current fuel consumption ?  
Distance to empty (dte) ? Average fuel consumption  
? Elapsed time (? TRIP A)  
5
1
level (  
-
) appears as illustrated.  
* *  
Elapsed time (h:m:s)  
CAUTION:  
The elapsed time mode shows the time since the last  
reset. The displayed time can be reset by pushing the  
Current fuel consumption  
The current fuel consumption mode shows the current  
fuel consumption.  
The oil level should be checked regularly.  
Operating with an insufficient amount of oil  
can damage the engine and such damage is not  
covered by the warranty.  
A
*
trip computer mode switch  
second.  
for longer than 1  
Distance to empty (dte — km or mls)  
Resetting displays  
When the average fuel consumption, elapsed time or  
TRIP B is displayed, push the trip computer mode  
The distance to empty (dte) mode provides you with an  
estimation of the distance that can be driven before  
refueling. The dte is constantly being calculated, based  
on the amount of fuel in the fuel tank and the actual fuel  
consumption.  
(See “Engine oil” (P.8-8) for checking the oil level.)  
A
switch  
for longer than 3 seconds. The display of  
*
average fuel consumption, elapsed time and trip  
odometer (TRIP B only) will be reset at the same time.  
The display is updated every 30 seconds.  
The dte mode includes a low range warning feature:  
Instruments and controls 2-9  
2. While the display is flashing, push the trip  
Setting distance to oil change  
The distance to oil change interval can be adjusted or  
disabled using the trip computer mode switch  
A
*
computer mode switch  
adjusting mode.  
again to enter the  
A
*
.
A
*
3. Push the trip computer mode switch  
interval reads 0.  
until the  
Refer to the separate maintenance booklet for the  
appropriate distance to oil change interval.  
If no further action is taken, the display will switch to  
the oil level indication and the oil change reminder is  
cancelled.  
To adjust oil change interval:  
A
1. Push and hold the trip computer mode switch  
*
for more than 3 seconds while the wrench symbol  
and distance to oil change information are  
displayed.  
No wrench symbol or distance will be displayed when  
the ignition switch is placed in the “ON” position. To  
reactivate the reminder, set the distance to oil change  
interval to a value above zero (0).  
If adjusting the distance from zero (0): Push and  
hold the trip computer mode switch  
than 3 seconds within 5 seconds of placing the  
ignition switch in the “ON” position.  
A
*
for more  
The wrench symbol and the distance will start  
flashing.  
2. While the display is flashing, push the trip  
A
*
computer mode switch  
adjusting mode.  
again to enter the  
If adjusting the distance from zero (0): Push the  
A
trip computer mode switch  
.
The default  
*
distance to oil change will be restored.  
A
3. Push the trip computer mode switch  
to  
*
increase the interval. Each push increases the  
interval by 1,000 km (500 miles).  
If no further action is taken, the display will switch to  
the oil level indication and the new interval will be set.  
To cancel oil change reminder:  
A
1. Push and hold the trip computer mode switch  
*
for more than 3 seconds while the wrench symbol  
and distance to oil change information are  
displayed.  
The wrench symbol and the distance will start  
flashing.  
2-10 Instruments and controls  

Related Topics

Instruments and controls
Cockpit Instrument panel Warning/indicator lights and audible reminders Integrated control system Headlight and turn signal switch Fog light switch Wiper and washer switch Defogger switch Horn Windows Power outlet Storages Sun visors Sunroof Interior lights

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot