Get Driving -> Stop and Go adaptive cruise control Guide for Renault Scenic 4 Door Fifth Generation (2023-2026)

STOP AND GO ADAPTIVE CRUISE CONTROL

tions (ground relief, weather condi-

tions, etc.).

The regenerative braking

system and the paddles

are not available when

Introduction

The Stop and Go adaptive cruise

control function can be activated

while the vehicle is travelling at be-

tween 0 mph and 93 mph or 105 mph

(0 km/h and 150 km/h or 170 km/h)

according to road conditions (traf-

fic, weather, etc.).

Based on information from a radar

or camera, the Stop and Go adaptive

cruise control function gives you the

option of maintaining a selected

speed, known as the cruising speed,

while keeping a safe distance from

the vehicle in front in the same lane.

Depending on the vehicle, when the

"Road Sign Detection" function is

activated ꢀ 232, the system can

adapt the speed of your vehicle ac-

cording to the speed limit signs rec-

ognized by the camera.

Depending on the country and sub-

scription, the system will use the

camera and the map to adjust the

vehicle speed in advance according

to the context and road incidents

(roundabouts, bends, upcoming

road signs or speed limit zones).

the adaptive cruise control

function is activated.

3

The Stop and Go adaptive

cruise control does not

trigger an emergency

stop and its braking capability

is limited.

The function is indicated by the

symbol.

Note:

– the driver must observe the maxi-

mum speed limit and safe distances

according to the legislation in the

country where they are driving;

– the adaptive cruise control can

brake the vehicle up to around a

third of the braking capacity. De-

pending on the situation, the driver

may need to brake harder.

If the vehicle in front stops, the Stop

and Go adaptive cruise control may

brake your vehicle to a complete

stop before setting off again.

The system controls acceleration

and deceleration of your vehicle us-

ing the engine and braking system.

While ECO mode is acti-

vated, the cruising speed

cannot exceed the maxi-

mum ECO ꢀ 185 mode speed.

The system's maximum range is ap-

proximately 130 metres. This may

vary according to the road condi-

2 4 4 - D r i v i n g

STOP AND GO ADAPTIVE CRUISE CONTROL

Location of the camera 1

Controls

This function is an ad-

ditional driving aid.

Control A

It can under no circum-

stances replace the

driver's responsibility to respect

speed limits and safe distances

or to be vigilant.

3

The driver must always be in

control of the vehicle.

The driver must always adapt

their speed according to the

surroundings and traffic condi-

tions.

Use the Stop and Go adaptive

cruise control function outside

built-up areas, on wide roads

with visible lines.

The cruise control may have

limited operation on very wind-

ing or slippery roads (black ice,

aquaplaning, gravel) or during

bad weather (fog, rain, side

winds, etc.)

Make sure the windscreen is not ob-

scured (by dirt, mud, snow, etc.).

3. Switch for selecting/deselecting

the driving aids, depending on the

vehicle:

Location of the radar 2

Ensure that the radar protection

plate is not obstructed (dirt, mud,

snow, a badly fitted number plate),

impacted, modified (including paint-

ing) or hidden by any accessory fit-

ted on the front of the vehicle (on the

grille or logo, etc.).

– Active Driver Assist;

– adaptive cruise control;

– speed limiter;

– OFF.

There is a risk of accidents.

4. Put the function on standby (with

cruising speed stored) (0).

5. Recall the stored cruising speed

(RES).

6.

D r i v i n g - 2 4 5

STOP AND GO ADAPTIVE CRUISE CONTROL

–

Upwards: activates, increases

cruising speed or stores the current

speed (SET/+).

The radar and camera

zones must be kept

clean and free of any

tampering in order to

ensure the proper operation of

the system.

Important: you should

keep your feet near the

pedals at all times to

prepare for any event.

– Downwards: activates, decreases

cruising speed or stores the current

speed (SET/-).

3

7. Pop-up button (depending on the

vehicle): adapts the speed setpoint

Switching on

to detected speed limits

ꢀ 232

Control A

Displays

8. Adjusting the following distance.

Depending on the vehicle,

you can link the cruise

control function to the

"Road sign detection" function

ꢀ 232 by pressing the switch 7 .

If the "OFF" mode is selected before

switching off the engine, the "Speed

limiter" function will be activated by

default the next time the engine is

started.

Press switch 3 as many times as

necessary to select adaptive cruise

control. The warning light 9 appears

in grey. The "Adaptive Cruise Control

ready: SET to activate" message ap-

pears on the instrument panel ac-

companied by dashes to indicate

that the cruise control function is in

9. Stop and Go adaptive cruise con-

trol warning light.

10. Stored cruising speed.

11. Vehicle in front.

12. Stored safe distance

2 4 6 - D r i v i n g

STOP AND GO ADAPTIVE CRUISE CONTROL

operation and waiting to store a

cruising speed.

This function cannot be activated

when:

– the parking brake is applied;

– the driver's seat belt is not fas-

tened;

– one or more doors are incorrectly

closed;

– the "Hands-free parking" function

is already activated.

The "Adaptive Cruise Ctl unavail-

able" message is displayed on the

instrument panel.

h), the "Invalid Speed" message is

displayed and the function remains

inactive.

If the vehicle is equipped with the

"Road Sign Detection" function

ꢀ 232, press the pop-up button 7 to

adapt the vehicle's speed to the

speed limits 13 detected by the cam-

era.

When passing the sign, the cruising

speed 10 adopts the value of the de-

tected speed 13 .

Once a cruising speed is memorised

and the cruise control function is ac-

tive, you may lift your foot off the ac-

celerator pedal.

Note: if your vehicle speed is lower

than about 19 mph (30 km/h), the

function uses a default cruising

speed of 19 mph (30 km/h). The vehi-

cle will accelerate until it reaches

the stored cruising speed.

3

Activating cruise control with

advance speed limit sign

recognition (display C )

Activating cruise control with

speed limit sign recognition

(display B )

Activating cruise control

Control A

When stationary or at a steady

speed, push the 6 upwards (SET/+)

or downwards (SET/-): the function is

activated and the current speed is

stored.

The minimum cruising speed is 19

mph (30 km/h).

The cruising speed 10 replaces the

dashes and cruise control is con-

firmed by the appearance of the

cruising speed in green and the

warning light 9 .

If you try to activate the function

above 96 mph (155 km/h) or, depend-

ing on the vehicle, 109 mph (175 km/

(depending on subscription)

Using the camera, the "Road sign

detection" function ꢀ 232 and the

map associated with the subscrip-

tion, the system anticipates the au-

(depending on the vehicle)

D r i v i n g - 2 4 7

STOP AND GO ADAPTIVE CRUISE CONTROL

tomatic adjustment of the vehicle

speed until the next sign is identified

14 .

– in some cases (if there is a signifi-

The detected speed 14 is taken into

account by the system. The vehicle

speed gradually adapts until it be-

comes the cruising speed 10 , with-

out any action taken by the driver.

The speed indicated at 14 is dis-

played at 13 when passing the

cant difference between the vehicle

speed and limited speed), the sys-

tem may request that you validate

the speed manually be pressing the

pop-up button 7 : the white square 16

is displayed around the indicated

speed to inform you.

Activation/deactivation

From the multimedia screen, in the

"Vehicle" World, select "Driving as-

sistance". Then, from the "Comfort"

menu, select "Speed limit adaptive

cruise control".

The letter "A" 15 is displayed on the

instrument panel to confirm the ac-

tivation of the cruise control with ad-

vance speed limit sign recognition.

3

speed limit sign or zone identified.

The driver must always stay vigilant

regarding the speed applied by the

system and remains responsible for

the vehicle speed.

When the function is not activated

or the subscription is no longer ac-

tive, the operation is identical to set-

ting the cruising speed with speed

limit sign recognition (display B ).

Cruise control with ad-

vance speed limit sign

recognition is associated

with a subscription. If there is no

subscription, this function can-

not be activated.

To manage the subscription,

please refer to the multimedia

instructions.

Operation

With the function activated, the fol-

lowing speeds are displayed on the

instrument panel:

– cruising speed 10 ;

– the current speed limit detected

by the system on the section of road

on which the vehicle is travelling 13 ;

– the speed detected by the system

on the next section of road or speed

limit zone 14 .

Note:

– you can also activate/deactivate

the function by pressing and holding

the pop-up button 7 ;

2 4 8 - D r i v i n g

STOP AND GO ADAPTIVE CRUISE CONTROL

The driver must always stay vigilant

Activating cruise control with

advance recognition of the

road layout (display D )

regarding the speed applied by the

system and remains responsible for

the vehicle speed.

Cruise control with ad-

vance recognition of the

road layout is associated

with a subscription.

Activation/deactivation

If there is no subscription, this

function cannot be activated.

To manage the subscription,

please refer to the multimedia

instructions.

3

From the multimedia screen, in the

"Vehicle" World, select "Driving as-

sistance". Then, from the "Comfort"

menu, select "Road layout adaptive

cruise control".

In the “Adaptive regulation” menu,

select “To road context”.

Controlling cruising speed

You can resume control of the vehi-

cle speed at any time by:

– putting the function on standby:

– by pressing the brake pedal;

– or by pressing the switch 4 (0);

When the function is not activated

or the subscription is no longer ac-

tive, operation is the same as setting

the cruising speed with speed limit

sign recognition (display B ) or, de-

pending on the subscription, setting

the cruising speed with advanced

speed limit sign recognition (display

C ).

(depending on subscription)

– by pressing the driving aids selec-

tion/deselection switch 3 .

Using the camera, the "Road sign

detection" function ꢀ 232 and the

maps associated to the subscrip-

tion, the system can anticipate and

manage the automatic adaptation

of the cruising speed 10 when the

vehicle approaches a roundabout or

a bend.

If the vehicle is approaching a bend

or roundabout, a warning light 17 ap-

pears on the instrument panel. The

vehicle adjusts its speed to a speed

appropriate to the feature detected.

The following symbols show the fea-

tures taken into account by the sys-

tem:

Control A

When automatically adapting the

speed to the signs and/or road lay-

out, it is possible to ignore these

events. Press the button 5 (RES) to

recall the stored cruising speed.

–

roundabout;

bend.

D r i v i n g - 2 4 9

STOP AND GO ADAPTIVE CRUISE CONTROL

– upwards (SET/+) to increase the

– distance gauge G : intermediate

distance 1 (corresponding to approx-

imately 1.6 second);

– distance gauge H : short distance

(corresponding to approximately 1.2

second).

The selected distance gauge ap-

pears in green on the instrument

panel. The other gauges remain in

grey.

Note: the distance must be set ac-

cording to the traffic level, local reg-

ulation and weather conditions.

Safe distance control activa-

tion

As soon as cruise control is activat-

ed, the default safe distance 12 is

displayed in green on the instrument

panel.

If the system detects a vehicle in

your lane, an outline of a vehicle 11

appears above the distance gauge

12 on the instrument panel.

Your vehicle adapts its speed to that

of the vehicle in front and applies

the brakes if necessary (the brake

lights come on) in order to maintain

the distance displayed on the instru-

ment panel.

speed.

Adjusting the following dis-

tance

You can vary the safe distance from

the vehicle in front at any time by

pressing switch 8 repeatedly.

3

The safe distance is ad-

justed by default on the

distance gauge G .

Note: the size of the outline 11 varies

according to the distance separat-

ing you from the vehicle in front. The

larger the outline, the closer the ve-

hicle in front.

Exceeding the cruising speed

The cruising speed may be exceed-

ed at any time by applying the accel-

erator pedal.

If it is exceeded, the cruising speed

10 appears in yellow.

If the driver presses the accelerator

pedal, the "Distance Control" func-

tion will no longer operate.

Setting the cruising speed

The horizontal distance gauge on

the instrument panel indicates the

various available safe distances:

– distance gauge E : long distance

(corresponding to approximately 2.4

seconds);

Control A

You can vary the cruising speed by

pressing repeatedly (for low varia-

tion) or pressing and holding (for

high variation) on the control 6 :

– distance gauge F : intermediate

distance 2 (corresponding to ap-

proximately 2 seconds);

Then, release the accelerator pedal:

the cruise control and safe distance

control will automatically resume

– downwards: (SET/-) to decrease

the speed;

2 5 0 - D r i v i n g

STOP AND GO ADAPTIVE CRUISE CONTROL

the speed and distance instructions

that you had previously selected.

– if the stopping time exceeds ap-

– you open one of the opening ele-

ments;

– you press the engine start/stop

button;

proximately thirty seconds, for the

vehicle to set off again it is neces-

sary to either:

–

Overtaking manoeuvre

– the slope is too steep;

– certain driving aids and correction

devices are triggered (active emer-

gency braking,ABS, ESC, etc.)

Note: Depending on the vehicle, if

the reception of the connected data

is not optimal, the system automati-

cally switches on standby the ad-

vance speed limit sign recognition

and/or advance recognition of the

road layout functions.

The two functions are automatically

reactivated as soon as reception of

the connected data becomes opti-

mal again.

In all circumstances, the standby is

confirmed when the warning lights

appear in grey and the message

"Adaptive Cruise Control discon-

nected" appears on the instrument

panel.

If you want to overtake the vehicle in

front and your speed is over 43 mph

(70 km/h) only, activating the direc-

tion indicators temporarily reduces

the following distance and triggers

acceleration to facilitate overtaking.

– press the accelerator pedal;

– by pressing once on the button

5 (RES) on control A .

The message "Press RES or acceler-

ate to restart Cruise Control" ap-

pears on the instrument panel to

confirm.

If the stop exceeds around three

minutes, the electronic parking

brake is automatically applied and

the Stop and Go adaptive cruise

control is deactivated.

3

Stopping the vehicle and set-

ting off

If the vehicle in front slows down, the

system adapts its speed to bring the

vehicle to a complete stop if neces-

sary (e.g. in heavy traffic). The vehi-

cle stops a few metres from the vehi-

cle in front.

When the vehicle in front sets off

again:

– if the stop lasts for less than thirty

seconds, the vehicle will start again

without any action required from the

driver.

Note: the driver should always be

ready for sudden incidents while dri-

ving and remains responsible for

controlling the vehicle: if the system

detects a pedestrian in the area

around the vehicle, the automatic

restart will be inhibited until the next

stop;

The warning light 9 goes out to con-

firm that the function is deactivated.

Putting the function on stand-

by

You can set the function to standby

when:

– you press switch 4 (0);

– you apply the brake pedal while

the vehicle is moving.

The function is deactivated by the

system if:

– you set the gear control to P, R or

N;

– you unbuckle the driver's seat belt;

D r i v i n g - 2 5 1

STOP AND GO ADAPTIVE CRUISE CONTROL

the cruise control function without

or

taking into account the stored

speed: it is the speed at which the

vehicle is moving that is taken into

account.

Putting the Stop and

Go adaptive cruise

control in standby or

– the red alert K accompanied by

the message "Brake" if the situation

requires the driver's immediate at-

tention.

switching it off does

not cause a rapid reduction in

speed: you must brake by ap-

plying the brake pedal if neces-

sary.

In all situations, react accordingly

and perform the appropriate ma-

noeuvres.

"Take control of the vehicle"

warnings

3

Switching off the function

Exit from standby

Based on the stored cruising speed

If a speed is stored, it can be re-

called, once you are sure that the

road conditions are suitable (traffic,

road surface, weather conditions,

etc.). Press switch 5 (RES) within the

valid speed range.

When the stored speed is recalled,

activation of the cruise control is

confirmed by the illumination of the

cruising speed in green.

Note: if the stored speed is higher

than the current speed, the vehicle

will accelerate to reach that speed.

In some situations (e.g. coming upon

a much slower vehicle, vehicle in

front changing lanes quickly, etc.)

the system may not have time to re-

act.

The adaptive cruise control Stop

and Go function is interrupted:

Based on the current speed

– when you press the switch 3 for

control A .

The warning light 9 disappears from

the instrument panel to confirm that

the function has stopped.

Depending on the situation, the sys-

tem sounds a beep associated with:

– the orange alert J if the situation

requires the driver's attention;

Control A

When the cruise control is on stand-

by, press switch 6 upwards (SET/+)

or downwards (SET/-) to reactivate

2 5 2 - D r i v i n g

STOP AND GO ADAPTIVE CRUISE CONTROL

The radar is able to detect vehicles

In all cases, if the message is not

erased after the engine is restarted,

please contact an authorised deal-

er.

in front of your vehicle. The system

cannot operate correctly if the radar

detection area is obscured or if its

signal is disrupted.

To exit the driving assis-

tance, press switch 3 as

many times as necessary

until you reach OFF. The "Driving

Assistance deactivated" mes-

sage appears on the instrument

panel.

In this case, the next time the

engine is started, the "Speed

limiter" function will be activat-

ed and waiting for a speed limit

to be stored.

Temporary unavailability

(camera)

The system cannot operate if the

camera is obscured (by dirt, mud,

snow, condensation, etc.).

In the event of decreased visibility of

the camera, the performance of the

adaptive cruise control Stop and Go

will be reduced. Remain vigilant.

If the radar detection area is ob-

structed or the radar signal is dis-

rupted, the message "Front radar no

visibility" is displayed on the instru-

ment panel and the adaptive cruise

control Stop and Go is interrupted.

The green warning light 9 disap-

pears to confirm that the function

has been automatically deactivat-

ed.

3

Ensure that the radar area remains

clean and is not obstructed by snow,

mud, a badly fitted number plate or

by any accessory fitted on the front

of the vehicle (on the grille), or hid-

den by any accessory fitted on the

front of the vehicle (on the grille or

logo, etc.).

Conditions in certain geographical

areas may hinder the function, for

example:

– arid zones, tunnels, long bridges or

lightly used roads without road lines,

without signs or trees nearby;

– a military or airport zone.

Operating faults

Temporary unavailability

(radar)

If an adaptive cruise control func-

tion Stop and Go operating fault is

detected, the "Check adaptive

cruise control" message appears on

the instrument panel and the adap-

tive cruise control Stop and Go func-

tion is suspended.

If an operating fault is detected on

one or more components of the sys-

tem, the Stop and Go adaptive

cruise control function is deactivat-

ed.

Depending on the type of malfunc-

tion, the message is displayed on the

instrument panel:

You must leave such areas in order

for the function to work.

D r i v i n g - 2 5 3

STOP AND GO ADAPTIVE CRUISE CONTROL

– "Check Front camera", accompa-

nied, depending on the vehicle, by

Limitations of system opera-

tion

the warning light

– "Front radar to check", accompa-

nied, depending on the vehicle, by

;

Vehicle detection

3

the warning light

– "Check Camera/Radar", accom-

panied, depending on the vehicle, by

;

the warning light

;

– "Check vehicle" accompanied by

the warning light

.

Consult an approved dealer.

The system cannot detect:

– vehicles arriving at intersections:

slip road (example M ), etc.;

– vehicles driving on the wrong side

of the road or reversing towards you.

The system detects only vehicles

(cars, trucks, motorbikes) that are

moving in the same direction as your

vehicle.

A vehicle turning into the same lane

(example L ) will be taken into ac-

count by the system only once it en-

ters the camera and radar detection

areas.

The adaptive cruise con-

trol Stop and Go must be

used outside built-up ar-

eas, on wide roads with visible

lines.

The system may trigger inappropri-

ate or delayed braking.

2 5 4 - D r i v i n g

STOP AND GO ADAPTIVE CRUISE CONTROL

Detection during cornering

Detection of vehicles in adjacent

lanes

3

When entering a corner or bend, the

radar and/or camera may be tem-

porarily unable to detect the vehicle

in front (example N ).

The system may trigger an acceler-

ation.

The system may detect vehicles dri-

ving on an adjacent lane when:

– you drive into a bend (example P );

– you are driving on a road with nar-

row lanes;

– the speed of the vehicle on the ad-

jacent lane is slower and if one of

these vehicles is located too close to

the lane of the other.

The system may incorrectly trigger

vehicle slowing or braking.

When exiting a bend, the system's

detection of the vehicle in front may

be disrupted or delayed.

The system may trigger inappropri-

ate or delayed braking.

Vehicles hidden due to variations in

ground relief

D r i v i n g - 2 5 5

STOP AND GO ADAPTIVE CRUISE CONTROL

The system will not detect vehicles

hidden due to variations in ground

relief or those located outside of the

camera and radar detection areas

when driving uphill or downhill.

Vehicles outside the camera and

radar detection areas.

The system will react late or not at

all if the detected vehicles are out-

side the camera and radar detection

areas, particularly in the following

cases:

3

– vehicles transporting long objects

which exceed the line;

– the actual length of tall vehicles

(example Q ) is outside the radar de-

tection area (construction machine,

agricultural equipment towing vehi-

cle, etc.);

Stationary and slow moving vehi-

cles

When your speed is over approxi-

mately 31 mph (50 km/h), the system

does not detect:

– vehicles in front 18 that change

lane, or encountering a stationary

vehicle 19 (example T );

– stationary vehicles 20 , when you

change lane (example U ).

– vehicles insufficiently centred in

the lane;

– narrow vehicles which are very

close (example R ).

– stationary vehicles (example S );

– very slow moving vehicles.

When your speed is less than ap-

proximately 31 mph (50 km/h), the

system may not react or may react

very late to:

– stationary vehicles (example S );

– very slow moving vehicles;

2 5 6 - D r i v i n g

STOP AND GO ADAPTIVE CRUISE CONTROL

Detection of vehicles moving in-

to lane at high speed

3

Non-detection of fixed obstacles

and objects of a small size

The system cannot detect:

– pedestrians, bikes, scooters, etc.;

– animals;

– fixed obstacles (toll barriers, walls,

etc.) (example V ).

These are not taken into account by

the system. They do not trigger any

alert or reaction by the system.

Always be ready to re-

spond in all circum-

stances.

If your vehicle is overtaken by anoth-

er vehicle driving at high speed 21

(motorcycle, car, etc.) and the vehi-

cle is temporarily positioned be-

tween your vehicle and the vehicle in

front 22 , the system may trigger un-

due acceleration, slowing or brak-

ing.

The driver must always be in

control of the vehicle.

The Stop and Go adaptive

cruise control does not trigger

an emergency stop and its

braking capability is limited.

D r i v i n g - 2 5 7

STOP AND GO ADAPTIVE CRUISE CONTROL

Warnings

This function is an additional driving aid. It can under no circumstances replace the driver's responsibility to

respect speed limits and safe distances or to be vigilant.

3

The driver must always be in control of the vehicle.

Apart from the speed limit signs and road map information from the mapping (vehicles fitted with the

"Road sign detection" function and a subscription), other traffic information (traffic lights, pedestrian crossings,

etc.) is not taken into account by the system. The driver must always adapt their speed to the surroundings and dri-

ving conditions, regardless of system indications.

The system should under no circumstances be taken to be an obstacle detector or an anti-collision system.

Use the Stop and Go adaptive cruise control function outside built-up areas, on wide roads with visible lines.

System servicing/repairs

– In the event of an impact, the radar and/or camera alignment may be changed and its operation may conse-

quently be affected. Deactivate the system and consult an authorised dealer.

– Any work in the proximity of the radar and/or camera (replacements, repairs, windscreen modifications, paint-

work etc.) must be carried out by a qualified professional.

Only an authorised dealer is qualified to service the system.

2 5 8 - D r i v i n g

STOP AND GO ADAPTIVE CRUISE CONTROL

Deactivating the function

You must deactivate the function if:

– the vehicle is being towed (breakdowns);

– the vehicle is towing a trailer or a caravan;

– the vehicle is being driven in a tunnel or close to a metallic structure;

– the vehicle arrives at a toll point, a roadwork area or on a narrow lane;

– the vehicle is driven on a very winding road (mountain road, etc.);

– the vehicle is being driven up or down a very steep slope;

– the visibility is poor (glaring sun, fog, etc.);

3

– the vehicle is being driven on a slippery road surface (rain, snow, gravel, etc.);

– the weather conditions are poor (rain, snow, side winds, etc.);

– the radar area has been damaged (impacts, etc.);

– the camera area has been damaged (e.g. on the inside or outside of the windscreen);

– the windscreen is cracked or distorted.

In the event of the system behaving abnormally, deactivate it and contact an authorised dealer.

D r i v i n g - 2 5 9

STOP AND GO ADAPTIVE CRUISE CONTROL

In the event of system disturbance

Some conditions can disturb or damage the system's operation, such as:

– the windscreen or bumper is obscured in the radar area (by dirt, ice, snow, condensation, number plate,

etc.);

– a complex environment (tunnel, etc.);

– poor weather conditions (snow, heavy rain, hail, black ice, etc.);

– poor visibility (night, fog, etc.);

3

– being dazzled (glaring sun, lights of vehicles travelling in the opposite direction; etc.);

– narrow, winding or undulating road (tight bends, etc.);

– a vehicle with a significant difference in speed;

– use of mats not adapted to the vehicle. On the driver's side, only use mats suitable for the vehicle, attached with

the pre-fitted components, and check the fitting regularly. Do not lay one mat on top of another. There is a risk of

wedging the pedals.

In this case, the system may brake or accelerate unintentionally.

Many unforeseen situations may affect the system operation. Certain objects or vehicles that can appear in the

camera or radar detection zone may be interpreted by the system incorrectly, possibly leading to inappropriate ac-

celeration or braking.

You should always be attentive to sudden events that might occur while you are driving. Always keep your vehicle

under control by keeping your feet near the pedals, so that you are ready to act in any event.

2 6 0 - D r i v i n g

Driving -> Stop and Go adaptive cruise control for Your Renault Scenic 4 Door Fifth Generation (2023-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals