Get Emergency situations -> If you have a flat tyre (with spare tyre) Guide for Hyundai Bayon SUV Second Generation (2021-2024)

08

IF YOU HAVE A FLAT TYRE (WITH SPARE TYRE, IF EQUIPPED)

WARNING

Changing a tyre can be dangerous.

Follow the instructions in this sec-

tion when changing a tyre to reduce

the risk of serious injury or death.

CAUTION

Be careful as you use the jack han-

OAC3073004TU

dle to stay clear of the flat end. The

flat end has sharp edges that could

cause cuts.

The jack is provided for emergency tyre

changing only.

Turn the winged hold down bolt coun-

terclockwise to remove the spare tyre.

Jack and tools

Store the spare tyre in the same com-

partment by turning the winged hold

down bolt clockwise.

To prevent the spare tyre and tools

from “rattling”, store them in their prop-

er location.

OAC3079028TU

(1) Jack

(2) Jack handle

(3) Wheel lug nut wrench

(4) Towing hook

OAC3073005TU

The jack, jack handle, wheel lug nut

wrench, and towing hook are stored in

the luggage compartment under the

luggage box cover.

If it is hard to loosen the tyre hold-down

wing bolt by hand, you can loosen it

easily using the jack handle.

1.Put the jack handle (1) inside of the

tyre hold-down wing bolt.

2.Turn the tyre hold-down wing bolt

counterclockwise with the jack han-

dle.

8-15

Emergency situations

Changing tyres

WARNING

A vehicle can slip or roll off of a jack

causing serious injury or death to

you or those nearby. Take the fol-

lowing safety precautions:

• Do not get under a vehicle that is

supported by a jack.

OAC3073006TU

• NEVER attempt to change a tyre in

the lane of traffic. ALWAYS move

the vehicle completely off the road

on level, firm ground away from

traffic before trying to change a

tyre. If you cannot find a level, firm

place off the road, call a towing

service for assistance.

[A] : Block

5. Block both the front and rear of the

tyre diagonally opposite of the tyre

you are changing.

• Be sure to use the jack provided

with the vehicle.

• ALWAYS place the jack on the

designated jacking positions on

the vehicle and NEVER on the

bumpers or any other part of the

vehicle for jacking support.

• Do not start or run the engine

whilst the vehicle is on the jack.

OAC3073007TU

6. Loosen the wheel lug nuts counter-

clockwise one turn each in the order

shown above, but do not remove any

lug nuts until the tyre has been raised

off of the ground.

• Do not allow anyone to remain in

the vehicle whilst it is on the jack.

• Keep children away from the road

and the vehicle.

Follow these steps to change your vehi-

cle’s tyre :

1. Park on a level, firm surface.

2. Move the shift lever into N (Neutral,

for Automated manual transmission

vehicle) or neutral (for Manual trans-

mission vehicle), apply the parking

brake, and place the ignition switch

in the LOCK/OFF position.

3. Press the hazard warning flasher

button.

4. Remove the wheel lug nut wrench,

jack, jack handle, and spare tyre

from the vehicle.

8-16

08

9. Loosen the lug nuts with the wheel

lug nut wrench and remove them

with your fingers. Remove the wheel

from the studs and lay it flat on the

ground out of the way. Remove any

dirt or debris from the studs, mount-

ing surfaces, and wheel.

10. Install the spare tyre onto the studs

of the hub.

11. Tighten the lug nuts with your fin-

gers onto the studs with the smaller

end of the lug nuts closest to the

wheel.

12. Lower the vehicle to the ground by

turning the jack handle counter-

clockwise.

OAC3073008TU

7. Place the jack at the designated

jacking position under the frame

closest to the tyre you are changing.

The jacking positions are plates

welded to the frame with two notch-

es. Never jack any other position or

part of the vehicle. Doing so may

damage the side seal molding or

other parts of the vehicle.

OAC3073027TU

13. Use the wheel lug nut wrench to

tighten the lug nuts in the order

shown. Double-check each lug nut

until they are tight. After changing

tyres, we recommend that a HYUN-

DAI authorised repairer tighten the

lug nuts to their proper torque as

soon as possible. The wheel lug

nut should be tightened to 11-13

kgf.m (79-94 lbf.ft).

OAC3073009TU

8. Insert the jack handle into the jack

and turn it clockwise, raising the

vehicle until the tyre clears the

ground. Make sure the vehicle is sta-

ble on the jack.

8-17

Emergency situations

If you have a tyre gauge, check the tyre

pressure (see “Tyres and Wheels” in

chapter 2 for tyre pressure instruc-

tions.). If the pressure is lower or higher

than recommended, drive slowly to the

nearest service station and adjust it to

the recommended pressure. Always

reinstall the valve cap after checking or

adjusting tyre pressure. If the cap is not

replaced, air may leak from the tyre. If

you lose a valve cap, buy another and

install it as soon as possible. After

changing tyres, secure the flat tyre and

return the jack and tools to their proper

storage locations.

If any of the equipment such as the

jack, lug nuts, studs, or other equip-

ment is damaged or in poor condition,

do not attempt to change the tyre and

call for assistance.

Use of compact spare tyres

(if equipped)

Compact spare tyres are designed for

emergency use only. Drive carefully on

the compact spare tyre and always fol-

low the safety precautions.

WARNING

To prevent compact spare tyre fail-

ure and loss of control possibly

resulting in an accident:

NOTICE

• Check the tyre pressure as soon

as possible after installing a spare

tyre. Adjust it to the recommended

pressure.

• Use the compact spare tyre only in

an emergency.

• NEVER operate your vehicle over

50 mph (80 km/h).

• Check and tighten the wheel lug

nuts after driving 30 mi. (50 km) if

tyres are replaced. Re-check the

tyre wheel lug nuts after driving

over 600 mi. (1,000 km).

• Do not exceed the vehicle’s maxi-

mum load rating or the load carry-

ing capacity shown on the sidewall

of the compact spare tyre.

• Do not use the compact spare tyre

continuously. Repair or replace

the original tyre as soon as possi-

ble to avoid failure of the compact

spare tyre.

CAUTION

Your vehicle has metric threads on

the studs and lug nuts. Make certain

during tyre changing that the same

nuts that were removed are rein-

stalled. If you have to replace your

lug nuts make sure they have metric

threads to avoid damaging the studs

and ensure the wheel is properly

secured to the hub. We recommend

that you consult a HYUNDAI autho-

rised repairer for assistance.

8-18

08

When driving with the compact spare

tyre mounted to your vehicle:

CAUTION

To prevent damaging the compact

spare tyre and your vehicle:

• Check the tyre pressure after install-

ing the compact spare tyre. The com-

pact spare tyre should be inflated to

60 psi (420 kPa).

• Do not take this vehicle through an

automatic car wash whilst the com-

pact spare tyre is installed.

• Do not use the compact spare tyre on

any other vehicle because this tyre

has been designed especially for

your vehicle.

• Drive slowly enough for the road

conditions to avoid all hazards,

such as a potholes or debris.

• Avoid driving over obstacles. The

compact spare tyre diameter is

smaller than the diameter of a con-

ventional tyre and reduces the

ground clearance about 25 mm (1

in.).

• Do not use tyre chains on the com-

pact spare tyre. Because of the

smaller size, a tyre chain will not fit

properly.

• The compact spare tyre’s tread life is

shorter than a regular tyre. Inspect

your compact spare tyre regularly

and replace worn compact spare

tyres with the same size and design,

mounted on the same wheel.

• Do not use more than one compact

spare tyre at a time.

• Do not tow a trailer whilst the com-

pact spare tyre is installed.

• Do not use the compact spare tyre

on any other wheels, nor should

standard tyres, snow tyres, wheel

covers or trim rings be used with

the compact spare wheel.

• Do not suddenly accelerate or

decelerate (0  25 mph) (0  40

km/h) in any driving mode. It may

cause leakage of transfer oil.

NOTICE

When the original tyre and wheel are

repaired and reinstalled on the vehi-

cle, the lug nut torque must be set

correctly. The correct lug nut tight-

ening torque is 11-13 kgf.m (79-94

lbf.ft).

8-19

Emergency situations

Jack label

OAC3073038TU

The actual Jack label in the vehicle may

differ from the illustration.

For more detailed specifications, refer

to the label attached to the jack.

1. Model Name

2. Maximum allowable load

3. When using the jack, set your park-

ing brake.

4. When using the jack, stop the en-

gine.

5. Do not get under a vehicle that is

supported by a jack.

7. When supporting the vehicle, the

base plate of jack must be vertical

under the lifting point.

8. Shift into R (Reverse) gear on vehi-

cles with Manual transmission or

move the shift lever to the N (Neu-

tral) position on vehicles with Auto-

mated manual transmission.

9. The jack should be used on firm lev-

el ground.

10. Representative company and add-

ress

6. The designated locations under the

frame

8-20

08

EC Declaration of conformity for Jack

Type A

JACKDOC14S

8-21

Emergency situations

Type B

OAC3N070039TU

8-22

08

UK Declaration of conformity for Jack

OAC3073039TU

8-23

Emergency situations -> If you have a flat tyre (with spare tyre) for Your Hyundai Bayon SUV Second Generation (2021-2024)

Related Topics

Popular Owner Manuals

Latest Owner Manuals