Get Driving -> Additional driving aid functions Guide for Renault Symbioz 4 Door First Generation (2024-2026)

ADDITIONAL DRIVING AID FUNCTIONS

To switch back to "All ON" mode,

press once on the button 1 . The indi-

cator light on the button 1 lights up.

"All on" mode

My Safety

Depending on the vehicle, the func-

tions and configurations of driving

assistance concerned are:

– overspeed sound alert ꢀ 217;

– lane departure prevention ꢀ 185;

– driver vigilance warning ꢀ 215;

– emergency lane departure pre-

vention ꢀ 192.

When the "All ON" mode is activat-

ed: the indicator light on the button 1

lights up and the "My Safety All ON

selected" message is displayed on

the instrument panel to confirm this.

The driving aids that are available in

the mode are activated.

The "My Safety" function can be

used to deactivate or activate a set

of driver assistance functions simul-

taneously.

Depending on the vehicle, you can

configure the "My Safety" function

from the multimedia screen by se-

lecting the driving aid functions to

be switched off as a group.

Depending on the length

of time following the last

time the engine was

3

stopped, the alerts are reacti-

vated:

– when the vehicle is unlocked;

or

Operation

– when a door is opened;

or

– when the engine is restarted.

"Custom" mode

You can use this mode to deactivate

or reactivate certain driving aids

that are available in the "All ON"

mode previously configured using

the "MY SAFETY PERSO" setting.

With the ignition on, press the switch

1 twice in quick succession. On the

first press, the "Press again for My

Safety Custom" message is dis-

played on the instrument panel. On

the second press, the warning light

on the switch 1 goes out. The "Cus-

tom" mode is activated. The "My

Safety Perso selected" message is

displayed on the instrument panel.

1 8 4 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

– performs corrective action on the

steering system.

Perso mode configuration

Lane departure prevention

From the multimedia screen 2

You can retake control of

the vehicle at any time by

operating the steering

wheel.

3

Location of camera 1

Make sure the windscreen is not ob-

scured (by dirt, mud, snow, conden-

sation etc.).

This function is an ad-

ditional driving aid. This

function is not under

Using information from the 1 cam-

era, the function triggers corrective

action on the vehicle steering sys-

tem when a continuous or broken

line is crossed or when approaching

the roadside (divider, barrier, pave-

ment, embankment, etc.) without

activating the direction indicator

lights.

Refer to the multimedia instructions

for information on accessing the

settings.

any circumstances in-

tended to replace the due care

and attention of the driver, who

should at all times be in control

of the vehicle.

Depending on the setting, in the

event of crossing a broken line with-

out activating the direction indica-

tor lights, the function:

– warns the driver without correc-

tive action on the steering system;

or

D r i v i n g - 1 8 5

ADDITIONAL DRIVING AID FUNCTIONS

Activation/deactivation

From the "My Safety" switch 3

Operation

From the multimedia screen 2

3

– To deactivate the function, if it has

been deactivated from the "Cus-

tom" mode of the "My Safety"

When the function is activated, the

or

and the left-hand and

Please refer to the multimedia in-

structions for more information.

right-hand line indicators 4 are dis-

played in grey on the instrument

panel.

ꢀ 184function, press switch 3 twice.

The

warning light is displayed

in yellow on the instrument panel.

– To reactivate the function, press

the 3 switch once. Warning light

The function is ready to alert or in-

tervene if the vehicle speed is over

approximately 40 mph (65 km/h)

comes on the instrument pan-

el.

and the

or

warning light

and the left-hand or right-hand line

indicators 4 are displayed in white.

The function is in operation if the ve-

hicle

– approaches a roadside without

activating direction indicators;

1 8 6 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

– crosses a continuous line without

activating the indicator lights;

– crosses a broken line without acti-

vating the direction indicators, if the

"operation on broken line" setting is

selected.

– by a vibration in the steering

wheel;

You can interrupt the tra-

jectory correction at any

time by moving the steer-

and

ing wheel.

– the

or

warning light

and the indicator 4 on the side of the

breached line turns to red on the in-

strument panel.

Note: on bends, the function allows

for slightly cutting the bend.

In these cases:

3

Vehicle fitted with "Active driver

assist" system

– the function triggers an action on

the vehicle's steering system to cor-

rect the vehicle trajectory;

If the "Lane centring" function is ac-

tivated at the same time as the

"Lane departure prevention" func-

tion, the display of the warning light

will vary as follows:

– the

or

warning light

Special cases

and the indicator 4 on the side of the

breached line changes to yellow on

the instrument panel.

If the corrective action on the steer-

ing system is not sufficient, the

"Keep control" Warning

– If the system is operating and

does not detect any activity on the

steering wheel, the "Keep control"

message appears on the instrument

panel accompanied by a beep and,

– the "Lane Centring" function is in

operation: the green

warning

light replaces the white or grey

or

warning light and the

indicator 4 on the side of the

or warning light on the

depending on the vehicle, the

warning light appears in yellow until

the driver has regained control of

the vehicle.

– If the system has been in opera-

tion for too long, the "Keep control"

message appears on the instrument

panel accompanied by a beep and

breached line change to red on the

instrument panel, accompanied by a

vibration on the steering wheel.

instrument panel. Thus, you are in-

formed as a priority of the status of

the function "Channel centriing";

– the "Lane Centring" function is put

on standby and the "Lane Departure

Prevention" function is neither ready

When the "Operation on broken line"

setting is not selected, the function

sounds the alarm if the vehicle

crosses a broken line without acti-

vating the indicator lights, and there

is no roadside close enough to the

line.

nor in operation: the grey

warning light replaces the white or

depending on the vehicle, the

warning light appears in yellow ac-

companied by the indicator 4 on the

side of the line concerned until the

driver has regained control of the

vehicle.

grey

or

warning light on

In this case, the function warns the

driver:

the instrument panel. Thus, you are

informed as a priority of the status

of the function "Channel centriing";

D r i v i n g - 1 8 7

ADDITIONAL DRIVING AID FUNCTIONS

– the "Lane Centring" function is put

on standby while the "Lane Depar-

ture Prevention" function is ready or

(160 km/h or 180 km/h), depending on

– a towbar is electrically connected

the vehicle;

to the trailer hitch socket;

– the lane width changes;

– operation of the electronic stabili-

ty control (ESC);

– the

warning light is dis-

in operation: the

or

played.

warning light is displayed in red or in

yellow on the instrument panel.

Thus, you are informed as a priority

of the status of the function "Lane

departure prevention".

In any case, you are informed at all

times of the status of the function

when it controls the steering system

of your vehicle. The most useful in-

formation is always displayed.

– operation of the anti-lock braking

system;

– the active emergency braking sys-

tem is triggered;

– intervention of another function

that controls the steering system,

such as the "Lane Centring" func-

tion.

When the function is deactivated,

3

the warning light is displayed

in yellow on the instrument panel.

Settings

If the function is unavailable, the

or

warning light and the

left-hand and right-hand correction

indicators 4 appear in grey on the in-

strument panel.

If the front camera is obscured, the

"Front camera without visibility"

message is displayed on the instru-

ment panel. Clean the area where

the sensors are located

Function temporarily unavail-

able/disabled

The system is temporarily unavail-

able or disabled when:

– very fast lane departure;

– driving continuously on a line;

– approximately four seconds after

changing lanes;

– tight bends;

– impaired visibility;

Automatic deactivation

– one of the direction indicators is

activated;

– activating the hazard warning

lights;

– engaging reverse gear;

– strong acceleration;

– the vehicle speed is greater than

approximately 99 mph or 112 mph

The function is automatically deac-

tivated when:

– the electronic stability control

(ESC) is deactivated or malfunc-

tions;

To access the multimedia screen

function settings 2 , refer to the mul-

timedia instructions:

– " Operation on broken line": use

this setting to select the response of

the function if the vehicle crosses a

– the anti-lock braking system is

malfunctioning;

1 8 8 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

broken line without activating the di-

rection indicators:

In some cases, they are accompa-

nied by the following message:

– « Driving assist unavailable » ;

or

– selected setting: the function

may trigger an action on the

vehicle's steering system to cor-

rect the vehicle trajectory;

– setting not selected: the func-

tion can warn the driver by means

of a vibration at the steering

wheel without correcting the vehi-

cle trajectory.

– « Check Front camera » ;

or

– « Check Driving assist ».

Consult an approved dealer.

3

– "Vibration": adjust the steering

wheel vibration for the "Lane depar-

ture prevention" function;

– "Lane exit anticipation": adjust the

line detection sensitivity level. To do

this, select:

– “Late”: line detected upon cross-

ing;

– “Standard”: line detected on ap-

proach;

– “Early” line detected nearby.

Please refer to the multimedia in-

structions for further information.

Operating faults

When the system detects an operat-

ing fault, the left-hand and right-

hand line indicators and the

warning light appear in yellow on the

instrument panel.

D r i v i n g - 1 8 9

ADDITIONAL DRIVING AID FUNCTIONS

Warnings

This function is an additional driving aid. This function is not under any circumstances intended to replace

the due care and attention of the driver, who should at all times be in control of the vehicle.

System servicing/repairs

3

– In the event of an impact, the camera alignment may be changed, and its operation may consequently be affect-

ed. Deactivate the function and consult an authorised dealer.

– Any work in the area where the camera is located (repairs, replacements, windscreen modifications etc.) must be

carried out by a qualified professional.

Only an authorised dealer is qualified to service the system.

In the event of system disturbance

Some conditions can disturb or damage the system's operation, such as:

– windscreen obscured (by dirt, ice, snow, condensation etc.);

– a complex environment (tunnel, etc.);

– poor weather conditions (snow, rain, hail, black ice, etc.);

– poor visibility (night, fog, etc.);

– multiple road markings (roadworks, etc.) ; the road lines are irregular or difficult to distinguish (e.g. partially erased

markings, excessive spacing, uneven road surface, etc.);

– being dazzled (glaring sun, lights of vehicles travelling in the opposite direction; etc.);

– the road is narrow, winding or undulating (tight bends, etc.);

– closely following a vehicle travelling in the same lane.

In this case, the "Lane departure prevention" function may be activated incorrectly or not at all.

Risk of unwanted, incorrect correction or no correction of trajectory.

Deactivating the function

You must deactivate the function if:

– the area of the camera has been damaged (on the windscreen side or the interior rear-view mirror side);

– the road is slippery (snow, black ice, aquaplaning, gravel etc.);

1 9 0 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

– the windscreen is cracked or distorted (do not carry out windscreen repairs in this area; have it changed by an ap-

proved dealer);

– the vehicle is towing a trailer or a caravan.

3

D r i v i n g - 1 9 1

ADDITIONAL DRIVING AID FUNCTIONS

Using information from the radar 2

and the camera 1 , the function trig-

gers corrective action on the vehicle

steering system in the event of a risk

of collision with a vehicle coming

from the opposite direction in the

adjacent lane, without the direction

indicator having been activated.

This system provides

an additional driving

aid.

Emergency lane departure

prevention

This system is not, un-

der any circumstances, intend-

ed to replace the due care and

attention of the driver, who

should at all times be in control

of the vehicle.

3

Depending on the vehicle, using in-

formation from the radars 3 and the

camera 1 , the function triggers cor-

rective action on the vehicle steer-

ing system in the event of a risk of

collision with a vehicle moving at the

same speed or at a higher speed, if

within the detection area of the rear

radars.

Location of the camera 1

Make sure the windscreen is not ob-

scured (by dirt, mud, snow, conden-

sation etc.).

Location of the front radar 2

You can retake control of

the vehicle at any time by

operating the steering

wheel.

Ensure that the radar area is not ob-

structed (dirt, mud, snow, a badly fit-

ted/attached front number plate),

impacted, modified (including paint-

work) or hidden by any accessory fit-

ted on the front of the vehicle (on the

front bumper, logo, etc.)

Location of the side radars 3

Ensure that the radar area is not ob-

structed (by dirt, mud, snow etc.), im-

pacted or modified (including paint-

work etc.).

1 9 2 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

Activating/deactivating the

function

Detection of an oncoming vehi-

cle

From the A "My Safety" switch

3

Please refer to the multimedia in-

structions for more information.

Press switch A twice if the function

has been disabled from the "Cus-

tom" mode of the "My Safety" func-

tion ꢀ 184.

To reactivate the function, press the

A switch.

From the B multimedia screen

D r i v i n g - 1 9 3

ADDITIONAL DRIVING AID FUNCTIONS

When driving at a speed between

approximately 40 mph (65 km/h)

and 68 mph (110 km/h), if there is a

risk of collision with a vehicle coming

from the opposite direction in an ad-

jacent lane and within the detection

zone C , without the direction indica-

tor having been activated, the sys-

tem:

–

triggers corrective action on the

steering system.

You can interrupt the tra-

jectory correction at any

time by moving the steer-

3

ing wheel.

–

warns you of a collision risk:

This function is an ad-

ditional driving aid.

This function is not un-

der any circumstances

intended to replace the due

care and attention of the driver,

who should at all times be in

control of the vehicle.

The function may not activate if the

approaching speed is greater than

approximately 124 mph (200 km/h)

(for example, you are travelling at 68

mph (110 km/h) and the vehicle is

travelling in the opposite direction in

the adjacent lane at 56 mph (91 km/

h).

The message "Risk of collision" is

displayed on the dashboard accom-

panied by the indicator 4 in red, the

line on the side of the intervention

and an audible signal. Display 5 ap-

pears on the instrument panel on the

side of the intervention;

If case of overtaking

(depending on the vehicle)

and

1 9 4 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

risk of collision with a vehicle locat-

hicle is detected in an adjacent

lane);

– activating the hazard warning

lights;

– strong acceleration;

– the vehicle speed is greater than

approximately 99 mph or 112 mph

(160 km/h or 180 km/h), depending on

the vehicle;

– the lane width changes;

– operation of the electronic stabili-

ty control (ESC);

– operation of the anti-lock braking

system;

– operation of the active emergency

braking system;

– ...

The system cannot be activated

when:

– the camera does not detect a line

(solid or broken) on the relevant side

of the vehicle;

– the camera does not simultane-

ously detect the two boundaries of

the lane in which your vehicle is mov-

ing;

– reverse gear is engaged;

– the field of vision of the camera is

obstructed;

ed in the blind spot D and it is mov-

ing in the same direction as your ve-

hicle or with a vehicle that is rapidly

approaching from behind in an adja-

cent lane that is in the detection

area E , the system:

3

–

warns you about a risk of collision:

the warning light 6 flashes, the mes-

sage "Lateral obstacle detected" is

displayed on the instrument panel,

accompanied by the indicator 4 in

red, the line on the side of the inter-

vention and an audible signal. Dis-

play 5 appears on the instrument

panel on the side of the intervention;

and

–

triggers corrective action on the

steering system.

Temporarily not available / non-

activation of the system

The system is temporarily unavail-

able or disabled when:

– very fast lane departure;

– driving continuously on a line;

– approximately four seconds after

changing lanes;

– tight bends;

– impaired visibility;

– activation of the direction indica-

tor light (only when an oncoming ve-

– the front radar is obscured;

– depending on the vehicle, the rear

radars are obscured;

While driving at a speed over 40 mph

(65 km/h), when approaching a line

(continuous or broken) and there is a

– ...

D r i v i n g - 1 9 5

ADDITIONAL DRIVING AID FUNCTIONS

Depending on the vehicle, if one of

the side radars is obscured the mes-

sage "Side radars no visibility" will

appear on the instrument panel.

When the front radar is obscured,

the "Front radar no visibility" mes-

sage is displayed on the instrument

panel.

When the front camera is obscured,

the "Front camera no visibility" mes-

sage is displayed on the instrument

panel.

Clean the area where the sensors

are located.

that the emergency lane departure

prevention function has been deac-

tivated.

If the vehicle is towing a trailer or

caravan, unexpected or unneces-

sary corrections may occur. You can

deactivate the system to avoid un-

expected or unnecessary correc-

tions.

3

Operating faults

When the function detects an oper-

ating fault, the following messages

may be displayed on the instrument

panel:

Automatically deactivating the

function

– « Check Front camera » ;

or

The system is automatically deacti-

vated when:

– the electronic stability control

(ESC) is deactivated or malfunc-

tions;

– the anti-lock braking system is

malfunctioning;

– A towbar is electrically connected

to the trailer hitch socket;

– « Front radar to check » ;

or

– « Check Driving assist » ;

or, depending on the vehicle,

– « Check Side radars ».

Consult an approved Dealer.

– the

warning light is dis-

played.

If the vehicle is equipped with a tow-

bar that is recognised by the system,

the message "Trailer: side radars un-

available" is displayed to inform you

1 9 6 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

Warnings

This function is an additional driving aid. This function is not under any circumstances intended to replace

the due care and attention of the driver, who should at all times be in control of the vehicle.

System servicing/repairs

3

– In the event of an impact, the alignment of the camera or radar(s) may be altered and its operation may conse-

quently be affected. Deactivate the function and consult an authorised dealer.

– Any work in the area where the camera or radars are located (replacements, repairs, windscreen modifications

etc.) must be carried out by a qualified professional.

Only an authorised dealer is qualified to service the system.

In the event of system disturbance

Some conditions can disturb or damage the system's operation, such as:

– windscreen obscured (by dirt, ice, snow, condensation etc.);

– a complex environment (tunnel, etc.);

– poor weather conditions (snow, rain, hail, black ice, etc.);

– poor visibility (night, fog, etc.);

– multiple road markings (roadworks, etc.) ; the road lines are irregular or difficult to distinguish (e.g. partially erased

markings, excessive spacing, uneven road surface, etc.);

– being dazzled (glaring sun, lights of vehicles travelling in the opposite direction; etc.);

– the road is narrow, winding or undulating (tight bends, etc.);

– closely following a vehicle travelling in the same lane.

In this case, the "lane departure prevention" function may be activated incorrectly or not at all.

Risk of unwanted, incorrect correction or no correction of trajectory.

Deactivating the function

You must deactivate the function if:

– the camera area (on the windscreen side or the interior rear-view mirror side) or radar area(s) have been dam-

aged;

– the road is slippery (snow, black ice, aquaplaning, gravel etc.) ;

D r i v i n g - 1 9 7

ADDITIONAL DRIVING AID FUNCTIONS

– the windscreen is cracked or distorted (do not carry out windscreen repairs in this area; have it changed by an ap-

proved dealer);

– the vehicle is towing a trailer or a caravan;

– the vehicle is being towed (breakdowns);

– you are not driving on a paved road.

3

1 9 8 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

Blind spot warning

The function does not no-

tify the driver if the other

vehicles are not moving.

3

This function is an ad-

ditional driving aid. This

function is not under

any circumstances in-

tended to replace the due care

and attention of the driver, who

should at all times be in control

of the vehicle.

Using information from the sensors

installed on each side of the rear

bumper (area C ), the function warns

the driver:

Special feature

– when a vehicle is in the blind spot

area A and travelling in the same di-

rection as your vehicle;

and/or

– when there is a risk of collision with

a vehicle that is in the B area and

driving faster than you on an adjoin-

ing lane.

The function warns you when your

vehicle is travelling at a speed above

approximately 9 mph (15 km/h).

D r i v i n g - 1 9 9

ADDITIONAL DRIVING AID FUNCTIONS

Ensure that zone C around the

radars on each side of the rear

bumper are not obstructed (by dirt,

mud, snow, etc.).

If one of the radars is obscured, the

"Side radars without visibility" mes-

sage is displayed on the instrument

panel. Clean the area where the sen-

sors are located.

– if you overtake another vehicle,

spot warning area and/or a vehicle

is rapidly approaching from the rear

on the side towards which you will

turn the wheel. If you cancel the di-

rection indicator, the function will re-

turn to the initial warning (display D ).

the warning light 2 will only come on,

if that vehicle remains for a long

enough period in your vehicle's blind

spot area A .

Display D

3

Conditions for non-function

– When driving on a road with tight

bends;

– in reverse.

Warning light 2

If the vehicle is equipped with a tow-

bar recognised by the system, the

"Trailer: blind spot warning off" mes-

sage is displayed on the instrument

panel to inform you that the function

is not operational. For information

on the range of equipment adapted

to your vehicle, we advise you to

consult an approved Dealer.

Operating faults

If the system detects a fault, the

"Check Side radars" message is dis-

played on the instrument panel.

First warning: direction indicator not

activated, the warning light 2 indi-

cates that a vehicle is detected in

the blind spot area and/or that a ve-

hicle is rapidly approaching from the

rear in an adjacent lane.

Consult an approved dealer.

A warning light 2 is located on each

door mirror 3 .

Note:

Display E

– clean the 3 rear view mirrors regu-

larly, so that the indicator lights 2

can be seen properly;

Direction indicator activated, the 2

warning light flashes when the func-

tion detects a vehicle in the blind

2 0 0 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

Due to the presence of

sensors behind the

bumper, it is advisable to

entrust any operation on the

bumper (repair, replacement,

paintwork, etc.) to a qualified

professional.

3

D r i v i n g - 2 0 1

ADDITIONAL DRIVING AID FUNCTIONS

Warnings

– The system’s detection range operates according to a standard lane width. If driving on a narrow lane,

the system may warn you when a vehicle is detected further away than the nearest lane.

– The system’s detection range operates according to a standard lane width. If you are driving in wide traf-

fic lanes, the system might not be able to detect a vehicle in the blind spot.

3

– In the event of very bad weather conditions (heavy rain, snow, etc.), the system may be temporarily disrupted. Re-

main aware of driving conditions.

There is a risk of accidents.

2 0 2 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

This function is an additional driving aid. This function is not under any circumstances intended to replace

the due care and attention of the driver, who should at all times be in control of the vehicle.

The driver should always adapt their speed to the traffic conditions, regardless of the system indications.

The system should under no circumstances be taken to be an obstacle detector or an anti-collision system.

System servicing/repairs

3

– In the event of an impact, radar alignment may be changed, and its operation will consequently be affected. Con-

sult an approved dealer.

– Any work in the area where the radars are located (repairs, replacements, etc.) must be carried out by a qualified

professional.

Only an authorised dealer is qualified to service the system.

System disturbance

Some conditions can disturb or damage the system's operation, such as:

– complex surroundings (metal bridges, tunnels, roads with barriers at the edge, etc.);

– poor weather conditions (snow, hail, black ice etc.) ;

– the vehicle is fitted with a towbar that is not recognised by the system.

Risk of false alarms or absence of warnings

If the system behaves abnormally contact an authorised dealer.

D r i v i n g - 2 0 3

ADDITIONAL DRIVING AID FUNCTIONS

Limitation of the system operation

– The radar area should be kept clean and free of any modifications in order to ensure the proper operation

of the system.

– Small objects moving close to the vehicle (motorcycles, bicycles, pedestrians, etc.) may not be recognised by the

system.

3

– When turning into a bend, the radars may temporarily cease to detect vehicles in adjacent lanes.

– The function may warn you late when two other vehicles are approaching from the rear, side by side in the adja-

cent lanes (driving on a 3-lane road) and at a much higher speed than your vehicle.

– The system may not provide a warning when the other vehicles are travelling at a significantly different speed.

– If the vehicle is being overtaken by a long vehicle (e.g. heavy goods vehicle overtaking at a similar speed to the ve-

hicle) the system may interrupt the warning before the end of the manoeuvre.

– The vehicle is travelling on a winding road.

2 0 4 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

Safe distance alert

Activating/deactivating the

function

This function is an ad-

ditional driving aid. This

function is not under

any circumstances in-

tended to replace the due care

and attention of the driver, who

should at all times be in control

of the vehicle.

3

Location of camera 1

Make sure the windscreen is not ob-

scured (by dirt, mud, snow, conden-

sation etc.).

Location of the radar 2

From the "Vehicle" world on your

multimedia screen 3 , press the "Dri-

ving assistance" menu then press

the "Comfort" tab.

Activate or deactivate the "Follow-

ing distance" function.

Using the information from the

radar 2 and camera 1 , this function

informs the driver of the time inter-

val between their vehicle and the ve-

hicle in front so that a safe stopping

distance between the two vehicles

can be maintained.

Ensure that the radar area is not ob-

structed (by dirt, mud, snow, a badly

fitted front number plate etc.), im-

pacted, modified (including paint-

ing) or hidden by any accessory fit-

ted on the front of the vehicle (on the

grille or logo etc.).

The function is active from the ap-

proximately 19 mph (30 km/h).

Each time the vehicle is

started, the function con-

tinues the mode saved

the last time the engine was

stopped.

D r i v i n g - 2 0 5

ADDITIONAL DRIVING AID FUNCTIONS

(very insufficient distance between

Operation

the two vehicles).

The measurement is

displayed for informa-

tion: the system does

not carry out any ac-

If the interval between the two vehi-

cles is less than approximately 0.5

seconds, the indicator light 4 and

display D will flash in red on the in-

strument panel along with "-.- s".

Under certain conditions, the time

interval may not be displayed:

tion on the vehicle.

3

This function is not designed for

use in urban conditions or for a

dynamic driving style (sudden

cornering, acceleration, brak-

ing, etc.), but rather for stable

driving conditions.

– while cornering;

– when changing lane;

– if the vehicle in front is sufficiently

far or outside the range of the radar

or camera.

The function does not interact

with the braking system.

The radar and camera zones

must be kept clean and free of

any tampering in order to en-

sure the proper operation of the

system.

Any work carried out in the area

where the radar or camera is lo-

cated (repairs, replacements,

windscreen and/or bumper

modifications, etc.) must be car-

ried out by a qualified profes-

sional.

With the function activated, the 4 in-

dicator is displayed on the instru-

ment panel and informs the driver of

the distance between their vehicle

and the vehicle in front.

–

A (grey): function not operational;

A (green): no vehicle detected;

B (green): the time interval is

greater than or equal to around two

seconds (distance between the two

vehicles adapted to your speed);

–

C (orange): the time interval falls

between around 1 and 2 seconds (in-

sufficient distance between the two

vehicles);

–

D (red): the time interval is less

than or equal to around one second

2 0 6 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

Warnings

This function is an additional driving aid. This function is not under any circumstances intended to replace

the due care and attention of the driver, who should at all times be in control of the vehicle.

System servicing/repairs

3

– In the event of an impact, the radar and/or camera alignment may be changed and its operation may conse-

quently be affected. Deactivate the function and consult an authorised dealer.

– Any work carried out in the area where the radar and/or camera is located (replacements, repairs, windscreen

and/or bumper modifications, etc.) must be carried out by a qualified professional.

Only an authorised dealer is qualified to service the system.

In the event of system disturbance

– obstruction of the windscreen or the bumper (by dirt, ice, snow, condensation etc.);

– a complex environment (metal bridge, tunnel, etc.);

– poor weather conditions (snow, hail, black ice, etc.);

– poor visibility (night, fog, etc.);

– poor contrast between the vehicle preceding it and the surrounding area (e.g. white vehicle in a snowy area, etc.);

– being dazzled (glaring sun, lights of vehicles travelling in the opposite direction; etc.);

– the road is narrow, winding and undulating (tight bends etc.)

Risk of erroneous false alarms.

D r i v i n g - 2 0 7

ADDITIONAL DRIVING AID FUNCTIONS

– and stationary vehicles;

or

– surrounding pedestrians and cy-

clists.

This system can apply

maximum braking to the

vehicle until it is com-

Active emergency braking

pletely stationary if necessary.

For safety reasons, always wear

your seat belt when travelling in

your vehicle and make sure that

it is loaded so that no items can

be thrown forward and hit the

occupants.

The system informs the driver if

there is a risk of head-on collision to

enable appropriate emergency ma-

noeuvres (pressing the brake pedal

and/or turning the steering wheel).

Depending on the reactivity of the

driver, the system can assist with

braking in order to limit damage or

prevent a collision.

3

Location of the camera 1

The system is otherwise inactive

and does not trigger an alert.

Make sure the windscreen is not ob-

scured (by dirt, mud, snow, conden-

sation etc.).

This function is an ad-

ditional driving aid.

This function is not un-

Using information from the camera

1 and the radar 2 , the system deter-

mines the distance between your

vehicle:

– from the vehicle ahead in the

same lane;

Location of the radar 2

Make sure that the area around the

radar is not obscured (by dirt, mud,

snow or an incorrectly fitted number

plate), impacted, altered (including

paintwork) or hidden.

der any circumstances

intended to replace the due

care and attention of the driver,

who should at all times be in

control of the vehicle.

or

– from any oncoming vehicles in the

context of a manoeuvre to change

direction;

or

– and vehicles passing perpendicu-

larly;

or

2 0 8 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

"Brake" message appear on the in-

strument panel accompanied by a

beep.

Operation

Special features of warn-

ings

Note:

Depending on the speed,

the warning and braking may

be activated simultaneously.

– if the driver uses the vehicle con-

trols (steering wheel, pedals, etc.)

the system may delay its reaction or

not activate;

3

– if active emergency braking has

caused the vehicle to stop, the vehi-

cle is kept stationary for a short

time. Beyond this time limit, the dri-

ver must keep the vehicle stationary

by holding their foot on the brake

pedal;

– after the system activates brak-

ing, the "Advanced Safety trig-

gered" message will be displayed

Vehicle detection

Detection of vehicles travelling in

the same lane

A risk of a collision with the vehicle in

front of you in the same lane is de-

tectable by the system when the ve-

hicle is travelling at a speed over ap-

proximately 5 mph (8 km/h).

Detection of oncoming vehicles in

the context of a manoeuvre to

change direction

When driving, when there is a risk of

collision, the system:

– alerts you of a collision risk: the

"Detected obstacle" message ap-

pears on the instrument panel ac-

companied by a beep.

Note: if the driver presses the brake

pedal and the system still detects a

risk of collision, the braking force

may be increased if it is not suffi-

cient to prevent the collision.

In the event of an emer-

gency manoeuvre, you

can stop the braking at

any moment by:

– tapping the accelerator ped-

al;

or

– turning the steering wheel as

a collision avoidance manoeu-

vre.

– can trigger braking: if the driver

does not react to the alert and the

collision becomes imminent, the red

warning light or, depending on

the vehicle, the symbol 3 and the

D r i v i n g - 2 0 9

ADDITIONAL DRIVING AID FUNCTIONS

Stationary vehicles are detected by

Activation/deactivation

Depending on the vehicle,

the system when:

– your vehicle is travelling at a

speed between approximately 5

mph (8 km/h) and 50 mph (80 km/h).

according to the length of

time following the last

3

time the engine was stopped,

the function is reactivated:

Detection of pedestrians and cy-

clists

Detection of pedestrians and cy-

clists in the same lane

The system detects pedestrians and

cyclists when:

– your vehicle is travelling at a

speed between approximately 5

mph (8 km/h) and 53 mph (85 km/h).

– when the vehicle is unlocked;

or

– when a door is opened;

or

– when the engine is restarted.

When you wish to change direction

(e.g. A ), oncoming vehicles are de-

tected by the system when:

– your vehicle is travelling at a

speed between approximately 5

mph (8 km/h) to 12 mph (20 km/h);

– you have activated the direction

indicator light.

Detection of pedestrians and cy-

clists when changing direction

The system detects pedestrians and

cyclists when:

– your vehicle is travelling at a

speed between approximately 5

mph (8 km/h) and 12 mph (20 km/h).

Activating, deactivating the system

from the multimedia screen 4

Detection of vehicles crossing the

lane perpendicularly

Vehicles crossing the lane perpen-

dicularly are detected by the system

when:

– your vehicle is travelling at a

speed between approximately 12

mph (20 km/h) and 37 mph (60 km/h).

Detection of vehicles stopped in the

lane

2 1 0 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

the

warning light appears on

the instrument panel.

The possible causes are:

– the system is temporarily blinded

(glare from the sun, dipped beam

headlights, bad weather conditions

etc.). The system will be operational

again when visibility conditions are

better;

3

– the system is temporarily inter-

rupted (e.g. the windscreen, front or

rear bumper or logo is obscured by

dirt, mud, snow, condensation, etc.)

In this case, park the vehicle and

switch off the engine. Clean the

windscreen, the front bumper or the

logo. The next time the engine is

started, after around five or ten min-

utes of driving, the warning light and

the message disappear. If this is not

the case, this may arise from anoth-

er cause; contact an Approved Deal-

er.

To activate or deactivate the func-

tion, refer to the multimedia instruc-

tions.

With the vehicle stationary, to ac-

cess the function settings from the

multimedia screen 4 , refer to the

multimedia instructions:

Select "ON" or "OFF".

"Warning anticipation": adjust the

alert sensitivity level. To do this se-

lect:

– « Late » ;

– « Standard » ;

– « Early ».

Settings

For safety reasons, car-

ry out any adjustments

while the vehicle is sta-

tionary.

Operating faults

Please refer to the multimedia in-

structions for more information.

If the system detects a temporary

fault the

warning light illumi-

Temporarily not available

nates, or depending on the vehicle,

Settings from the multimedia screen

4

If the system detects a temporary

the warning light illuminates

on the instrument panel. Consult an

approved dealer.

fault, the

pears, or depending on the vehicle,

warning light ap-

D r i v i n g - 2 1 1

ADDITIONAL DRIVING AID FUNCTIONS

Warnings

This function is an additional driving aid. This function is not under any circumstances intended to replace

the due care and attention of the driver, who should at all times be in control of the vehicle. The triggering of

this function may be delayed or prevented when the system detects clear signs of control of the vehicle by

the driver (action on the steering wheel, pedals etc.).

3

The system cannot be activated:

– the gear control is in Neutral position;

– when the Electronic Stability Program (ESC) has started.

System servicing/repairs

– In the event of an impact, the radar and/or camera alignment may be changed and its operation may conse-

quently be affected. Deactivate the function and consult an authorised dealer.

– Any work in the area where the radar and/or camera is located (repairs, replacements, windscreen modifications,

etc.) must be carried out by a qualified professional.

Only an authorised dealer is qualified to service the system.

2 1 2 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

System disturbance

Some conditions can disturb or damage the system's operation, such as:

– a complex environment (metal bridge, tunnel, etc.);

– poor weather conditions (snow, hail, black ice, etc.);

– poor visibility (night, fog, etc.);

– poor contrast between the object (vehicle, pedestrian etc.) and the surrounding area (e.g. pedestrian dressed in

white located in a snowy area etc.);

3

– being dazzled (glaring sun, lights of vehicles travelling in the opposite direction; etc.);

– windscreen obscured (by dirt, ice, snow, condensation etc.);

– ...

In these conditions, the system may not react, may warn the driver or may brake inadvertently.

Limitation of the system operation

– Each time the vehicle is started, the system carries out a calibration according to the vehicle surroundings and

may be inactive for approximately two to five minutes;

– The radar and camera areas must be kept clean and free of any modifications to ensure the proper functioning of

the system if the conditions described in the "Special cases of oncoming vehicles when changing direction" are

met;

– the system may not respond to small vehicles such as motorbikes as effectively as to other vehicles;

– the system may not operate properly when the road surface is slippery (rain, snow, black ice, etc.);

– to ensure correct operation, the system needs to distinguish the complete outline of the pedestrian. So the system

cannot detect:

– pedestrians in the darkness or in poor lighting conditions;

– partially visible pedestrians;

– pedestrians less than approximately 80 cm;

– pedestrians carrying large objects;

– ...

In these conditions, the system may not react, may warn the driver or may brake inadvertently.

D r i v i n g - 2 1 3

ADDITIONAL DRIVING AID FUNCTIONS

Deactivating the function

You must deactivate the function if:

– the camera area has been damaged (e.g. on the inside or outside of the windscreen);

– the front of the vehicle was damaged (impact, scratch on the radar, etc.);

– the vehicle is being towed (breakdowns);

– the windscreen is cracked or distorted (do not carry out windscreen repairs in this area; have it changed by an ap-

proved dealer);

3

– you are not driving on a paved road.

In the event of the system behaving abnormally, deactivate it and consult an authorised dealer.

Halting the function

You can halt the active braking function at any time by tapping the accelerator pedal or by turning the steering

wheel in a collision avoidance manoeuvre.

2 1 4 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

– a few minutes have elapsed since

the vehicle last stopped;

– the vehicle speed is greater than

approximately 43 mph (70 km/h).

If there is a risk of fatigue or im-

paired attention, the "Vigilance alert

Have a break" 1 message is dis-

played on the instrument panel, ac-

companied by a beep.

Press switch 2 OK to delete the

warning.

After deleting the message, the sys-

tem continues vigilance monitoring

and issues a new warning if neces-

sary.

Operation

Driver vigilance warning

The driver vigilance warning is a

function that analyses the behav-

iour of the driver (driving style, vehi-

cle steering, etc.) and alerts them if

there is a risk of falling asleep.

It takes into account indicators such

as:

– steering wheel movements;

– driver actions on other systems

(indicators, brake pedal, etc.).

3

This function is an ad-

ditional driving aid in

case of risk of fatigue.

The function does not

The driver vigilance warn-

ing constantly monitors

the driver's attention and

can provide several warnings

per journey.

operate on the vehicle. The

function cannot, under any cir-

cumstances, replace the

driver's responsibility during dri-

ving.

The driver must always adapt

their driving according to their

alertness, regardless of the

system's indications.

The system resets every time

the engine is started.

The function is set to notify the dri-

ver if:

D r i v i n g - 2 1 5

ADDITIONAL DRIVING AID FUNCTIONS

Activation/deactivation

Activating and deactivating

alerts using the "My Safety" but-

ton 3

Depending on the vehicle,

alerts are automatically

deactivated when the

For safety reasons, car-

ry out any adjustments

while the vehicle is sta-

tionary.

"Lane Centring" function is acti-

vated. To re-activate the warn-

ings, the "Lane Centring" func-

tion must be deactivated. For

more information ꢀ 252.

3

Depending on the vehicle,

depending on the length

of time following the last

time the engine was stopped,

the alerts are reactivated:

Depending on the vehicle,

it may not be possible to

deactivate alerts.

– when the vehicle is unlocked;

or

– when a door is opened;

or

The alerts can be deactivated or ac-

tivated using "Custom" mode in the

"My Safety" function ꢀ 184.

If the alerts have previously been de-

activated using Custom mode:

– when the engine is started.

– to deactivate the alerts, press the

button 3 twice. The indicator light on

the button 3 goes out;

– To reactivate the alerts, press the

button 3 once. The indicator light on

the button 3 lights up.

When the alerts are deac-

tivated, the system con-

tinues to assess the

driver's state of fatigue.

2 1 6 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

– The clock is wrongly configured

road signs detected on the side of

the road.

It mainly uses information taken

from the camera 1 attached to the

windscreen behind the rear view

mirror.

Activating and deactivating the

alerts from the multimedia

screen 4

(depending on vehicle);

– winding roads;

– trailer traction.

Operating faults

3

If the system detects a fault, the

"Check Fatigue Warning System"

Depending on the country, the sys-

tem also uses information from a

map subscription to interpret cer-

tain signs (town entrance, etc.).

The sign displayed on the instru-

ment panel changes when a road

sign is detected by the system.

Once the speed limiter or the cruise

control is activated, you can adapt

the limited speed setpoint to the

speed limit displayed on the instru-

ment panel by the system (ꢀ 226 and

ꢀ 230).

message and the

warning

light are displayed on the instrument

panel.

Have the system checked by an au-

thorised dealer.

Detection of road signs

To activate or deactivate the alerts,

please refer to the multimedia in-

structions.

If the detected speed limit is exceed-

ed, the road sign displayed on the in-

strument panel is modified to inform

the driver.

Select "ON" or "OFF".

Limiting the operation of alerts

Location of the camera 1

Some conditions can disrupt or

damage the system operation, for

example:

– certain driving styles (incorrect

driving etc.);

Make sure the windscreen is not ob-

scured (by dirt, mud, snow, conden-

sation etc.).

Special features

– driving on a road in poor condition;

– strong side wind;

For vehicles with a map subscrip-

tion:

The system displays speed limits on

the instrument panel according to

D r i v i n g - 2 1 7

ADDITIONAL DRIVING AID FUNCTIONS

– if the vehicle is being driven in a

country where the speed units differ

from those of the vehicle, the system

displays the speed limit sign in the

unit of the country, alongside the

speed limit converted to the unit

used by the vehicle’s instrument

panel;

warn you. It remains illuminated on

the instrument panel as long as the

vehicle is exceeding the detected

speed limit.

Operation

Warning lights

Special features

3

– for countries where the speed limit

is reduced during rainy weather on

some types of roads, the system

may alter the detected speed limit

after a few seconds of the wind-

screen wipers being activated.

For vehicles without a map subscrip-

tion: when driving in a country where

speed units differ from those on your

vehicle, you can manually select the

speed unit shown on the instrument

panel (e.g. change the unit from

miles to kilometres) in order to dis-

play accurate information ꢀ 107.

Note: the system does not take into

account exceptional speed limit

measures, such as on peak pollution

days.

The function displays the following

warning lights:

2. Speed limit signs and additional

speed limit signs (speed on exit

ramp with arrow, speed with a cara-

van, speed limit with length of appli-

cation, etc.)

3. Additional road signs (start of no

overtaking zone).

If the detected speed limit is exceed-

ed, the circle around the road sign

flashes (warning light 2 ) accompa-

nied, depending on the vehicle, by a

beep emitted for a few seconds to

2 1 8 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

Activation/deactivation

Map subscription

Road sign detection is as-

sociated with a map sub-

scription.

Depending on the equipment, it

is necessary to update the

maps regularly.

For safety reasons, car-

ry out any adjustments

while the vehicle is sta-

tionary.

3

It the maps are not updated,

system performance will be im-

paired (incorrect speed limit,

etc.)

Depending on the vehicle, warnings

can be deactivated or activated

from the "Custom" mode of the "My

Safety" function ꢀ 184.

Note: if there is no map for a

country, a message will appear

on the multimedia screen to in-

form of this and suggest down-

loading the map information re-

lating to the country.

To manage the subscription,

please refer to the multimedia

instructions.

If there is no subscription, the

system will be limited to taking

into account the speed limit

signs when they are detected

by the camera.

The system will no longer take

into account information relat-

ed to the maps. The speed limit

availability may be affected.

Depending on the vehicle,

depending on the length

of time following the last

The sound alert can be deactivated

or activated using "Custom" mode

in the "My Safety" function ꢀ 184.

If the sound alert has previously

been deactivated using "Custom"

mode:

– to deactivate the sound alert,

press the button 4 twice. The indica-

tor light on the button 4 goes out;

– to reactivate the sound alert,

press the button 4 once. The indica-

tor light on the button 4 lights up.

Activating, deactivating the over-

speed sound alert from the multime-

dia screen 5

time the engine was stopped,

the sound alert is reactivated:

– when the vehicle is unlocked;

or

– when a door is opened;

or

– when the engine is restarted.

Activating, deactivating the over-

speed sound alert using the "My

Safety" button 4

D r i v i n g - 2 1 9

ADDITIONAL DRIVING AID FUNCTIONS

Variation of the limited speed or

cruising speed

Temporary unavailability

If the system is unavailable for rea-

sons related to the camera or map

data, the

symbol is displayed

on the instrument panel. If there is

still a problem, contact an approved

dealer.

3

The system cannot detect the speed

limit if:

– the windscreen is not clean;

– the camera is blinded by the sun;

– there is insufficient visibility (fog,

etc.);

– the signs are not legible (snow,

etc.) or are hidden (by another vehi-

cle or by trees);

– the information taken from the

map is not up to date.

Note: when the front camera is ob-

scured, the "Front camera no visibili-

ty" message is displayed on the in-

strument panel. Clean the wind-

screen area in front of the camera.

To activate or deactivate the sound

alert, please refer to the multimedia

instructions.

To adapt the speed limiter, cruise

control or adaptive cruise control

setpoint to the detected speed lim-

its: briefly press switch 6 to adjust

the vehicle's speed to the speed lim-

it indicated on the last detected

speed limit sign.

Select "ON" or "OFF".

Note: on vehicles with a map sub-

scription, you can automatically ad-

just the vehicle's speed to each new

limit indicated on the detected

speed limit signs. To do this, press

and hold switch 6 for approximately

two seconds.

Operating faults

When the system detects an operat-

ing fault, the

the instrument panel.

In some cases, they are accompa-

nied by the following message:

is displayed on

– « Driving assist unavailable » ;

2 2 0 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

or

– « Check Front camera » ;

or

– « Check Driving assist ». Consult an

approved Dealer.

3

D r i v i n g - 2 2 1

ADDITIONAL DRIVING AID FUNCTIONS

Warnings

This function is an additional driving aid. This function is not under any circumstances intended to replace

the due care and attention of the driver, who should at all times be in control of the vehicle.

The driver must always adapt their speed to the highway code and traffic conditions, regardless of system

indications.

3

The system may not detect all speed limit signs or may interpret them incorrectly.

The driver must not ignore road signs undetected by the system and should give priority to complying with the actu-

al road signs and the highway code.

In the event of poor visibility (fog, snow, frost, etc.), it is possible that the system may not indicate the correct speed

to the driver

2 2 2 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

When in reverse gear and moving at

between approximately 2 mph and 6

mph (3 km/h and 10 km/h), if there is

a risk of collision with a fixed obsta-

cle, the system automatically

Operation

Active emergency braking in

reverse gear

brakes the vehicle. A visual warning

3

2 is displayed on the multime-

dia screen 1 , accompanied by a

beep.

Once the vehicle has stopped, the

vehicle must be held stationary by

the driver keeping their foot on the

brake pedal.

This function is an ad-

ditional driving aid. This

function is not under

any circumstances in-

In addition to the "Park Assist" func-

tion ꢀ 275 and using information

from the four central sensors locat-

ed at the rear of the vehicle, the sys-

tem detects fixed obstacles located

behind your vehicle. If there is a sig-

nificant risk of collision, the system

automatically causes the vehicle to

brake.

tended to replace the due care

and attention of the driver, who

should at all times be in control

of the vehicle.

Note: make sure that the four cen-

tral sensors located at the rear of

the vehicle are not obscured (by dirt,

mud, snow, etc.).

Fixed rear obstacle detection

D r i v i n g - 2 2 3

ADDITIONAL DRIVING AID FUNCTIONS

To activate or deactivate the func-

Clean the ultrasonic sensors. If there

is still a problem, contact an ap-

proved dealer.

tion, select the "Vehicle" world, then

"Parking aids". Select "Active emer-

gency braking in reverse gear".

An impact to the un-

derside of the vehicle

while manoeuvring

If the vehicle is fitted with a towbar

recognised by the system and a

trailer has been connected, active

emergency braking in reverse gear

is automatically deactivated and

the "Trailer: parking sensors off"

message is displayed on the instru-

ment panel, accompanied by the

If the function is deactivated, the

(e.g. striking a post,

raised kerb or other street furni-

ture) may result in damage to

the vehicle (e.g. deformation of

an axle).

To avoid any risk of accident,

have your vehicle checked by

an approved dealer.

warning light 3

is displayed on

3

the multimedia screen.

Operating faults

When the system detects an operat-

ing fault, active emergency braking

in reverse gear is automatically de-

activated.

warning light 3

on the multi-

media screen.

Activating or deactivating the

system

The warning light 3

is dis-

played on the multimedia screen ac-

companied by, depending on the

type of malfunction, the following

message on the instrument panel:

– "Parking sensors unavailable";

or

– "Check parking sensors";

or

– "Driving aids unavailable";

or

– "Check driving aids".

Depending on the vehicle, the mes-

sage is accompanied by the display

of the

warning light on the

instrument panel.

2 2 4 - D r i v i n g

ADDITIONAL DRIVING AID FUNCTIONS

Warnings

Active emergency braking in reverse gear

This function is an additional driving aid. This function cannot, under any circumstances, replace the vigi-

lance and responsibility of the driver.

3

Some climatic and environmental conditions can disrupt or damage the system. As a consequence, the dri-

ver should always be ready for sudden incidents while driving: always ensure that there are no small, narrow moving

obstacles (such as a child, animal, pushchair, bicycle, stone, post, etc.) in the blind spot when manoeuvring.

The triggering of this function may be delayed or prevented when the system detects clear signs of control of the

vehicle by the driver (action on the steering wheel, pedals etc.).

System servicing/repairs

– In the event of an impact, the rear sensors and their performances may be affected. Deactivate the function and

consult an authorised dealer.

– Any work in the area where the sensors are located (repairs, replacements, bumper modifications etc.) must be

carried out by a qualified professional.

Only an authorised dealer is qualified to service the system.

Deactivating the function

You must deactivate the function if the vehicle is being towed (breakdown recovery) or if the vehicle is fitted with a

towbar that is not recognised by the system.

In the event of the system behaving abnormally, deactivate it and consult an authorised dealer.

D r i v i n g - 2 2 5

Driving -> Additional driving aid functions for Your Renault Symbioz 4 Door First Generation (2024-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals