Get Emergency situations -> If you have a flat tyre (with Tyre Mobility Kit) Guide for Hyundai Bayon SUV Second Generation (2021-2024)

Emergency situations

IF YOU HAVE A FLAT TYRE (WITH TYRE MOBILITY KIT,

IF EQUIPPED)

CAUTION

When two or more tyres are flat, do

not use the tyre mobility kit because

the sealant provided with the Tyre

Mobility Kit must be used for only

one flat tyre.

WARNING

OAC3073010TU

Do not use the Tyre Mobility Kit to

repair punctures in the tyre walls.

This can result in an accident due to

tyre failure.

For safe operation, carefully read and

follow the instructions in this manual

before use.

(1) Compressor

(2) Sealant bottle

WARNING

The Tyre Mobility Kit is a temporary fix

to the tyre and we recommend that the

system be inspected by a HYUNDAI

authorised repairer.

The tyre inflation pressure must be

at least 32 psi (220 kPa). If it is not,

do not continue driving.

Call for road side service or towing.

8-24

08

Air pressure loss in the tyre may

Introduction

adversely affect tyre performance.

With the Tyre Mobility Kit you stay

mobile even after experiencing a tyre

puncture.

The system of compressor and sealing

compound effectively and comfortably

seals most punctures in a passenger

car tyre caused by nails or similar

objects and reinflates the tyre.

After you ensured that the tyre is prop-

erly sealed you can drive cautiously on

the tyre (distance up to 120 miles (200

km)) at a max. speed of 50 mph (80

km/h) in order to reach a service station

or tyre dealer to have the tyre replaced.

For this reason, you should avoid

abrupt steering or other driving

manoeuvres, especially if the vehicle is

heavily loaded or if a trailer is in use.

The Tyre Mobility Kit is not designed or

intended as a permanent tyre repair

method and is to be used for one tyre

only. This instruction shows you step by

step how to temporarily seal the punc-

ture simply and reliably.

Read the section “Notes on the safe

use of the Tyre Mobility Kit”.

It is possible that some tyres, especially

with larger punctures or damage to the

sidewall, cannot be sealed completely.

WARNING

Do not use the TMK if a tyre is

severely damaged by driving run flat

or with insufficient air pressure.

Only punctured areas located within

the tread region of the tyre can be

sealed using the TMK.

8-25

Emergency situations

• Provided the car is outdoors, leave

the engine running. Otherwise oper-

ating the compressor may eventually

drain the car battery.

• Never leave the Tyre Mobility Kit

unattended whilst it is being used.

• Do not leave the compressor running

for more than 10 min. at a time or it

may overheat.

Notes on the safe use of the

Tyre Mobility Kit

• Park your car at the side of the road

so that you can work with the Tyre

Mobility Kit away from moving traffic.

• To be sure your vehicle will not move,

even when you’re on fairly level

ground, always set your parking

brake.

• Do not use the Tyre Mobility Kit if the

ambient temperature is below -30°C

(-22°F).

• In case of skin contact with the seal-

ant, wash the area thoroughly with

plenty of water. If the irritation per-

sists, seek medical attention.

• Only use the Tyre Mobility Kit for

sealing/inflation passenger car tyres.

Only punctured areas located within

the tread region of the tyre can be

sealed using the tyre mobility kit.

• Do not use on motorcycles, bicycles

or any other type of tyres.

• In case of eye contact with the seal-

ant, flush your eyes for at least 15

minutes. If the irritation persists, seek

medical attention.

• In case of swallowing the sealant,

rinse the mouth and drink plenty of

water. However, never give anything

to an unconscious person and seek

medical attention immediately.

• When the tyre and wheel are dam-

aged, do not use Tyre Mobility Kit for

your safety.

• Use of the Tyre Mobility Kit may not

be effective for tyre damage larger

than about 0.24 in. (6 mm).

If the tyre cannot be made roadwor-

thy with the Tyre Mobility Kit, we rec-

ommend that you contact a HYUND-

AI authorised repairer.

• Do not use the Tyre Mobility Kit if a

tyre is severely damaged by driving

run flat or with insufficient air pres-

sure.

• Long time exposure to the sealant

may cause damage to bodily tissue

such as kidney, etc.

• Do not remove any foreign objects

such as nails or screws that have

penetrated the tyre.

8-26

08

Components of the Tyre Mobility Kit

OAX081006

1. Speed-restriction label

2. Sealant bottle and label with speed restriction

3. Filling hose from sealant bottle to wheel

4. Connectors and cable for the power outlet direct connection

5. Holder for the sealant bottle

6. Compressor

7. ON/OFF switch

8. Pressure gauge for displaying the tyre inflation pressure

9. Button for reducing the tyre inflation pressure

10.Hose to connect compressor and sealant bottle or compressor and wheel

Connectors, cable and connection hose are stored in the compressor housing.

Strictly follow the specified sequence, otherwise the sealant may escape under

high pressure.

8-27

Emergency situations

WARNING

Expired sealant

Do not use the Tyre sealant after the

sealant has expired (for example,

pasted the expiration date on the

sealant container). This can increase

the risk of tyre failure.

WARNING

OAX081008

Sealant

2. Screw connection hose (10) onto the

connector of the sealant bottle.

• Keep out of reach of children.

• Avoid contact with eyes.

• Do not swallow.

Using the Tyre Mobility Kit

CAUTION

OAX081009

3. Insert the sealant bottle into the

housing (5) of the compressor so

that the bottle is upright.

OAC3073011R

Detach the speed restriction label (1)

from the sealant bottle (2), and place

it in a highly visible place inside the

vehicle such as on the steering

wheel to remind the driver not to

drive too fast.

1. Shake the sealant bottle (2).

OAC3079012TU

4. Unscrew the valve cap from the

valve of the defective wheel and

screw the filling hose (3) of the seal-

ant bottle onto the valve.

8-28

08

CAUTION

Securely install the sealant filling

hose to the valve. If not, sealant may

flow backward, possibly clogging

the filling hose.

Tyre pressure

Do not attempt to drive your vehicle

if the tyre pressure is below 200 kPa

(29 psi). This could result in an acci-

dent due to sudden tyre failure.

7. Switch off the compressor.

8. Detach the hoses from the sealant

bottle connector and from the tyre

valve.

Return the Tyre Mobility Kit to its stor-

age location in the vehicle.

WARNING

OAC3073013R

Carbon monoxide

5. Plug the compressor power cord (4)

into the vehicle power outlet.

Do not leave your vehicle running in

a poorly ventilated area for extended

periods of time. Carbon monoxide

poisoning and suffocation can

occur.

NOTICE

Only use the front passenger side

power outlet when connecting the

power cord.

6. With the ignition switch in the ON

position, switch on the compressor

and let it run for about 5~7 minutes

to fill the sealant up to proper pres-

sure. (refer to Tyre and Wheels,

chapter 2). The inflation pressure of

the tyre after filling is unimportant

and will be checked/corrected later.

Be careful not to overinflate the tyre

and stay away from the tyre when

filling it.

8-29

Emergency situations

Distributing the sealant

Checking the tyre inflation

pressure

OLMF064106

9. Immediately drive about 4-6 miles

(7-10 km or, about 10min) to evenly

distribute the sealant in the tyre.

Do not exceed a speed of 50 mph (80

km/h). If possible, do not fall below a

speed of 12 mph (20 km/h).

Whilst driving, if you experience any

unusual vibration, ride disturbance or

noise, reduce your speed and drive

with caution until you can safely pull off

of the side of the road.

OAC3079012TU

1. After driving about 4-6 miles (7-10

km or about 10 min.), stop at a safety

location.

2. Connect the filling hose (3) of the

compressor directly to the tyre valve.

3. Plug the compressor power cord into

the vehicle power outlet.

4. Adjust the tyre inflation pressure to

the recomended tyre inflation.

Call for road side service or towing.

With the ignition swithched on, pro-

ceed as follows.

- To increase the inflation pres-

sure: Switch on the compressor.

To check the current inflation pres-

sure setting, briefly switch off the

compressor.

- To reduce the inflation pressure:

Press the button (9) on the com-

pressor.

8-30

08

CAUTION

NOTICE

Do not let the compressor run for

more than 10 minutes, otherwise the

device will overheat and may be

damaged.

Tyre pressure sensor

(if equipped with TPMS)

The sealant on the tyre pressure

sensor and wheel should be removed

when you replace the tyre with a new

one and inspect the tyre pressure

sensors. We recommend that you

get this done at a HYUNDAI autho-

rised repairer.

Information

i

The pressure gauge may show higher

than actual reading when the compres-

sor is running. To get an accurate tyre

reading, the compressor needs to be

turned off.

Information

i

When reinstalling the repaired or

replaced tyre and wheel on the vehicle,

tighten the wheel lug nut to 11-13

kgf·m (79-94 lbf·ft).

CAUTION

If the inflation pressure is not main-

tained, drive the vehicle a second

time, refer to Distributing the seal-

ant. Then repeat steps 1 to 4.

Use of the Tire Mobility Kit may be

ineffectual for tyre damage larger

than about 0.24 in. (6 mm ).

We recommend that you contact a

HYUNDAI authorised repairer if the

tyre cannot be made roadworthy

with the Tyre Mobility Kit.

WARNING

The tyre inflation pressure should

meet the standard “TYRES AND

WHEELS” in Chapter 2 or “Tyre

Inflation Pressure Standard Label”

on the B pillar of the driver’s seat.

If it is not, do not continue driving.

Call for road side service or towing.

8-31

Emergency situations -> If you have a flat tyre (with Tyre Mobility Kit) for Your Hyundai Bayon SUV Second Generation (2021-2024)

Related Topics

Popular Owner Manuals

Latest Owner Manuals