Get Driving -> Additional driving aid functions Guide for Renault Scenic 4 Door Fifth Generation (2023-2026)

ADDITIONAL DRIVING AID FUNCTIONS

To switch back to "ALL ON" mode,

press button 1 once. The indicator

light on button 1 lights up.

"ALL ON" mode

My Safety

Depending on the vehicle, the func-

tions and configurations of driving

assistance concerned are:

– overspeed sound alert ꢀ 232;

– lane departure preventionꢀ 199;

– driver vigilance warning ꢀ 230;

– emergency lane departure pre-

vention ꢀ 206.

When the "All on" mode is activated:

the "My Safety All ON selected" mes-

sage is displayed on the instrument

panel to confirm this. The driving

aids that are available in the mode

are activated.

The "My Safety" function can be

used to deactivate or activate a set

of driver assistance functions simul-

taneously.

Depending on the vehicle, you can

configure the "My Safety" function

from the multimedia screen by se-

lecting the driving aid functions to

be switched off as a group.

Depending on the vehicle

and on the length of time

since the last time the en-

gine was stopped, the "ALL ON"

mode is reactivated:

3

– when the vehicle is unlocked;

or

Operation

– when a door is opened;

or

– when the engine is restarted.

"Perso" mode

You can use this mode to deactivate

or reactivate certain driving aids

that are available in the "All on"

mode previously configured using

the "MY SAFETY PERSO" setting.

With the ignition on, press button 1

twice in succession to activate "Per-

so" mode. The first time you press it,

the "Press again for My Safety Per-

so" message is displayed on the in-

strument panel. On the second

press, the indicator light on the but-

ton 1 goes out. "Perso" mode is acti-

vated. The "My Safety Perso select-

ed" message is displayed on the in-

strument panel.

Configuration of Perso mode

For safety reasons, car-

ry out any adjustments

while the vehicle is sta-

tionary.

1 9 8 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

– performs corrective action on the

Lane departure prevention

steering system.

The "MY SAFETY PERSO"

settings saved for "Perso"

mode are stored each

You can retake control of

the vehicle at any time by

operating the steering

wheel.

time the engine is or when the

doors are locked.

3

From the multimedia screen 2

Location of the camera 1

Make sure the windscreen is not ob-

scured (by dirt, mud, snow, conden-

sation etc.).

This function is an ad-

ditional driving aid. This

function is not under

Using information from the 1 cam-

era, the function triggers corrective

action on the vehicle steering sys-

tem when a continuous or broken

line is crossed or when approaching

the roadside (divider, barrier, pave-

ment, embankment, etc.) without

activating the direction indicator

lights.

any circumstances in-

tended to replace the due care

and attention of the driver, who

should at all times be in control

of the vehicle.

Please refer to the multimedia in-

structions for more information.

Depending on the setting, in the

event of crossing a broken line with-

out activating the direction indica-

tor lights, the function:

– warns the driver without correc-

tive action on the steering system;

or

D r i v i n g - 1 9 9

ADDITIONAL DRIVING AID FUNCTIONS

Activation/deactivation

Using the switch 3

Operation

From the multimedia screen 2

3

When the function is activated, the

– To deactivate the function, if it has

been deactivated from the "Perso"

mode of the "My Safety" function

ꢀ 198, press switch 3 twice. The

warning light and the left-

hand and right-hand line indicators

4 are displayed in grey on the instru-

ment panel.

The function is set to emit a warning

or to operate when the vehicle

Please refer to the multimedia in-

structions for more information.

warning light is displayed in

yellow on the instrument panel.

– To reactivate the function, press

the 3 switch once. Warning light

speed is between approximately 40

mph (65 km/h) and 112 mph (180 km/

comes on the instrument pan-

el.

h) and if the

warning light and

the left-hand and right-hand line in-

dicators 4 appear in white.

The function is in operation if the ve-

hicle

2 0 0 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

– approaches a roadside without

activating the direction indicators;

– crosses a continuous line without

activating the direction indicators;

– crosses a broken line without acti-

vating the direction indicators, if the

"Dashed line intervention" setting is

selected.

– by a vibration in the steering

wheel;

You can interrupt the tra-

jectory correction at any

time by moving the steer-

and

ing wheel.

– the

warning light and the in-

dicator 4 on the side of the

breached line change to red on the

instrument panel.

Note: on bends, the function allows

for slightly cutting the bend.

3

Vehicle equipped with "Active

Driver Assist"

In these cases:

– the function triggers an action on

the vehicle's steering system to cor-

rect the vehicle trajectory;

If the "Lane Centring" function is ac-

tivated at the same time as the

"Lane departure prevention" func-

tion, the display of the warning light

will vary as follows:

Special cases

"Keep control" warning

– the

warning light and the in-

dicator 4 on the side of the

breached line change to yellow on

the instrument panel.

If the corrective action on the steer-

ing system is not sufficient, the

– If the system is operating and

does not detect any activity on the

steering wheel, the "Keep control"

message appears on the instrument

panel accompanied by a beep and,

– the "Lane Centring" function is in

operation: the green

warning

light replaces the white or grey

warning light on the instru-

ment panel. Therefore, the "Lane

Centring" function status is given

priority in terms of informing you;

– the "Lane Centring" function is put

on standby and the "Lane Departure

Prevention" function is neither ready

depending on the vehicle, the

warning light appears in yellow until

the driver has regained control of

the vehicle.

– If the system has been in opera-

tion for too long, the "Keep control"

message appears on the instrument

panel accompanied by a beep and,

warning light and the indica-

tor 4 on the side of the breached line

change to red on the instrument

panel, accompanied by a vibration

on the steering wheel.

If the "Dashed line intervention" set-

ting is not selected, the function

sounds the alarm if the vehicle

crosses a broken line without the di-

rection indicator lights being acti-

vated and if there is no roadside

close enough to the line.

nor in operation: the grey

warning light replaces the white or

depending on the vehicle, the

warning light appears in yellow and

the indicator 4 on the side of the line

concerned flashes until the driver

has regained control of the vehicle.

grey

warning light on the in-

strument panel. Therefore, the "Lane

Centring" function status is given

priority in terms of informing you;

In this case, the function warns the

driver:

D r i v i n g - 2 0 1

ADDITIONAL DRIVING AID FUNCTIONS

– the "Lane Centring" function is put

on standby while the "Lane Depar-

ture Prevention" function is ready or

– operation of the Electronic Stabili-

– warning light

is displayed.

ty Control system;

– operation of the anti-lock braking

system;

– the active emergency braking sys-

tem is triggered;

– intervention of another function

that controls the steering system,

such as the "Lane Centring" func-

tion.

When the function is deactivated,

in operation: the

warning light

the warning light is displayed

in yellow on the instrument panel.

is displayed in red or in yellow on the

instrument panel. Therefore, the

"Lane Departure Prevention" func-

tion status is given priority in terms

of informing you.

3

Settings

In any case, you are informed at all

times of the status of the function

when it controls the steering system

of your vehicle. The most useful in-

formation is always displayed.

If the function is unavailable, the

warning light and left-hand

and right-hand correction indicators

4 change to grey on the instrument

panel.

Function temporarily unavail-

able/disabled

If the front camera is obscured, the

"Front camera without visibility"

message is displayed on the instru-

ment panel. Clean the area where

the sensors are located

The system is temporarily unavail-

able or disabled when:

– very fast lane departure;

– driving continuously on a line;

– approximately four seconds after

changing lanes;

– tight bends;

– impaired visibility;

– one of the direction indicators is

activated;

– activating the hazard warning

lights;

Automatic deactivation

The function is automatically deac-

tivated when:

– The vehicle dynamics control sys-

tem is deactivated;

– The electronic stability system is

malfunctioning;

– The anti-lock braking system is

malfunctioning;

– engaging reverse gear;

– strong acceleration;

– the lane width changes;

– a towbar is electrically connected

to the trailer hitch socket;

2 0 2 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

– "Vibration": adjust the "Lane de-

parture prevention" function steer-

ing wheel vibration level;

Using the switch 3

– "Departure anticipation": adjust

the line detection sensitivity level. To

do this, select:

– “Late”: line detected upon cross-

ing;

3

– “Standard”: line detected on ap-

proach;

– “Early” line detected nearby.

Please refer to the multimedia in-

structions for further information.

Operating faults

When the system detects an operat-

ing fault, the left-hand and right-

hand line indicators and the warning

To access the function settings from

the multimedia screen 2 , refer to the

multimedia instructions:

– "Dashed line intervention": use

this setting to select the function's

response if the vehicle crosses a

broken line without activating the di-

rection indicators:

– selected setting: the function

may trigger an action on the

vehicle's steering system to cor-

rect the vehicle trajectory;

– setting not selected: the func-

tion can warn the driver by means

of a vibration at the steering

wheel without correcting the vehi-

cle trajectory.

light

are displayed in yellow on

the instrument panel.

In some cases, they are accompa-

nied by the following message:

– «Driving assist unavailable» ;

or

– «Check Front camera» ;

or

– «Check Driving assist».

Consult an approved dealer.

D r i v i n g - 2 0 3

ADDITIONAL DRIVING AID FUNCTIONS

Warnings

This function is an additional driving aid. This function is not under any circumstances intended to replace

the due care and attention of the driver, who should at all times be in control of the vehicle.

System servicing/repairs

3

– In the event of an impact, the camera alignment may be changed, and its operation may consequently be affect-

ed. Deactivate the function and consult an authorised dealer.

– Any work in the area where the camera is located (repairs, replacements, windscreen modifications etc.) must be

carried out by a qualified professional.

Only an authorised dealer is qualified to service the system.

In the event of system disturbance

Some conditions can disturb or damage the system's operation, such as:

– windscreen obscured (by dirt, ice, snow, condensation etc.);

– a complex environment (tunnel, etc.);

– poor weather conditions (snow, rain, hail, black ice, etc.);

– poor visibility (night, fog, etc.);

– the road markings are multiple (roadworks, etc.), difficult to distinguish or irregular (e.g. partially or very faded

lines, lines too far apart, uneven road surface, etc.);

– being dazzled (glaring sun, lights of vehicles travelling in the opposite direction; etc.);

– the road is narrow, winding or undulating (tight bends, etc.);

– closely following a vehicle travelling in the same lane.

In this case, the function "Lane departure prevention" may trigger incorrectly or not at all.

Risk of unwanted, incorrect correction or no correction of trajectory.

Deactivating the function

You must deactivate the function if:

– the area of the camera has been damaged (on the windscreen side or the interior rear-view mirror side);

– the road is slippery (snow, black ice, aquaplaning, gravel etc.);

2 0 4 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

– the windscreen is cracked or distorted (do not carry out windscreen repairs in this area; have it changed by an ap-

proved dealer);

– the vehicle is towing a trailer or a caravan.

3

D r i v i n g - 2 0 5

ADDITIONAL DRIVING AID FUNCTIONS

Using information from the radar 2

and the camera 1 , the function trig-

gers corrective action on the vehicle

steering system in the event of a risk

of collision with a vehicle coming

from the opposite direction in the

adjacent lane, without the direction

indicator having been activated.

This system provides

an additional driving

aid.

Emergency lane departure

prevention

This system is not, un-

der any circumstances, intend-

ed to replace the due care and

attention of the driver, who

should at all times be in control

of the vehicle.

3

Depending on the vehicle, using in-

formation from the radars 3 and the

camera 1 , the function triggers cor-

rective action on the vehicle steer-

ing system in the event of a risk of

collision with a vehicle moving at the

same speed or at a higher speed, if

within the detection area of the rear

radars.

Location of the camera 1

Make sure the windscreen is not ob-

scured (by dirt, mud, snow, conden-

sation etc.).

Location of the front radar 2

You can retake control of

the vehicle at any time by

operating the steering

wheel.

Ensure that the radar area is not ob-

structed (dirt, mud, snow, a badly fit-

ted/attached front number plate),

impacted, modified (including paint-

work) or hidden by any accessory fit-

ted on the front of the vehicle (on the

front bumper, logo, etc.)

Location of the side radars 3

Ensure that the radar area is not ob-

structed (by dirt, mud, snow etc.), im-

pacted or modified (including paint-

work etc.).

2 0 6 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

Activating/deactivating the

function

Detection of an oncoming vehi-

cle

Using the A "My Safety" switch

3

Please refer to the multimedia in-

structions for more information.

Press switch A twice if the function

has been deactivated via the "Per-

so" mode in the "My Safety" function

ꢀ 198.

To reactivate the function, press the

switch A .

From the multimedia screen B

D r i v i n g - 2 0 7

ADDITIONAL DRIVING AID FUNCTIONS

risk of collision with a vehicle coming

from the opposite direction in an ad-

jacent lane and within the detection

zone C , without the direction indica-

tor having been activated, the sys-

tem:

This function is an ad-

ditional driving aid.

This function is not un-

der any circumstances

intended to replace the due

care and attention of the driver,

who should at all times be in

control of the vehicle.

– warns you of a collision risk:

3

the "Risk of collision" message is dis-

played on the instrument panel ac-

companied by the warning light 4 in

red, the line on the relevant side and

a beep. The symbol 5 appears for

the relevant side on the instrument

panel;

The function may not activate if the

approaching speed is greater than

approximately 124 mph (200 km/h)

(for example, you are travelling at 68

mph (110 km/h) and the vehicle is

travelling in the opposite direction in

the adjacent lane at 56 mph (91 km/

h).

and

– triggers corrective action on the

steering system.

You can interrupt the tra-

jectory correction at any

time by moving the steer-

ing wheel.

When driving at a speed between

approximately 40 mph (65 km/h)

and 68 mph (110 km/h), if there is a

2 0 8 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

If case of overtaking

3

While driving at a speed between

approximately 40 mph (65 km/h)

and 112 mph (180 km/h), when ap-

proaching a line (continuous or bro-

ken) and there is a risk of collision

with a vehicle located in the blind

spot D and it is moving in the same

direction as your vehicle or with a ve-

hicle that is rapidly approaching

from behind in an adjacent lane that

is in the detection area E , the sys-

tem:

– warns you about a risk of collision:

the warning light 6 flashes, the "Lat-

eral obstacle detected" message is

displayed on the instrument panel,

accompanied by the warning light 4

in red, the line on the relevant side

and a beep. The symbol 5 appears

D r i v i n g - 2 0 9

ADDITIONAL DRIVING AID FUNCTIONS

for the relevant side on the instru-

ment panel;

and

– triggers corrective action on the

steering system.

– the camera does not detect a line

– the vehicle dynamics control sys-

tem is deactivated;

– the electronic stability system is

malfunctioning;

– the anti-lock braking system is

malfunctioning;

(solid or broken) on the relevant side;

– the camera does not simultane-

ously detect the two boundaries of

the lane in which your vehicle is mov-

ing;

– reverse gear is engaged;

– the field of vision of the camera is

obstructed;

– a towbar is electrically connected

to the trailer hitch socket;

3

Temporarily not available / non-

activation of the system

– the

warning light appears.

– the front radar is obscured;

– depending on the vehicle, the rear

radars are obscured:

The system is temporarily unavail-

able or disabled when:

– very fast lane departure;

– driving continuously on a line;

– approximately four seconds after

changing lanes;

If the vehicle is equipped with a tow-

bar that is recognised by the system,

the message "Trailer: side radars un-

available" is displayed to inform you

that the emergency lane departure

prevention function has been deac-

tivated.

– ...

Depending on the vehicle, if one of

the side radars is obscured the mes-

sage "Side radars no visibility" will

appear on the instrument panel.

– tight bends;

– impaired visibility;

– activation of the direction indica-

tor light (only when an oncoming ve-

hicle is detected in an adjacent

lane);

– activating the hazard warning

lights;

– strong acceleration;

– the lane width changes;

– operation of the Electronic Stabili-

ty Control system;

– operation of the anti-lock braking

system;

– operation of the active emergency

braking system;

– ...

The system cannot be activated

when:

If the vehicle is towing a trailer or

caravan, unexpected or unneces-

sary corrections may occur. You can

deactivate the system to avoid un-

expected or unnecessary correc-

tions.

When the front radar is obscured,

the "Front radar no visibility" mes-

sage is displayed on the instrument

panel.

When the front camera is obscured,

the "Front camera no visibility" mes-

sage is displayed on the instrument

panel.

Operating faults

When the function detects an oper-

ating fault, the following messages

may be displayed on the instrument

panel:

– « Check Front camera » ;

or

Clean the area where the sensors

are located.

Automatically deactivating the

function

The system is automatically deacti-

vated when:

– « Front radar to check » ;

or

2 1 0 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

– « Check Driving assist » ;

or, depending on the vehicle,

– « Check Side radars ».

Consult an approved Dealer.

3

D r i v i n g - 2 1 1

ADDITIONAL DRIVING AID FUNCTIONS

Warnings

This function is an additional driving aid. This function is not under any circumstances intended to replace

the due care and attention of the driver, who should at all times be in control of the vehicle.

System servicing/repairs

3

– In the event of an impact, the alignment of the camera or radar(s) may be altered and its operation may conse-

quently be affected. Deactivate the function and consult an authorised dealer.

– Any work in the area where the camera or radars are located (replacements, repairs, windscreen modifications

etc.) must be carried out by a qualified professional.

Only an authorised dealer is qualified to service the system.

In the event of system disturbance

Some conditions can disturb or damage the system's operation, such as:

– windscreen obscured (by dirt, ice, snow, condensation etc.);

– a complex environment (tunnel, etc.);

– poor weather conditions (snow, rain, hail, black ice, etc.);

– poor visibility (night, fog, etc.);

– the road markings are multiple (roadworks, etc.), difficult to distinguish or irregular (e.g. partially or very faded

lines, lines too far apart, uneven road surface, etc.);

– being dazzled (glaring sun, lights of vehicles travelling in the opposite direction; etc.);

– the road is narrow, winding or undulating (tight bends, etc.);

– closely following a vehicle travelling in the same lane.

In this case, the "Emergency lane departure prevention" function may be incorrectly triggered or not triggered at all.

Risk of unwanted, incorrect correction or no correction of trajectory.

Deactivating the function

You must deactivate the function if:

– the camera area (on the windscreen side or the interior rear-view mirror side) or radar area(s) have been dam-

aged;

– the road is slippery (snow, black ice, aquaplaning, gravel etc.);

2 1 2 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

– the windscreen is cracked or distorted (do not carry out windscreen repairs in this area; have it changed by an ap-

proved dealer);

– the vehicle is towing a trailer or a caravan;

– the vehicle is being towed (breakdowns);

– you are not driving on a paved road.

3

D r i v i n g - 2 1 3

ADDITIONAL DRIVING AID FUNCTIONS

Blind spot warning

Special feature

3

Ensure that zone C around the

radars on each side of the rear

bumper are not obstructed (by dirt,

mud, snow, etc.).

If a radar is obscured, the "Side

radars no visibility" message will ap-

pear on the instrument panel. Clean

the area where the sensors are lo-

cated.

The function does not no-

tify the driver if the other

vehicles are not moving.

Using information from the sensors

installed on each side of the rear

bumper (area C ), the function warns

the driver:

– when a vehicle is in the blind spot

area A and travelling in the same di-

rection as your vehicle;

This function is an ad-

ditional driving aid. This

function is not under

any circumstances in-

and/or

– when there is a risk of collision with

tended to replace the due care

and attention of the driver, who

should at all times be in control

of the vehicle.

a vehicle that is in the B area and

driving faster than you on an adjoin-

ing lane.

The function warns you when your

vehicle is travelling at a speed above

approximately 9 mph (15 km/h).

2 1 4 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

If you deactivate the direction indi-

cator, the function will return to the

initial warning (display D ).

Warning light 1

Display D

Conditions for non-function

– When driving on a road with tight

3

bends;

– in reverse.

If the vehicle is equipped with a tow-

bar recognised by the system, the

"Trailer: blind spot warning off" mes-

sage is displayed on the instrument

panel to inform you that the function

is not operational.

For information on the range of

equipment adapted to your vehicle,

we advise you to consult an ap-

proved Dealer.

A warning light 1 is located on each

door mirror 2 .

Note:

– clean the 2 door mirrors regularly

so that the warning lights 1 can be

seen properly;

– if you overtake another vehicle,

the warning light 1 will only come on

if that vehicle remains for a long

enough period in your vehicle's blind

spot A .

First warning: direction indicator not

activated, the warning light 1 indi-

cates that a vehicle is detected in

the blind spot area and/or that a ve-

hicle is rapidly approaching from the

rear in an adjacent lane.

Operating faults

If the system detects a fault, the

"Check Side radars" message is dis-

played on the instrument panel.

Display E

Consult an approved dealer.

Direction indicator activated, the

warning light 1 flashes when the

function detects a vehicle in the

blind spot and/or a vehicle is rapidly

approaching from the rear on the

side towards which you will turn the

steering wheel.

D r i v i n g - 2 1 5

ADDITIONAL DRIVING AID FUNCTIONS

Due to the presence of

sensors behind the

bumper, it is advisable to

entrust any operation on the

bumper (repair, replacement,

paintwork, etc.) to a qualified

professional.

3

2 1 6 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

Warnings

– The system’s detection range operates according to a standard lane width. If you are driving in wide traf-

fic lanes, the system might not be able to detect a vehicle in the blind spot.

– In the event of very bad weather conditions (heavy rain, snow, etc.), the system may be temporarily dis-

rupted. Remain aware of driving conditions.

3

There is a risk of accidents.

This function is an additional driving aid. This function is not under any circumstances intended to replace

the due care and attention of the driver, who should at all times be in control of the vehicle.

The driver should always adapt their speed to the traffic conditions, regardless of the system indications.

The system should under no circumstances be taken to be an obstacle detector or an anti-collision system.

System servicing/repairs

– In the event of an impact, radar alignment may be changed, and its operation will consequently be affected. Con-

sult an approved Dealer.

– Any work in the area where the radars are located (repairs, replacements, etc.) must be carried out by a qualified

professional.

Only an authorised dealer is qualified to service the system.

System disturbance

Some conditions can disturb or damage the system's operation, such as:

– complex surroundings (metal bridges, tunnels, roads with barriers at the edge, etc.);

– poor weather conditions (snow, hail, black ice, etc.);

– the vehicle is fitted with a towbar that is not recognised by the system.

Risk of false alarms or absence of warnings

If the system behaves abnormally contact an authorised dealer.

D r i v i n g - 2 1 7

ADDITIONAL DRIVING AID FUNCTIONS

Limitation of the system operation

– The radar area should be kept clean and free of any modifications in order to ensure the proper operation

of the system.

– Small objects moving close to the vehicle (motorcycles, bicycles, pedestrians, etc.) may not be recognised by the

system.

3

– When turning into a bend, the radars may temporarily cease to detect vehicles in adjacent lanes.

– The function may warn you late when two other vehicles are approaching from the rear, side by side in the adja-

cent lanes (driving on a 3-lane road) and at a much higher speed than your vehicle.

– The system may not provide a warning when the other vehicles are travelling at a significantly different speed.

– If the vehicle is being overtaken by a long vehicle (e.g. heavy goods vehicle overtaking at a similar speed to the ve-

hicle) the system may interrupt the warning before the end of the manoeuvre.

– The vehicle is travelling on a winding road.

2 1 8 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

Location of the camera 1

Activation/deactivation from

the multimedia screen 3

Safe distance alert

Make sure the windscreen is not ob-

scured (by dirt, mud, snow, conden-

sation etc.).

Location of the radar 2

3

Ensure that the radar area is not ob-

structed (by dirt, mud, snow, a badly

fitted front number plate etc.), im-

pacted, modified (including paint-

ing) or hidden by any accessory fit-

ted on the front of the vehicle (on the

grille or logo etc.).

This function is an ad-

ditional driving aid. This

function is not under

From the "Vehicle" world on your

multimedia screen 3 , press the "Dri-

ving assistance" menu then "Com-

fort".

Activate or deactivate the "Follow-

ing distance" function.

Using the information from the

radar 2 and camera 1 , this function

informs the driver of the time inter-

val between their vehicle and the ve-

hicle in front so that a safe stopping

distance between the two vehicles

can be maintained.

any circumstances in-

tended to replace the due care

and attention of the driver, who

should at all times be in control

of the vehicle.

The function is activated while the

vehicle speed is between about 19

mph and 93 mph or 105 mph (30 km/

h and 150 km/h or 170 km/h), depend-

ing on the vehicle.

Each time the vehicle is

started, the function con-

tinues the mode saved

the last time the engine was

stopped.

D r i v i n g - 2 1 9

ADDITIONAL DRIVING AID FUNCTIONS

– D (red): the time interval is less

Operation

than or equal to approximately one

second (very insufficient distance

between the two vehicles).

If the interval between the two vehi-

cles is less than approximately 0.5

second, the indicator light 4 on dis-

play D , will remain lit in red on the in-

strument panel.

3

Under certain conditions, the time

interval may not be displayed:

– while cornering;

– when changing lane;

– if the vehicle in front is sufficiently

far or outside the range of the radar

or camera.

With the function activated, the 4 in-

dicator is displayed on the instru-

ment panel and informs the driver of

the distance between their vehicle

and the vehicle in front.

– A (grey): function not operational;

– A (green): no vehicle detected;

– B (green): the time interval is

greater than or equal to approxi-

mately two seconds (distance be-

tween the two vehicles adapted to

your speed);

– C (yellow): the time interval is be-

tween approximately one and two

seconds (insufficient distance be-

tween the two vehicles);

2 2 0 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

Warnings

The measurement is displayed for information: the system does not carry out any action on the vehicle.

This function is not designed for use in urban conditions or for a dynamic driving style (sudden cornering,

acceleration, braking, etc.), but rather for stable driving conditions.

3

The function does not interact with the braking system.

The radar and camera zones must be kept clean and free of any tampering in order to ensure the proper operation

of the system.

Any work carried out in the area where the radar or camera is located (repairs, replacements, windscreen and/or

bumper modifications, etc.) must be carried out by a qualified professional.

D r i v i n g - 2 2 1

ADDITIONAL DRIVING AID FUNCTIONS

This function is an additional driving aid. This function is not under any circumstances intended to replace

the due care and attention of the driver, who should at all times be in control of the vehicle.

System servicing/repairs

– In the event of an impact, the radar and/or camera alignment may be changed and its operation may conse-

quently be affected. Deactivate the function and consult an authorised dealer.

– Any work carried out in the area where the radar and/or camera is located (replacements, repairs, windscreen

and/or bumper modifications, etc.) must be carried out by a qualified professional.

3

Only an authorised dealer is qualified to service the system.

In the event of system disturbance

– obstruction of the windscreen or the bumper (by dirt, ice, snow, condensation etc.);

– a complex environment (metal bridge, tunnel, etc.);

– poor weather conditions (snow, hail, black ice, etc.);

– poor visibility (night, fog, etc.);

– poor contrast between the vehicle preceding it and the surrounding area (e.g. white vehicle in a snowy area, etc.);

– being dazzled (glaring sun, lights of vehicles travelling in the opposite direction; etc.);

– the road is narrow, winding and undulating (tight bends etc.)

Risk of erroneous false alarms.

2 2 2 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

– and stationary vehicles;

or

– surrounding pedestrians and cy-

clists.

This system can apply

maximum braking to the

vehicle until it is com-

Active emergency braking

pletely stationary if necessary.

For safety reasons, always wear

your seat belt when travelling in

your vehicle and make sure that

it is loaded so that no items can

be thrown forward and hit the

occupants.

The system informs the driver if

there is a risk of head-on collision to

enable appropriate emergency ma-

noeuvres (pressing the brake pedal

and/or turning the steering wheel).

Depending on the reactivity of the

driver, the system can assist with

braking in order to limit damage or

prevent a collision.

3

Location of the camera 1

The system is otherwise inactive

and does not trigger an alert.

Make sure the windscreen is not ob-

scured (by dirt, mud, snow, conden-

sation etc.).

This function is an ad-

ditional driving aid.

This function is not un-

Using information from the camera

1 and the radar 2 , the system deter-

mines the distance between your

vehicle:

– from the vehicle ahead in the

same lane;

Location of the radar 2

Make sure that the area around the

radar is not obscured (by dirt, mud,

snow or an incorrectly fitted number

plate), impacted, altered (including

paintwork) or hidden.

der any circumstances

intended to replace the due

care and attention of the driver,

who should at all times be in

control of the vehicle.

or

– from any oncoming vehicles in the

context of a manoeuvre to change

direction;

Operation

When driving, when there is a risk of

collision, the system:

or

– and vehicles passing perpendicu-

– alerts you of a collision risk: the

"Detected obstacle" message ap-

pears on the instrument panel ac-

companied by a beep.

larly;

or

D r i v i n g - 2 2 3

ADDITIONAL DRIVING AID FUNCTIONS

Note: if the driver presses the brake

pedal and the system still detects a

risk of collision, the braking force

may be increased if it is not suffi-

cient to prevent the collision.

– can trigger braking: if the driver

does not react to the alert and the

collision becomes imminent, the red

Detection of oncoming vehicles in

the context of a manoeuvre to

change direction

In the event of an emer-

gency manoeuvre, you

can stop the braking at

any moment by:

– tapping the accelerator ped-

3

al;

or

warning light

and the "Brake"

– turning the steering wheel as

a collision avoidance manoeu-

vre.

message are displayed on the in-

strument panel accompanied by a

sound signal.

Note:

– if the driver uses the vehicle con-

trols (steering wheel, pedals, etc.)

the system may delay its reaction or

not activate;

– if active emergency braking has

caused the vehicle to stop, the vehi-

cle is kept stationary for a short

time. Beyond this time limit, the dri-

ver must keep the vehicle stationary

by holding their foot on the brake

pedal;

Special features of warn-

ings

Depending on the speed,

the warning and braking may

be activated simultaneously.

When you wish to change direction

(e.g. A ), oncoming vehicles are de-

tected by the system when:

– your vehicle is travelling at a

speed between approximately 5

mph (8 km/h) to 12 mph (20 km/h);

– you have activated the direction

indicator light.

Detection of vehicles crossing the

lane perpendicularly

Vehicles crossing the lane perpen-

dicularly are detected by the system

when:

Vehicle detection

Detection of vehicles travelling in

the same lane

A risk of a collision with the vehicle in

front of you in the same lane is de-

tectable by the system when the ve-

hicle is travelling at a speed over ap-

proximately 5 mph (8 km/h).

– after the system activates brak-

ing, the "Advanced Safety trig-

gered" message will be displayed

2 2 4 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

– your vehicle is travelling at a

speed between approximately 12

mph (20 km/h) and 37 mph (60 km/h).

Detection of vehicles stopped in the

lane

Stationary vehicles are detected by

the system when:

– your vehicle is travelling at a

speed between approximately 5

mph (8 km/h) and 50 mph (80 km/h).

Activation/deactivation

Depending on the vehicle,

according to the length of

time following the last

time the engine was stopped,

the function is reactivated:

3

– when the vehicle is unlocked;

or

– when a door is opened;

or

Detection of pedestrians and cy-

clists

Detection of pedestrians and cy-

clists in the same lane

The system detects pedestrians and

cyclists when:

– your vehicle is travelling at a

speed between approximately 5

mph (8 km/h) and 53 mph (85 km/h).

Detection of pedestrians and cy-

clists when changing direction

– when the engine is restarted.

To activate or deactivate the func-

tion, refer to the multimedia instruc-

tions.

Activating, deactivating the system

from the multimedia screen 3

Select "ON" or "OFF".

Settings

For safety reasons, car-

ry out any adjustments

while the vehicle is sta-

tionary.

The system detects pedestrians and

cyclists when:

– your vehicle is travelling at a

speed between approximately 5

mph (8 km/h) and 12 mph (20 km/h).

Settings from the multimedia screen

3

D r i v i n g - 2 2 5

ADDITIONAL DRIVING AID FUNCTIONS

warning light appears on the instru-

ment panel.

The possible causes are:

– the system is temporarily blinded

(glare from the sun, dipped beam

headlights, bad weather conditions

etc.). The system will be operational

again when visibility conditions are

better;

3

– the system is temporarily inter-

rupted (e.g. the windscreen, front or

rear bumper or logo is obscured by

dirt, mud, snow, condensation, etc.)

In this case, park the vehicle and

switch off the engine. Clean the

windscreen, the front bumper or the

logo. The next time the engine is

started, after around five or ten min-

utes of driving, the warning light and

the message disappear. If this is not

the case, this may arise from anoth-

er cause; contact an approved deal-

er.

With the vehicle stationary, to ac-

cess the function settings from the

multimedia screen 3 , refer to the

multimedia instructions:

"Warning": adjust the sensitivity lev-

el. To do this select:

– « Late » ;

– « Standard » ;

– « Early ».

Operating faults

Please refer to the multimedia in-

structions for more information.

If the system detects a temporary

fault the

warning light, or de-

Temporarily not available

pending on the vehicle, the

warning light appears on the instru-

ment panel. Consult an approved

Dealer.

If the system detects a temporary

fault the

warning light, or de-

pending on the vehicle, the

2 2 6 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

Warnings

This function is an additional driving aid. This function is not under any circumstances intended to replace

the due care and attention of the driver, who should at all times be in control of the vehicle.

The triggering of this function may be delayed or prevented when the system detects clear signs of control

of the vehicle by the driver (action on the steering wheel, pedals etc.).

3

The system cannot be activated when:

– the gear control is in Neutral position;

– the Electronic Stability Control (ESC) has been triggered.

System servicing/repairs

In the event of an impact, the radar and/or camera alignment may be changed and its operation may conse-

quently be affected.

–

Deactivate the function and consult an authorised dealer.

Any work in the area where the radar and/or camera is located (repairs, replacements, windscreen modifications,

etc.) must be carried out by a qualified professional.

–

Only an authorised dealer is qualified to service the system.

D r i v i n g - 2 2 7

ADDITIONAL DRIVING AID FUNCTIONS

System disturbance

Some conditions can disturb or damage the system's operation, such as:

– a complex environment (metal bridge, tunnel, etc.);

– poor weather conditions (snow, rain, hail, black ice, etc.);

– poor visibility (night, fog, etc.);

– poor contrast between the object (vehicle, pedestrian etc.) and the surrounding area (e.g. pedestrian dressed in

white located in a snowy area etc.);

3

– being dazzled (glaring sun, lights of vehicles travelling in the opposite direction; etc.);

– windscreen obscured (by dirt, ice, snow, condensation etc.);

– ...

In these conditions, the system may not react, may warn the driver or may brake inadvertently.

Limitation of the system operation

– Each time the vehicle is started, the system carries out a calibration according to the vehicle surroundings and

may be inactive for a length of time between approximately two to five minutes of driving;

– the radar and camera zones must be kept clean and free of any modifications in order to ensure the proper opera-

tion of the system;

– the system may not respond to small vehicles such as motorbikes as effectively as to other vehicles;

– the system may not operate properly when the road surface is slippery (rain, snow, black ice, etc.);

– to ensure correct operation, the system needs to distinguish the entire obstacle. So the system cannot detect:

– pedestrians/cyclists in the darkness or in poor lighting conditions;

– partially visible pedestrians/cyclists;

– pedestrians less than approximately 80 cm;

– pedestrians carrying large objects;

– ...

In these conditions, the system may not react, may warn the driver or may brake inadvertently.

2 2 8 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

Deactivating the function

You must deactivate the function if:

– the camera area has been damaged (e.g. on the inside or outside of the windscreen);

– the front of the vehicle has been damaged (impact, distortion, scratch on the radar, etc.);

– the vehicle is being towed (breakdowns);

– the windscreen is cracked or distorted (do not carry out windscreen repairs in this area; have it changed by an ap-

proved dealer);

3

– you are not driving on a paved road.

In the event of the system behaving abnormally, deactivate it and contact an authorised dealer.

Halting the function

You can halt the active braking function at any time by tapping the accelerator pedal or by turning the steering

wheel in a collision avoidance manoeuvre.

D r i v i n g - 2 2 9

ADDITIONAL DRIVING AID FUNCTIONS

and issues a new warning if neces-

sary.

Operation

Driver vigilance warning

The driver vigilance warning is a

function that analyses the behav-

iour of the driver (driving style, vehi-

cle steering, etc.) and alerts them if

there is a risk of falling asleep.

It takes into account indicators such

as:

– steering wheel movements;

– driver actions on other systems

(indicators, brake pedal, etc.).

The driver vigilance warn-

ing constantly monitors

the driver's attention and

can provide several warnings

per journey.

3

The system resets every time

the engine is started.

Activation/deactivation

This function is an ad-

ditional driving aid in

case of risk of fatigue.

The function does not

For safety reasons, car-

ry out any adjustments

while the vehicle is sta-

tionary.

The function is set to notify the dri-

ver if:

operate on the vehicle. The

function cannot, under any cir-

cumstances, replace the

driver's responsibility during dri-

ving.

The driver must always adapt

their driving according to their

alertness, regardless of the

system's indications.

– a few minutes have elapsed since

the vehicle last stopped;

– the vehicle speed is greater than

approximately 43 mph (70 km/h).

If there is a risk of fatigue or im-

paired attention, the "Vigilance alert

Have a break" 1 message is dis-

played on the instrument panel, ac-

companied by a beep.

Press switch 2 OK to delete the

warning.

After deleting the message, the sys-

tem continues vigilance monitoring

2 3 0 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

– To reactivate the alerts, press the

button 3 once. The indicator light on

the button 3 lights up.

Depending on the vehicle,

depending on the length

of time following the last

Depending on the vehicle,

it may not be possible to

deactivate alerts.

Activating and deactivating the

alerts from the multimedia

screen 4

time the engine was stopped,

the alerts are reactivated:

3

Activating and deactivating

alerts using the "My Safety" but-

ton 3

– when the vehicle is unlocked;

or

– when a door is opened;

or

– when the engine is started.

When the alerts are deac-

tivated, the system con-

tinues to assess the

driver's state of fatigue.

To activate or deactivate the alerts,

please refer to the multimedia in-

structions.

Depending on the vehicle,

alerts are automatically

deactivated when the

The alerts can be deactivated or ac-

tivated using "Perso" mode in the

"My Safety" function ꢀ 198.

If the alerts have previously been de-

activated using Perso mode:

– to deactivate the alerts, press the

button 3 twice. The indicator light on

the button 3 goes out;

Select "ON" or "OFF".

"Lane Centring" function is acti-

vated. To re-activate the warn-

ings, the "Lane Centring" func-

tion must be deactivated. For

more information ꢀ 261.

Limitations of system operation

Some conditions can disrupt or

damage the system operation, for

example:

D r i v i n g - 2 3 1

ADDITIONAL DRIVING AID FUNCTIONS

– certain driving styles (incorrect

Once the speed limiter is activated,

you can adapt the limited speed set-

point to the speed limit displayed on

the instrument panel by the system

(ꢀ 240).

If the detected speed limit is exceed-

ed, the road sign displayed on the in-

strument panel is modified to inform

the driver.

Detection of road signs

driving etc.);

– driving on a road in poor condition;

– strong side wind;

Introduction

– The clock is wrongly configured

(depending on vehicle);

– winding roads;

3

– trailer traction.

Operating faults

Location of the camera 1

If the system detects a fault, the

"Check Fatigue Warning System"

Make sure the windscreen is not ob-

scured (by dirt, mud, snow, conden-

sation etc.).

message and the

warning

light are displayed on the instrument

panel.

Have the system checked by an au-

thorised dealer.

Special features

For vehicles with a map subscrip-

tion:

The system displays speed limits on

the instrument panel according to

road signs detected on the side of

the road.

It mainly uses information taken

from the camera 1 attached to the

windscreen behind the rear view

mirror. Depending on the country,

the system also uses information

from a map subscription to interpret

certain signs (town entrance, etc.).

– if the vehicle is travelling in a coun-

try where the speed units differ from

those of the vehicle, the system dis-

plays the speed limit sign in the unit

of the country, alongside the speed

limit converted to the unit used by

the vehicle’s instrument panel.

– for countries where the speed limit

is reduced during rainy weather on

some types of roads, the system

may alter the detected speed limit

after a few seconds of the wind-

screen wipers being activated.

The sign displayed on the instru-

ment panel changes when a road

sign is detected by the system.

For vehicles without a map subscrip-

tion: when driving in a country where

2 3 2 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

speed units differ from those on your

vehicle, you can manually select the

speed unit shown on the instrument

panel (e.g. change the unit from

miles to kilometres) in order to dis-

play relevant information ꢀ 135.

Note: the system does not take into

account exceptional speed limit

measures, such as peak pollution

days.

van, speed limit with length of appli-

Activation/deactivation

For safety reasons, car-

cation, etc.)

3. Additional road signs (start of no

overtaking zone).

ry out any adjustments

while the vehicle is sta-

tionary.

If the detected speed limit is exceed-

ed, a circle flashes around the road

sign (warning light 2 ) accompanied,

depending on the vehicle, by a beep

emitted for a few seconds to warn

you.

It remains illuminated on the instru-

ment panel as long as the vehicle is

exceeding the detected speed limit.

3

Depending on the length

of time following the last

time the engine was

Operation

stopped, the sound alert is reac-

tivated:

Map subscription

Road sign detection is as-

sociated with a map sub-

scription.

To manage the subscription,

please refer to the multimedia

instructions.

– when the vehicle is unlocked;

or

– when a door is opened;

or

– when the engine is restarted.

If there is no subscription, the

system will be limited to taking

into account the speed limit

signs when they are detected

by the camera.

The system will no longer take

into account information relat-

ed to the maps. The speed limit

availability may be affected.

Warning lights

The function displays the following

warning lights:

2. Speed limit signs and additional

speed limit signs (speed on exit

ramp with arrow, speed with a cara-

D r i v i n g - 2 3 3

ADDITIONAL DRIVING AID FUNCTIONS

Activating, deactivating the

overspeed sound alert using the

"My Safety" button 4

Activating, deactivating the

overspeed sound alert from the

multimedia screen 5

3

To adapt the speed limiter or adap-

tive cruise control setpoint to the de-

tected speed limits: briefly press

switch 6 to adjust the vehicle's

speed to the speed limit indicated

on the last detected speed limit sign;

Note: on vehicles with a map sub-

scription, you can automatically ad-

just the vehicle's speed to each new

limit indicated on the detected

speed limit signs. To do this, press

and hold switch 6 for approximately

two seconds.

The sound alert can be deactivated

or activated using "Perso" mode in

the "My Safety" function ꢀ 198.

If the sound alert has previously

been deactivated using "Perso"

mode:

– to deactivate the sound alert,

press the button 4 twice. The indica-

tor light on the button 4 goes out;

– to reactivate the sound alert,

press the button 4 once. The indica-

tor light on the button 4 lights up.

To activate or deactivate the sound

alert, please refer to the multimedia

instructions.

Select ON or OFF.

Variation of the limited speed or

cruising speed

(depending on the vehicle)

Temporary unavailability

If the system is unavailable for rea-

sons related to the camera or map

2 3 4 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

or

data, the

symbol or, depend-

symbol

– « Check Front camera » ;

or

ing on the vehicle, the

is displayed on the instrument panel.

If there is still a problem, contact an

approved dealer.

The system cannot detect the speed

limit if:

– « Check Driving assist ».

Consult an approved Dealer.

3

– the windscreen is not clean;

– the camera is blinded by the sun;

– there is insufficient visibility (fog,

etc.);

– the signs are not legible (snow,

etc.) or are hidden (by another vehi-

cle or by trees);

– map information is not up to date.

Note: when the front camera is ob-

scured, the message "Front camera

no visibility" appears on the instru-

ment panel. Clean the windscreen

area in front of the camera.

Operating faults

When the system detects an operat-

ing fault, the

or, depending on

the vehicle,

symbol is dis-

played on the instrument panel.

In some cases, they are accompa-

nied by the following message:

– « Driving assist unavailable » ;

D r i v i n g - 2 3 5

ADDITIONAL DRIVING AID FUNCTIONS

Warnings

This function is an additional driving aid. This function is not under any circumstances intended to replace

the due care and attention of the driver, who should at all times be in control of the vehicle.

The driver must always adapt their speed to the highway code and traffic conditions, regardless of system

indications.

3

The system may not detect all speed limit signs or may interpret them incorrectly.

The driver must not ignore road signs undetected by the system and should give priority to complying with the actu-

al road signs and the highway code.

In the event of poor visibility (fog, snow, frost, etc.), it is possible that the system may not indicate the correct speed

to the driver.

2 3 6 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

Operation

Active emergency braking in

reverse gear

This function is an ad-

ditional driving aid. This

function is not under

any circumstances in-

tended to replace the due care

and attention of the driver, who

should at all times be in control

of the vehicle.

3

An impact to the un-

derside of the vehicle

while manoeuvring

(e.g. striking a post,

Fixed rear obstacle detection

raised kerb or other street furni-

ture) may result in damage to

the vehicle (e.g. deformation of

an axle).

To avoid any risk of accident,

have your vehicle checked by

an approved Dealer.

When in reverse gear and moving at

between approximately 2 mph and 6

mph (3 km/h and 10 km/h), if there is

a risk of collision with a fixed obsta-

cle, the system automatically

In addition to the "Parking assis-

tance" ꢀ 287 function and using in-

formation from the four central sen-

sors located at the rear of the vehi-

cle, the system detects fixed obsta-

cles located behind your vehicle. If

there is a significant risk of collision,

the system automatically causes

the vehicle to brake.

brakes the vehicle. Visual feedback

2

is displayed on the multime-

dia screen 1 , accompanied by a

beep.

Once the vehicle has stopped, the

vehicle must be held stationary by

the driver keeping their foot on the

brake pedal.

Note: make sure that the four cen-

tral sensors located at the rear of

the vehicle are not obscured (by dirt,

mud, snow, etc.).

D r i v i n g - 2 3 7

ADDITIONAL DRIVING AID FUNCTIONS

If the vehicle is fitted with a towbar

recognised by the system and a

trailer has been connected, active

emergency braking in reverse gear

is automatically deactivated and

the following message is displayed

on the instrument panel: "Trailer:

parking sensors unavailable", ac-

Activating or deactivating the

system

The 3

warning light is dis-

played on the multimedia screen ac-

companied by, depending on the

type of malfunction, the following

message on the instrument panel:

– « Parking sensors unavailable » ;

or

3

– « Check Parking sensors » ;

companied by the 3

warning

light on the multimedia screen.

or

– « Driving assist unavailable » ;

or

– « Check Driving assist ».

Clean the ultrasonic sensors. If there

is still a problem, contact an ap-

proved dealer.

To activate or deactivate the func-

tion via the multimedia screen 1 , se-

lect the "Vehicle" world, then "Park-

ing assistance". Select "Rear Active

Emergency Braking".

If the function is deactivated, the 3

warning light is displayed on

the multimedia screen.

Operating faults

When the system detects an operat-

ing fault, active emergency braking

in reverse gear is automatically de-

activated.

2 3 8 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

Warnings

Active emergency braking in reverse gear

This function is an additional driving aid. This function cannot, under any circumstances, replace the vigi-

lance and responsibility of the driver.

3

Some climatic and environmental conditions can disrupt or damage the system. As a consequence, the dri-

ver should always be ready for sudden incidents while driving: always ensure that there are no small, narrow moving

obstacles (such as a child, animal, pushchair, bicycle, stone, post, etc.) in the blind spot when manoeuvring.

The triggering of this function may be delayed or prevented when the system detects clear signs of control of the

vehicle by the driver (action on the steering wheel, pedals etc.).

System servicing/repairs

– In the event of an impact, the rear sensors and their performances may be affected. Deactivate the function and

consult an authorised dealer.

– Any work in the area where the sensors are located (repairs, replacements, bumper modifications etc.) must be

carried out by a qualified professional.

Only an authorised dealer is qualified to service the system.

Deactivating the function

You must deactivate the function if the vehicle is being towed (breakdown recovery) or if the vehicle is fitted with a

towbar that is not recognised by the system.

In the event of the system behaving abnormally, deactivate it and consult an authorised dealer.

D r i v i n g - 2 3 9

Driving -> Additional driving aid functions for Your Renault Scenic 4 Door Fifth Generation (2023-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals