Get Instruments and controls -> Integrated control system Guide for Nissan Juke SUV First Generation (2010-2019)

INTEGRATED CONTROL SYSTEM (if

equipped)

The Integrated Control System is located below the

audio system. Two Integrated Control System modes

can be selected: Drive mode and Climate Control

mode.

.

The chime will also sound for 2 seconds when the

ignition switch is placed in the “ACC”, “OFF” or

“LOCK” position while the fog lights (if equipped)

are on with the headlight switch in the “AUTO”

position (if equipped).

Depending on which Integrated Control System mode

is selected (Drive mode or Climate Control mode), the

screen display and some button functions will change.

Be sure to turn the headlight switch to the “OFF” or

“AUTO” position (if equipped) and the fog light (if

equipped) switch to the “OFF” position when you leave

the vehicle.

.

Drive mode

In the Drive mode, three types of driving modes

can be selected: NORMAL, SPORT and ECO.

See “Integrated control system” (P.5-15). In

addition, while in the Drive mode, SETUP, Drive

information and ECO information can be displayed

and adjusted. See “Integrated control system”

(P.5-15).

Parking brake reminder

The chime will sound if the vehicle is driven at more

than 7 km/h (4 MPH) with the parking brake applied.

Stop the vehicle and release the parking brake.

Climate Control mode

In the Climate Control mode, the climate control

can be set and adjusted. See “Automatic air

conditioner (models with Integrated Control Sys-

tem)” (P.4-13).

DRIVE MODE

When the Drive mode select button is pressed, the

display and buttons appear as shown.

2-18 Instruments and controls

.

Selective Door Unlock (if equipped)

Auto Headlight Sensitivity (if equipped)

CLIMATE ECO

NOTE:

.

The SETUP function cannot be adjusted

while driving. If you try to adjust the SETUP

function while driving, a blank screen will be

displayed.

.

When the battery is disconnected, the SET-

UP memory is erased and reverts to the

default settings. If necessary, reset the

SETUP memory after reconnecting the bat-

tery.

.

When in the Drive Mode, Display Brightness

and Button Brightness can be set to the

daytime mode or nighttime mode by press-

ing the SETUP button for more than

second (if equipped).

1

Setting Display Brightness or Button Bright-

ness

SIC4623

1.

2.

3.

4.

5.

6.

7.

8.

9.

Drive mode select button

SETUP button

SETUP FUNCTION

While in the Drive Mode, the following items can be set

up by pressing the SETUP button.

NORMAL drive mode button

SPORT drive mode button

ECO drive mode button

Display screen

.

Display Brightness

Button Brightness

Clock Time Setting

Select Language

Select Units

SIC4617

Drive information button

ECO information button

ENTER button/Selection dial

1. Press the Drive Mode Select button.

2. Press the SETUP button.

Auto Interior Illumination

Instruments and controls 2-19

3. Turn the Selection dial to “Display Brightness” or

“Button Brightness” then press the Enter button.

6. Turn the Selection dial to select the minutes, then

press the Enter button to apply the selection.

The item selected with the selection dial will

change color.

Select Language

SIC4558

1. Press the Drive Mode Select button.

2. Press the SETUP button.

SIC4560

3. Turn the Selection dial to “Clock Time Setting”,

then press the Enter button.

SIC4557

1. Press the Drive Mode Select button.

2. Press the SETUP button.

4. Turn the Selection dial to + to increase brightness

or to − to decrease brightness, then press the

Enter button to apply the selection.

The item selected with the selection dial will

change color.

3. Turn the Selection dial to “Select Language”, then

press the Enter button.

Display Brightness and Button Brightness can be

manually adjusted during the day (when the headlight

switch is off) or at night (when the headlight switch is

on).

The item selected with the selection dial will

change color.

When the bar is at the maximum brightness level, the

brightness level is the same as the daytime level

(headlight switch is on) or nighttime level (headlight

switch is off).

Clock Time Setting

SIC4559

NOTE:

4. Turn the Selection dial to select the day of the

week, then press the Enter button to apply the

selection.

Clock Time Setting is used for displaying the

ECO information. See “ECO information” (P.2-

22).

SIC4603

5. Turn the Selection dial to select the hour and AM

or PM, then press the Enter button to apply the

selection.

4. Turn the Selection dial to select the preferred

language, then press the Enter button to apply the

selection. A red indicator will appear next to the

2-20 Instruments and controls

language that is selected.

Auto Interior Illumination

Selective Door Unlock (if equipped)

Select Units

SIC4605

SIC4606

SIC4580

Select to turn the illumination of the interior lights on or

off when any door is unlocked.

When this item is turned on, only the driver’s door is

unlocked after the door unlock operation is performed

once. All of the doors can be unlocked if the door

unlock operation is performed again within 1 minute.

1. Press the Drive Mode Select button.

2. Press the SETUP button.

1. Press the Drive Mode Select button.

2. Press the SETUP button.

3. Turn the Selection dial to “Select Units” then press

the Enter button.

When this item is turned off, all the doors will be

unlocked after the door unlock operation is performed

once.

3. Turn the Selection dial to “Auto Interior Illumina-

tion” then press the Enter button.

The item selected with the selection dial will

change color.

The item selected with the selection dial will

change color.

1. Press the Drive Mode Select button.

2. Press the SETUP button.

4. Turn the Selection dial to select “ON” or “OFF”,

then press the Enter button to apply the selection.

The indicator will turn red when auto interior

illumination is on.

3. Turn the Selection dial to “Selective Door Unlock”

then press the Enter button.

The item selected with the selection dial will

change color.

4. Turn the Selection dial to select “ON” or “OFF”,

then press the Enter button to apply the selection.

The indicator will turn red when selective door

unlock is on.

SIC4604

4. Turn the Selection dial to select “km, l/100km” or

“miles, MPG”, then press the Enter button to apply

the selection.

Instruments and controls 2-21

Auto Headlight Sensitivity (if equipped)

DRIVE INFORMATION

G-Force screen (if equipped)

SIC4607

SIC4615

SIC4618

Select to adjust the sensitivity of the automatic

headlight.

While in the Drive Mode, push the Drive information

button to display elapsed time, average speed and trip

CAUTION:

distance. Pressing the Drive information button

second time or turn the Selection dial will display a

G (gravity)-Force screen.

a

There may be a delay between the information

displayed on the screen and the actual move-

ment of the vehicle. This is not a malfunction.

1. Press the Drive Mode Select button.

2. Press the SETUP button.

3. Turn the Selection dial to “Auto Headlight

Sensitivity” then press the Enter button.

Elapsed time

The elapsed time shows the time since the last reset.

The G (gravity)-Force screen displays the current

acceleration and deceleration (front-to-rear) and cor-

nering (side-to-side) G-Force on the vehicle at three

stages.

The item selected with the selection dial will

change color.

Average speed (km/h or MPH)

The average speed shows the average vehicle speed

since the last reset.

ECO INFORMATION

Trip distance (km or MILES)

CAUTION:

The trip distance shows the distance driven since the

last reset.

Do not adjust the display controls while driving

so that full attention may given to vehicle

operation. It will not operate if adjusted while

driving.

To reset the elapsed time, average speed and trip

distance, push the enter button for more than one

second. All three drive information displays will reset at

the same time.

The following ECO INFO mode will appear on the

display by pushing the ECO information button, then

turning the Selection dial to scroll through the different

screens.

SIC4583

4. Turn the Selection dial to + to increase sensitivity

or to − to decrease sensitivity, then press the Enter

button to apply the selection.

While driving, only one ECO information screen is

2-22 Instruments and controls

displayed. The vehicle must be stopped to scroll

through the different screens.

Reset at Start

Records of up to the past 4 times of each time of

ignition switch ON fuel consumption can be shown on

the display.

Manual Reset

Records of up to the past 4 times of resetting fuel

consumption can be shown on the display.

The displayed ECO INFO can be reset by pushing the

Enter button for more than 1 second.

JVI1142X

Daily Reset

Weekly Reset

Records of up to the past 4 days of fuel consumption

can be shown on the display.

Records of up to the past 4 weeks of each week’s fuel

consumption can be shown on the display.

NOTE:

When the clock is not set, the ECO information

(daily and weekly) cannot be used.

Instruments and controls 2-23

Instruments and controls -> Integrated control system for Your Nissan Juke SUV First Generation (2010-2019)

Related Topics

Popular Owner Manuals

Latest Owner Manuals