Get Operation -> Opening and closing Guide for Cupra Formentor SUV First Generation (2020-2024)

Operation

2

3

Lock the vehicle

held down for a longer period it will flash sev-

eral times, such as for convenience opening.

Opening and closing

Unlock only the rear lid. Press the button

until all the turn signals on the vehicle

flash briefly. You have 2 minutes to open

the rear lid. Once this time has passed, it

will lock again. In addition, the lamp on

the key flashes.

If the vehicle key control lamp does not light

up when the button is pressed, replace the

Set of vehicle keys

key's battery page 94 .

›››

Vehicle key

Key socket

4

5

Control lamp

There is a key socket near the start button

Alarm button. Only press in the event of

an emergency! When the alarm button is

pressed, the vehicle's sounds and the

turn signals light up for a short time.

Press again to disconnect.

Fig. 71 . Warning! Do not confuse with the

location for the emergency start

›››

page 210.

›››

Spare key

To obtain a spare key and other vehicle keys,

the vehicle ID number is required.

With the vehicle key the vehicle may be

locked or unlocked remotely page 95 .

›››

Each new key contains a microchip which

must be coded with the data from the vehi-

cle electronic immobiliser. A vehicle key will

not work if it does not contain a microchip or

the microchip has not been encoded. This is

also true for keys which are specially cut for

the vehicle.

The vehicle key includes an emitter and bat-

tery. The receiver is in the interior of the ve-

hicle. The range of the vehicle key with re-

mote control and new battery is several me-

tres around the vehicle.

Fig. 70 Vehicle key

If it is not possible to open or close the vehi-

cle using the remote control key, this should

The vehicle keys or new spare keys can be

obtained from a specialised CUPRA dealer or

SEAT Official Service, a specialised workshop

or an approved key service qualified to cre-

ate this kind of key.

be re-synchronised page 94 or the bat-

›››

tery changed page 94 .

›››

Different keys belonging to the vehicle may

be used.

Fig. 71 Centre console: vehicle key socket.

New keys or spare keys must be synchronised

Control lamp on the vehicle key

before use page 94 .

›››

Key to Fig. 70

›››

When a button on the vehicle key is briefly

pressed, the indicator lamp flashes

4

1

Unlock the vehicle

Fig. 70 once briefly, but if the button is

›››

92

Opening and closing

Pull out the key blade

WARNING

also possible even when you are outside the

radius of action.

●

Never leave children or disabled persons

●

Key operation can be greatly influenced

in the vehicle. In case of emergency, they

may not be able to leave the vehicle or

manage on their own.

by overlapping radio signals close to the ve-

hicle working in the same range of frequen-

cies, for example, radio transmitters or mo-

bile telephones.

●

An uncontrolled use of the key could

start the engine or activate any electric

equipment (e.g. electric windows), causing

risk of accident. The doors can be locked

using the remote control key. This could

become an obstacle for assistance in an

emergency situation.

●

Obstacles between the remote control

and the vehicle, bad weather conditions

and discharged batteries can considerably

reduce the range of the remote control.

●

If the buttons of the vehicle key are

Fig. 72 Vehicle key: remove the key blade.

pressed or one of the central locking but-

●

Never forget the keys inside the vehicle.

tons page 97 is pressed repeatedly in

›››

An unauthorised use of your vehicle could

result in injury, damage or theft. Therefore

always take the key with you when you leave

the vehicle.

The central locking remote control has the

key blade inside it for use in case of emer-

gency locking/unlocking of the driver's door

short succession, the central locking briefly

disconnects as protection against over-

loading. The vehicle is then unlocked. Lock

it if necessary.

page 104.

›››

●

Never remove the key from the ignition if

●

Spare remote control keys are available at

the vehicle is in motion. Otherwise, the

steering could suddenly block and it would

be impossible to steer the vehicle.

●

1

If you press button Fig. 72

once the

›››

your Technical Service, where they must be

matched to the locking system.

key blade is unlocked and a ring appears as a

key ring.

●

Up to five remote control keys can be

●

1

Press and hold the button

and at the

used.

CAUTION

same time pull on the ring in the direction of

All of the vehicle keys contain electronic

components. Protect them from damage,

impacts and humidity.

2

arrow Fig. 72

key blade.

to completely remove the

›››

Note

●

Only use the key button when you require

the corresponding function. Pushing the

button unnecessarily could accidentally

unlock the vehicle or trigger the alarm. It is

93

Operation

Changing the battery

To change the battery

●

When fitting the battery, check that the

polarity is correct.

●

Remove the key blade from the vehicle key

page 93.

›››

●

For the sake of the environment

Insert the key blade into the slot Fig. 73 ,

press it in the direction of arrow

›››

1

and de-

Please dispose of your used batteries cor-

rectly and with respect for the environ-

ment.

2

tach the cover by levering it

.

●

Extract the battery from the compartment

using a suitable thin object Fig. 74 .

›››

●

Insert the new battery and press it into the

battery compartment

.

Synchronize the vehicle key

›››

●

Place the cover and press it into the vehi-

If the  button is pressed frequently outside

of the vehicle range, it is possible that the ve-

hicle can no longer be locked or unlocked

using the key. In this case, the key must be

resynchronised as described below:

Fig. 73 Vehicle key: opening the battery

compartment cover.

cle key housing until it clicks into place.

WARNING

Swallowing a battery with a 20 mm diame-

ter or any other button battery can cause

serious and even fatal injuries within a very

short time.

●

Remove the key blade from the vehicle key

page 92.

›››

●

Keep the vehicle key and key fobs with

Press the  button on the vehicle key. For

this, it must remain with the vehicle.

batteries out of reach of children.

●

If you suspect that someone may have

●

Open the vehicle within one minute using

swallowed a battery, seek immediate medi-

cal attention.

the key blade. The key has been synchron-

ised.

Fig. 74 Vehicle key: removing the battery.

●

If necessary, fit the cap.

CAUTION

CUPRA recommends you ask a specialised

workshop to replace the battery.

●

If the battery is not changed correctly,

the vehicle key may be damaged.

The battery is located to the rear of the vehi-

cle key, under a cover.

●

Use of unsuitable batteries may damage

the vehicle key. For this reason, always re-

place the dead battery with another of the

same voltage, size and specifications.

94

Opening and closing

Self-locking system to prevent involuntary

unlocking

●

Never leave individuals locked in a closed

Central locking

and locked vehicle. In case of emergency,

they may not be able to exit the vehicle by

themselves or get help.

It is an anti-theft system and prevents the

unintentional unlocking of the vehicle. If the

vehicle is unlocked and none of the doors

(including the boot) are opened within 30

seconds, it re-locks automatically.

Introduction

Central locking functions correctly when all

the doors and the rear lid are correctly shut.

If the driver door is open, the vehicle cannot

be locked with the key.

Description

Unlocking one side of the vehicle only

Central locking allows all doors, the rear lid

and the tank flap to be unlocked centrally:

WARNING

When you lock the vehicle with the key, the

doors and the rear lid are locked. When you

open the door, you can either unlock only

the driver door, or all the vehicle doors. To

select the required option, use the Infotain-

The incorrect use of the central locking

system may cause serious injuries.

●

From outside, using the vehicle key

page 96.

›››

●

The central locking system will lock all

From outside with the Keyless Access

doors. A vehicle locked from the inside can

prevent any non-authorised individual

from opening the doors and accessing the

vehicle. Nevertheless, in case of emergency

or accident, locked doors will complicate

access to the vehicle interior to help the

passengers.

page 98 system,

›››

●

ment system setting page 96 .

›››

From inside, by pushing the central locking

button page 97 .

›››

Automatic locking (Auto Lock)

The Auto Lock function locks the doors and

the rear lid when the vehicle exceeds a

speed of about 15 km/h (9 mph).

Various functions are available to improve

the vehicle safety:

●

Never leave children or disabled people

●

Security system “Safe” page 101

›››

The vehicle can be unlocked via the central

locking switch or by pulling one of the door

handles.

alone in the vehicle. The central locking

button can be used to lock all the doors

from within. Therefore, passengers will be

locked inside the vehicle. Individuals locked

in the vehicle can be exposed to very high

or very low temperatures.

Self-locking system to prevent involuntary

unlocking

●

Selective unlocking system

In the event of an accident in which the air-

bags inflate, the doors will be automatically

unlocked to facilitate access and assistance.

Automatic speed dependent locking and

unlocking system (Auto Lock)

●

Depending on the time of the year, tem-

●

Emergency unlocking system

peratures inside a locked and closed vehi-

cle can be extremely high or extremely low

resulting in serious injuries and illness or

even death, particularly for young children.

Turn signals

The turn signals will flash twice when the ve-

hicle is unlocked and once when the vehicle

is locked.

»

95

Operation

If it does not flash, this indicates that one of

the doors, the rear lid or the bonnet is not

closed correctly.

Central locking settings

Unlock and lock from the outside

Central locking settings can be changed in

the Infotainment system.

Accidental lock-out

Unlocking doors

The central locking system prevents you

from being locked out of the vehicle in the

following situations:

●

Press the function button  > Vehicle >

Exterior > Central locking > Door unlock-

ing.

●

If the driver door is open, the vehicle can-

not be locked with the central locking switch

You can choose to unlock all the doors or

only the driver door when you unlock the

vehicle. In all the options, the fuel tank flap is

also unlocked.

page 97.

›››

Fig. 75 Remote control key: buttons.

Lock the vehicle with the remote control key,

when all the doors and the rear lid have been

closed. This prevents the accidental locking

of the vehicle.

●

Lock: press the  Fig. 75 button.

›››

With the Driver setting, when you press the

 button on the remote control key once,

only the driver door is unlocked. If that but-

ton is pressed twice, the rest of the doors

and the rear lid will be unlocked.

Locking the vehicle without the “Safe” se-

curity system: push the  button again and

hold for 2 seconds.

Note

●

Unlock: press the  button.

●

Never leave any valuable items in the ve-

hicle unattended. Even a locked vehicle is

not a safe.

If the  button is pressed, all the vehicle

doors are locked. At the same time, a confir-

mation signal is heard.

Unlocking the rear lid: hold down the 

button for at least 1 second.

●

If the LED on the driver door sill lights up

The vehicle will be locked again automatical-

ly if you do not open one of the doors or the

rear lid within 30 seconds after unlocking the

car. This function prevents the vehicle from

remaining unlocked if the unlocking button is

pressed by mistake. This does not apply if

you press the  button for at least one sec-

ond.

for about 30 seconds when the vehicle is

locked, the central locking system or anti-

theft alarm is not working properly. You

should have the fault repaired at a special-

ised CUPRA dealer, SEAT Official Service or

specialised workshop.

●

Vehicle interior monitoring by the anti-

theft alarm system will only function as in-

tended if the windows and sunroof are

closed.

96

Opening and closing

●

Selective unlocking system

You can open the doors individually from

the inside by pulling the inside door handle.

●

Other functions of the remote control

key page 111, Convenience open/close

›››

The selective unlocking system allows you to

only unlock the driver door and the fuel tank

flap. All other doors and the rear lid remain

locked.

function.

●

In the event of an accident in which the

airbags inflate, doors locked from the inside

will be automatically unlocked to facilitate

access and assistance.

Unlocking and locking from the

inside

Unlocking the driver's door and tank flap:

●

WARNING

Press (once) the  button on the remote

control key or turn the key once in the open-

●

The central locking switch also works

ing direction.

with the ignition switched off, except when

the “safe” system is activated.

Unlocking all the doors, the rear lid and the

tank flap simultaneously:

●

The central locking switch does not oper-

ate if the vehicle is locked from the outside

and the security system is switched on.

●

Within 5 seconds, press (twice) the  but-

ton on the remote control key, or turn the

key twice within 5 seconds in the opening di-

rection.

●

Locked doors could delay assistance in an

emergency. Do not leave anyone, especial-

ly children, in the vehicle.

The Safe security system and the anti-theft

alarm deactivate immediately when only the

driver door is opened.

Fig. 76 In the centre console: central lock-

ing switch

Note

Your vehicle will lock automatically when it

reaches a speed of about 15 km/h (9 mph)

In vehicles with Infotainment system, you can

programme the security central locking sys-

●

Lock: press the  Fig. 76 button.

›››

(Auto Lock) page 95 . You can unlock the

›››

Unlock: Press the  button again

Fig. 76.

vehicle again using the  button on the

tem directly page 96 .

›››

central locking switch.

WARNING

Please note the following when using the

central locking switch to lock your vehicle:

Observe the safety warnings

in Lock-

›››

ing system “Safe” on page 101.

●

It is not possible to open the doors or the

rear lid from the outside (for safety reasons,

e.g. when stopped at traffic lights).

Note

●

Do not use the remote control key until

●

The LED in the central locking switch lights

up when all the doors are closed and locked.

the vehicle is visible.

97

Operation

Depending on the equipment, the vehicle

may have the Keyless Access system.

If the vehicle is not unlocked for an extended

period, the function is deactivated.

Unlock and lock the vehicle with

Keyless Access

The vehicle can be unlocked and locked via

the front doors only. When doing so, the re-

mote control key must be no further than

approx. 1.5 m away from the door handle.

Configure the Keyless Access system

The behaviour of the Keyless Access system

can be adjusted in the Vehicle settings

menu of the Infotainment system.

It does not matter where you carry the key,

e.g. in your jacket pocket.

If the Keyless Access function is disabled, its

operation is limited.

Once the doors have been locked, they can-

not be opened again immediately. This will

enable you to check that the doors are prop-

erly closed.

Keyless Access is a key-free locking and igni-

tion system to unlock and lock the vehicle

without actively using its key. For this, it is on-

ly necessary that there is a valid vehicle key in

the detection area corresponding to the at-

tempted access to the vehicle.

Fig. 77 Keyless Access: proximity zones.

If you wish you may unlock only the corre-

sponding door or the entire vehicle. The

necessary adjustments can be performed in

vehicles with a driver information system

Unlock the vehicle

page 89.

›››

●

Touch the surface of the sensor located in-

A

side the handle . All turn signals will flash

General information

twice.

If a valid key is in the proximity of the car

Fig. 77, the Keyless Access locking and

›››

If the sensor surface is touched twice, the

entire vehicle will unlock.

starting system gives the key entry as soon as

one of the sensor surfaces on the front door

handles is touched.

Automatic vehicle unlock

Fig. 78 Door handle: sensor surfaces

The following features are then available

without having to use the vehicle key active-

ly:

The vehicle can be unlocked automatically.

To do this, the function must be activated in

the Infotainment system and the vehicle key

must be in the proximity zone of the vehicle.

Fig. 78

›››

A

Unlocking sensor surface on the inside

of the door handle.

●

Keyless Entry: unlocking the vehicle using

B

Locking sensor surface on the outside

of the door handle.

If the key is in the proximity zone, the vehicle

is automatically unlocked.

the handles of the front doors or the soft-

touch/handle on the rear lid.

98

Opening and closing

●

A

Keyless Exit: locking the vehicle using the

Fig. 78

(arrow) of the handle and the

Unlocking and locking the boot hatch

›››

sensor of the driver or passenger door han-

dle.

vehicle unlocks.

When the vehicle is locked, the rear lid auto-

matically unlocks on opening if there is a val-

id vehicle key in the proximity zone

●

Open the door.

●

Easy Open: opening the rear lid moving

On vehicles with selective opening or info-

tainment system configuration, pulling the

door handle twice will unlock all doors.

one foot below the rear bumper

›››

●

Fig. 77.

›››

page 109.

Open or close the rear lid normally.

Press & Drive: keyless starting of the engine

After closing, the hatch locks automatically.

If the complete vehicle is unlocked, the rear

lid will not lock automatically after closing it.

with the starter button page 207 .

›››

In vehicles without the “Safe” security sys-

tem: closing and locking the doors

(Keyless-Exit)

The central locking and locking systems op-

erate in the same way as a normal locking

and unlocking system. Only the controls

change.

●

What happens when locking the vehicle

with a second key

Switch the ignition off.

Close the driver's door.

If there is a vehicle key inside the vehicle and

it is locked from the outside with a second

vehicle key, the key inside the vehicle is

Unlocking the vehicle is confirmed with a

double flash of the indicator lights; locking

by a single flash.

●

Touch (once) the locking sensor surface

B

Fig. 78

(arrow) on one of the front door

›››

handles. The door that is used must be

closed.

blocked for engine ignition page 207 . In

›››

If the vehicle is locked and then all doors and

the rear lid are closed leaving the last key

used inside the vehicle and none outside,

the vehicle will not lock immediately. All the

vehicle's indicator lights will flash four times.

The vehicle will lock after a few seconds if

you do not open any door or the rear lid.

order to enable engine ignition, press the 

button on the key inside the vehicle.

In vehicles with the “Safe” security system:

closing and locking the doors (Keyless-

Exit)

Automatically disabling sensors

If the vehicle is not locked or unlocked for a

long period of time, the proximity sensors on

the passenger doors are automatically disa-

bled.

●

Switch the ignition off.

Close the driver's door.

The vehicle will lock again after a few sec-

onds if you unlock the vehicle but fail to

open any door or boot hatch.

Touch (once) the sensor surface Fig. 78

›››

B

(arrow) on one of the front door handles.

If one of the sensor surfaces on the door

handles is often activated in an unusual man-

ner with the vehicle locked (e.g. by the

branches of a bush rubbing against it), all

proximity sensors are disabled for a certain

period of time.

The vehicle locks with the “Safe” security

system page 101 . The door that is used

must be closed.

›››

Unlocking and opening the doors

(Keyless-Entry)

●

Touch (twice) the sensor surface Fig. 78

›››

●

Grip one of the front door handles. When

you do this, you touch the sensor surface

B

(arrow) of one of the front door handles

to lock the vehicle without activating the

“Safelock” security system page 101 .

»

Sensors will again be enabled:

›››

99

Operation

●

After a time.

The next time the door is locked/unlocked,

Keyless Access will be active again.

Note

OR: if the vehicle is unlocked with the but-

●

If the vehicle battery has little or no

ton  on the key.

charge, or the vehicle key battery is almost

or entirely out of charge, you will probably

not be able to lock or unlock the vehicle

with the Keyless Access system. The vehicle

can be unlocked or locked manually

Keyless Access permanent disconnection

function

●

OR: if the boot is opened.

OR: if the vehicle is unlocked manually with

You can deactivate the vehicle unlock with

Keyless Access permanently in the infotain-

ment system so that others cannot unlock or

start the vehicle.

the key.

page 104.

›››

●

Keyless Access temporary disconnection

function

To control the proper locking of the vehi-

cle, the release function is disabled for ap-

prox. 2 seconds.

You can deactivate the vehicle's Keyless

Access unlocking for one locking and un-

locking cycle.

Convenience functions

●

If the message Keyless access system

To close all the electric windows and the

sunroof using the comfort function, keep a

finger for a few seconds on the locking sen-

B

faulty is displayed on the screen of the

dash panel, abnormalities may occur in the

operation of the Keyless Access system.

Contact a specialised workshop. To do so,

CUPRA recommends going to a specialised

CUPRA dealer or any SEAT dealership.

●

Move the gear lever to position P since

otherwise the vehicle cannot be locked.

sor surface Fig. 78

handle until the windows and roof have

closed.

(arrow) of the door

›››

●

Close the door.

Push the central locking button  on the

How the doors open when touching the

sensor surface on the door handle will de-

pend on the settings that have been activa-

ted in the infotainment system, using the

function button  > Vehicle > Exterior >

Central locking.

●

Depending on the function set on the in-

remote control and touch the locking sensor

surface of the driver door handle

fotainment system for the mirrors, the ex-

terior mirrors will unfold and the surround

lighting will come on when unlocking the

vehicle using the sensor surface on the

driver and passenger door handles

B

Fig. 78

within the following 5 seconds.

›››

Do not grasp the door handle; otherwise the

vehicle will not unlock. Deactivation is also

possible if the vehicle is locked through the

driver’s door lock.

page 125.

›››

●

CAUTION

If there is no valid key inside the vehicle

●

To check that the function has been deac-

or the system fails to detect one, a warning

will display on the dash panel screen. This

could happen if any other radio frequency

signal interferes with the key signal (e.g.

from a mobile device accessory) or if the

key is covered by another object (e.g. an

aluminium case).

The sensor surfaces on the door handles

could engage if hit with a water jet or high

pressure steam if there is a valid vehicle key

in the proximity. If at least one of the elec-

tric windows is open and the sensor surface

tivated, wait at least 10 seconds, grip and pull

on the door handle. The door should not

open.

The next time the door can only be unlocked

via the remote control or the lock cylinder.

B

Fig. 78

(arrow) on one of the handles

›››

is activated continuously, all windows will

close.

100

Opening and closing

Lock the vehicle and activate the “Safe”

security system.

●

If the sensors are very dirty, e.g. have a

WARNING

layer of salt, the correct functioning of the

sensors on the door handles may be affec-

ted. In this case, clean the vehicle.

Do not leave anyone (especially children) in

the vehicle if it is locked from the outside

and the “Safe” security system is activated,

as the doors and windows cannot then be

opened from the inside. Locked doors

could delay assistance in an emergency.

●

Press the locking button  once on the ve-

hicle key.

●

If the vehicle is fitted with an automatic

gearbox, the vehicle can only be locked by

pressing the parking lock button P.

Lock the vehicle without activating the

“Safe” system.

●

To improve the safety of your vehicle, the

●

Press the locking  button on the vehicle

key twice.

remote control of the system is equipped

with a position sensor. If this remote con-

trol does not detect movement for a cer-

tain length of time, the system will con-

clude that the vehicle cannot be opened

(e.g. on a night table) so it will be disabled.

●

OR: touch the sensor surface on the out-

Anti-theft alarm system

B.

side of the door handle twice Fig. 78

›››

Description

When the “Safe” security system is disa-

bled, the following needs to be taken into

account:

●

If, when trying to block the vehicle, the

The anti-theft alarm makes it more difficult

to break into the vehicle or steal it. The sys-

tem will initiate acoustic and optical warning

signals when your vehicle is tried to be

forced.

last used key is still inside, all the turn sig-

nals will flash 4 times.

●

The vehicle can be unlocked and opened

from the inside using an door handle.

●

The anti-theft alarm is activated.

Locking system “Safe”¹⁾

The anti-theft alarm is automatically turned

on when the vehicle is locked with the key.

The system is immediately activated and the

turn signal light located on the driver door

will flash along with the turn signals, indicat-

ing that the alarm and the locking security

system (double lock) have been turned on.

The vehicle interior monitoring system and

the anti-tow system are disabled.

When the vehicle is blocked, the “Safe” se-

curity system puts the door handles out of

operation and prevents unauthorised per-

sons for entering. The doors cannot be

“Safe” status

The flashing frequency of the diode in the

door sill immediately confirms the process.

Initially, the diode flashes in a fast sequence

for a brief period, then it stops for approxi-

mately 30 seconds and, lastly continues

flashing slowly.

opened from inside

.

›››

Depending on the vehicle, when switching

the ignition off, a warning may be displayed

on the control panel screen stating that the

“Safe” security system is activated.

If any of the doors or the bonnet are open,

they will not be included in the protection

zones of the vehicle when the alarm is con-

nected. If the door or the bonnet are

»

1)

Available depending on market and version.

101

Operation

●

subsequently closed, they will be automati-

cally included in the protection areas of the

vehicle and the turn signals will flash accord-

ingly when the doors close.

Movement inside the vehicle (in vehicles

Note

with interior monitoring page 103 ).

›››

●

After 28 days, the indicator light will be

●

When the vehicle is towed (in vehicles with

anti-tow system page 103 ).

switched off to prevent the battery from

exhausting if the vehicle has been left

parked for a long period of time. The alarm

system remains activated.

›››

●

When the vehicle is raised (in vehicles with

anti-tow system page 103 ).

●

The turn signal light will flash twice on

opening and deactivating the alarm.

›››

●

If, after the audible warning goes off, an-

●

When the vehicle is transported on a ferry

●

The turn signal light will flash once on clos-

other monitored area is accessed (e.g. the

rear lid is opened after a door has been

opened), the alarm is triggered again.

or by rail (vehicles with an anti-tow system or

vehicle interior monitoring page 103 ).

ing and activating the alarm.

›››

When does the system trigger an alarm?

●

When a trailer connected to the anti-theft

●

The anti-theft alarm is not activated

alarm system is disconnected.

The anti-theft alarm siren will be triggered

for about 30 seconds alongside a sound and

optical (flashing) warning signals and will be

repeated about ten times when the vehicle is

locked and the following unauthorised ac-

tions are attempted:

when the vehicle is locked from within us-

ing the central locking button .

How to turn OFF the alarm

●

If the driver door is unlocked mechani-

●

Unlock the vehicle with the unlock button

 of the key.

cally with the key, only the driver door is

unlocked, the rest of the doors remain

locked. Only when the ignition has been

turned on will the other doors be available -

but not unlocked - and the central locking

button will be activated.

●

OR: turn the ignition on with a valid key.

●

Opening a door that is mechanically un-

If the driver’s door is unlocked mechanically

using the key, the ignition must be turned on

within 15 seconds of opening the door.

locked using the vehicle key without switch-

ing on the ignition in the next 15 seconds (in

certain markets, such as the Netherlands,

there is no 15 second waiting time and the

alarm is activated immediately on opening

the door).

●

If the vehicle battery is run down or flat

then the anti-theft alarm will not operate

correctly.

Otherwise, the alarm will trigger for 30 sec.

and the ignition will be blocked.

●

Vehicle monitoring remains active even if

the battery is disconnected or not working

for any reason.

CAUTION

●

A door is opened.

If the anti-theft security system is switched

off, the vehicle interior monitoring and the

tow-away protection are automatically dis-

connected.

Opening the bonnet.

●

The alarm is triggered immediately if one

of the battery cables is disconnected while

the alarm system is active.

The rear lid is opened.

When the ignition is switched on with a

non-authorised key.

●

Undue manipulation of the alarm.

Disconnection of the vehicle battery.

102

Opening and closing

The vehicle interior monitoring and the anti-

tow system are automatically switched on

again next time the vehicle is locked.

The following cases may cause a false

alarm:

Interior monitoring and the anti-

tow system

●

Open windows (partially or fully).

It is a monitoring or control function incor-

porated in the anti-theft alarm which detects

unauthorised vehicle entry by means of ul-

trasound.

If you wish to switch off the vehicle interior

monitoring and the anti-tow system, it must

be done each time that the vehicle is locked;

if not, they will be automatically switched on.

Panoramic/tilting sunroof open (partially

or completely).

●

Movement of objects inside the vehicle,

such as loose papers, items hanging from

the rear vision mirror (air fresheners), etc.

The vehicle interior monitoring and anti-tow

sensor (tilt sensor) are automatically switch-

ed on when the anti-theft alarm is switched

on. In order to activate it, all the doors and

the rear lid must be closed.

The vehicle interior monitoring and the anti-

tow system should be switched off if animals

are left inside the locked vehicle (otherwise,

their movements will trigger the alarm) or

when, for example, the vehicle is transported

or has to be towed with only one axle on the

ground.

Note

●

If the vehicle is relocked and the alarm is

activated without the volumetric sensor

function, relocking will activate the alarm

with all its functions, except the volumetric

sensor. This function is reactivated when

the alarm is switched on again, unless it is

deliberately switched off.

If the “Safe” page 101 security system is

›››

switched off, the vehicle interior monitoring

and the tow-away protection are automati-

cally disconnected.

Deactivation through the infotainment

system

●

If the alarm has been triggered by the

Activation

●

Turn off the ignition and press the function

volumetric sensor, this will be indicated by

a flashing of the warning lamp on the driver

door when the vehicle is opened. The flash

is different to the flash indicating the alarm

is activated.

button  > Vehicle > Exterior > Central

locking > Interior monitoring.

●

It is automatically switched on when the

anti-theft alarm is activated.

●

When the vehicle is locked now, the vehi-

cle interior monitoring and the tow-away

protection are switched off until the next

time the door is opened.

Deactivation

●

Open the vehicle with the key, either me-

●

The vibration of a mobile phone left in-

chanically or by pressing the  button on the

remote control. The time period from when

the door is opened until the ignition is

turned on should not exceed 15 seconds,

otherwise the alarm will be triggered.

side the vehicle may cause the vehicle inte-

rior monitoring alarm to trigger, as both

sensors react to movements and shakes in-

side the vehicle.

False alarms

Interior monitoring will only operate correct-

ly if the vehicle is completely closed. Please

observe related legal requirements.

●

If on activating the alarm, any door or the

rear lid is open, only the alarm will be acti-

vated. The vehicle interior monitoring and

the anti-tow system will only be activated

●

Press the  button on the remote control

twice. The volumetric sensor and tilt sensors

will be deactivated. The alarm system re-

mains activated.

»

103

Operation

door opens. Please observe the instructions

relating to the anti-theft alarm system

●

once all the doors are closed (including the

rear lid).

Open and close the doors and the rear lid

only when there is nobody in the way.

page 101.

›››

CAUTION

●

Remove the key blade from the vehicle key

page 92.

›››

●

When opening and closing in an emergen-

cy, carefully disassemble components and

then reassemble them carefully to avoid

damage to the vehicle.

Doors

Insert the key blade into the lock cylinder

to unlock or lock the vehicle.

Introduction

Special characteristics

The doors and rear lid can be locked man-

ually and partially opened, for example if the

key or the central locking is damaged.

●

The anti-theft alarm will remain active

Emergency unlocking or locking

of the driver’s door

when vehicles are unlocked. However, the

alarm will not be triggered page 101 .

›››

WARNING

●

After the driver door is opened, you have

Opening and closing doors carelessly can

cause serious injury.

15 seconds to switch on the ignition. Once

this time has elapsed, the alarm is triggered.

●

If the vehicle is locked from outside, the

●

Switch the ignition on. The electronic im-

doors and windows cannot be opened from

the inside.

mobilizer recognises a valid vehicle key and

deactivates the anti-theft alarm system.

●

Never leave children or disabled people

alone in the car. They could be trapped in

the car in an emergency and will not be

able to get themselves to safety.

Note

The anti-theft alarm is not activated when

the vehicle is locked manually using the key

●

Depending on the time of the year, tem-

shaft page 95 .

›››

Fig. 79 Driver door handle: locking cylin-

der.

peratures inside a locked and closed vehi-

cle can be extremely high or extremely low

resulting in serious injuries and illness or

even death, particularly for young children.

If the central locking system should fail to

operate, the driver door can still be locked

and unlocked by turning the key in the lock.

WARNING

As a general rule, when the driver door is

locked manually all other doors are locked.

When it is unlocked manually, only the driver

Getting in the way of the doors and the rear

lid is dangerous and can lead to serious in-

jury.

104

Opening and closing

Childproof locks

anti-clockwise for the right hand side

doors.

Emergency lock of doors without

lock cylinders

Deactivating the childproof lock

–

Unlock the vehicle and open the door

whose childproof lock you want to deacti-

vate.

–

With the door open, rotate the groove in

the door using the ignition key, anti-clock-

wise for the left hand side doors Fig. 81

›››

and clockwise for the right hand side

doors.

Fig. 81 Childproof lock on the left hand

side door.

Once the childproof lock is activated, the

door can only be opened from the outside.

Fig. 80 Locking the door manually.

The childproof lock prevents the rear doors

from being opened from the inside. This sys-

tem prevents minors from opening a door

accidentally while the vehicle is running.

If the central locking system should fail to

work at any time, doors with no lock cylinder

will have to be locked separately.

Rear lid

The emergency lock is located on the front

of the front passenger's door and the rear

doors. It can only be seen if the door is open.

This function is independent of the vehicle

electronic opening and locking systems. It

only affects rear doors. It can only be activa-

ted and deactivated manually, as described

below:

Introduction

The rear lid unlocks and locks together with

the doors.

●

Pull the cap out of the opening.

Insert the key in the inside slot and turn it

On vehicles with Keyless Access, the rear lid

unlocks automatically when it is opened

to the right as far as it will go (if the door is on

the right side) or to the left (if the door is on

the left side).

Activating the childproof lock

page 98.

–

›››

Unlock the vehicle and open the door in

which you wish to activate the childproof

lock.

●

Replace the cap.

WARNING

Once the door has been closed it can no

longer be opened from the outside. Pull the

interior door handle once to unlock and

open the door.

Careless and unsuitable locking, opening

and closing of the rear lid can cause acci-

dents and serious injury.

–

With the door open, rotate the groove in

the door using the ignition key, clockwise

»

for the left hand side doors Fig. 81 and

›››

105

Operation

Opening and closing

●

The rear lid must not be opened when

Note

the reverse or rear fog lights are lit. This

may damage the tail lights.

●

To open: place slight pressure on the han-

dle. The rear lid opens automatically.

Before closing the rear lid, make sure that

the key has not been left inside the luggage

compartment.

●

Do not close the rear lid by pushing it

●

To close: hold one of the handles on the

down with your hand on the rear window.

The glass could smash. Risk of injury!

inner trim and close it by moving it down-

wards, or press the button on the rear lid

›››

●

Ensure the rear lid is locked after closing

Fig. 83.

Opening and closing the rear lid

it. If not, it may open unexpectedly while

driving.

If the doors are locked, the rear lid is also

locked.

●

Closing the rear lid without observing and

ensuring it is clear could cause serious in-

jury to you and to third parties. Make sure

that no one is in the path of the rear lid.

●

Never drive with the rear lid open or half-

closed, exhaust gases may penetrate into

the interior of the vehicle. Danger of poi-

soning!

●

Never leave the vehicle unattended or al-

low children to play inside or next to it, es-

pecially if the rear lid is open. Children

could enter the luggage compartment,

close the rear lid and become trapped. A

locked vehicle can reach extremely high

and low temperatures, depending on the

time of year, thus causing serious injuries,

illness or even death.

Fig. 82 Rear lid: opening from outside.

The rear lid opening system operates electri-

cally. It is activated by exerting slight pressure

on the handle Fig. 82 .

›››

To lock or unlock the rear lid, press the  or

 buttons of the vehicle key.

A warning appears on the instrument panel

display if the rear lid is open or not properly

closed. An audible warning is also given if it is

opened while the vehicle is moving faster

than 6 km/h (4 mph).

CAUTION

Before opening or closing the rear lid, make

sure that there is enough space to open or

close it, e.g. when pulling a trailer or in a ga-

rage.

106

Opening and closing

●

locked if an authorised key is recognised in

the proximity of the vehicle.

OR: manually move the rear lid in the di-

Rear lid with electric opening and

closing

rection of closing until it closes automatical-

ly.

●

OR: depending on the features, pull the 

●

button on the driver door upwards

The rear lid goes down automatically to the

Fig. 84. The button also works when the

ignition is switched off.

final position and also closes automatically

›››

in Introduction on page 105.

›››

●

OR: press and hold the  button of the

Interrupting opening or closing

vehicle key for approx. 1 second. If the vehi-

cle is locked, only the rear lid is unlocked (the

doors remain locked).

After beginning to open or close the rear lid,

the action can be halted by pressing one of

the  buttons.

●

OR: on vehicles with Keyless Access and

sensor-controlled opening you can open the

rear lid by moving one foot in the area of the

sensors located below the rear bumper (Easy

If you press one of the  buttons again, the

rear lid will move again in the original direc-

tion.

Fig. 83 Rear lid: button to close the rear lid.

Open page 109 ). The rear lid will be auto-

›››

If the rear lid is met with resistance or an ob-

stacle during the automatic opening or clos-

ing, opening or closing will be interrupted

immediately. For the closing process, the

rear lid opens again slightly.

matically opened.

Closing the rear lid

●

Briefly press the  button on the rear lid

Fig. 83

in Introduction on page 105.

›››

●

›››

●

Check why it has not been possible to

open or close the rear lid.

OR: depending on the features, pull the 

button on the driver door upwards

Fig. 84.

●

Try to open or close the rear lid again.

›››

●

OR: on vehicles with Keyless Access, press

If necessary, the rear lid can be opened or

Fig. 84 On the driver’s door: button to

open and close the rear lid.

and hold the  vehicle key button until the

rear lid is closed, or move one foot into the

area of the sensors located below the rear

closed by hand using reasonable force.

Particular features if towing a trailer

Opening the rear lid

bumper (Easy Open) page 109 . The vehi-

›››

If the factory-fitted towing bracket is electri-

cle key must be in the Keyless Access system

detection zone at the rear outside the vehi-

cle.

●

Unlock the vehicle page 95 and briefly

›››

cally connected to a trailer page 291 , the

›››

press the handle of the rear lid. On vehicles

with Keyless Access you can directly press

the handle of the rear lid. The rear lid is un-

electric rear lid can only be opened or closed

with the buttons on the rear lid itself or by

using the Easy Open function.

»

107

Operation

●

Acoustic warnings

Release the rear lid and open it to the

or, after opening, it may lower by itself due

to the extra weight and cause serious in-

jury.

memorised height.

Throughout the process of opening or clos-

ing the rear lid, acoustic warnings can be

heard. Exception: when the rear lid is

●

Lift the rear lid by hand as far as it goes. To

do this, some force will have to be used.

●

Do not open the rear lid when there is a

opened manually using the handle or the

Easy Open function with the movement of

the foot or closed using the button on the

lot of snow on it or when carrying a load

(e.g. on a rack).

●

Press the  button Fig. 83 on the rear

›››

lid for at least 3 seconds.

●

Before opening the rear lid, remove the

●

This resets and memorises the factory-set

rear lid itself Fig. 83 .

›››

snow or the load.

opening angle. Memorisation is indicated by

blinking of the hazard warning lights and an

audible warning.

Modifying and memorising the opening

angle

If the space behind or above the vehicle is

less than the travel area of the rear lid, you

can change the opening angle of the rear lid.

Automatic protection against overheating

If the system is operated repeatedly in a

short space of time, it automatically switches

off to prevent overheating.

To memorise a new opening angle, the rear

lid must be open at least halfway.

Once the system is cool again, the function

can be reused. Until then, the rear lid can

only be opened and closed by hand using

reasonable force.

●

Interrupt the opening process in the de-

sired position.

●

Press the  button Fig. 83 on the rear

›››

lid for at least 3 seconds.

If with the rear lid open the vehicle battery is

disconnected page 333 or the corre-

›››

The opening angle is memorised. Memorisa-

tion is indicated by blinking of the hazard

warning lights and an audible warning.

sponding fuse burns out page 58 , the sys-

›››

tem will have to be reset. This requires clos-

ing the rear lid completely once.

Resetting and memorising the opening

angle

Emergency unlocking

page 110

›››

For the rear lid to reopen completely, the

opening angle must be reset and memorised

again.

WARNING

If a lot of snow builds up on the rear lid or it

is heavily loaded, the rear lid may not open

108

Opening and closing

●

Switch the ignition off.

Stand in front of the rear bumper, in the

If the rear bumper is very dirty.

Rear lid with sensor-controlled

opening and closing (Easy Open)

If the rear bumper is wet with salt water,

middle.

e.g. after having driven on gritted roads.

●

With a brisk movement, bring your foot

If the vehicle has been equipped at a later

and lower leg as close as you can to the

bumper. The lower part of the leg needs to

be close to the upper sensor area and your

foot must be close to the lower sensor area

1

time with a tow bracket.

In the event of heavy rain, the Easy Open

feature may take a little longer to open the

boot or may deactivate automatically, to

avoid the boot opening by accident, e.g. be-

cause of the running water.

Fig. 85

.

›››

●

Quickly remove your foot and lower leg

2

from the sensor areas Fig. 85

lid will be automatically opened.

. The rear

›››

The Easy Open function can be connected

and disconnected permanently in the info-

tainment system using the button  > Vehi-

cle > Exterior > Central locking.

●

If the rear lid fails to open, repeat the pro-

Fig. 85 Rear lid with sensor-controlled

opening (Easy Open).

cedure after a few seconds. The detection

zone of the lower sensor may not have been

reached Fig. 86 .

›››

WARNING

The rear lid can be closed with another foot

movement similar to the opening one (provi-

ded a valid vehicle key is in the proximity of

the rear lid).

If there is a valid key in the proximity of the

rear lid, in some cases the Easy Open func-

tion may be accidentally activated and the

rear lid will open, for example, when

sweeping under the rear bumper, when di-

recting a water jet or high pressure steam to

the area or when carrying out maintenance

work or repairs in that area. If accidentally

opened, the rear lid could injure somebody

situated in its area of operation or cause

material damage.

When closed, the rear lid automatically locks

if the vehicle has been locked beforehand

and there is no valid key inside.

While the rear lid is in motion (either open-

ing or closing), it can be stopped with anoth-

er foot movement similar to the opening one

(provided a valid vehicle key is in the proximi-

ty of the rear lid).

Fig. 86 Lower sensor detection area.

If there is a valid vehicle key in the proximity

of the rear lid, it is possible to unlock and

open or close it moving one foot in the area

of the sensors located under the rear bump-

er.

●

Therefore, always make sure that there is

no unsupervised valid key in the area near

the rear lid.

The Easy Open feature is not available or on-

ly has limited availability in the following sit-

uations (examples):

●

Before carrying out any maintenance or

»

repair work on the vehicle, always disable

109

Operation

●

Unlocking the rear lid from inside the lug-

gage compartment

Closing the window: pull the button .

the Easy Open feature via the infotainment

system.

Buttons on the driver door

●

Using the key blade, break the pre-

●

Before washing the vehicle, always disa-

punched sheet push it out towards the inside

of the luggage compartment.

1

ble the Easy Open feature via the infotain-

ment system.

Window on the front left door

2

Window on the front right door

●

Before attaching a bicycle rack or a trail-

Insert the key blade into the slot and move

3

Window on the rear left door

er, page 291 , always disable the Easy

›››

the key in the direction of the arrow until the

4

Window on the rear right door

Open feature via the infotainment system.

lock unlocks Fig. 87 .

›››

5

Safety switch for deactivating the electric

window buttons in the rear doors.

Emergency unlocking of the rear

lid

The front and rear electric windows can be

operated by using the controls on the driver

door. The other doors each have a switch for

their own window.

Window controls

Electrically opening and closing

the windows

Always close the windows fully if you park the

vehicle or leave it unattended

.

›››

You can use the electric windows for approx.

10 minutes after switching off the ignition if

neither the driver door nor the front passen-

ger door have been opened.

Safety switch 

Fig. 87 Detail of the luggage compart-

ment: emergency unlocking

5

The safety control Fig. 88

on the driver

›››

door can be used to disable the electric win-

dow buttons on the rear doors.

The rear lid can be unlocked from inside in

the event of an emergency (e.g. no battery).

Safety switch not pressed: buttons on rear

doors are activated.

Fig. 88 Detail of the driver's door: window

controls.

There is a groove in the luggage compart-

ment allowing access to the emergency

opening mechanism.

Safety switch pressed: buttons on rear doors

are deactivated.

●

Opening the window: press the button .

110

Opening and closing

●

The safety control symbol  lights up in yel-

low if the buttons on the rear doors are

switched off.

During convenience closing, first the win-

dows and then the sliding sunroof will be

closed.

Release the button and pull upwards and

hold again. The one-touch function is now

ready for operation.

In the infotainment system different settings

can be adjusted using the function button 

> Vehicle > Exterior > Windows > Conven-

ience opening.

The automatic one-touch electric windows

can be reinitialised individually or several at a

time.

Convenience open/close function

The electric windows can be opened or

closed from outside using the vehicle key:

WARNING

Convenience opening:

One-touch opening and closing

Observe the safety warnings

duction on page 104.

in Intro-

›››

●

Press and hold the  button on the remote

The one-touch automatic opening and clos-

ing is used to open or close the windows

completely. It will not be necessary to hold

the button of the corresponding electric

window.

control key until all the windows and the sun-

roof have reached the desired position.

●

Incorrect use of the electric windows can

result in injury.

●

OR: First unlock the vehicle using the 

●

Never close the rear lid without observing

button on the remote control key and then

keep the key in the driver door lock until all

the windows and the sunroof have reached

the required position.

and ensuring it is clear, to do otherwise

could cause serious injury to you and third

parties. Make sure that no one is in the path

of a window.

For the automatic raising function: pull the

button for the corresponding window up-

wards until it reaches the second position.

●

If the ignition is switched on, the electric

Convenience closing:

For the automatic lowering function: push

the button for the corresponding window

upwards until it reaches the second position.

equipment could be activated with risk of

injury, for example, in the electric windows.

●

Press and hold button  on the remote

control key until all the windows and the sun-

roof are closed

●

The doors can be locked using the re-

.

›››

Stop automatic movement: push or pull on

the button of the corresponding window.

mote control key. This could become an

obstacle for assistance in an emergency sit-

uation.

●

OR: Keep the key in the driver door in the

"lock" position until all the windows and the

sunroof are closed.

Resetting one-touch opening and closing

●

Therefore always take the key with you

●

OR using the Keyless Access system (only

when you leave the vehicle.

The one-touch opening and closing function

is not active after the vehicle battery has

been disconnected or is flat and will have to

be reset.

locking): Press and hold the locking sensor

●

The electric windows will work until the

surface Fig. 90 (arrow) on the door han-

›››

ignition has been switched off and one of

the front doors has been opened.

dle for several seconds to close the windows

and the sunroof. If you release the sensor

surface, the closing movement stops.

●

If necessary, use the safety switch to disa-

●

Pull the button of the corresponding win-

ble the rear electric windows. Make sure

that they have been disabled.

dow and hold it for one second in this posi-

tion.

»

111

Operation

●

If there is no obvious reason why the win-

●

For safety reasons, you should only use

WARNING

dow cannot be closed, try to close it again by

pulling the tab within ten seconds. The win-

dow closes with maximum force. The roll-

back function is now deactivated.

the remote control open and close func-

tions within about 2 metres of the vehicle.

To avoid injuries, always keep an eye on the

windows when pressing the button to close

them. The windows stop moving as soon as

the button is released.

If the sunroof is used negligently or without

paying due attention, it can cause serious

injury.

●

Open or close the sunroof and the sun

●

If more than 10 seconds pass, the window

blind only when no one is in their path of

movement.

will open fully when you operate one of the

buttons. One-touch closing is reactivated.

●

Never leave any key inside the vehicle

Note

when exiting.

WARNING

If the window is not able to close because it

is stiff or because of an obstruction, the

window will automatically open again

●

Never leave a child or any other person

Observe the safety warnings

in Elec-

›››

who may need help in the vehicle, especial-

ly if they have access to the vehicle key. If

using they key unattended, they could lock

the vehicle, start the engine, switch on the

ignition and activate the sunroof.

trically opening and closing the windows on

page 111.

page 112. If this happens, check why the

›››

window could not be closed before at-

tempting to close it again.

●

The roll-back function does not prevent

fingers or other parts of the body getting

pinched against the window frame. Risk of

accident.

●

After switching off, it is still possible to

open or close the sunroof during a short

space of time provided that neither the

driver nor passenger door is opened.

Window anti-trap function

The roll-back function reduces the risk of in-

jury when the electric windows close.

Sunroof

CAUTION

●

If a window is obstructed when closing au-

tomatically, the window stops at this point

and lowers immediately

●

To prevent damage, during winter tem-

Introduction

peratures remove any ice or snow that

might be on the car roof before opening

the sunroof or adjusting the tilt position.

.

›››

The sunroof consists of two glass parts. The

rear part is fixed and cannot be opened. It al-

so has a sun blind.

●

Next, check why the window does not

close before attempting it again.

●

Before leaving the vehicle or in case of

rainfall, always close the sunroof. With the

sunroof open or in a tilted position, water

can enter the interior and can cause con-

siderable damage to the electrical system.

As a result, other damage can occur in the

vehicle.

●

If you try within the following 10 seconds

The sunroof only works when the ignition is

switched on. Once the ignition has been

switched off, you can still open or close the

sunroof for a few minutes provided the driver

door and the front passenger door are not

opened.

and the window closes again with difficulty or

there is an obstruction, the automatic clos-

ing will stop working for 10 seconds.

●

If the window is still obstructed, the win-

dow will stop at this point.

112

Opening and closing

Raising, opening and closing the sunroof

Convenience function to open or

close the sunroof

Note

Opening the sunroof:

●

Leaves and other loose objects that ac-

cumulate on the sunroof rails should be

regularly cleaned away either by hand or

with a vacuum.

●

Automatic movement: slide your finger

back over the functional area 

›››

●

A

Fig. 89

.

●

If the sunroof does not work correctly,

Manual movement: slide back over the

the anti-trap function will not work either.

Contact a specialised workshop.

functional area  and keep it there.

Closing the sunroof:

●

Automatic movement: slide your finger

A

Operating the sunroof

forward over the functional area 

.

●

Manual movement: slide forward over the

functional area  and keep it there.

Fig. 90 Door handle: sensor surface.

Raising the sunroof:

The sunroof can be opened and closed with

the convenience function, just like the win-

dows.

●

The sunroof can only be raised if it is

closed.

●

Automatic movement: press briefly in the

B

Using the door lock

centre of the functional area 

●

Hold the key in the door lock of the driver

Closing the sunroof when raised:

door in either the unlocking or locking posi-

tion to open or close the roof in the tilted

position. Release the key to interrupt this

function.

●

Automatic movement: slide your finger

Fig. 89 On the interior roof lining: sunroof

button.

A

forward over the functional area 

press briefly in the centre of the functional

or

B

area 

.

Functional area  can be operated in two

Using the remote control

ways: sliding and pressing.

Stop the automatic opening or closing

movement:

●

Keep the locking or unlocking button

Sliding: The roof is opened or closed totally

pressed to open or close the roof. If you re-

lease the button is the opening or closing will

stop.

or partially.

●

Press again on the functional area .

Pressing: The roof is raised, opened or

closed totally or partially. Press again to stop

the automatic movement.

»

113

Operation -> Opening and closing for Your Cupra Formentor SUV First Generation (2020-2024)

Related Topics

Popular Owner Manuals

Latest Owner Manuals