Get Getting to know your vehicle -> Child seats Guide for Renault Symbioz 4 Door First Generation (2024-2026)

CHILD SAFETY

which is to prevent the child seat

from moving in the event of a colli-

sion.

The ISOFIX anchoring

points have been ex-

In the latter three cases check that

your child seat can be installed by

consulting the list of compatible ve-

hicles.

clusively designed for

child seats equipped

2

with the ISOFIX system. Never

fit a different type of child seat,

seat belt or other objects to

these fittings.

Check that nothing is obstruct-

ing the anchorage points.

If your vehicle has been in-

volved in a road accident, have

the ISOFIX anchorage points

checked and replace your child

seat.

No modifications must

be made to the origi-

nally-fitted restraint

system components:

seat belts, ISOFIX and seats and

their mountings.

The two rings are located behind the

zip fasteners 1 between the seat

back and seat base and are identi-

Attach the child seat using the

ISOFIX locks, if equipped. The ISOFIX

system allows quick, easy and safe

fitting.

The ISOFIX system consists of 2 rings

and, in some cases, a third ring.

fied by a

mark.

Before using an ISOFIX

child seat that you pur-

chased for another ve-

The third ring 4 is used to attach the

upper strap on some child seats. 2

on some child seats.

hicle, check that its in-

Rear seats

stallation is authorised. Consult

the list of vehicles which can be

fitted with the seat with the

equipment manufacturer.

7 2 - G e t t i n g t o k n o w y o u r v e h i c l e

CHILD SAFETY

The ISOFIX anchoring

points have been ex-

clusively designed for

child seats equipped

2

with the ISOFIX system. Never

fit a different type of child seat,

seat belt or other objects to

these fittings.

Check that nothing is obstruct-

ing the anchorage points.

If your vehicle has been in-

volved in a road accident, have

the ISOFIX anchorage points

checked and replace your child

seat.

The upper strap 2 should be posi-

tioned between the seatback and

the rear parcel shelf. To do so, re-

move the rear parcel shelf ꢀ 319.

Attach the hook 3 of the upper strap

2 to the ring 4 identified by the

symbol.

All seats

Attach the hook 3 to one of the rings

Check that the seat-

back of the forward-

facing child seat is in

Pull the upper strap 2 so that the

back of the child seat comes into

contact with the back of the vehicle

seat.

4 marked by the

symbol.

Front passenger seat

contact with the seat-

back of the vehicle seat. In this

case, the child seat may not al-

ways rest on the seat base of

the vehicle seat.

G e t t i n g t o k n o w y o u r v e h i c l e - 7 3

CHILD SEATS

different child seat, check with the

manufacturer that it can be fitted.

Do not change other settings after

installing the child seat.

Fitting a child seat, general in-

formation

Some seats are not suitable for fit-

ting child seats. The diagram indi-

cates where to fit a child seat.

In the front seat

2

RISK OF DEATH OR SE-

RIOUS INJURY: before

fitting a rear facing

The laws concerning children travel-

ling in the front passenger seat dif-

fer in every country. Consult the rele-

vant legislation and follow the indi-

cations on the diagram.

Before fitting a child seat in this seat

(if authorised):

child seat on the front

passenger seat, check that the

airbag has been deactivated

ꢀ 92.

Fit the child seat in a

rear seat wherever

possible.

Make sure the child

– lower the seat belt as far as possi-

ble;

– move the seat as far back as pos-

sible;

– gently tilt the seatback away from

the vertical position (approximately

25°);

– on equipped vehicles, raise the

seat base as far as possible.

seat or the child's feet do not

prevent the front seat from

locking correctly ꢀ 49 ꢀ 52.

Check that when installing the

child seat in the vehicle it is not

at risk of coming loose from its

base.

In the rear side seat

A carrycot can be installed across

the vehicle and will take up at least

two seats. Position the child with his

or her feet nearest the door.

In order to install a rear-facing child

seat, move the front seat as far for-

ward as possible, then move the

front seat back as far as it will go,

without allowing it to come into con-

tact with the child seat.

For the safety of the child in the for-

ward-facing position:

– move the seat in which the child

will be seated as far back as possi-

ble;

If you have to remove the head-

rest, check that it is correctly

stored so that it does not come

loose under harsh braking or im-

pact.

Always attach the child seat to

the vehicle even if it is not in use

so that it does not come loose

under harsh braking or impact.

Always fully raise the seat headrest

so that it does not interfere with the

child seat ꢀ 49.

After installing the child seat, when

this is possible, you can move the ve-

hicle seat forward if necessary (so

as to leave enough space in the rear

seats for passengers or other child

seats). For a rear-facing child seat,

do not let it touch the dashboard or

move it to the furthest forward posi-

tion.

– Move the seat in front of the child

forwards, and set the position of the

seatback to avoid contact between

the seat and the child's legs.

The types of child seats indicated

may not be available. Before using a

7 4 - G e t t i n g t o k n o w y o u r v e h i c l e

CHILD SEATS

Ensure that the child

seat or the child's feet

do not prevent the

Installing a booster

seat (group 2 or 3)

Check that the seat

belt ꢀ 55 operates

Fit the child seat in a

rear seat wherever

possible.

2

locking in place of the

To install an ISOFIX

seat in front ꢀ 52 or ꢀ 49.

(winds) correctly.

child seat on this seat, unbuckle

the seat belts by hand before

engaging the bolts.

Adjust the seat belt by position-

ing:

In all situations, remove the head-

rest of the rear seat on which the

child seat is positioned ꢀ 52. If nec-

essary, position the rear seat as far

back as possible. This must be done

before fitting the child seat. Check

that the child seat is resting against

the back of the rear seat.

– the shoulder strap on the

child's shoulder without it

touching their neck;

– the lap belt so that it lies flat

on the thighs and against the

pelvis.

Fitting an ISOFIX child

seat on the rear left-

hand seat will mean

that the central seat

If necessary, adjust the position

of the vehicle seat.

cannot be used. The central

seat belt will no longer be either

accessible or useable.

A child seat with floor

supports must never be

installed on the rear

centre seat.

RISK OF DEATH OR SERIOUS IN-

JURY.

G e t t i n g t o k n o w y o u r v e h i c l e - 7 5

CHILD SEATS

Attachment by seat belt

Fitting diagram

2

7 6 - G e t t i n g t o k n o w y o u r v e h i c l e

CHILD SEATS

Check the status of the airbag before fitting a child seat or allowing a passenger to use the seat.

Seat not suitable for fitting child seats.

2

Child seat attached using the belt

Seat equipped for attaching a "universal" approved seat using a seatbelt.

Seat enabling a child seat with "B2" approval to be attached by seat belt.

RISK OF DEATH OR SERIOUS INJURY: before fitting a rear facing child seat on the front passenger seat,

check that the airbag has been deactivated ꢀ 92.

Using a child safety system which is not approved for this vehicle will not properly protect the baby or child.

They risk serious or even fatal injury.

Check that your child is always strapped in and that the belt or safety harness used is correctly set and ad-

justed ꢀ 55.

If necessary, adjust the seat position accordingly.

G e t t i n g t o k n o w y o u r v e h i c l e - 7 7

CHILD SEATS

Installation table

The table below summarises the information shown on the installation diagram in order to ensure the regulations in

force are respected.

2

Front passenger seat

Weight of the

child

Rear centre

seat

Type of child seat

Rear side seats

With airbag de- With airbag ac-

activated

tivated

Carrycot fitted across the

vehicle

Group 0

< 10 kg (22 lbs)

X

U (2)

U (3)

X

< 10 kg (22 lbs)

and < 13 kg (28.7

lbs)

Rear-facing shell seat

Groups 0 or 0 +

U (1) (5)

X

< to 13 kg (28.7

lbs) and 9 (19.7

lbs) to 18 kg (39.7

lbs)

Shell seat/rear-facing seat

Groups 0+ and 1

U (1) (5)

X

U (3)

U (4)

X

Forward-facing seat

Group 1

9 to 18 kg (19.7 to

39.7 lbs)

X

U (5)

15 to 25 kg and

22 to 36 kg (33.1

to 55.1 lbs and

48.5 to 79.4 lbs)

Booster seat

Groups 2 and 3

U (5) / B2 (6)

U / B2 (4)

X

7 8 - G e t t i n g t o k n o w y o u r v e h i c l e

CHILD SEATS

(1) RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child seat in this seat, make sure that the

front passenger airbag has been deactivatedꢀ 92.

2

X = Seat not suitable for fitting child seats of this type.

U = Seat enabling a child seat with "Universal" approval to be attached by seat belt: check that it can be fitted.

B2 = Boosters in groups 2 and 3 (15 to 25 kg and 22 to 36 kg/33.1 to 55.1 lbs and 48.5 to 79.4 lbs).

(2) A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet

nearest the door.

(3) If necessary, position the vehicle seat as far back as possible. In order to install a rear-facing child seat, move the front

seat as far forward as possible, then move the front seat back as far as it will go, without allowing it to come into contact

with the child seat.

(4) Always retract the headrest of the rear seat on which the child seat is positioned. This action must be performed be-

fore fitting the child seat ꢀ 52. Move the seat in front of the child forwards, move the seatback forward to avoid contact

between the seat and the child's legs.

(5) Raise the seat to the maximum and position it as far back as possible, tilting the seatback slightly (approximately 25°).

(6) Raise the seat to the maximum and position it as far back as possible, tilting the seatback slightly (approximately 25°).

The child seat must not be in contact with the centre console or the dashboard.

G e t t i n g t o k n o w y o u r v e h i c l e - 7 9

CHILD SEATS

Attachment using the ISOFIX system

Fitting diagram

2

Version with front passenger seat equipped with ISOFIX

8 0 - G e t t i n g t o k n o w y o u r v e h i c l e

CHILD SEATS

For the front passenger seat, the use of a child seat with a floor support is recommended to avoid triggering

the seat belt warning signal.

2

Using a child safety system which is not approved for this vehicle will not properly protect the baby or child.

They risk serious or even fatal injury.

Seat which does not allow a child seat to be fitted.

Child seat attached using theISOFIX system

Seat equipped for attaching a ISOFIX or i-Size child seat.

The front and rear seats are equipped with an anchorage point allowing an ISOFIX universal forward-facing child

seat to be attached. The anchoring points are located on the passenger seatback for the front seat and on the bench

seatback for the rear seats.

RISK OF DEATH OR SERIOUS INJURY:

before fitting a rear facing child seat on the front passenger seat, check that the airbag has been deacti-

vated ꢀ 92.

Fit the child seat in a rear seat wherever possible.

To install an ISOFIX seat in this seat, unbuckle the seat belt by hand before engaging the bolts.

G e t t i n g t o k n o w y o u r v e h i c l e - 8 1

CHILD SEATS

Fitting a seat ISOFIX in the rear-left seat means the middle seat cannot be used. The central seat belt will no

longer be either accessible or useable.

2

8 2 - G e t t i n g t o k n o w y o u r v e h i c l e

2

G e t t i n g t o k n o w y o u r v e h i c l e - 8 3

CHILD SEATS

Installation table

Version with front passenger seat equipped with ISOFIX

The table below summarises the information shown on the installation diagram in order to ensure the regulations in

force are respected.

2

Front passenger seat

Without

airbag or

with airbag

deactivated

Weight of the Size of seat

Rear side

seats

Rear centre

seat

Type of child seat

With airbag

activated

child

[fixture]

Carrycot fitted across

the vehicle

Group 0

L1 [F]

L2 [G]

< 10 kg (22 lbs)

< 13 kg

X

Rear-facing shell seat

Groups 0 or 0 +

R1 [E]

IL (1) (5)

IL (2)

< to 13 kg (28.7

lbs) and 9 (19.7

lbs) to 18 kg

(39.7 lbs)

Rear-facing seat

Groups 0+ and 1

R3 [C]

R2 [D]

IL (1) (5)

X

IL (2)

X

F3 [A]

F2 [B]

F2X [B1]

Forward-facing seat

Group 1

IUF - IL

(1)

IUF - IL

(2)(3)

9 to 18 kg (19.7

to 39.7 lbs)

15 to 25 kg

and 22 to 36

kg (33.1 to 55.1

lbs and 48.5

to 79.4 lbs)

IUF - IL

(4)

IUF - IL

(2) (3)

B2

B3

X

Booster seat

Groups 2 and 3

X

8 4 - G e t t i n g t o k n o w y o u r v e h i c l e

CHILD SEATS

Front passenger seat

Without

Weight of the Size of seat

child [fixture]

Rear side

seats

Rear centre

seat

Type of child seat

airbag or

with airbag

deactivated

With airbag

2

activated

Rear-facing seat

i - U (1) (5)

X

i - U (2)

X

Seati-Size

Forward-facing seat

Booster seat

X

i - UF (1)

i - UF (4)

i - UF (2) (3)

X = Seat not suitable for fitting child seats.

IUF = Seat allowing a child seat with "Universal or vehicle-specific" approval to be attached using the ISOFIX system on

equipped vehicles; check that it can be fitted.

IL = Seat allowing a child seat with "Semi-universal or vehicle-specific" approval to be attached using the ISOFIX system

on equipped vehicles; check that it can be fitted.

i-U = Suitable for "Universal" front-facing and rear-facing i-Size restraint devices.

i-UF = Suitable only for "universal" front-facing and rear-facing i-Size restraint devices.

(1) Move the vehicle seat backwards as far as possible and lower it as much as possible, then tilt the seatback slightly (by

approximately 25°).

(2) If necessary, position the vehicle seat as far back as possible. In order to install a rear-facing child seat, move the front

seat as far forward as possible, then move the front seat back as far as it will go, without allowing it to come into contact

with the child seat.

(3) Always retract the headrest of the rear seat on which the child seat is positioned. This action must be performed be-

fore fitting the child seat ꢀ 52. Move the seat in front of the child forwards, move the seatback forward to avoid contact

between the seat and the child's legs.

(4) Raise the seat to the maximum and position it as far back as possible, tilting the seatback slightly (approximately

25°). The child seat must not be in contact with the centre console or the dashboard.

The size of the ISOFIX child seat is indicated by a letter:

–

F3,F2,F2X [A, B, B1]: for forward-facing seats in group 1 (9 to 18 kg);

B2, B3: boosters in groups 2 and 3 (15 to 25 kg and 22 to 36 kg);

G e t t i n g t o k n o w y o u r v e h i c l e - 8 5

CHILD SEATS

–

R3, R2 [C, D]: rear-facing seats or shell seats in group 0+ (less than 13 kg) or group 1 (9 to 18 kg);

R1 [E]: rear-facing shell seats in group 0 (less than 10 kg) or 0+ (less than 13 kg);

L1,L2 [F, G]: carrycots in group 0 (under 10 kg).

2

(5) RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child seat to the front passenger seat,

check that the airbag has been deactivated ꢀ 92.

8 6 - G e t t i n g t o k n o w y o u r v e h i c l e

2

G e t t i n g t o k n o w y o u r v e h i c l e - 8 7

CHILD SEATS

Fitting diagram

Version with front passenger seat not equipped with the ISOFIX

2

8 8 - G e t t i n g t o k n o w y o u r v e h i c l e

CHILD SEATS

For the front passenger seat, the use of a child seat with a floor support is recommended to avoid triggering

the seat belt warning signal.

2

Using a child safety system which is not approved for this vehicle will not properly protect the baby or child.

They risk serious or even fatal injury.

Seat which does not allow a child seat to be fitted.

Child seat attached using theISOFIX system

Seat equipped for attaching a ISOFIX or i-Size child seat.

The front and rear seats are equipped with an anchorage point allowing an ISOFIX universal forward-facing child

seat to be attached. The anchoring points are located on the passenger seatback for the front seat and on the bench

seatback for the rear seats.

Fit the child seat in a rear seat wherever possible.

To install an ISOFIX seat in this seat, unbuckle the seat belt by hand before engaging the bolts.

Fitting a seat ISOFIX in the rear-left seat means the middle seat cannot be used. The central seat belt will no

longer be either accessible or useable.

G e t t i n g t o k n o w y o u r v e h i c l e - 8 9

CHILD SEATS

Installation table

Version with front passenger seat not equipped with the ISOFIX

The table below summarises the information shown on the installation diagram in order to ensure the regulations in

force are respected.

2

Weight of the

child

Size of seat [fix- Front passen-

Rear centre

seat

Type of child seat

Rear side seats

ture]

ger seat

Carrycot fitted across the

vehicle

Group 0

L1 [F]

L2 [G]

< 10 kg

< 13 kg

X

Rear-facing shell seat

Groups 0 or 0 +

R1 [E]

X

IL (1)

X

Rear-facing seat

Groups 0+ and 1

R3 [C]

R2 [D]

< to 13 kg and 9

to 18 kg

F3 [A]

F2 [B]

F2X [B1]

Forward-facing seat

Group 1

IUF - IL

(1)(2)

9 to 18 kg

X

IUF - IL

(1) (2)

B2

Booster seat

Groups 2 and 3

15 to 25 kg and

22 to 36 kg

B3

X

Rear-facing seat

i - U (1)

Seati-Size

Forward-facing seat

Booster seat

i - UF (1) (2)

X = Seat not suitable for fitting child seats.

9 0 - G e t t i n g t o k n o w y o u r v e h i c l e

CHILD SEATS

IUF = Seat allowing a child seat with "Universal or vehicle-specific" approval to be attached using the ISOFIX system on

equipped vehicles; check that it can be fitted.

IL = Seat allowing a child seat with "Semi-universal or vehicle-specific" approval to be attached using the ISOFIX system

on equipped vehicles; check that it can be fitted.

i-U = Suitable for "Universal" front-facing and rear-facing i-Size restraint devices.

i-UF = Suitable only for "universal" front-facing and rear-facing i-Size restraint devices.

2

(1) If necessary, position the vehicle seat as far back as possible. In order to install a rear-facing child seat, move the front

seat as far forward as possible, then move the front seat back as far as it will go, without allowing it to come into contact

with the child seat.

(2) Always retract the headrest of the rear seat on which the child seat is positioned. This action must be performed be-

fore fitting the child seat ꢀ 52. Move the seat in front of the child forwards, move the seatback forward to avoid contact

between the seat and the child's legs.

The size of the ISOFIX child seat is indicated by a letter:

–

F3,F2,F2X [A, B, B1]: for forward-facing seats in group 1 (9 to 18 kg);

B2, B3: boosters in groups 2 and 3 (15 to 25 kg and 22 to 36 kg);

R3, R2 [C, D]: rear-facing seats or shell seats in group 0+ (less than 13 kg) or group 1 (9 to 18 kg);

R1 [E]: rear-facing shell seats in group 0 (less than 10 kg) or 0+ (less than 13 kg);

L1,L2 [F, G]: carrycots in group 0 (under 10 kg).

G e t t i n g t o k n o w y o u r v e h i c l e - 9 1

Getting to know your vehicle -> Child seats for Your Renault Symbioz 4 Door First Generation (2024-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals