Get Getting to know your vehicle Guide for Renault Scenic 4 Door Fifth Generation (2023-2026)

VEHICLE E-TECH 100% ELECTRIC (EV)

2

2 0 - G e t t i n g t o k n o w y o u r v e h i c l e

VEHICLE E-TECH 100% ELECTRIC (EV)

Introduction

Electric vehicles have special fea-

tures, but operate in a similar man-

ner to conventional vehicles.

2

The main difference in electric vehi-

cles is the exclusive use of electric

energy instead of fuel, as used in

convention vehicles.

We therefore recommend that you

read these instructions describing

your electric vehicle carefully.

G e t t i n g t o k n o w y o u r v e h i c l e - 2 1

VEHICLE E-TECH 100% ELECTRIC (EV)

Electric vehicle schematic diagram

2

2 2 - G e t t i n g t o k n o w y o u r v e h i c l e

VEHICLE E-TECH 100% ELECTRIC (EV)

1. Electric charging connection (passenger side)

2. "400 V" traction battery

3. Electric motor

2

4. Orange electrical power cables

5. 12 V battery

G e t t i n g t o k n o w y o u r v e h i c l e - 2 3

VEHICLE E-TECH 100% ELECTRIC (EV)

ergy required to operate vehicle

equipment (lights, windscreen

wipers, braking assistance, etc.).

Batteries

Connected services

Introduction

The electric vehicle has two types of

battery:

– a "400 V" traction battery;

– a "12 V" battery.

2

Your electric vehicle has connected

services that provide information

and/or control:

"400 V" traction battery

This battery stores the energy nec-

essary to operate the motor in your

electric vehicle properly. As with any

battery, it discharges after use, and

must be regularly recharged.

You do not have to wait until the

traction battery hits the reserve lev-

el in order to recharge it.

Charging times vary depending on

the type of specific wall unit socket

or public terminal you connect to.

Your vehicle range will depend on

the traction battery charge level

and also on your driving style ꢀ 187.

– your vehicle's charging status with

low battery warning;

– the traction battery charging pro-

gramming, based on certain choices

on offer;

– remaining vehicle range;

– ...

You can access these services us-

ing:

– external digital devices (mobile

phone, tablet, etc.);

– the vehicle multimedia screen.

For more information, refer to the

multimedia equipment instructions

or contact an Approved Dealer.

The A symbol identifies the electri-

cal components in your vehicle

which may present safety risks.

The vehicle's air conditioning sys-

tem is used to cool the traction bat-

tery.

You can subscribe to a

connected service or ex-

tend it at any time by con-

sulting an authorised dealer

To preserve the lifetime of your trac-

tion battery, have your air condition-

ing system checked by a qualified

professional. Especially if you notice

a reduction in air conditioning per-

formance.

12 volt battery

The second battery on your vehicle

is a 12 V battery: this supplies the en-

2 4 - G e t t i n g t o k n o w y o u r v e h i c l e

VEHICLE E-TECH 100% ELECTRIC (EV)

the vehicle and recharge the battery

"400 V" electrical circuit

ꢀ 185.

The vehicle drive sys-

tem in an electric vehi-

cle uses a direct volt-

age of approximately

Bad weather, flooded roads:

2

Do not drive through

floods if the depth of wa-

ter is above the lower

edge of the wheel rims.

400 volts.

This system can get hot during

and after switching off the igni-

tion. Respect warning mes-

sages given on the labels in the

vehicle.

All interventions or modifica-

tions to the 400V electrical sys-

tem (components, cables, con-

nectors, traction battery) are

strictly prohibited due to the

risks they present to your safe-

ty. Call an approved dealer.

The risk of serious burns or elec-

tric shocks can lead to death.

The engine brake

should under no cir-

cumstances be used as

a substitute for the

brake pedal.

The "400 V" electrical circuit can be

recognised by orange cables 9 and

Noise

Electric vehicles are particularly qui-

et. You will not yet necessarily be

used to it, and neither will other road

users. It is difficult for them to hear

the vehicle when it is moving.

parts bearing the

symbol.

Driving

As the motor is silent, you will hear

noises that you are not used to hear-

ing (aerodynamic noises, tyre noise,

etc.)

Each time the ignition is switched

off, the ventilation will be switched

off after about ten seconds.

As with a car with an automatic

gearbox, you will have to get used to

not using your left foot, and not us-

ing this foot to brake.

When driving, if you lift your foot off

the accelerator pedal or depress the

brake pedal, the motor generates

electrical current during decelera-

tion and this energy is used to brake

G e t t i n g t o k n o w y o u r v e h i c l e - 2 5

VEHICLE E-TECH 100% ELECTRIC (EV)

Consult an approved dealer.

Driver obstruction

On the driver's side, on-

ly use mats suitable for

the vehicle, attached

with the pre-fitted components,

and check the fitting regularly.

Do not lay one mat on top of an-

other.

Your electric vehicle is

silent. Before leaving it,

with your foot on the

brake, stop the engine.

2

RISK OF SERIOUS INJURY

There is a risk of wedging the

pedals

Pedestrian horn

The pedestrian horn enables you to

warn others of your presence – espe-

cially pedestrians and cyclists.

When the engine is started, the

pedestrian horn is activated auto-

matically. The sound is emitted

when the vehicle speed is between

approximately 1 and 19 mph (1 and 30

km/h).

For further information on the

pedestrian horn, refer to the multi-

media instructions.

In the event of a pedestrian horn

malfunction, the

warning light

is illuminated on the instrument pan-

el accompanied by the "Exterior

sound fault" message.

2 6 - G e t t i n g t o k n o w y o u r v e h i c l e

VEHICLE E-TECH 100% ELECTRIC (EV)

Important recommendations

2

Please read these instructions carefully. Failure to follow these instructions may lead to a risk of fire, serious

injury or electric shocks which could result in death.

In the event of an accident or impact

In the event of an accident or an impact to the underside of the vehicle (e.g. striking a post, raised kerb or

other street furniture) the electric circuit or the traction battery may be damaged.

Have the vehicle checked by an authorised dealer.

Never touch the "400 V" components or orange cables which are exposed and visible inside or outside the vehicle.

In the event of serious damage to the traction battery, leaks may occur:

– never touch liquids (fluids, etc.), coming from the traction battery;

– in the event of contact with the body, wash the affected area with plenty of water and consult a doctor as soon as

possible.

In the event of an impact, even slight, against the charging flap and/or valve, have them checked by an authorised

dealer as soon as possible.

In the event of fire

In the event of fire, make everyone evacuate the vehicle immediately and contact the emergency services, inform-

ing them that this is an electric vehicle.

If you have to intervene, only use ABC or BC extinguishing agents that are suitable for extinguishing fires on electri-

cal systems. Do not use water or other extinguishing agents.

In the event of damage to the electrical circuit, please call an authorised dealer.

All towing operations

ꢀ 356.

Washing the vehicle

Never wash the engine compartment, the charging connection or the traction battery with a high-pressure jet.

This risks damaging the electric circuit.

Never wash the vehicle while it is charging. Never wash the charging cable while the vehicle is charging. Never wash

the charging cable and the charging cable plug while the cable is not connected, in order to prevent corrosion of the

charging pins.

G e t t i n g t o k n o w y o u r v e h i c l e - 2 7

VEHICLE E-TECH 100% ELECTRIC (EV)

Risk of electric shock and a risk to life.

2

2 8 - G e t t i n g t o k n o w y o u r v e h i c l e

2

G e t t i n g t o k n o w y o u r v e h i c l e - 2 9

VEHICLE E-TECH 100% ELECTRIC (EV)

Charging

Schematic diagram

2

3 0 - G e t t i n g t o k n o w y o u r v e h i c l e

VEHICLE E-TECH 100% ELECTRIC (EV)

1. Specific wall socket or charging terminal.

2. Charging cable.

3. Electric charging socket (passenger side).

2

If you have any questions regarding the equipment needed for charging, please ask an authorised dealer.

Important recommendations for charging your vehicle

Please read these instructions carefully. Failure to follow these instructions may lead to a risk of fire, serious

injury or electric shocks which could result in death.

Charging

Do not do anything to the vehicle during charging (washing, working in the engine compartment, etc.).

In the event of the presence of water, signs of corrosion or foreign bodies in the charging cord connector or in the ve-

hicle charging socket, do not charge the vehicle. Fire hazard.

Do not attempt to touch the cord contacts, the domestic socket or the vehicle charging socket, or introduce objects

into them.

Never plug the charging cord into an adapter, multiple socket or extension lead.

The use of generators is prohibited.

Do not remove or change the vehicle charging socket or the charging cord. Fire hazard.

Do not modify or perform any action on the installation during charging.

In the event of an impact, even slight, against the charging flap or valve, have them checked by an authorised dealer

as soon as possible.

Take care of the cable: do not tread on it, immerse it in water, pull on it or let anything knock against it.

Check regularly that the charging lead is in good condition.

In the event of damage to the charging lead (corrosion, browning, cuts, etc.), to the unit or to the vehicle's electrical

charging socket, do not use them. Please see an authorised dealer to replace them.

In the event of non-activation of the charging flap locking mechanism and/or unlocking of the vehicle's electric

charging socket, please contact an approved dealer.

G e t t i n g t o k n o w y o u r v e h i c l e - 3 1

VEHICLE E-TECH 100% ELECTRIC (EV)

Charging lead B

Charging lead A

Before cleaning the

charging lead, make sure

the lead is disconnected.

2

Clean the cable using a cloth

slightly dampened with water.

When cleaning, make sure that

the cloth does not come into

contact with the ends of the ca-

ble (connectors, charging pins)

to avoid any risk of corrosion.

Each charging lead is

stored in the luggage

compartment of the vehi-

cle ꢀ 69.

This lead can be used for:

This lead is specific to your vehicle

and designed for connecting to wall

sockets or public terminals to enable

standard charging of the traction

battery.

– in normal use, on a socket used on-

ly for the vehicle (14 A/16 A charging);

– occasional charge using a domes-

tic socket, (8 A charge) when you are

not at home, for example.

In all cases, sockets must be fitted

as stated in the instructions provid-

ed with the charging lead B .

We recommend that you

use a charging cord that

enables a standard

charge to charge the traction

battery.

3 2 - G e t t i n g t o k n o w y o u r v e h i c l e

VEHICLE E-TECH 100% ELECTRIC (EV)

2

In all cases, read the charging lead B

user instructions carefully.

Never leave the socket

hanging by the cord. Use

the hooks C to hang it.

If a malfunction occurs

during the charging

process (red warning light

appears on the unit D ), stop

charging immediately. Please

refer to cord instructions.

G e t t i n g t o k n o w y o u r v e h i c l e - 3 3

VEHICLE E-TECH 100% ELECTRIC (EV)

Important recommendations

2

Important recommendations for charging your vehicle

Please read these instructions carefully. Failure to follow these instructions may lead to a risk of fire, serious

injury or electric shocks which could result in death.

Choice of charging cord

The standard charging cords supplied with the vehicle have been designed specifically for this vehicle. It is designed

to protect you against the risks of electric shock that can lead to death or fire.

Do not use with the charging leads of previous vehicles as they are not adapted.

For safety reasons, the use of a charging cord not recommended by the manufacturer is strictly forbidden. Failure to

follow this instruction can lead to risks of fire or electric shock that can prove fatal. For information on a charging

cord suited to your vehicle, please consult an authorised dealer.

Using the charging lead B

Please read the instructions that come with the charging lead carefully to learn about the precautions you must

take when using the product and the technical specifications required for fitting the socket.

Installation

Wall socket

Have a special wall socket installed by a qualified professional.

In the case of domestic charging

Have a qualified professional check that each socket to which you will connect the charging cable complies with

the standards and regulations in force in your country and that it complies with the specifications described in the

information on "Power supply systems".

Power supply systems

Only use charging terminals which conform to the IEC 61851-1 standard and connecting points protected by:

– a Type A 30 mA residual current device specific to the socket used;

– an overcurrent protection device;

– protection against overvoltage relating to lightning in exposed areas (IEC 62305-4);

– an earth connection that complies with the standards in the relevant country.

3 4 - G e t t i n g t o k n o w y o u r v e h i c l e

2

G e t t i n g t o k n o w y o u r v e h i c l e - 3 5

VEHICLE E-TECH 100% ELECTRIC (EV)

Charging types that conform to

European standards

2

Alternating current (AC)

If the information is displayed on the

vehicle charging flap, follow the in-

structions below.

Before plugging in a charging lead,

check that:

– the colour and one of the letters of

the input socket 1 correspond to the

colour and one of the letters on the

end 4 of the lead;

– the colour and one of the letters of

the input socket 3 correspond to the

colour and one of the letters on the

end 5 of the lead.

3 6 - G e t t i n g t o k n o w y o u r v e h i c l e

VEHICLE E-TECH 100% ELECTRIC (EV)

Labels

Charging type

Alternating current (AC)

2

Charging terminal 1 /Charging ca-

ble 4

Connection

Vehicle 3 /Charging cable 5

Charging types that conform to European

standards (for all other cases, please consult

an approved dealer).

G e t t i n g t o k n o w y o u r v e h i c l e - 3 7

VEHICLE E-TECH 100% ELECTRIC (EV)

Direct current (DC)

If fast-charging the vehi-

cle (DC), the charging ca-

ble between your vehicle

2

and the charging terminal must

not exceed 30 metres.

If in doubt about the length of

the cable, consult the owner of

the charging terminal (DC).

If the information is displayed on the

vehicle charging flap, follow the in-

structions below.

Before plugging in a charging cable,

make sure that the colour and one of

the letters on the inlet socket 3 cor-

respond to the colour and one of the

letters on the end 5 of the charging

cable.

3 8 - G e t t i n g t o k n o w y o u r v e h i c l e

VEHICLE E-TECH 100% ELECTRIC (EV)

Labels

Charging type

Connection

Direct current (DC)

2

Vehicle 3 /Charging cable 5

Charging types that con-

form to European standards

(for all other cases, please

consult an approved deal-

er).

G e t t i n g t o k n o w y o u r v e h i c l e - 3 9

VEHICLE E-TECH 100% ELECTRIC (EV)

and restarting the vehicle if the bat-

tery is cold or warm.

To preserve the service life of your

traction battery, avoid parking the

vehicle for more than one month

with high charge, especially when

the weather is very hot.

Favour charging the traction battery

after driving and/or in mild tempera-

tures. Otherwise, charging may take

a longer period of time or even be-

come impossible.

– the 6

charging cable;

button unlocks the

Electric charging socket 3

2

– button 7

can be used to stop

the charging programme (if previ-

ously configured) in order to start

charging the vehicle immediately.

Precautions

For daily use, it is recommended that

you charge your vehicle to 80% to

improve the battery service life.

Avoid charging and parking your ve-

hicle in extreme temperatures (hot

or cold).

Under extreme conditions, charging

may take several minutes before

starting (time required for the trac-

tion battery to cool down or warm

up).

It is preferable to recharge the vehi-

cle after driving if the charge level is

low (<25%) and in negative tempera-

tures.

Advice

Note: if in a snowy environment, re-

move snow from the vehicle charg-

ing area on the passenger side be-

fore plugging in or disconnecting.

Snow in the socket may block the in-

sertion of the charging cord plug.

The vehicle is equipped with two

charging connections located on

the passenger side at the front of

the vehicle:

– socket E for charging up to 22 kW;

– socket F for fast charging (de-

pending on the vehicle).

– In high temperatures, try to park

and recharge the vehicle in a shad-

ed/sheltered location;

When the vehicle is parked for more

than seven days in temperatures be-

low approximately -25°C, charging

the traction battery can become im-

possible.

If the vehicle is parked for more than

three months with near zero charge,

it may become impossible to charge

the battery.

– charging can be performed in the

rain or snow;

– activating the air-conditioning in-

creases the charging time required.

Recharging the traction battery

Vehicle stationary, ignition off:

– take the charging cable 2 located

in the storage tray in your vehicle's

luggage compartment;

– press the charging flap 8 to unlock

it. The warning light 9 illuminates in

white;

The energy level available depends

on the battery temperature. It may

therefore vary between stopping

There are also two buttons located

inside the charging flap:

4 0 - G e t t i n g t o k n o w y o u r v e h i c l e

VEHICLE E-TECH 100% ELECTRIC (EV)

Depending on the vehicle,

when the charging flap is

open or not properly

Do not use the charging

flap 8 to hang the charg-

ing cable 2 while recharg-

Make sure you fully uncoil

the charging cord to limit

its heating.

2

closed, the "Charging flap

opened" message appears on

the instrument panel.

ing the vehicle.

Do not use an exten-

sion lead, multiple

socket or adapter.

Fire hazard.

If you have just accepted

a system update via the

multimedia system, the

traction battery charging will

be delayed or cancelled.

During charging, the indicator light 9

Wait for the update to be com-

pleted before connecting the

charging lead to the vehicle. For

more information on system up-

dates, please refer to the multi-

media instructions.

flashes in blue.

When charging starts, the following

information is displayed on the in-

strument panel:

– the energy level on the battery in-

dicator light 12 ;

– after you hear a locking click,

check that the charging cord is

properly plugged in. To check the

locking, pull gently on the handle 10 ;

– if you have programmed a de-

ferred charge and you wish to start

charging immediately, press the

button 7 to start charging ꢀ 316.

– plug in the end of the lead to the

power supply;

– grab the handle 10 ;

– plug in the vehicle cord. The warn-

ing light 9 flashes in white;

The charging cord is automatically

locked with the vehicle. This will

make it impossible to unplug the

cord from your vehicle.

G e t t i n g t o k n o w y o u r v e h i c l e - 4 1

VEHICLE E-TECH 100% ELECTRIC (EV)

You do not need to wait until the

charge is at reserve levels to

recharge your vehicle.

The traction battery

charging time depends

on the amount of energy

2

Operating faults

remaining and the power deliv-

ered by the charging terminal.

The information is displayed on

the instrument panel during

charging ꢀ 135.

If the warning light 9 is illuminated

continuously in red, please contact

an approved dealer.

Note: under certain conditions,

the actual charging time may

be longer than the charging

time displayed on the instru-

ment panel. This depends on:

– the battery refill rate;

– the quality of the electrical

network;

– the initial charge level;

– the exterior temperature is

too cold;

– an estimate of the remaining

charging time (this is not displayed

after the battery is charged to ap-

proximately 95%);

– the indicator light 11 indicates that

the vehicle is connected to a power

supply;

– your vehicle range will vary ac-

cording to the charge level.

The display on the instrument panel

disappears after a few seconds. It

reappears on the instrument panel

when a door is opened.

– ...

In the event of a problem with

the charging cable, we recom-

mend that you replace it with a

cable that is identical to the

original. Consult an approved

Dealer.

Precautions to take when removing

from the socket

– Press the button 6 or press and

hold the door unlocking button on

the card in order to release the vehi-

cle charging lead;

One charging is complete, the indi-

cator light 9 is displayed in green.

– grab the handle 10 ;

4 2 - G e t t i n g t o k n o w y o u r v e h i c l e

VEHICLE E-TECH 100% ELECTRIC (EV)

– when it lights up continuously in

green this indicates that the vehicle

is fully charged;

Label 13

It is imperative to follow

the unplugging steps in

order.

– flashes in green: when Vehicle to

Grid (V2G) ꢀ 50 or Vehicle to Load

(V2L) ꢀ 44 is enabled;

2

– when it lights up continuously in

red this indicates an operating fault.

– unplug the charging lead 2 from

the vehicle;

– you must close the charging flap 8

and press on it to lock it;

– disconnect the lead 2 from the

power supply 1 ;

– store the lead 2 in the storage

compartment of your luggage com-

partment.

Note: immediately after a long peri-

od of charging the traction battery,

the lead may be hot. Please use the

handles.

The label 13 located on the charging

flap 8 provides information on the

charging operation according to the

status of the warning light 9 :

After pressing the charg-

ing cable release button,

you will have around 30

– when it flashes in white this indi-

cates that the lead is plugged into

the vehicle and the system is carry-

ing out its checks;

– when it lights up continuously in

blue this indicates that charging

programming is activated;

– flashes in blue: charging is in

progress or the vehicle is using the

mains supply for its operation (e.g.

for passenger compartment air con-

ditioning);

The label 13 located on the right-

hand side reminds you of the follow-

ing instructions:

– do not wash the charging flap us-

ing a high-pressure water jet;

– with the vehicle stationary, the

valve and the charging flap can be

opened;

seconds to unplug it before it is

locked once again.

G e t t i n g t o k n o w y o u r v e h i c l e - 4 3

VEHICLE E-TECH 100% ELECTRIC (EV)

– when the vehicle is being driven,

the valve and the charging flap must

be closed;

– open the flap to connect the

charging lead;

– close the flap again once discon-

nected;

2

– connect to a domestic socket, an

alternating current charging termi-

nal or a quick charging terminal;

– for any information on charging,

please consult your vehicle user

manual.

Vehicle to Load (V2L) function

With the vehicle stationary and the

parking brake applied, the "Vehicle

to Load" (V2L) function allows you to

connect electrical devices directly

to the vehicle.

The system provides AC power (up

to 16 A/3.7 kW) using electrical ener-

gy stored in your vehicle's traction

battery ꢀ 20.

The V2L connector enables you to

connect and operate various electri-

cal devices using the charging sock-

et at the front of your vehicle.

4 4 - G e t t i n g t o k n o w y o u r v e h i c l e

VEHICLE E-TECH 100% ELECTRIC (EV)

Important recommendations

2

Please read these instructions carefully. Failure to follow these instructions may lead to a risk of fire, serious

injury or electric shocks which could result in death.

Precautions to be taken when using the V2L function.

Do not attempt to power your home as this can lead to damage and electric shocks.

Do not wash the vehicle or work in the engine compartment while using the V2L function.

Do not use the V2L function:

– if there is water in the V2L connector or in the vehicle's charging socket;

– if the vehicle's V2L connector or charging input socket is damaged (broken, signs of corrosion, discolouring, etc.),

contact an approved dealer to organise a replacement;

– outdoors, if the weather conditions are unsuitable (rain, risk of lightning, etc.).

Do not place metal objects on the V2L connector.

Do not modify or interfere with the V2L connector while using the V2L function.

Never connect an adapter to the V2L connector.

Precautions to be taken when handling and using the V2L connector.

Use only the V2L connector supplied with the vehicle. The V2L connector has been designed specifically for this vehi-

cle. For your safety, the use of a V2L connector not recommended by the manufacturer is strictly prohibited. For

more information on which V2L connector is right for your vehicle, consult an approved dealer.

Do not rest any objects against the V2L connector and do not hang devices by their power cable from the AC output

socket of the V2L connector. Risk of damage.

Take care of the V2L connector. Do not disassemble it, immerse it in water or pull on it while it is connected and do

not let anything knock against it. Regularly check the condition of the connector before use.

Precautions to be taken when using electrical/electronic devices.

Before plugging in and using a device (extension cable, multi-plugs, etc.), check the precautions for use by referring

to its user manual.

Do not plug in:

– devices that require a direct current, such as medical equipment. The power supply may be interrupted depending

on the vehicle operating conditions;

G e t t i n g t o k n o w y o u r v e h i c l e - 4 5

VEHICLE E-TECH 100% ELECTRIC (EV)

– devices that consume more than 16 A;

– devices that do not comply with national regulations and standards;

– damaged devices (units, cables, etc.);

– devices whose initial recommendations for use are not adapted to the environment in which they will be used

(risks related to contact with dust and water);

2

– more than one multi-plug. When in use, do not connect products that consume more than 8 A;

– an extension lead more than 20 m long. If used, be sure to unwind it completely.

4 6 - G e t t i n g t o k n o w y o u r v e h i c l e

VEHICLE E-TECH 100% ELECTRIC (EV)

Vehicle to Load (VLC) connector

A

Before carrying out main-

tenance on the V2L con-

nector, make sure the

Before connecting or dis-

connecting a device,

make sure that the V2L

connector indicator light 2 is

off.

2

connector is disconnected.

Clean the connector using a

cloth slightly dampened with

water.

When cleaning, make sure that

the cloth does not come into

contact with the ends of the

connector (connectors, charg-

ing pins) to avoid any risk of cor-

rosion.

To connect the V2L connector

With the vehicle stationary, the

opening elements unlocked and the

ignition off:

Operation

1. Charging socket;

2. Operation warning light;

3. On/Off switch;

Ensure that the parking

brake is always applied

when the V2L function

is in use.

4. Protective cover;

5. AC output socket.

You must observe the or-

der in which the V2L con-

nector is connected/dis-

connected.

G e t t i n g t o k n o w y o u r v e h i c l e - 4 7

VEHICLE E-TECH 100% ELECTRIC (EV)

indicator light 2 appears in green.

– an electrical device exceeding the

maximum power capacity is con-

nected;

– the V2L connector switch 3 is

pressed for at least three seconds;

– the minimum charging threshold

of the traction battery set from the

multimedia display is reached.

The V2L function is activated, the in-

dicator light on the charging sock-

et 10 flashes in green and the electri-

cal device is supplied with power.

2

Note: do not pull the handle 8 while

the V2L connector is being locked to

the vehicle.

When the power supply is cut off, a

message will appear on the instru-

ment panel to inform you.

To disconnect the V2L connector

– press the charging flap 9 to unlock

it;

– hold the handle of the connector 8

and connect the end piece 1 of the

connector to the vehicle charging

socket 7 ;

– check that the V2L connector is

correctly connected by pulling light-

ly on the handle 8 . Before the dis-

charge begins, the socket lock is ac-

tivated. The V2L connector is auto-

matically locked to the vehicle. This

makes it impossible to disconnect

the connector from the vehicle;

– connect the electrical device to

the V2L connector AC output sock-

et 5 ;

When in use, the following informa-

tion is displayed on the instrument

panel:

– the indicator light 11 to indicate

that the vehicle is connected to the

V2L connector;

– the estimated time 12 remaining

before the minimum battery charg-

ing threshold is reached;

– the battery energy level 13 .

Note: the power supply automatical-

ly shuts off when:

– the V2L function is not used for

about an hour (no electrical devices

connected to the AC socket 5 of the

V2L connector or no power con-

sumption);

With the card on you or the vehicle

opening elements unlocked:

– press the button 6

located

– press the V2L connector switch 3

for at least three seconds until the

next to the charging socket to stop

the discharging. The indicator light 2

4 8 - G e t t i n g t o k n o w y o u r v e h i c l e

VEHICLE E-TECH 100% ELECTRIC (EV)

goes out, the indicator light on the

charging socket 10 goes out and the

V2L function is deactivated;

– the V2L connector is automatically

unlocked with the vehicle. This en-

ables the connector to be discon-

nected from your vehicle;

– disconnect your electrical device

and hold the handle 8 of the V2L

connector to disconnect it from the

vehicle within approximately 15 sec-

onds. Otherwise, the charging sock-

et 7 will be locked again automati-

cally;

impossible V2L to check" message

will be displayed on the instrument

panel: disconnect the electrical de-

vice and disconnect the V2L connec-

tor. Consult an approved Dealer.

In the event of a failure of the V2L

function from the device connected

to the AC socket of the V2L connec-

tor, the "V2L discharge impossible

Connected device fault" message is

displayed on the instrument panel:

– disconnect the electrical device

and the V2L connector;

– check that the device and V2L

connector are not damaged and

that the power supply plug is not

broken or corroded;

Settings

2

– close the charging flap 9 and

press on it to lock it;

– place the V2L connector in its stor-

age area.

You can set the minimum charge

threshold level of the traction bat-

tery from the multimedia screen 14 .

Please refer to the multimedia in-

structions for further information.

– make sure that the electrical de-

vice does not exceed the maximum

capacity of power that the vehicle

can provide.

If there is still a problem, contact an

approved dealer.

Do not drive the vehicle

while the charging flap 9

is open. Once the V2L con-

nector is disconnected from the

vehicle, make sure that the

charging flap 9 is properly

closed.

Operating faults

In the event of an operating mal-

function, the indicator light 2 on the

V2L connector will go out and the

V2L (discharge) power supply will

switch off automatically. A message

is displayed on the instrument panel

to inform you.

In the event of an internal failure of

the V2L function, the "V2L discharge

G e t t i n g t o k n o w y o u r v e h i c l e - 4 9

VEHICLE E-TECH 100% ELECTRIC (EV)

world 2 on the multimedia screen 1 ,

Charging programming

press the "Electric" menu 3 to pro-

gramme the charging and/or com-

fort of your vehicle.

If you have just accepted

a system update via the

multimedia system, the

2

You can use the "Programmes" tab

to:

traction battery charging will

be delayed or cancelled.

– add a new charging programme;

or

– access pre-saved charging pro-

grammes.

Please refer to the multimedia in-

structions for further information.

Wait for the update to be com-

pleted before connecting the

charging lead to the vehicle.

For more information on system

updates, please refer to the

multimedia instructions.

For safety reasons, car-

ry out these operations

when the vehicle is sta-

tionary.

Vehicle to Grid (V2G) charging

Depending on the vehicle, with the

vehicle stationary and connected

using your vehicle's charging cable,

the Vehicle to Grid (V2G) charging al-

lows you to redistribute the energy

stored in your vehicle's battery to

your home and to the power grid.

You must have a compatible two-

way AC charging terminal and have

subscribed to the V2G charging ser-

vice. Please refer to the multimedia

instructions for further information.

When the programming is con-

firmed, the indicator light

lights up on the instrument panel.

Note: charging will start if the engine

is switched off, the vehicle is con-

nected to a power supply and ac-

cess is authorised.

With the vehicle stationary and the

engine running, from the "Vehicle"

5 0 - G e t t i n g t o k n o w y o u r v e h i c l e

VEHICLE E-TECH 100% ELECTRIC (EV)

Disconnect your vehi-

cle before carrying out

any work or modifica-

tion on the electrical in-

stallation.

2

To set up V2G charging,

refer to the multimedia

user manual.

G e t t i n g t o k n o w y o u r v e h i c l e - 5 1

CARD

– automatically closing the electric

windows remotely ꢀ 65;

tally lock or unlock the vehicle by in-

advertently pressing the buttons on

the card.

Note: if a door or the luggage com-

partment door is open or not proper-

ly shut, the vehicle will not be locked.

A beep sounds and the hazard warn-

ing lights and side repeaters do not

flash.

General information

– automatically opening the electric

windows remotely ꢀ 65.

2

Depending on the vehicle,

you may have a digital

key that offers all the

functions of the card. However,

if a card has been left inside the

vehicle and the doors have

been locked with a digital key,

all of the card's functions will be

inhibited.

If the battery is flat, you

can still lock/unlock and

start your vehicle ꢀ 169

ꢀ 65 ꢀ 52.

For further information, please

see the "Digital key" section

ꢀ 61.

"Remote lighting" function

1. Unlocking the doors and luggage

compartment.

2. Locks all the opening elements.

3. Unlocking/locking the boot.

Range

Make sure that the correct battery

type is being used, and that the bat-

tery is in good condition and insert-

ed correctly. Its service life is ap-

proximately two years: it should be

replaced when the "Keycard Battery

Low" message appears on the in-

strument panel ꢀ 52.

4. Switching on the lighting remote-

ly.

The card is used for:

– locking/unlocking the opening ele-

ments (doors, luggage compart-

ment door) and folding out or folding

in the front door handles;

– unlocking the charging flap ꢀ 20;

– switching on the vehicle lighting

remotely;

card operating range

This varies according to the sur-

roundings: take care not to acciden-

5 2 - G e t t i n g t o k n o w y o u r v e h i c l e

CARD

Press button 4 to switch on the

dipped beam headlights and the ex-

terior lighting for approximately 20

seconds. This can be used, for exam-

ple, to identify the vehicle from a dis-

tance when parked in a car park.

Press and hold button 4 for approxi-

mately two seconds to switch on the

exterior lighting and emit a sound.

Replacement: need for an

additional card

Driver's responsibility

when parking or stop-

ping the vehicle

If you lose your card or re-

quire another, you can obtain

one from an approved Dealer.

If a card is replaced, it will be

necessary to take the vehicle

and all its cards to an approved

Dealer to initialise the system.

You may use up to four cards

per vehicle.

2

Never leave an animal,

child or adult who is not self-suf-

ficient alone in your vehicle,

even for a short time.

They may pose a risk to them-

selves or to others by starting

the engine, activating equip-

ment such as the electric win-

dows or locking the doors.

Also, in hot and/or sunny weath-

er, please remember that the

temperature inside the passen-

ger compartment increases

very quickly.

Note: press button 4 again to switch

off the lighting.

Recommendations

Avoid leaving the card in

hot, cold or humid areas.

Do not keep the card in a place

where it could be bent or dam-

aged accidentally, such as in

your back pocket.

Interference

Interference by factors in the imme-

diate vicinity (external installations

or the use of equipment operating

on the same frequency as the re-

mote control) may affect the opera-

tion of the remote control.

RISK OF DEATH OR SERIOUS IN-

JURY.

G e t t i n g t o k n o w y o u r v e h i c l e - 5 3

CARD

Insert the hand strap into the com-

ponent 8 and pass the end of the

strap through the buckle.

Position the strap at the opening 6

and close the casing.

Fitting a hand strap 7

Do not store the card any-

where it may come into

contact with other elec-

tronic equipment (computer,

phone etc.) as this could hinder

its operation.

2

Note: check that the diameter of the

hand strap cord 7 fits the opening 6 .

Use

Deactivating/activating the

"hands-free" mode

Depending on the vehicle, you can

deactivate/activate unlocking when

approaching and locking when mov-

ing away from the vehicle.

You can also deactivate/activate

the sound signal that is emitted up-

on locking when moving away from

the vehicle ꢀ 139.

Slide the rear casing 5 downwards

while pressing on area A .

Never leave your vehi-

cle with the card inside.

There are two ways to unlock/lock

the vehicle:

– in "hands-free" mode, when ap-

proaching and moving away from

the vehicle;

– using the card in remote control

mode.

5 4 - G e t t i n g t o k n o w y o u r v e h i c l e

CARD

"Hands-free" unlocking when

approaching the vehicle

"Hands-free" locking when mov-

ing away from the vehicle

Driver's responsibility

when parking or stop-

ping the vehicle

2

Never leave an animal,

child or adult who is not self-suf-

ficient alone in your vehicle,

even for a short time.

They may pose a risk to them-

selves or to others by starting

the engine, activating equip-

ment such as the electric win-

dows or locking the doors.

Also, in hot and/or sunny weath-

er, please remember that the

temperature inside the passen-

ger compartment increases

very quickly.

With the card in the access zone 1 ,

With the card on you and the doors

and luggage compartment door

closed, move away from the vehicle:

it will be locked automatically as

soon as you leave the access zone 1 .

The front handles are folded in and

the hazard lights flash twice then re-

main illuminated for about four sec-

onds, then a beep sounds to indicate

that the doors have locked and, on

some vehicles, the door mirrors fold

in automatically.

the vehicle will be unlocked.

RISK OF DEATH OR SERIOUS IN-

JURY.

The front handles are folded out and

the hazard lights and side repeaters

flash once to indicate that the doors

have unlocked and, on some vehi-

cles, the door mirrors fold out auto-

matically.

Note: the distance at which the vehi-

cle locks depends on the surround-

ings.

G e t t i n g t o k n o w y o u r v e h i c l e - 5 5

CARD

– if the card remains close to vehicle

zone 1 during approximately five

minutes after the vehicle has been

locked;

– after several passes in the vicinity

of zone 1 without the doors having

been unlocked.

"Hands-free" unlocking by open-

ing the luggage compartment

2

Press the luggage compartment

door opening button 4 or use the

card as a remote control to unlock

the vehicle and reactivate "hands-

free" mode.

Special features relating to

"hands-free" locking

After locking in "hands-free" mode,

you have to wait approximately

three seconds to be able to unlock

the vehicle again. During these three

seconds, the door handles can be

tried to make sure that the vehicle is

locked properly.

Note: if a door or the luggage com-

partment door is open or not proper-

ly shut, the vehicle will not be locked.

A beep sounds but the hazard warn-

ing lights and side repeaters do not

flash.

If the card has been within the de-

tection zone 1 for approximately 15

minutes, remote locking is deacti-

vated. To lock the vehicle, press the

button 3 on the card.

The vehicle cannot be remotely

locked if the card is within the zone

2 .

With the card in the zone 1 and the

vehicle locked, press button 4 once

to unlock the entire vehicle.

The front handles are folded out and

the side indicator lights and hazard

warning lights flash once to indicate

that the doors have unlocked.

Special features of the unlocking

system

Under certain circumstances, un-

locking when approaching the vehi-

cle is deactivated:

– if the vehicle has not been used for

eight days;

5 6 - G e t t i n g t o k n o w y o u r v e h i c l e

CARD

With the doors and luggage com-

partment door closed, press button

3 : the vehicle will be locked.

Using the card as a remote con-

trol

The front handles fold in and the

hazard lights and side repeaters

flash twice to indicate that the

doors have locked and, on some ve-

hicles, the door mirrors fold in auto-

matically.

2

Depending on the vehicle, press but-

ton 3 twice to lock the vehicle. Press

and hold button 3 to close the front

and rear windows.

Note:

– the maximum distance at which

the vehicle locks depends on the sur-

roundings;

– if a door or the boot is open or not

properly shut, locking is not carried

out. A beep sounds but the hazard

warning lights and side repeaters do

not flash.

While the engine is running, if the

card is no longer in zone 2 after a

door is opened and closed, the "Key-

card Not Detected" message indi-

cates that the card is no longer in-

side the vehicle. This will, for exam-

ple, prevent you from driving away

after dropping off a passenger who

has kept the card on them.

Unlocking with the card

Press the button 5 .

The front handles are folded out and

the side indicator lights and hazard

warning lights flash once to indicate

that the doors have unlocked.

The warning disappears when the

card is detected again.

The card buttons are de-

activated when the en-

gine is running.

Locking using the card

G e t t i n g t o k n o w y o u r v e h i c l e - 5 7

CARD

approaching the vehicle will be func-

tional again.

Unlocking/locking the luggage

compartment only

Deadlocking

2

Driver's responsibility

when parking or stop-

ping the vehicle

Never leave an animal,

child or adult who is not self-suf-

ficient alone in your vehicle,

even for a short time.

They may pose a risk to them-

selves or to others by starting

the engine, activating equip-

ment such as the electric win-

dows or locking the doors.

Also, in hot and/or sunny weath-

er, please remember that the

temperature inside the passen-

ger compartment increases

very quickly.

If the vehicle is equipped with a

deadlocking function, this allows

you to lock the opening elements

and to prevent the doors from being

unlocked using the interior handles

(for example, by breaking the win-

dow and then trying to open the

door from the inside).

In the case of a vehicle equipped

with a manual (non-motorised) tail-

gate, press the button 6 to unlock/

lock the luggage compartment only.

Note: after unlocking the luggage

compartment only using button 6 , to

unlock the other opening elements it

is necessary:

RISK OF DEATH OR SERIOUS IN-

JURY.

– to press button 5 ;

or

– to move away from the vehicle in

order to activate the automatic

locking when moving away from the

vehicle. In this case, unlocking when

Unlocking the charging cable

Never use deadlocking

if someone is still inside

the vehicle.

Press button 5 to unlock the vehicle

charging cable.

5 8 - G e t t i n g t o k n o w y o u r v e h i c l e

CARD

To activate deadlocking

"Hands-free" card: battery

Replacing the battery

Press button 2 twice in quick suc-

cession.

2

Locking is confirmed by two slow

flashes and three quick flashes of

the hazard warning lights and side

indicator lights.

Depending on the vehicle, the door

mirrors may fold in automatically

when the vehicle is locked ꢀ 148.

To deactivate deadlocking

Press the button 1 once.

The hazard warning lights flash

once to indicate that the doors have

been unlocked.

To refit, proceed in the reverse order

then press one of the buttons on the

card four times while you are near

the vehicle: the next time the vehicle

is started, the message will disap-

pear.

When the "Keycard Battery Low"

message appears on the instrument

panel, replace the card battery:

– slide the rear casing 1 downwards

while pressing on area A ;

– remove the battery cover 2 ;

– remove the battery by pressing on

one side and lifting the other;

– replace it according to the direc-

tion and template indicated inside

the cover.

Check that the cover is clipped shut.

Note: when replacing the battery, do

not touch the electronic circuit or

contacts on the card.

G e t t i n g t o k n o w y o u r v e h i c l e - 5 9

CARD

Operating faults

The batteries are avail-

able from approved Deal-

ers, and their service life

Precautions relating to

batteries:

If the battery is too weak to ensure

correct operation, you will still be

able to start and lock/unlock the ve-

hicle ꢀ 65.

2

– keep batteries (new

or used) out of reach of children;

– do not swallow batteries;

approximately two years.

Check that there is no dye on

the battery: risk of an incorrect

electrical contact.

Risk of chemical burns which

may lead to death.

– if ingested or inserted into

any part of the body, consult a

doctor as soon as possible.

If they need to be re-

placed, be sure to use

the same or equivalent

type of battery (consult

an Approved Dealer).

When replacing:

– make sure that the

batteries are correctly

inserted.

Do not throw away your

used batteries as rubbish.

Take them to an ap-

Risk of explosion.

proved Dealer or consult your

local authority for information

on appropriate recycling facili-

ties.

– if the flap does not close cor-

rectly, do not use the card and

keep out of reach of children.

6 0 - G e t t i n g t o k n o w y o u r v e h i c l e

DIGITAL KEY

Secure access to the digi-

tal key on the smartphone

It is the responsibility of

The digital key's opera-

tional reach will depend

on your smartphone's

General information

Depending on the country and sub-

scription, you can install a digital key

for your vehicle on your smartphone.

The digital key contains the rights

required to lock/unlock and start

your vehicle using a smartphone.

Thus, your smartphone replaces

your card.

The installation, administration and

transmission of the digital keys are

carried out using the manufacturer's

app.

2

the owner of the digital key and

the designated users to protect

and secure access to the digital

key on the smartphone.

Make sure that you install the

necessary security and protec-

tion tools on your smartphone

(such as securing the screen

with a password).

Bluetooth® connection.

Lending a digital key

From the manufacturer's app, ac-

cess the "Share Virtual Key " menu

and fill in the information for the oc-

casional user. After validation, a

confirmation email will be sent to

the user.

Once the manufacturer's applica-

tion is installed on your smartphone

and the subscription is activated,

the digital key must be activated

from the manufacturer's applica-

tion.

Operating conditions

Activate Bluetooth® on your smart-

phone then open the

In the event of vehicle

lending, the owner of the

digital key is responsible

for designating a trusted per-

son as another user of the vehi-

cle.

manufacturer's application to ac-

cess the various digital key func-

tions.

Note: the smartphone must be suffi-

ciently charged in order to use a digi-

tal key. In the event of a low charge

level, the "Low phone battery" mes-

sage appears on the instrument

panel.

If you need to entrust your

vehicle to somebody else,

make sure you have the

To avoid any error in the transmis-

sion of a digital key to an occasional

user (for example: lack of WIFI or mo-

bile network, etc.), be sure to antici-

pate the lending procedure.

vehicle card with you to guaran-

tee access to the vehicle (e.g. in

the context of an intervention

on the vehicle, an appointment

with an approved dealer or a

qualified professional, etc.).

To do this, make sure that:

– the manufacturer's application

has previously been downloaded

and installed by the occasional user;

G e t t i n g t o k n o w y o u r v e h i c l e - 6 1

DIGITAL KEY

– your smartphone and the occa-

sional user's smartphone are con-

nected to the internet throughout

the procedure (via WIFI or mobile

networks);

– the occasional user's digital key is

activated once the procedure is

completed.

– deadlocking (depending on the ve-

hicle): please see "Hands-free card:

deadlocking" ꢀ 58;

Locking/unlocking the doors

and luggage compartment,

deadlocking, remote lighting

The first time the vehicle is unlocked

or started using a new digital key or

a new smartphone, it will take sever-

al seconds for the vehicle to identify

the digital key installed on your

smartphone.

From your smartphone, with Blue-

tooth® activated, open the

manufacturer's application and dis-

cover the various functions avail-

able for your digital key. They are

identical to those of your card.

– remote lighting: please see the in-

formation on the "Remote lighting"

function ꢀ 52;

2

– remote sounding of the horn (al-

lows you to identify the vehicle from

afar or when parked in a crowded

car park, for example);

– starting/stopping the engine:

please see "Starting, stopping the

engine" ꢀ 169.

Revoking a digital key

The user can individually revoke a

digital key. Once a digital key has

been revoked, the user can activate

a new key.

For more information, please see the

manufacturer's application.

Starting, stopping the engine

Special features related to unlock-

ing the opening elements

Activation/deactivation from

the multimedia screen

It is possible to deactivate and reac-

tivate the "Digital key" function so

that the vehicle does not communi-

cate with any digital key. Please re-

fer to the multimedia instructions.

Under certain circumstances (e.g.

after eight days of the vehicle not

being used), it is not possible to un-

lock the vehicle using a digital key:

press the luggage compartment

opening button then unlock your ve-

hicle using your digital key.

Note: deactivating the function will

not delete existing digital keys. It on-

ly deactivates the vehicle's capacity

to communicate with them.

These functions are:

– locking/unlocking all the opening

elements: please see "Hands-free

card: use" ꢀ 52;

– locking/unlocking the luggage

compartment (depending on the ve-

hicle): please see "Hands-free card:

use" ꢀ 52;

Upon first use and each time a new

smartphone is used, it is necessary

6 2 - G e t t i n g t o k n o w y o u r v e h i c l e

DIGITAL KEY

to calibrate your digital key with

your vehicle.

To do this, activate Bluetooth® on

your smartphone then follow the

procedure from the manufacturer's

application.

and holding. Without a smartphone

or card, you will not be able to start

the vehicle again.

It is necessary to place

the smartphone in the

placement area in order

to start and stop the engine and

when calibrating.

2

Special features of the digital

key

When calibrating, the smartphone

must be placed in the placement

area 1 .

To start/stop the engine, the system

checks that the smartphone is

present in the placement area 1 be-

fore allowing the engine to be start-

ed.

– For the digital key to remain ac-

tive, the smartphone concerned

must be connected to the Internet

(via WIFI or mobile network) at least

once every 48 hours. Otherwise, con-

nect your smartphone to the inter-

net for a few minutes so that the dig-

ital key can be reactivated.

– If a card has been left inside the

vehicle and the doors have been

locked with the digital key, all of the

card's functions will be inhibited. The

card's functions will remain inactive

until the engine is started again.

In this case, to start the engine you

will need to use either the digital key

or a card other than that left inside

the vehicle.

For more information, please refer to

the information on "Starting, stop-

ping the engine" ꢀ 169.

The smartphone must remain in the

vehicle throughout the journey.

Note:

If a digital key has been lent, you can

delete it by carrying out the revoking

procedure using the smartphone

while it is placed in the placement

area 1 .

Otherwise, the deletion request is

left pending and is only confirmed

once the engine is started using an-

other digital key or a card.

If the smartphone is no longer in the

passenger compartment when you

try to switch the engine off, a mes-

sage is displayed on the instrument

panel: press and hold the engine

start/stop button 2 for more than

two seconds.

If the smartphone is no longer in the

passenger compartment, make sure

you can retrieve it before pressing

When the engine is start-

ed or stopped, the smart-

phone should always be

sufficiently charged in order to

use the digital key.

G e t t i n g t o k n o w y o u r v e h i c l e - 6 3

DOORS AND OPENING ELEMENTS

The handle can be brought out man-

ually as well as electrically To do this,

move the lock cover 2 and grip the

end A of the handle 1 using your fin-

ger.

Opening and closing the

doors

2

Opening from the outside

Front doors and rear doors

As a safety precaution,

the doors should only

be opened/closed

when the vehicle is sta-

tionary.

Opening from the inside

The front doors and rear doors are

equipped with handles that fold out

and in automatically according to

the vehicle status:

– when the vehicle is unlocked, the

handles fold out to allow access to

the vehicle;

– when the vehicle is locked, the

handles fold in;

– above 3 mph (5 km/h), the handles

fold in;

– when reversing, the handles fold

in.

Once deployed, the handles fold in

automatically after about three min-

utes if no action is performed on the

opening elements.

Pull the handle 3 .

From inside the vehicle, the front ex-

terior handles can be folded out:

6 4 - G e t t i n g t o k n o w y o u r v e h i c l e

DOORS AND OPENING ELEMENTS

– by opening a door;

and a beep will sound for around

– by pressing the central locking

button once when the vehicle is

locked or twice when it is unlocked.

40 seconds or until the door(s) or lug-

Driver's responsibility

when parking or stop-

ping the vehicle

gage compartment are closed.

Special feature

2

When driving, the handles fold in au-

tomatically:

Never leave an animal,

Once the engine has been switched

off, the lights and accessories (radio,

etc.) will continue to operate until

the driver’s door is opened.

child or adult who is not self-suf-

ficient alone in your vehicle,

even for a short time.

– as soon as the vehicle speed ex-

ceeds approximately 3 mph (5 km/

h);

They may pose a risk to them-

selves or to others by starting

the engine, activating equip-

ment such as the electric win-

dows or by locking the doors.

Also, in hot and/or sunny weath-

er, please remember that the

temperature inside the passen-

ger compartment increases

very quickly.

– when reversing.

Child safety

Lights-on reminder buzzer

A warning beep sounds when the

driver's door is opened to warn you

that the lights are still on.

Door or luggage compartment

lid open buzzer

When the vehicle is stationary, the

RISK OF DEATH OR SERIOUS IN-

JURY.

warning light appears on the

instrument panel accompanied by a

warning light indicating which of the

opening elements (door(s), luggage

compartment) are open or incor-

rectly closed.

Locking, unlocking the open-

ing elements and doors

To make it impossible for the rear

doors to be opened from the inside,

lower the lever 4 and check from the

inside that the doors are securely

locked.

If the card does not work:

Once the vehicle reaches a speed of

approximately 12 mph (20 km/h), a

warning light indicates if the door(s)

or luggage compartment are open

or not properly closed, along with

the "WARNING: Boot Open" or

In certain cases, the card may not

work:

– when the card battery is worn, the

battery is flat, etc;

"WARNING: Door Open" message

G e t t i n g t o k n o w y o u r v e h i c l e - 6 5

DOORS AND OPENING ELEMENTS

– due to the use of electronic de-

vices near to the remote control (e.g.

mobile telephone);

The built-in key 2 is used to lock or

unlock the front left-hand door if the

card is not working.

Using the key integrated in the

card

– the vehicle is located in a high

electromagnetic radiation zone;

– vehicle locked using a digital key

ꢀ 61.

2

Access with key 2

It is then possible:

– to use the key that is built into the

card;

– to lock each of the doors manually;

– to use the interior door locking/un-

locking control;

– to use the digital key ꢀ 61, depend-

ing on the vehicle.

The card's built-in key

Move the lock cover 3 by pressing

the left part and insert the key 2 into

the lock in order to lock or unlock the

driver's door.

Slide the rear casing 1 downwards

while pressing on area A .

6 6 - G e t t i n g t o k n o w y o u r v e h i c l e

DOORS AND OPENING ELEMENTS

Locking the doors manually

Interior locking/unlocking door

control

Door and tailgate status indica-

tor

With the ignition on, the switch 5

warning light indicates the locking

status of the opening elements:

2

– when the warning light is on, the

doors and luggage compartment

door are locked;

– indicator light off, the doors and

tailgate are unlocked.

If the ignition is off, when you lock

the doors the warning light remains

lit for some time before disappear-

ing.

After locking/unlocking

the vehicle using the but-

tons on the card, the re-

mote locking and "hands-free"

unlocking modes are deactivat-

ed.

With the door open, turn the screw 4

(using the end of the key) and close

the door.

This means that the door is then

locked from the outside.

The doors may then only be opened

from the inside or by using the key in

the front left-hand door.

The switch 5 simultaneously con-

trols the doors and the luggage

compartment door.

If a door or the tailgate is open or not

closed properly, the doors and tail-

gate lock/unlock quickly.

If transporting an object with the

luggage compartment door open,

you can still lock the doors: with the

ignition off, press and hold the

switch 5 for more than five seconds

to lock the other opening elements.

To reactivate the "hands-free"

mode, restart the vehicle.

Locking the doors without the

card

For example, in the event of a dis-

charged battery or the card tem-

porarily not working, etc.

G e t t i n g t o k n o w y o u r v e h i c l e - 6 7

DOORS AND OPENING ELEMENTS

With the ignition switched off and a

Activating/deactivating the

function

Automatic locking when dri-

door or the luggage compartment

door open, press and hold the switch

5 for more than five seconds.

ving

To activate it: with the vehicle sta-

tionary and the engine running,

press switch 1 for at least five sec-

onds until you hear a beep.

Operating principle

2

When the door is closed, all the doors

and tailgate will be locked.

Note: unlocking the vehicle from the

outside is only possible while the

card is in the vehicle's access zone

or using the key that is built into the

card.

To deactivate it: with the vehicle

stationary and the engine running,

press switch 1 for at least five sec-

onds until you hear two beeps.

The function can also be activated

and deactivated via the multimedia

screen ꢀ 139 (depending on the vehi-

cle).

Never leave your vehi-

cle with the card inside.

Operating faults

If you experience an operating fault

(no central locking, the switch light 1

does not light up when trying to lock

the doors and luggage compart-

ment, etc.), make sure that central

locking has not been deactivated by

mistake and check that all of the

opening elements are properly

closed. If they are properly closed,

contact an approved dealer.

Driver's responsibility

If you decide to keep

the doors locked when

After the vehicle is started, the sys-

tem automatically locks the doors

when you reach approximately 6

mph (10 km/h).

The door can be unlocked:

– by pressing the door unlocking

switch 1 ;

you are driving, remem-

ber that it may be more difficult

for those assisting you to gain

access to the passenger com-

partment in the event of an

emergency.

– at a standstill, by opening a front

door from inside the vehicle.

Note: if a door is opened/closed, it

will automatically lock again when

the vehicle reaches a speed of ap-

proximately 6 mph (10 km/h).

6 8 - G e t t i n g t o k n o w y o u r v e h i c l e

DOORS AND OPENING ELEMENTS

– access the luggage compartment

by folding down the rear bench

seatback(s);

Closing

Driver's responsibility

If you decide to keep

the doors locked when

Lower the luggage compartment lid,

depending on the vehicle, initially us-

ing the inside handle to assist you.

– insert a flat-blade screwdriver or

similar tool at the emergency open-

ing lever 2 and slide it to the left as

shown on the drawing;

2

you are driving, remem-

ber that it may be more difficult

for those assisting you to gain

access to the passenger com-

partment in the event of an

emergency.

Never use the struts to

close the luggage com-

partment door.

– push the boot lid to open it.

The attaching of any

carrying device (bike

Opening manually from inside

the vehicle

rack, luggage box, etc.)

resting on the luggage

compartment lid is prohibited.

To install a carrying device on

your vehicle, contact an Ap-

proved Dealer.

Luggage compartment

Opening

Automatic tailgate

Conditions of use

– Immobilise the vehicle.

– If there is any ice or snow prevent-

ing the tailgate from opening, this

ice or snow must be removed to free

the tailgate.

– In the event that the battery is dis-

charged or if it is replaced, the tail-

gate should be closed (manually if

necessary) to restart the tailgate

motor.

If it is impossible to unlock the lug-

gage compartment, it can be done

manually from inside:

Press button 1 and lift the luggage

compartment door.

G e t t i n g t o k n o w y o u r v e h i c l e - 6 9

DOORS AND OPENING ELEMENTS

Opening/Closing

Driver's responsibility

when parking or stop-

ping the vehicle

To avoid damaging the

tailgate system, do not

manually force the tail-

gate to open or close while it is

moving.

The opening or closing of the auto-

matic tailgate is indicated by three

sound signals.

2

Never leave your vehi-

cle with a child, an adult who is

not self-sufficient or a pet inside

or at the rear of the tailgate,

even for a short while.

They may pose a risk to them-

selves or to others by starting

the engine, activating equip-

ment such as the electric win-

dows, the automatic tailgate or

by locking the doors.

Ensure that nobody is

close to the moving

parts when opening/

closing the tailgate.

Risk of injury.

using the remote control card

Depending on the equipment, the

tailgate locks and unlocks at the

same time as the doors.

The following modes are available to

manoeuvre the tailgate:

RISK OF DEATH OR SERIOUS IN-

JURY.

– using the card as a remote control;

– using the controls on the bumper

and the tailgate;

It is prohibited to at-

tach any carrying de-

vice (bicycle rack, car-

go box, etc.) resting on

the tailgate.

To install a carrying device on

your vehicle, contact an ap-

proved dealer.

– using the dashboard control.

As a safety precaution,

the doors should only

be opened/closed

when the vehicle is sta-

tionary.

With the engine off, press and hold

the switch 1 on the card while near

the luggage compartment.

Risk of injury.

7 0 - G e t t i n g t o k n o w y o u r v e h i c l e

DOORS AND OPENING ELEMENTS

Using the tailgate exterior open-

ing control

Using the tailgate interior clos-

ing control

Using the dashboard control

2

To open the tailgate, press and hold

the switch 4 until you hear the sig-

nal, then release the switch immedi-

ately.

Press the control 2 .

Press the control 3 .

Note: if the switch is not released

quickly enough (within approximate-

ly one second) after the beep, the

tailgate will not open. In this case, re-

peat the sequence.

To close the tailgate, press and hold

the switch 4 until the tailgate closes

completely. A beep sounds through-

out the operation.

Note: if you let go of the switch 4 be-

fore the tailgate is completely

closed, the closing operation is inter-

rupted.

G e t t i n g t o k n o w y o u r v e h i c l e - 7 1

DOORS AND OPENING ELEMENTS

– open the tailgate to an intermedi-

ate position;

– manually adjust the tailgate to the

chosen position;

– press the motorised tailgate con-

trol 3 for more than three seconds to

store the position.

Stopping the tailgate manoeu-

vre

The obstacle detection

is an aid to opening

and closing the tail-

gate, it does not in any

way replace the user's care or

responsibility.

The movement of the motorised tail-

gate can be stopped at any time by

briefly pressing on one of the open-

ing/closing controls.

If the tailgate is stationary in the in-

termediate position, your next press

2

Two beeps will sound to notify you

that the setting has been saved.

When opening/closing the tail-

gate:

will move the tailgate in the opposite

direction to when you stopped it.

– check that nobody is near any

of the moving parts;

User precautions

– Before opening/closing the tail-

gate, ensure that the surrounding

space is sufficient to allow the tail-

gate to operate.

– Avoid multiple manual stops dur-

ing the automatic tailgate move-

ment (risk of damaging the tailgate

system).

Manual mode

– small objects may not be de-

tected. Ensure that no body

parts (arms, hands, fingers etc.)

are near the moving tailgate

parts.

After stopping the tailgate, you can

perform the manoeuvre manually if

you wish.

You can switch to the automatic

manoeuvre at any time by pressing

one of the controls.

The detection of obstacles is

deactivated at the end of the

movement, before the tailgate

is fully closed. If something gets

stuck, stop the movement by

pressing briefly on one of the

opening/closing controls.

Risk of serious injury.

Obstacle detection

Operating faults

If the tailgate detects an obstacle

during its manoeuvre then it will

stop. It will then be released from the

obstacle following a small move-

ment in the opposite direction, be-

fore stopping completely.

If you operate the automatic tail-

gate continuously for about a

minute (a series of openings and

closings), it locks to prevent over-

heating. The system becomes oper-

ational again after about a minute.

Press a tailgate opening/closing

control to resume the tailgate oper-

ation.

The automatic tailgate will not oper-

ate if the battery is on low charge. In

this case, operate the automatic

tailgate with the engine running.

Note: in very cold weather condi-

tions, the automatic opening may

Limiting the tailgate opening an-

gle

You can adjust the maximum tail-

gate opening height It will always

stop at the chosen position:

7 2 - G e t t i n g t o k n o w y o u r v e h i c l e

DOORS AND OPENING ELEMENTS

not work if the tailgate seals are

frozen.

2

G e t t i n g t o k n o w y o u r v e h i c l e - 7 3

FACIAL RECOGNITION

face, insufficient lighting, etc.), the

system suggests the profile that

was last used.

Note: make sure that the camera is

not obscured (by dirt, mud, etc.).

2

When recalling a posi-

tion (memorisation,

changing profile),

make sure that no one

is near the moving parts (in par-

ticular, in the rear seats).

For safety reasons, carry out

any adjustments when the vehi-

cle is stationary.

After saving your profile from the

multimedia system, it is possible to

recall the driver's user settings (dri-

ving position, etc.) using the camera

A when entering the vehicle.

For more information on storing a

profile using facial recognition,

please refer to the multimedia user

manual.

The system is activated when the

driver's door is closed. As soon as it

detects a saved profile related to

the facial recognition, the pre-con-

figured settings are then activated

(driving position, phone connection,

calendar, etc.).

If the face image is not recognised

by the camera (partially obscured

7 4 - G e t t i n g t o k n o w y o u r v e h i c l e

FRONT SEATS

ton 2 and lift the headrest to release

it.

The headrest is an im-

portant safety compo-

nent: ensure that it is in

Front headrests

To refit the headrest

To raise the headrest

2

place and in the cor-

Check that the headrest rods are

clean 3 .

rect position. The top of your

head should be in line with the

top of the headrest. The dis-

tance between your head and

section A should be as short as

possible.

Insert the headrest rods into the

holes 1 (tilt the seatback back-

wards). Lower the headrest until it

locks and press button 2 to adjust to

the desired height. Check that each

rod 3 is locked on the seatback.

Pull the headrest upwards to the de-

sired height. Check that it is correct-

ly locked.

To lower the headrest

Press the button 2 and guide the

headrest down to the desired height.

Check that the bonnet is correctly

locked.

To remove the headrest

Raise it to its highest position (tilt the

seatback backwards). Press the but-

G e t t i n g t o k n o w y o u r v e h i c l e - 7 5

FRONT SEATS

To raise or lower the seat base

Front seats with manual con-

trol

For safety reasons, car-

ry out any adjustments

while the vehicle is sta-

Move lever 3 as many times as nec-

essary upwards or downwards.

To move the seat forwards or

back

2

tionary.

To tilt the seatback

We would advise you not to re-

cline the seatbacks too far to

ensure that the effectiveness of

the seat belts is not reduced.

Nothing should be placed on

the floor (area in front of the dri-

ver) as these objects may slide

under the pedals during sudden

braking manoeuvres, thus ob-

structing their use.

Raise the handle 4 as far as possible

and tilt the seatback to the desired

position. Release the handle at the

desired position and make sure that

it is locked.

After making adjust-

ments, make sure that

the seatbacks are cor-

rectly locked in place.

Raise the handle 1 to unlock. Release

the handle at the desired position

and make sure that it is locked.

Adjusting the lumbar support on

the driver’s seat

(depending on the vehicle)

Push the switch 2 forwards or back-

wards to adjust the lumbar pad.

7 6 - G e t t i n g t o k n o w y o u r v e h i c l e

FRONT SEATS

For more information on program-

ming this function, please refer to

the multimedia instructions.

Heated seats

2

Front seats with electric con-

trols

– a third press decreases the heat-

ing to minimum power. One integrat-

ed warning light is illuminated;

– a fourth press turns the heating

off.

In order to avoid unnecessary ener-

gy consumption, the heated passen-

ger seat can be deactivated auto-

matically in the absence of an occu-

pant.

Depending on the vehicle, with the

ignition on, you can activate the

heated seats via the multimedia

screen 5 :

– pressing the

pictogram on

Depending on the vehicle, the

driver's front seat is equipped.

Use switch 1 to access the "Seats"

menu on the multimedia screen.

the required seat for the first time

activates the heating system at

maximum power. Three switch-inte-

grated warning lights are illuminat-

ed;

"Favourites" function

Adjusting the seatback

– a second press decreases the

heating to medium power. Two inte-

grated warning lights are illuminat-

ed;

Depending on the vehicle, by press-

ing the steering wheel control 6 , you

can activate the heated seats ac-

cording to the stored user settings

that you have previously defined.

To tilt the seatback, move the top of

switch 2 forwards or backwards.

G e t t i n g t o k n o w y o u r v e h i c l e - 7 7

FRONT SEATS

Adjusting the lumbar support on

Heated seats

the driver’s seat

For safety reasons, car-

ry out any adjustments

while the vehicle is sta-

Move the switch 3 forwards, back-

wards, upwards or downwards.

2

tionary.

Adjusting the seat position

We would advise you not to re-

cline the seatbacks too far to

ensure that the effectiveness of

the seat belts is not reduced.

Nothing should be placed on

the floor (area in front of the dri-

ver) as these objects may slide

under the pedals during sudden

braking manoeuvres, thus ob-

structing their use.

Depending on the vehicle, with the

ignition on, you can activate the

heated seats via the multimedia

screen 5 :

– pressing the

pictogram on

To move the seat forwards or back

Move the switch 4 forwards or back-

wards.

To raise or lower the seat base

Move the rear of the switch 4 up-

wards or downwards.

the required seat for the first time

activates the heating system at

maximum power. Three switch-inte-

grated warning lights are illuminat-

ed;

– a second press decreases the

heating to medium power. Two inte-

grated warning lights are illuminat-

ed;

7 8 - G e t t i n g t o k n o w y o u r v e h i c l e

FRONT SEATS

For more information on program-

ming this function, please refer to

the multimedia instructions.

2

Front seats: functions

– a third press decreases the heat-

ing to minimum power. One integrat-

ed warning light is illuminated;

– a fourth press turns the heating

off.

In order to avoid unnecessary ener-

gy consumption, the heated passen-

ger seat can be deactivated auto-

matically in the absence of an occu-

pant.

"Lumbar activated" function

(depending on the vehicle)

You can activate the "Lumbar acti-

vated" function for the driver's seat

or, depending on the vehicle, for the

front passenger seat.

With the ignition on, from the multi-

media screen select the "Vehicle"

world 1 , "Seats", then "Lumbar acti-

vated".

Browse through the "Driver" or "Pas-

senger" menu to:

A number of seat functions are

available from the multifunction

screen, depending on the vehicle.

On equipped vehicles, the switch A

can be used to directly access the

"Seats" menu on the multimedia

screen.

"Favourites" function

Depending on the vehicle, by press-

ing the steering wheel control 6 , you

can activate the heated seats ac-

cording to the stored user settings

that you have previously defined.

– select the sequence type ("Low",

"Extended", "Alternate");

– adjust the intensity;

– activate/deactivate the massage

seat.

G e t t i n g t o k n o w y o u r v e h i c l e - 7 9

FRONT SEATS

Press and hold the switch A of the

seat for which you would like to acti-

vate the "Lumbar activated" func-

tion, according to the defined para-

meters.

– the passenger seat moves back-

wards when the door is opened and

advances when the door is closed.

The seats move automatically. You

can interrupt the movement by

pressing one of the seat adjustment

buttons 3 , 4 and 5 .

Position

2

Settings

Refer to the multimedia instructions

for information on accessing the

settings.

You can activate or deactivate the

following elements:

– easy driver/passenger access;

– visual feedback of current move-

ment.

Note: if the user profile is "Guest",

the automatic adjustment functions

will not be available.

Deactivate the "Seat

Easy access" function

before installing a child

seat on the front pas-

senger seat and/or on the rear

seats.

Risk of injury.

Seat Easy access

When the function is activated:

– the driver's seat, with the vehicle

stationary:

– moves backwards when the

door is opened (if the engine is off)

or when the engine is switched off

(if the door is open);

– advances when the engine is

started (if the door is closed) or

when the door is closed (if the en-

gine is running);

8 0 - G e t t i n g t o k n o w y o u r v e h i c l e

FRONT SEATS

It is possible to save the driving posi-

tion for the driver's seat and/or pas-

senger seat.

The driving position includes the set-

tings for the seat base and seatback

as well as the exterior rear view mir-

rors.

From the multimedia system, you

can store and recall the driving posi-

tion by pressing buttons 3 , 4 and 5

(ꢀ 77):

You can interrupt the stored driving

position reminder by pressing one of

the seat adjustment buttons 3 , 4

and 5 .

Before using "Relax po-

sition" or recalling a

driving position (posi-

2

tion memory, changing

the profile), ensure that nobody

is near any of the moving parts

(especially on the rear seats).

Risk of injury.

« Relax position »

With the vehicle stationary, you can

move back and tilt the driver's seat

to enable a relaxing seating position

while taking a break: press "Acti-

vate" 2 .

You can interrupt the movement in

progress by pressing one of the seat

adjustment buttons 3 , 4 and 5 or via

the multimedia screen by pressing

"Return to the driving position".

– by changing the user profile;

– by pressing the "Recall" button for

the driver's seat;

– by pressing the buttons 6 for the

passenger seat.

Note: while the vehicle is charging, a

message is automatically displayed

on the multimedia screen to ask if

you would like to activate the posi-

tion. During activation, you can ac-

cess the "Relax position" settings;

For further information on the "Relax

position", please refer to the multi-

media instructions.

Storing your driving position

– Adjust the driver's seat using but-

tons 3 , 4 and 5 ꢀ 77;

– adjust the door mirrors ꢀ 148.

Refer to the multimedia instructions

for information on accessing the

stored driving position.

The positions of the exterior rear

view mirrors when driving forwards,

in reverse and of the driver seat are

saved.

Recalling the driving position

For more information on storing the

driving position, please refer to the

multimedia instructions.

G e t t i n g t o k n o w y o u r v e h i c l e - 8 1

REAR SEATS

Rear bench seat: functions

Functions

Rear headrests

To raise the headrest

2

To remove the headrest 2

Tilt the bench seat forwards then

press button 1 and remove the head-

rest 2 .

To fold down the seatback

Ensure that the front seats are far

enough forward.

Before folding down a seatback, fas-

ten the seat belt. This prevents the

seat belt from locking when the

seatback is lifted up again.

To refit the headrest 2

Tilt the bench seat forwards, then in-

sert the rods into the holes and push

in the headrest 2 until it locks. Check

that it is correctly locked.

Pull the strap 1 and lower the seat-

back A .

8 2 - G e t t i n g t o k n o w y o u r v e h i c l e

REAR SEATS

Make sure the cup holders

and armrest storage cov-

er are closed before han-

2

dling the seats ꢀ 330.

When moving the rear

bench seat, ensure that

nothing obstructs the

anchorage points

(body parts, pets, gravel, cloths,

toys, etc.).

To raise the seatback

Proceed in reverse order.

Raise the seatback again until it

reaches the locking joint of the seat-

back. Be careful not to jam the seat

belt between the seatback and the

parcel shelf.

Check the operation of the seat belt.

Do not use the central

rear seat while the arm-

rest is lowered.

G e t t i n g t o k n o w y o u r v e h i c l e - 8 3

SEAT BELTS

Seat belts

Always wear your seat belt when

travelling in your vehicle. You must

also comply with the legislation of

the particular country you are in.

Adjusting the seat belts

Make sure that the rear

bench seat ꢀ 82 is locked

in position correctly so

that the rear seat belts will op-

erate correctly.

2

Before starting, first adjust your dri-

ving position, then ask all occupants

to adjust their seat belts to ensure

optimum protection.

Incorrectly adjusted or

twisted seat belts may

cause injuries in the

event of an accident.

Use one seat belt per person,

whether child or adult.

Even pregnant women should

wear a seat belt. In this case, en-

sure that the lap belt is not ex-

erting too much pressure on the

abdomen, but do not allow any

slack.

Adjusting your driving position

–

Sit well back in your seat (having

removed your coat or jacket, etc.).

This is essential to ensure that your

back is positioned correctly;

–

adjust the distance between the

To ensure the correct adjustment

and positioning of the seat belts on

all seats:

– adjust the seats (seat position and

seatback angle, if available);

– sit with your back firmly against

the seatback;

seat and the pedals. Your seat

should be as far back as possible

while still allowing you to fully de-

press the pedals. The seatback

should be adjusted so that your

arms are slightly bent when you hold

the steering wheel;

– move the shoulder strap 1 as close

as possible to the base of the neck

without it actually resting against it

(if necessary, adjust the height of

the seat belt if possible) and make

sure that the shoulder strap 1 is in

contact with the shoulder;

– position the lap belt 2 so that it lies

flat on the thighs and against the

pelvis.

–

adjust the position of your head-

rest. For maximum safety, your head

must be as close as possible to the

headrest;

–

adjust the height of the seat. This

adjustment allows you to select the

seat position which offers you the

best possible view;

–

adjust the position of the steering

wheel.

8 4 - G e t t i n g t o k n o w y o u r v e h i c l e

SEAT BELTS

The seat belt must be worn as close

to the body as possible. e.g. avoid

wearing heavy clothing, keeping

bulky objects under the belts, etc.

– symbol in green: seat belt fas-

tened;

– symbol in red: the seat is occupied

and the seat belt is not fastened;

– symbol in grey: seat not occupied.

Seat belt reminder warning

lights

2

Front and rear seat belt reminder

warning

Locking

With the doors closed, the

Unwind the belt slowly and smoothly

and ensure that the buckle 3 locks

into the catch 5 (check that it is

locked by pulling on the buckle 3 ).

If the belt jams, allow it to return

slightly before attempting to unwind

it again.

If your seat belt is completely

jammed, pull slowly, but firmly, so

that just over 3 cm unwinds. Allow it

to return slightly before attempting

to unwind it again.

If there is still a problem, contact an

approved dealer.

warning light appears on the central

display when the vehicle ignition is

switched on if the driver's and/or

passenger's seat belt(s) (if this seat

is occupied) are not fastened.

When the vehicle speed is less than

approximately 12 mph (20 km/h), the

warning light appears on the

central display if a seat is occupied

and the seat belt is not fastened.

It is accompanied by the graphic 6

which appears for approximately 60

seconds each time one of the seat

belts is fastened or unfastened.

When the vehicle speed reaches ex-

ceeds approximately 12 mph (20 km/

h), if one of the seat belts is or be-

comes unfastened during the jour-

ney:

With the doors closed, the graphic 6

is displayed on the instrument panel

for approximately 60 seconds when

the vehicle ignition is switched on.

This informs the driver of the fasten-

ing status of each of the seat belts

every time:

– the doors are opened during dri-

ving (vehicle speed above zero);

– a seat belt is fastened/unfas-

tened.

Unlocking

Press the button 4 and the seat belt

will be rewound by the inertia reel.

Guide the belt.

– the

warning light flashes on

the central display;

and

– a beep sound for approximately

120 seconds;

Understanding the graphic 6 :

G e t t i n g t o k n o w y o u r v e h i c l e - 8 5

SEAT BELTS

and

strap is worn as shown previously.

Press the button 7 and raise or lower

the seat belt. Make sure that the

seat belt is locked in position cor-

rectly after you have adjusted it.

Check that the rear

seat belts are posi-

tioned and operating

correctly each time the

– the graphic 6 is displayed for ap-

proximately 180 seconds and the

symbol for the seat concerned

changes to red.

2

rear bench seat is moved.

Always make sure that the front

passengers are properly fastened in

and that the number of seat belts in-

dicated as fastened corresponds to

the number of seats occupied.

Rear seat belts

Rear side seat belts 8

Rear centre seat belt 9

Note: in some cases, the warnings

may be triggered if an object is

placed on one of the seats.

Adjusting the height of the front

seat belts

The belts are fastened, unfastened

and adjusted in the same way as the

front belts.

Slowly unwind the belt 9 .

Fasten the buckle 10 into the red

catch unit 11 .

Press the button 7 to adjust the seat

belt height, so that the shoulder

8 6 - G e t t i n g t o k n o w y o u r v e h i c l e

SEAT BELTS

Warnings

The following information applies to the vehicle’s front and rear seat belts.

2

– No modification must be made to the originally-fitted restraint system components (seat belts, seats and

their mountings). For special operations (e.g. fitting child seats) please contact an approved dealer.

– Do not use devices which give any slack in the belts (e.g. clothes pegs, clips, etc.), as a seat belt which is

worn too loosely risks causing injury in the event of an accident.

– Never wear the shoulder strap under your arm or behind your back.

– Never use the same belt for more than one person and never hold a baby or child on your lap with your seat belt

around them.

– The belt should never be twisted.

– Following an accident, have the seat belts checked and replaced if necessary. Always replace your seat belts as

soon as they show any signs of wear.

– When the rear bench seat is being put back, make sure that the seat belts and buckles are correctly positioned so

that they can be used properly.

– Make sure that the seat belt buckle is inserted into the appropriate catch.

– Ensure that no objects are placed in the area around the seat belt catch as they could prevent it from being prop-

erly secured.

– Make sure the seat belt catch is properly positioned (it should not be hidden away, crushed or flattened by people

or objects).

G e t t i n g t o k n o w y o u r v e h i c l e - 8 7

ADDITIONAL SAFETY DEVICES

Pretensioners

Methods of restraint in addi-

tion to the front seat belts

– Have the entire re-

straint system checked

following an accident.

2

They consist of:

– seat belt inertia reel pretension-

ers;

– lap seat belt pretensioners;

– chest force limiters;

– airbags driver and passenger

front.

These systems are designed to act

independently or together when the

vehicle is subjected to a frontal im-

pact.

Depending on the severity of the im-

pact, the system can cause:

– blocking of the seat belt;

– the seat belt inertia reel preten-

sioner which is triggered to correct

seat belt slack;

– the lap seat belt pretensioner to

hold the occupant in their seat;

– the front airbag.

– No operation whatsoever is

permitted on any part of the

system (pretensioners, airbags,

computers, wiring) and the sys-

tem components must not be

reused on any other vehicle,

even if identical.

– Only qualified personnel from

our Network may work on the

pretensioners and airbags, oth-

erwise the system may trigger

accidentally and cause injury.

– The electrical trigger system

may only be tested by a special-

ly trained technician using spe-

cial equipment.

The pretensioners hold the seat belt

against the body, holding the occu-

pant more securely against the seat,

thus increasing the seat belt's effi-

ciency.

In the event of a severe frontal im-

pact and if the ignition is switched

on, the system may engage the fol-

lowing depending on the force of the

impact:

– If scrapping your vehicle, con-

tact an approved dealer for dis-

posal of the gas generator of

the pretensioners and airbags.

– the seat belt inertia reel preten-

sioner 1 which instantly retracts the

seat belt;

– the lap seat belt inertia reel pre-

tensioner 2 on the front seats.

Load limiter

Above a certain severity of impact,

this mechanism is used to limit the

force of the belt against the body so

that it is at an acceptable level.

8 8 - G e t t i n g t o k n o w y o u r v e h i c l e

ADDITIONAL SAFETY DEVICES

Driver and passenger front

airbags

Fitted to the driver and passenger

sides.

A symbol on the lower section of the

windscreen indicates if this equip-

ment is present (depending on the

vehicle).

2

Each airbag system consists of:

– an airbag and gas generator fitted

on the steering wheel for the driver

and in the dashboard for the front

passenger;

– an electronic unit for monitoring

the system controlling the gas gen-

erator electrical trigger;

Operation

This system is only operational when

the ignition is switched on.

– remote sensors;

The airbag system us-

es pyrotechnic princi-

ples. This explains why,

– control warning lights, displayed

on the roof console 3 :

In a severe frontal impact, the

airbags inflate rapidly, cushioning

the impact of the driver's head and

chest against the steering wheel

and of the front passenger against

the dashboard. The airbags then de-

flate immediately so that the pas-

sengers are not in any way prevent-

ed from leaving the vehicle.

when the airbag in-

–

lit up, airbag passenger

flates, it will generate heat, pro-

duce smoke (this does not

mean that a fire is about to

start) and sound like a detona-

tion. In a situation where an

airbag deployment is required,

it will inflate immediately and

this may cause some minor, su-

perficial grazing to the skin or

other problems.

activated;

–

lit up, airbag passenger

deactivated.

Operating faults

This warning light comes on

when the engine is started and then

G e t t i n g t o k n o w y o u r v e h i c l e - 8 9

ADDITIONAL SAFETY DEVICES

goes out after approximately 65 sec-

onds.

If it does not come on when the igni-

tion is switched on or if it stays on,

there is a fault in the system.

2

Contact your approved Dealer as

soon as possible;

Your protection will be reduced until

this fault is rectified.

In the event of a frontal impact with

another vehicle of an equivalent or

higher category, with an impact

area equal to or greater than 40%,

where the speed of both vehicles is

equal to or greater than 25 mph (40

km/h).

In a side impact with another vehicle

of an equivalent or higher category,

at an impact speed equal to or

greater than 31 mph (50 km/h).

The following cases trigger the pre-

tensioners or Airbags.

In a frontal impact against a rigid

(non-deformable) surface at an im-

pact speed equal to or greater than

16 mph (25 km/h).

9 0 - G e t t i n g t o k n o w y o u r v e h i c l e

ADDITIONAL SAFETY DEVICES

2

The pretensioners or Airbags may

be triggered by:

– an impact underneath the vehicle

(e.g. pavement kerb);

– potholes;

– a drop or hard landing;

– stones;

– ...

The pretensioners or Airbags may

not be triggered by:

– a rear impact, however severe;

– the vehicle overturning;

– side impact at the front or rear of

the vehicle;

– frontal impact, underneath the tail

of a lorry;

– frontal impact against an obsta-

cle with a sharp angle;

– ...

All of the warnings below are given

so that the airbagis not obstructed

in any way when it is inflated and al-

so to prevent the risk of serious in-

juries caused by items which may be

dislodged when it inflates.

G e t t i n g t o k n o w y o u r v e h i c l e - 9 1

ADDITIONAL SAFETY DEVICES

Warnings

2

Warnings in relation to the driver's airbag

– Do not modify the steering wheel or the boss.

– Do not cover the steering wheel boss under any circumstances.

– Do not attach any objects (badge, logo, watch, telephone cradle, etc.) to the steering wheel boss.

– The steering wheel must not be removed (except by qualified personnel from our Network).

– Do not sit too close to the steering wheel: sit with your arms slightly bent (see "Adjusting your driving position"

ꢀ 84). This will allow sufficient space for the airbag to deploy correctly and be fully effective.

Warnings in relation to the passenger airbag

– Fitting seat covers on the front seats is prohibited as this could affect the operation of the passenger airbag.

– Do not attach or glue any objects (badge, logo, clock, telephone holder, etc.) to the dashboard on or near the

airbag.

– Do not place anything between the dashboard and the passenger (animal, umbrella, walking stick, parcels, etc.).

– The passenger must not put his or her feet on the dashboard or seat as there is a risk that serious injuries may be

sustained. As a general rule, parts of the body should be kept away from the dashboard (knees, hands, head, etc.).

9 2 - G e t t i n g t o k n o w y o u r v e h i c l e

ADDITIONAL SAFETY DEVICES

Side seat belt pretensioners

Methods of restraint in addi-

tion to the rear seat belts

– Have the entire re-

straint system checked

following an accident.

2

They consist of:

– Any operation on the entire

system (pretensioners, airbags,

electronic units, wiring) or re-

use on any other vehicle, even

identical, is strictly prohibited.

– To avoid the system trigger-

ing accidentally and causing in-

jury, only qualified personnel

from the brand network may

work on the pretensioners and

airbags.

– The electrical trigger system

may only be tested by a special-

ly trained technician using spe-

cial equipment.

– If the vehicle is scrapped, con-

tact an approved dealer to dis-

pose of the gas generator of the

pretensioners and airbags.

– side seat belt inertia reel preten-

sioners;

– chest force limiters.

These systems are designed to act

independently or together when the

vehicle is subjected to a frontal im-

pact.

Depending on the severity of the im-

pact, the system can cause:

– blocking of the seat belt;

– the seat belt inertia reel preten-

sioner (which engages to correct

seat belt slack).

The pretensioners hold the seat belt

against the body, holding the occu-

pant more securely against the seat,

thus increasing the seat belt's effi-

ciency.

With the ignition on, following a sig-

nificant frontal impact and depend-

ing on the severity of the impact, the

system may trigger the seat belt in-

ertia reel pretensioner 1 which in-

stantly retracts the seat belt.

Load limiter

Above a certain severity of impact,

this mechanism is used to limit the

force of the belt against the body so

that it is at an acceptable level.

Side protection devices

Side airbag

This airbag is fitted to each of the

front seats and is activated at the

door side of the seats to protect the

G e t t i n g t o k n o w y o u r v e h i c l e - 9 3

ADDITIONAL SAFETY DEVICES

occupants in the event of a severe

side impact.

Curtain airbag

2

This airbag fitted in the ceiling along

each side of the vehicle. They inflate

along the front and rear door side

windows to protect the passengers

in the event of a severe side impact.

Central airbag

This airbag fitted to the driver's seat

and deployed between the driver's

seat and the passenger seat in order

to protect the driver and passenger

in the event of a severe side impact.

It also spreads out to protect the dri-

ver, if they are the only one in the

front, in the event of a severe side

impact.

9 4 - G e t t i n g t o k n o w y o u r v e h i c l e

ADDITIONAL SAFETY DEVICES

Warnings

2

Warning relating to the passengerairbag side airbag and theairbag central airbag

Fitting seat covers on the front seats is prohibited as this could hinder the operation of the passenger

–

airbag status.

– Do not place any accessories, objects or even pets between the seatback, the door and the internal fittings. Do not

cover the seatback with objects such as clothes or accessories. This could hinder the operation of theairbag or lead

to injury during inflation.

– Do not drive with the central armrest in the open position as this could hinder the operation of theairbag and/or

lead to injury during inflation.

– Do not place any object(s) on the central armrest compartment cover as this could hinder the operation of

theairbag and/or lead to injury during inflation.

– Do not leave any object(s) protruding from the central armrest compartment as this could hinder the operation of

theairbag and/or lead to injury during inflation.

– No work or modification whatsoever may be carried out on the seat or internal fittings, except by qualified person-

nel from our Network.

– The slits on the front seatbacks (door side and centre console side) correspond to the airbags deployment zone:

never insert any objects into these slits.

G e t t i n g t o k n o w y o u r v e h i c l e - 9 5

ADDITIONAL SAFETY DEVICES

Additional methods of restraint

All of the warnings below are given so that the airbagis not obstructed in any way when it is inflated and also to prevent

the risk of serious injuries caused by items which may be dislodged when it inflates.

2

The airbag is designed to complement the action of the seat belt. Both the airbag and the seat belt are inte-

gral parts of the same protection system. It is therefore essential to wear seat belts at all times. If seat belts

are not worn, the occupants are exposed to the risk of serious injury in the event of an accident. It may also

increase the risk of minor superficial injuries occurring when the airbag is deployed, although such minor in-

juries are always possible with airbags.

If the vehicle should overturn or suffer a rear impact, however severe, the pretensioners and airbags are not always

triggered. Shocks to the underbody of the vehicle, from pavements, potholes, stones etc. can all trigger these sys-

tems.

– Any work or modification on any part of the airbag (airbags, pretensioners, computer, wiring harness, etc.) is strict-

ly prohibited (except by qualified personnel from the network).

– To ensure that the system is in good working order and to avoid accidental triggering of the system which may

cause injury, only qualified personnel from the network may work on an airbag system.

– As a safety precaution, have the airbag system checked if your vehicle has been involved in an accident, or is

stolen or broken into.

– When selling or lending the vehicle, inform the new purchaser of these conditions when handing over this vehicle

user manual.

– When scrapping your vehicle, contact your approved dealer for disposal of the gas generator(s).

9 6 - G e t t i n g t o k n o w y o u r v e h i c l e

CHILD SAFETY

A collision at 31 mph (50

km/ꢀh) is the same as

Driver's responsibility

when parking or stop-

ping the vehicle

General information

Carrying children

falling a distance of 10

2

metres.

Never leave an animal,

Please ensure that you comply with

the legislation of your country.

Children, and adults, must be cor-

rectly seated and strapped in for all

journeys. The children being carried

in your vehicle are your responsibili-

ty.

A child is not a miniature adult. Chil-

dren are at risk of specific injuries as

their muscles and bones have not

yet finished growing. The seat belt

alone would not provide suitable

protection. Use an approved child

seat and ensure you use it correctly.

Transporting a child without a

restraint is the equivalent of al-

lowing him or her to play on a

fourth-floor balcony without

railings.

child or adult who is not self-suf-

ficient alone in your vehicle,

even for a short time.

They may pose a risk to them-

selves or to others by starting

the engine, activating equip-

ment such as the electric win-

dows or by locking the doors.

Also, in hot and/or sunny weath-

er, please remember that the

temperature inside the passen-

ger compartment increases

very quickly.

Never travel with a child held in

your arms.

In the event of an accident, you

will not be able to keep hold of

the child, even if you yourself

are wearing a seat belt.

If your vehicle has been in-

volved in a road accident, re-

place the child seat and have

the seat belts and ISOFIX an-

chorage points checked.

RISK OF DEATH OR SERIOUS IN-

JURY.

To prevent the doors

being opened, use the

"Child lock" feature

ꢀ 64.

Using a child seat

The level of protection offered by

the child seat depends on its ability

to restrain your child and on its in-

stallation. Incorrect installation

compromises the protection it offers

the child in the event of harsh brak-

ing or an impact.

Before purchasing a child seat,

check that it complies with the regu-

G e t t i n g t o k n o w y o u r v e h i c l e - 9 7

CHILD SAFETY

lations for the country you are in and

that it can be fitted in your vehicle.

Consult an approved Dealer to find

out which seats are recommended

for your vehicle.

Set a good example by al-

ways fastening your seat

belt and teaching your

Never leave a child un-

attended in the vehicle.

Check that your child is

2

child:

always strapped in and

The regulations on transporting chil-

dren are specific to each country.

The use of a child seat during trans-

port depends on the age and/or the

size and/or weight of the child.

For children who do not need to be

transported in a child seat, make

sure that the seat belt is correctly

adjusted and fastened.

In all cases, you must comply with

the regulations of the particular

country you are in.

Before fitting a child seat, read the

manual and respect its instructions.

If you experience any difficulties

during installation, contact the man-

ufacturer of the equipment. Keep

the instructions with the seat.

that the belt or safety harness

used is correctly set and adjust-

ed. Avoid wearing bulky cloth-

ing which could cause the belts

to slacken ꢀ 84.

Never let your child put their

head or arms out of the window.

Check that the child is in the

correct position for the entire

journey, especially if asleep.

– to strap themselves in cor-

rectly;

– to always get in and out of the

car at the kerb, away from busy

traffic.

Do not use a second-hand child

seat or one without an instruc-

tion manual.

Check that there are no objects

in the vicinity of the child seat

which could impede its opera-

tion.

Before installing a child

seat on one of the rear

seats, ensure that the

"Easy Access Seat"

function is deactivated for the

driver's and/or front passenger

seat(s) ꢀ 79.

RISK OF INJURY.

9 8 - G e t t i n g t o k n o w y o u r v e h i c l e

CHILD SAFETY

Forward-facing child seats

Booster cushions

Choosing a child seat

Rear-facing child seats

2

Up to 18 kg or 4 years, the child may

travel on a forward-facing seat.

Choose your seat according the

child's size: their head and abdomen

are the areas which must be most

protected. A forward-facing child

seat which is firmly attached to the

vehicle will reduce the risk of impact

to the head. Ensure your child travels

in a forward-facing seat with a har-

ness for as long as their size permits.

From 15 kg or 4 years, the child can

travel using a booster seat, which

will enable the seat belt to be adapt-

ed to suit his size and shape. The

booster seat cushion must be fitted

with guides to position the seat belt

on the child’s thighs rather than the

stomach. It is recommended that

you use a seatback which can be ad-

justed in terms of height to position

the seat belt in the centre of the

shoulder. It must never rest on the

neck or on the arm.

A baby’s head is, proportionally,

heavier than that of an adult and its

neck is very fragile. Transport the

child in this position as long as possi-

ble (until the age of 2 at the very

least). It supports both the head and

the neck.

Choose a bucket type seat for best

side protection and change it as

soon as the child’s head is higher

than the shell.

Choose a bucket type seat for opti-

mum side protection.w

Choose a bucket type seat for opti-

mum side protection.w

G e t t i n g t o k n o w y o u r v e h i c l e - 9 9

CHILD SAFETY

rent regulations if any of the four

cases below applies:

– Universal ISOFIX 3-point forward-

facing seat;

Choosing a child seat mount-

ing

There are two ways to attach child

seats: using the seat belt or using

the ISOFIX system.

Do not use the child

seat if it risks unfasten-

ing the seat belt re-

2

– Semi-universal ISOFIX 2-point seat;

– vehicle-specific;

straining it: the base of

the seat must not rest on the

buckle and/or catch of the seat

belt.

–

i-Size which has either:

Attachment via the seat belt

– a strap which attaches to the

third ring of the seat concerned;

– or a strut that rests on the vehi-

cle floor, compatible with the ap-

proved seat i-Size, the role of

which is to prevent the child seat

from moving in the event of a colli-

sion.

In the latter three cases check that

your child seat can be installed by

consulting the list of compatible ve-

hicles.

The seat belt must be adjusted in or-

der to ensure it works in the event of

sudden braking or impact.

Ensure that the strap paths indicat-

ed by the child seat manufacturer

are observed.

Always check that the seat belt is

correctly fastened by pulling it up,

then pulling it out fully whilst press-

ing on the child seat.

Check that the seat is correctly held

by moving it from side to side and

back to front: the seat should remain

firmly fixed.

The seat belt must nev-

er be twisted or the

tension relieved.

Never pass the shoul-

der strap under the arm or be-

hind the back.

Check that the seat belt has not

been damaged by sharp edges.

If the seat belt does not operate

normally, it will not protect the

child.

Consult an approved Dealer.

Do not use this seat until the

seat belt has been repaired.

No modifications must

be made to the compo-

nent parts of the origi-

Check that the child seat has not

been installed at an angle and that it

is not resting against a window.

nally fitted restraint

system (seat belts, ISOFIX, seats

and their mountings).

Attachment using the ISOFIX

system

Attach the child seat with the ISOFIX

locks, if these are provided. The

ISOFIX system allows quick, easy

and safe fitting.

Authorised child seats ISOFIX are

approved in accordance with cur-

1 0 0 - G e t t i n g t o k n o w y o u r v e h i c l e

CHILD SAFETY

The ISOFIX system consists of two

rings and, in some cases, a third ring.

2

The ISOFIX anchorage

points have been ex-

clusively designed for

child seats with the

ISOFIX system.

Never fit a different type of

child seat, seat belt or other ob-

jects to these fittings.

Check that nothing is obstruct-

ing the anchorage points.

If your vehicle has been in-

volved in a road accident, have

the ISOFIX anchorage points

checked and replace your child

seat.

The third ring 4 is used to attach the

upper strap on some child seats. 2

on some child seats.

The two rings 1 are located between

the seatback and the seat base and

are identified by a

mark.

Rear seats

The upper strap 2 should be posi-

tioned between the seatback and

the rear parcel shelf. To do so, re-

move the rear parcel shelf ꢀ 69.

Before using an ISOFIX

child seat that you pur-

Attach the hook 3 to one of the rings

chased for another ve-

hicle, check that its in-

stallation is authorised. Consult

the list of vehicles which can be

fitted with the seat with the

equipment manufacturer.

4 marked by the

symbol.

Front passenger seat

G e t t i n g t o k n o w y o u r v e h i c l e - 1 0 1

CHILD SAFETY

The ISOFIX anchorage

points have been ex-

clusively designed for

The child seat strap

must be attached to

the corresponding ring.

2

child seats with the

ISOFIX system. Never fit a differ-

ent type of child seat, seat belt

or other objects to these fit-

tings.

Check that nothing is obstruct-

ing the anchorage points.

If your vehicle has been in-

volved in a road accident, have

the ISOFIX anchorage points

checked and replace your child

seat.

Attach the hook 3 of the upper strap

2 to the ring 4 identified by the

symbol.

All seats

Check that the seat-

back of the forward-

facing child seat is in

Pull the upper strap 2 so that the

back of the child seat comes into

contact with the back of the vehicle

seat.

contact with the seat-

back of the vehicle seat. In this

case, the child seat may not al-

ways rest on the seat base of

the vehicle seat.

1 0 2 - G e t t i n g t o k n o w y o u r v e h i c l e

CHILD SEATS

The types of child seats indicated

may not be available. Before using a

different child seat, check with the

manufacturer that it can be fitted.

move it to the furthest forward posi-

tion.

Do not change other settings after

installing the child seat.

Fitting a child seat, general in-

formation

Some seats are not suitable for fit-

ting child seats. The installation ta-

ble and diagram indicate where to

attach a child seat ꢀ 103.

2

In the front seat

RISK OF DEATH OR SE-

RIOUS INJURY: before

fitting a rear-facing

The laws concerning children travel-

ling in the front passenger seat dif-

fer in every country. Consult the cur-

rent legislation and follow the indi-

cations in the installation table and

diagram ꢀ 103.

Before fitting a child seat in this seat

(if authorised):

– lower the seat belt as far as possi-

ble;

– move the seat as far back as pos-

sible;

– gently tilt the seatback away from

the vertical position (approximately

25°);

– on equipped vehicles, raise the

seat base as far as possible.

Always fully raise the seat headrest

so that it does not interfere with the

child seat ꢀ 75.

child seat on the front

Fit the child seat in a

rear seat wherever

possible.

passenger seat, check that the

airbag has been deactivated:

Make sure the child

– Before installing the seat in

vehicles equipped with an

airbag ꢀ 119 deactivation/acti-

vation lock;

– After installing the seat in ve-

hicles equipped with the

passenger detection system

ꢀ 121.

seat or the child's feet do not

prevent the front seat from

locking correctly ꢀ 75.

Check that when installing the

child seat in the vehicle it is not

at risk of coming loose from its

base.

If you have to remove the head-

rest, check that it is correctly

stored so that it does not come

loose under harsh braking or im-

pact.

Always attach the child seat to

the vehicle even if it is not in use

so that it does not come loose

under harsh braking or impact.

In the rear side seat

A carrycot can be installed across

the vehicle and will take up at least

two seats. Position the child with his

or her feet nearest the door.

Before installing a rear-facing child

seat, move the front seat forwards

as far as possible then, once the

child seat is installed, move the front

After installing the child seat, when

this is possible, you can move the ve-

hicle seat forward if necessary (so

as to leave enough space in the rear

seats for passengers or other child

seats). For a rear-facing child seat,

do not let it touch the dashboard or

G e t t i n g t o k n o w y o u r v e h i c l e - 1 0 3

CHILD SEATS

seat backwards as far as possible

without it touching the child seat.

For the safety of the child in the for-

ward-facing position:

– move the seat in which the child

will be seated as far back as possi-

ble;

– Move the seat in front of the child

forwards, and set the position of the

seatback to avoid contact between

the seat and the child's legs.

child seat is positioned ꢀ 82. If nec-

essary, position the rear seat as far

back as possible. This must be done

before fitting the child seat. Check

that the child seat is resting against

the seatback of the rear seat.

Fit the child seat in a

rear seat wherever

possible.

2

To install a seat ISOFIX

in the rear left-hand seat, unfas-

ten the central seatbelt by hand

before engaging the locks.

Installing a booster

seat (group 2 or 3)

Check that the seat

belt ꢀ 84 operates

(winds) correctly.

In rear centre seat

Check that the belt is suitable for se-

curing your child seat. Consult an

approved Dealer.

Make sure the child

seat or the child's feet

do not prevent the

Adjust the seat belt by position-

ing:

– the shoulder strap on the

child's shoulder without it

touching their neck;

– the lap belt so that it lies flat

on the thighs and against the

pelvis.

front seat from locking

correctly ꢀ 75.

A child seat with a floor

support must never be

installed on the rear

centre seat.

RISK OF DEATH OR SERIOUS IN-

JURY.

Before installing a child

seat on one of the rear

seats, ensure that the

"Easy Access Seat"

If necessary, adjust the position

of the vehicle seat.

function is deactivated for the

driver's and/or front passenger

seat(s) ꢀ 79.

RISK OF INJURY.

In all situations, remove the head-

rest of the rear seat on which the

1 0 4 - G e t t i n g t o k n o w y o u r v e h i c l e

2

G e t t i n g t o k n o w y o u r v e h i c l e - 1 0 5

CHILD SEATS

Attachment by seat belt

Fitting diagram

2

1 0 6 - G e t t i n g t o k n o w y o u r v e h i c l e

CHILD SEATS

RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child seat on the front passenger seat,

check that the airbag has been deactivated:

2

– Before installing the seat in a vehicle equipped with an airbag ꢀ 119 deactivation/activation lock;

– After installing the seat in vehicles equipped with the passenger detection system ꢀ 121.

Check the status of the airbag before fitting a child seat or allowing a passenger to use the seat.

Seat not suitable for fitting child seats.

Child seat attached using the belt

Seat equipped for attaching a "universal" approved seat using a seatbelt.

Seat enabling a child seat with "B2" approval to be attached by seat belt.

Using a child safety system which is not approved for this vehicle will not properly protect the baby or child.

They risk serious or even fatal injury.

Check that your child is always strapped in and that the belt or safety harness used is correctly set and ad-

justed.

If necessary, adjust the seat position accordingly.

G e t t i n g t o k n o w y o u r v e h i c l e - 1 0 7

CHILD SEATS

Do not fit a child seat while the central seatback is folded down.

2

1 0 8 - G e t t i n g t o k n o w y o u r v e h i c l e

2

G e t t i n g t o k n o w y o u r v e h i c l e - 1 0 9

CHILD SEATS

Installation table

The table below summarises the information shown on the installation diagram in order to ensure the regulations in

force are respected.

2

Front passenger seat (8)

Weight of the

child

Rear side seats

(8)

Rear centre

seat (8)

Type of child seat

With airbag de- With airbag ac-

activated

tivated

Carrycot fitted across the

vehicle

< 10 kg

X

U (2)

Group 0

Rear-facing shell seat

Groups 0 or 0 +

< 10 kg and < 13

kg

U (1) (5)

X

U (3)

U (3) (7)

U (4) (7)

U (4)

Shell seat/rear-facing seat

Groups 0+ and 1

< to 13 kg and 9

to 18 kg

U (1) (5)

Forward-facing seat

Group 1

9 to 18 kg

X

U (5) (6)

U / B2 (5) (6)

U (4)

Booster seat

Groups 2 and 3

15 to 25 kg and

22 to 36 kg

U / B2 (4)

(1) RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child seat on the front passenger seat,

check that the airbag has been deactivated:

– Before installing the seat in a vehicle equipped with an airbag ꢀ 119 deactivation/activation lock;

– After installing the seat in vehicles equipped with the passenger detection system ꢀ 121.

X = Seat not suitable for fitting child seats of this type.

1 1 0 - G e t t i n g t o k n o w y o u r v e h i c l e

CHILD SEATS

U = Seat enabling a child seat with "Universal" approval to be attached by seat belt: check that it can be fitted.

B2 = Boosters in groups 2 and 3 (15 to 25 kg and 22 to 36 kg).

(2) A carrycot can be fitted across the vehicle and it will take up at least two seats. Position the child with his or her feet

2

nearest the door.

(3) Before installing a rear-facing child seat, move the front seat forwards as far as possible then, once the child seat is

installed, move the front seat backwards as far as possible without it touching the child seat.

(4) In all situations, remove the headrest of the rear seat on which the child seat is positioned. This must be done before

fitting the child seat. Move the seat in front of the child forwards, move the seatback forward to avoid contact between

the seat and the child's legs.

(5) Raise the seat to the maximum and position it as far back as possible, tilting the seatback slightly (approximately 25°).

(6) The airbag can be activated or deactivated, in both cases safety is guaranteed.

(7) RISK OF DEATH OR SERIOUS INJURY: a child seat with a floor support must never be fitted.

(8) Deactivate the "Easy Access Seat" function before installing a child seat on the front passenger seat

and/or on the rear seats ꢀ 79.

Risk of injury.

G e t t i n g t o k n o w y o u r v e h i c l e - 1 1 1

CHILD SEATS

Attachment using the ISOFIX system

Fitting diagram

2

1 1 2 - G e t t i n g t o k n o w y o u r v e h i c l e

CHILD SEATS

For the front passenger seat, the use of a child seat with a floor support is recommended to avoid triggering

the seat belt warning signal.

2

Using a child safety system which is not approved for this vehicle will not properly protect the baby or child.

They risk serious or even fatal injury.

Fitting a seat ISOFIX in the rear-left seat means the middle seat cannot be used. The central seat belt will no

longer be either accessible or useable.

RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child seat on the front passenger seat,

check that the airbag has been deactivated:

– Before installing the seat in a vehicle equipped with an airbag ꢀ 119 deactivation/activation lock;

– After installing the seat in vehicles equipped with the passenger detection system ꢀ 121.

Seat which does not allow a child seat to be fitted.

Child seat attached using theISOFIX system

Seat equipped for attaching a ISOFIX or i-Size child seat.

The front and rear seats are equipped with an anchorage point allowing an ISOFIX universal forward-facing child

seat to be attached. The anchoring points are located on the passenger seatback for the front seat and on the bench

seatback for the rear seats.

G e t t i n g t o k n o w y o u r v e h i c l e - 1 1 3

CHILD SEATS

Check that your child is always strapped in and that the belt or safety harness used is correctly set and ad-

justed.

If necessary, adjust the seat position accordingly.

2

Do not fit a child seat while the central seatback is folded down.

Fit the child seat in a rear seat wherever possible.

To install an ISOFIX seat in this seat, unbuckle the seat belt by hand before engaging the bolts.

1 1 4 - G e t t i n g t o k n o w y o u r v e h i c l e

2

G e t t i n g t o k n o w y o u r v e h i c l e - 1 1 5

CHILD SEATS

Installation table

The table below summarises the information shown on the installation diagram in order to ensure the regulations in

force are respected.

2

Front passenger seat (8)

Weight of the Size of seat

Rear side

seats (8)

Rear centre

seat (8)

Type of child seat

With airbag

deactivated

With airbag

activated

child

[fixture]

Carrycot fitted across

the vehicle

Group 0

L1 [F]

L2 [G]

< 10 kg

< 13 kg

X

IL (2)

X

Rear-facing shell seat

Groups 0 or 0 +

R1 [E]

IL (1) (3)

X

IL (4)

X

Rear-facing seat

Groups 0+ and 1

R3 [C]

R2 [D]

< to 13 kg and

9 to 18 kg

F3 [A]

F2 [B]

F2X [B1]

Forward-facing seat

Group 1

IUF - IL

(3) (7)

IUF - IL

(5)

9 to 18 kg

X

15 to 25 kg

and 22 to 36

kg

Booster seat

Groups 2 and 3

IUF - IL

(3) (7)

IUF - IL

(5)

B2

Rear-facing seat

i - U (1) (3)

X

i - U (4)

i - U (5)

X

Seati-Size

Forward-facing seat

Booster seat

X

i - UF (3) (7)

i - UF (6) (7)

X = Seat not suitable for fitting child seats.

1 1 6 - G e t t i n g t o k n o w y o u r v e h i c l e

CHILD SEATS

IUF = Seat allowing a child seat with "Universal or vehicle-specific" approval to be attached using the ISOFIX system on

equipped vehicles: check that it can be fitted.

IL = Seat allowing a child seat with "Semi-universal or vehicle-specific" approval to be attached using the ISOFIX system

on equipped vehicles: check that it can be fitted.

i-U = Suitable for "Universal" front-facing and rear-facing i-Size restraint devices.

i-UF = Suitable only for "universal" front-facing and rear-facing i-Size restraint devices.

2

(1) RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child seat on the front passenger seat,

check that the airbag has been deactivated:

– Before installing the seat in a vehicle equipped with an airbag ꢀ 119 deactivation/activation lock;

– After installing the seat in vehicles equipped with the passenger detection system ꢀ 121.

(2) A carrycot can be fitted across the vehicle and it will take up at least two seats. Position the child with his or her feet

nearest the door.

(3) Move the vehicle seat backwards as far as possible and lower it as much as possible, then tilt the seatback slightly (by

approximately 25°).

(4) Before installing a rear-facing child seat, move the front seat forwards as far as possible then, once the child seat is

installed, move the front seat backwards as far as possible without it touching the child seat.

(5) In all situations, remove the headrest of the rear seat on which the child seat is positioned. This must be done before

fitting the child seat. Move the seat in front of the child forwards, move the seatback forward to avoid contact between

the seat and the child's legs.

(6)Raise the seat to the maximum and position it as far back as possible, tilting the seatback slightly (approximately 25°).

The size of the ISOFIX child seat is indicated by a letter:

– F3, F2, F2X [A, B, B1]: for forward-facing child seats in Group 1 (9 to 18 kg);

– B2: boosters in groups 2 and 3 (15 to 25 kg and 22 to 36 kg);

– R3, R2 [C, D]: rear-facing seats or shell seats in group 0+ (less than 13 kg) or group 1 (9 to 18 kg);

– R1 [E]: rear-facing shell seats in group 0 (less than 10 kg) or 0+ (less than 13 kg);

– L1,L2 [F, G]: carrycots in group 0 (less than 10 kg).

(7) The airbag can be activated or deactivated, in both cases safety is guaranteed.

G e t t i n g t o k n o w y o u r v e h i c l e - 1 1 7

CHILD SEATS

(8) Deactivate the "Easy Access Seat" function before installing a child seat on the front passenger seat

and/or on the rear seats ꢀ 79.

Risk of injury.

2

1 1 8 - G e t t i n g t o k n o w y o u r v e h i c l e

CHILD SAFETY: DEACTIVATING, ACTIVATING THE FRONT PASSENGER AIRBAG

Before installing a child seat on the

front passenger seat:

– check that the child seat can be in-

stalled on this seat;

– it is essential to deactivate the

airbagfor a rear-facing child seat.

When the ignition is switched on, you

Child safety: deactivating, ac-

tivating the front passenger

airbag

must check that the warning

light is illuminated on the display 2 .

This light remains continuously lit to

let you know that you can fit a child

seat.

2

Warning

For vehicles not equipped

with a lock 1 ꢀ 121.

The passenger airbag

may only be deactivat-

ed or activated while

DANGER

Since operation of the

front passenger airbag

is not compatible with

the vehicle is station-

ary with the ignition off.

the position of a rear-facing

child seat, NEVER fit a rear-fac-

ing child restraint system in a

seat protected by an ACTIVAT-

ED front AIRBAG. This could

lead to the CHILD'S DEATH or

SERIOUS INJURY.

Front passenger airbag deacti-

vation

To deactivate the airbag: with the

vehicle stationary and the ignition

switched off, push and turn the lock

1 to the OFF position.

(depending on the vehicle)

G e t t i n g t o k n o w y o u r v e h i c l e - 1 1 9

CHILD SAFETY: DEACTIVATING, ACTIVATING THE FRONT PASSENGER AIRBAG

label above) are provided to remind

you of these instructions.

Activation of the front passen-

ger airbag

2

To reactivate the airbag: with the

vehicle stationary and the ignition

off, push and turn the lock 1 to the

ON position.

When the ignition is switched on, you

(depending on the vehicle)

must check that the

warning

You should reactivate the airbag as

soon as you remove the child seat

from the front passenger seat to en-

sure the protection of the front pas-

senger in the event of an impact.

light is off and that the

warn-

ing light lights up on the display 2 af-

ter each start-up for around 1

minute.

The front passenger airbag is acti-

vated.

Operating faults

The markings on the dashboard and

the labels A on each side of the pas-

senger sun visor 3 (see example of

In the event of a fault with the front

passenger airbag activation/deacti-

1 2 0 - G e t t i n g t o k n o w y o u r v e h i c l e

CHILD SAFETY: DEACTIVATING, ACTIVATING THE FRONT PASSENGER AIRBAG

the different types of seats ꢀ 99 and

vation system, the

and

–

warning light 2 on, the pas-

the methods for installing them ꢀ

119.

senger airbag is activated. In this

case, the warning light stays on for

approximately 65 seconds.

After the initialisation phase, if the

system detects a change of status

(e.g. passenger seat occupied when

the ignition is switched on, then not

occupied), the following messages

are displayed on the instrument

panel:

warning lights are dis-

played on the instrument panel.

Switch off the ignition and check the

position of the lock 1 .

Switch the ignition on again: the

warning lights go out.

If the problem persists, it signals a

system failure. In this case, it is pro-

hibited for a rear-facing child seat to

be fitted to the front passenger seat

or for any other passenger to occu-

py the seat.

To find out the type of child seat au-

thorised for use on the front passen-

ger seat ꢀ 103.

2

– "Passenger airbag activated", ac-

companied by the

light;

or

warning

Contact your approved Dealer as

soon as possible;

– "Passenger airbag deactivated",

Passenger detection system

Operation

accompanied by the

light.

warning

Operation

Depending on the vehicle, the pas-

senger detection system automati-

cally manages the activation and

deactivation of the passenger

airbag according to whether the

front passenger seat is occupied.

After an initialisation phase of ap-

proximately 5 seconds, the warning

lights 1 and 2 let you check the acti-

vation status of the passenger

airbag:

DANGER

After fitting a rear-fac-

ing child seat, check

that the airbag is dis-

abled (warning light 1 on).

The passenger airbag is automati-

cally disabled if a child seat is fitted

in the front passenger seat or if the

seat is not occupied.

Before fitting a child seat on the

front passenger seat, find out about

–

warning light 1 on, the pas-

senger airbag is disabled. In this

case, the warning light stays on con-

tinuously;

G e t t i n g t o k n o w y o u r v e h i c l e - 1 2 1

CHILD SAFETY: DEACTIVATING, ACTIVATING THE FRONT PASSENGER AIRBAG

Never switch off the ig-

nition before the vehi-

cle has stopped com-

pletely. Once the en-

2

gine has stopped, the brake ser-

vo, power-assisted steering,

etc., and the passive safety de-

vices such as the airbags and

pretensioners will no longer op-

erate.

If the

deactivation warning

light is on while an adult passenger

is seated in the front passenger

seat, it may not be correctly fitted.

The markings on the dashboard and

the labels A on each side of the pas-

senger sun visor 3 (such as the label

above) remind you that you must not

place a child in a rear-facing seat

when the passenger airbag is acti-

vated.

If the

activation warning light

is on when a rear-facing child seat is

fitted:

– switch off the ignition;

– remove the child seat from the

passenger seat;

Perform the following actions to al-

low the system to detect the pas-

senger:

– remove any additional elements

from the seat base, such as beach

towels, seat covers, etc.;

– make sure that the seatback is not

tilted backwards too much;

– have the passenger sit straight on

the seat, centred on the seat cush-

ion with their legs comfortably ex-

tended;

– remove any additional elements

that may be located between the

child seat and the passenger seat;

– refit the child seat according to

the instructions of the child seat

manufacturer;

– start the vehicle.

If the problem persists, position the

child seat at the rear and contact an

approved dealer.

– leave the passenger seated in this

position for two to three minutes af-

1 2 2 - G e t t i n g t o k n o w y o u r v e h i c l e

CHILD SAFETY: DEACTIVATING, ACTIVATING THE FRONT PASSENGER AIRBAG

ter the activation warning light

comes on.

Warning relating to the

passenger airbag : fit-

ting seat covers on the

front seats is prohibit-

If the problem persists, have the

passenger sit in the rear and con-

tact an approved dealer.

2

ed.

DANGER

After fitting a rear-fac-

ing child seat, check

that the airbag is dis-

abled (warning light 1 on).

A wet seat may affect the effective-

ness of the passenger detection sys-

tem. If the front passenger seat is

wet, dry it immediately.

Additional factors affecting the

operation of the system

Seat belts help keeping the passen-

ger in position on the seat during ve-

hicle manoeuvring and braking. This

helps the passenger detection sys-

tem to maintain the passen-

gerairbag status.

A thick layer of additional material

(thick coat, cushion, large object

placed in the passenger's rear pock-

et, heating or massage device) may

hinder the correct operation of the

passenger detection system.

Note: placing an object on the pas-

senger seat base may activate the

warning light in some cases.

G e t t i n g t o k n o w y o u r v e h i c l e - 1 2 3

DRIVING POSITION

Driving position: left-hand dri-

ve

2

1 2 4 - G e t t i n g t o k n o w y o u r v e h i c l e

DRIVING POSITION

15. Cup holder.

The fittings described below DE-

PEND ON THE VEHICLE VERSION

AND COUNTRY.

1. Side air vents.

2. Stalk for:

– direction indicator lights;

– exterior lights;

– rear fog lights.

27. Controls for:

16. USB-C ports in the centre con-

sole.

– lighting dimmer for control instru-

ments;

2

– the "My Safety" function

17. "Hands-free" card holder.

– luggage compartment opening

18. Induction charging zone or cen-

tre console storage compartment.

control;

– ...

19. Engine start/stop button.

20. Radio remote control.

21. Control MULTI-SENSE.

22. Controls for:

– trip computer information read-

out and vehicle settings customisa-

tion menu;

3. Instrument panel.

4. Driver airbag and horn location.

5. Electronic selector lever.

6. Steering column stalk for wind-

screen and rear screen washer/

wiper.

– remote radio and navigation sys-

tem.

7. Centre air vents.

8. Demister outlet.

9. Multimedia screen.

10. Passenger airbag location.

11. Fuse box.

23. Control for adjusting steering

wheel height and reach.

24. Main switch and controls for the

speed limiter/adaptive cruise con-

trol Stop and Go and Active Driver

Assist functions.

12. Glovebox

25. Bonnet release control.

26. Controls for:

13. Controls for:

– heating or air conditioning;

– hazard warning lights;

– door central locking;

– ...

– activating/deactivating the elec-

tronic parking brake;

– activating/deactivating the

Autohold function;

– ...

14. Accessories socket.

G e t t i n g t o k n o w y o u r v e h i c l e - 1 2 5

DRIVING POSITION

Driver’s position, right-hand

drive

2

1 2 6 - G e t t i n g t o k n o w y o u r v e h i c l e

DRIVING POSITION

– activating/deactivating the elec-

tronic parking brake;

– activating/deactivating the

AUTOHOLD function;

– ...

22. Cup holder.

The fittings described below DE-

PEND ON THE VEHICLE VERSION

AND COUNTRY.

23. USB-C ports in the centre con-

sole.

2

1. Side air vents.

24. "Hands-free" card holder.

2. Location of the airbag

passenger.

25. Induction charging zone or cen-

tre console storage compartment.

13. Bonnet release control.

14. Radio remote control.

15. MULTI-SENSE control.

16. Controls for:

– trip computer information read-

out and vehicle settings customisa-

tion menu;

3. Centre air vents.

4. Multimedia screen.

5. Demister outlets.

6. Stalk for:

– direction indicator lights;

– exterior lights;

– rear fog lights.

26. Glovebox

27. Fuse box.

– remote radio and navigation sys-

tem.

7. Instrument panel.

17. Main switch and controls for the

speed limiter/adaptive cruise con-

trol Stop and Go Active Driver Assist

functions.

8. Driver airbag and horn location.

9. Electronic selector lever.

10. Steering column stalk for wind-

screen and rear screen wash/wiper.

18. Control for adjusting steering

wheel height and reach.

11. Controls for:

– lighting dimmer for control instru-

19. Engine start/stop button.

20. Controls for:

– heating or air conditioning;

– hazard warning lights;

– door central locking;

– ...

ments;

– the "My Safety" function

– luggage compartment opening

control;

– ...

12. Controls for:

21. Accessories socket.

G e t t i n g t o k n o w y o u r v e h i c l e - 1 2 7

TRIP COMPUTER

Repeatedly press upwards/down-

wards on the switch 1 to browse be-

tween these functions.

From the instrument panel A :

a) trip settings:

from the energy consumed on the

electric counter.

General information

Interpreting some of the values

displayed after resetting

Trip computer and warning sys-

tem A

2

The values showing average energy

consumption and range will become

more stable and reliable the further

you have travelled since the last

time the Reset button was pressed.

For the first few miles after pressing

the reset key you will notice that the

range increases as you travel. This is

because the average energy con-

sumption since the last reset is tak-

en into account. However, the aver-

age energy consumption may fall

when:

– average energy consumption

since the last reset and current ener-

gy consumption;

– distance travelled since last reset.

b) reset the pressure of the tyres;

c) service interval;

d) trip log, operating faults and infor-

mation messages.

Resetting the journey parame-

ters (reset button)

With one of the trip parameters se-

lected as the display, press and hold

the switch 1 downwards until the

display resets to zero.

– the vehicle stops accelerating;

– when driving from an urban area

onto the open road.

Depending on the vehicle, this in-

cludes the following functions:

– mileage;

– trip settings;

Automatic resetting of the jour-

ney parameters

Some on-board computer

information appears on

the navigation system

display.

The trip settings mileage

recorder is reset simultaneously

in the on-board computer and

the navigation system.

Resetting occurs automatically

when the maximum value of any of

the parameters is exceeded.

– information messages;

– operating fault messages (associ-

ated with the

warning light);

– warning messages (connected to

Reading energy consumption

values

the warning light).

Some vehicle equipment items con-

sume energy: the energy consumed

by the vehicle may therefore differ

All these functions are detailed in

the vehicle user manual.

1 2 8 - G e t t i n g t o k n o w y o u r v e h i c l e

TRIP COMPUTER

Resetting the estimated range

After the traction battery has been

fully recharged, you can select two

types of resetting: manual or auto-

matic.

2

Manual reset

Select the trip setting to reset, then

press and hold the switch 1 to reset

the range.

Automatic reset

The range is automatically reset

when the traction battery is fully

charged. The calculated value corre-

sponds to an average use, taking in-

to account the exterior temperature.

If a particularly economical driving

pattern is identified, the calculation

is corrected and the range is in-

creased.

G e t t i n g t o k n o w y o u r v e h i c l e - 1 2 9

TRIP COMPUTER

Journey settings

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY

2

Examples of selections

Interpreting the display selected

a) Trip settings.

Current energy consumption.

+ 13,4

kWh

Average energy consumption.

The value is displayed after having travelled at least 400 metres since the

last reset.

12,8

kWh/100 km

Journey

1284,7

km

Distance travelled since last reset.

b) Reset the pressure of the tyres

ꢀ 189

Tyre pressure init. long press

Examples of selections

Interpreting the display selected

c) Service interval.

Distance remaining until the next service (displayed in miles or kilometres),

then when the service nears, several scenarios are possible:

– interval less than 932 miles (1,500 km) or one month: the "Service in" mes-

sage is displayed along with the remaining distance or time;

– when a service is due, the "Service due" message is displayed accompa-

nied by the first limit (distance or time);

Service in

1,200 miles (1,936 km)

or 3 months

1 3 0 - G e t t i n g t o k n o w y o u r v e h i c l e

TRIP COMPUTER

Examples of selections

Interpreting the display selected

– range equal to 0 miles (0 km) or date of service reached: the "Service Re-

2

quired" message is displayed accompanied by the

The vehicle requires a service as soon as possible.

warning light.

Resetting the display after the service in accordance with the maintenance schedule.

The service interval must only be reset after a service which complies with the recommendations in the maintenance

schedule.

Special feature: to reset the service interval, press and hold one of the display reset buttons for approximately 10 sec-

onds until the display shows the service range permanently.

Examples of selections

Interpreting the display selected

d) Vehicle settings customisation menu.

ꢀ 139

Settings Press "OK"

e) Trip log.

Successive display:

– information messages;

– operating fault messages.

WARNING: Boot Open

G e t t i n g t o k n o w y o u r v e h i c l e - 1 3 1

TRIP COMPUTER

Information messages

These can help in the vehicle starting phase, or give information about a selection or a driving status.

Examples of information messages are given in the following pages.

2

Examples of messages

Interpreting the display selected

"Disconnect the cable to start"

Indicates that the charging cable is still plugged into the vehicle.

Unplug, then plug in the vehicle.

"Check the connections"

If the message still shows, this may be caused by the external charging con-

ditions or by the home installation.

Indicates a possible electrical fault or a defective charging cable: change

the charging terminal or location or have the cable checked.

"Check the charging terminal"

"Power cut off during charging"

Indicates an electrical fault while charging. Restart charging.

If this does not work, have the electrical installation checked.

1 3 2 - G e t t i n g t o k n o w y o u r v e h i c l e

TRIP COMPUTER

Operating fault messages

They appear with the

warning light to inform you that you should drive very carefully to an approved dealer as

2

soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle.

They disappear when the display selection key is pressed or after several seconds and are stored in the computer log.

The

warning light stays on. Examples of operating fault messages are given in the following pages.

Examples of messages

Interpreting the display selected

« WARNING: Check Airbag »

Indicates a fault in the restraint system in addition to the seat belts. In the

event of an accident, it is possible that they may not be triggered.

« Check vehicle »

Indicates a fault on one of the pedal sensors or in the 12 V battery manage-

ment system.

« WARNING: Check Braking System »

« Check Post-collision »

Indicates wear or the need to check the braking system.

Indicates a problem with the multi-collision braking.

« Check Vehicle charging plug »

Indicates overheating at the vehicle-side charging socket. Wait for approxi-

mately 20 minutes then try again. If this does not work, contact an approved

dealer.

« Check Electric System »

Indicates a fault in the traction system.

« Battery charging impossible »

Indicates a fault on the traction battery recharge system.

G e t t i n g t o k n o w y o u r v e h i c l e - 1 3 3

TRIP COMPUTER

Warning messages

2

These appear with the

conditions allow. Stop your engine and do not restart it. Call an approved Dealer.

warning light and require you to stop immediately, for your own safety, as soon as traffic

Some examples of warning messages are given below. Note: the messages appear on the display either individually or

alternately (when there are several messages to be displayed), and may be accompanied by a warning light and/or a

beep.

Examples of messages

"Braking system fault"

"Steering fault"

Interpreting the display selected

Indicates a fault in the braking system.

Indicates a fault in the steering system.

"Electric engine fault"

"Electrical fault"

Indicates that the vehicle is losing power.

Indicates a fault in the electric system.

"Puncture"

Indicates that at least one tyre is punctured or severely underinflated.

If the vehicle is parked on the hard shoulder, you must warn other road users of your vehicle's presence with

a warning triangle or with other devices as per the legislation applying to the country you are in.

1 3 4 - G e t t i n g t o k n o w y o u r v e h i c l e

TRIP COMPUTER

All of the available views display the

following essential information on

the instrument panel:

Displays and indicators

Instrument panel A

– speedometer;

2

– the information on the activated

driving aids;

– information area.

Only while the vehicle is charging,

the "Charge" view displays the

range, the battery percentage and

the remaining charging time on the

instrument panel.

The "Driving aids" view displays the

essential information on the instru-

ment panel with that of the active

driving aids in full screen.

The "Classic" view displays the es-

sential information on the instru-

ment panel and, depending on the

vehicle, the power meter.

The "Navigation" view displays the

essential information and the road

map duplicated from the multime-

dia system on the entire instrument

panel.

View B displays the essential infor-

mation on the instrument panel,

along with your vehicle and its envi-

ronment (lanes, surrounding vehi-

cles moving in the same direction,

etc.).

Note: the system only recognises ve-

hicles in the car, lorry and motorbike

categories.

lights up when the driver’s door is

opened. In some cases, the appear-

ance of a warning light is accompa-

nied by a message.

Selection of views

The "Minimal" view displays only the

essential information on the instru-

ment panel.

The "Realist" view B

Depending on the vehicle, several

views may be available on the in-

strument panel. To select a view,

press control 1 as many times as

necessary to scroll through the dif-

ferent views on the instrument pan-

el A until you reach the desired view.

G e t t i n g t o k n o w y o u r v e h i c l e - 1 3 5

TRIP COMPUTER

Information on the navigation in

progress 4 .

Information display

Power meter 5 .

2

Total mileage recorder 6 .

Regenerative braking level warning

light 8 .

Battery information 9 (traction bat-

tery charging rate, estimated

range).

Speedometer 2 .

The vehicle speed is limited to ap-

proximately 93 mph (150 km/h) (or

106 mph (170 km/h) depending on the

vehicle).

Excessive speed audible alarm

Depending on the vehicle and coun-

try, the

warning light is dis-

played and a beep sounds. This beep

sounds as soon as the vehicle is trav-

elling at over 75 mph (120 km/h).

This warning light remains lit for as

long as the vehicle is travelling at

over 75 mph (120 km/h).

Information area 7 , browse using

the control 10 to select various wid-

gets on the instrument panel A :

– trip computer information

(mileage recorder, consumption,

etc.);

Information on driving aids 3 .

1 3 6 - G e t t i n g t o k n o w y o u r v e h i c l e

TRIP COMPUTER

– telephone, multimedia (audio

Immobilisation threshold imminent

source currently playing, etc.) infor-

Depending on the vehicle, when the

charge level reaches approximately

4% or 6%, a beep will sound again

and the meter will light up in red or,

depending on the vehicle, 30 sec-

onds after the meter lights up in red.

mation;

– vehicle information (warning mes-

2

sages, etc.);

– ...

Depending on the vehicle, when the

charge level reaches 3.5% or ap-

proximately 5%, the range value is

no longer displayed. Engine perfor-

mance gradually decreases until the

vehicle comes to a halt ꢀ 356.

Estimated range 16

The estimated range in real time is

calculated according to various fac-

tors such as the conditions of use,

equipment, driving style, weather

conditions, etc. The calculation is

based on the last few kilometres dri-

ven. It is automatically corrected

during your journey if the factors

change (type of road, driving style,

etc.).

In addition, to understand your esti-

mated range, you can refer to indi-

cators 17 and 18 . Depending on the

traction battery charging level:

Charging cable "plugged-

in"warning light 11

This comes on when the charging

cable is plugged into the vehicle.

Charge level 12

The gauge indicates the level of en-

ergy remaining.

Remaining charging time 13

Traction battery charge rate 14

Reserve threshold

Depending on the vehicle, if the trac-

tion battery charge reaches approx-

imately 7% or 12%, the gauge and in-

dicator light 15

appear in yel-

low, accompanied by a beep.

To optimise your range ꢀ 187.

G e t t i n g t o k n o w y o u r v e h i c l e - 1 3 7

TRIP COMPUTER

Please refer to the multimedia in-

structions for more information.

Instrument panel in miles

2

To use certain driving aid

functions, it is necessary

to change the unit of

measurement on the instru-

ment panel in order to obtain

the appropriate information

when driving in a country where

the speed units differ from

those set as default on your ve-

hicle.

– indicator light 17 : "high" range es-

timation calculated according to

optimal driving conditions (e.g. dri-

ving on an A-road or dual carriage-

way in warm weather with little use

of air conditioning);

– indicator light 18 : "low" range esti-

mation calculated according to un-

favourable driving conditions (e.g.

driving on a motorway in winter or in

a traffic jam with intensive use of the

heating system).

(option to switch to km/h)

For safety reasons, car-

ry out any adjustments

while the vehicle is sta-

tionary.

With the vehicle stationary and the

engine running, from the multimedia

screen 19 select the "Vehicle" World,

press the "Settings" menu, "Sys-

tem", "Units" then "Speed".

Choose between km/h or mph.

The speedometer and some of the

distance information displayed on

the instrument panel are converted.

To return to the previous mode, re-

peat the same operation.

To optimise your range ꢀ 187.

Note: once the battery is switched

off, the on-board computer auto-

matically returns to the original unit

of measurement.

1 3 8 - G e t t i n g t o k n o w y o u r v e h i c l e

TRIP COMPUTER

minated (e.g. for the "Follow me

home" function).

Please refer to the multimedia in-

structions for further information.

Adjusting the settings

Vehicle settings personalisa-

tion menu

Select a tab then the function to be

modified (the display depends on

the vehicle equipment and country):

2

a) "Access":

– « Auto door lock while driving » ;

– « Hands-free lock/unlock » ;

– « Access and start by phone » ;

– ...

For safety reasons, car-

ry out any adjustments

while the vehicle is sta-

tionary.

b) "Welcome":

– « External lighting sequence » ;

– « Internal sequence sound » ;

– « Automatic mirrors' unfolding » ;

– « Internal light function » ;

– ...

"Favourites" function

c) "Driving lights":

– « Adaptive Vision » ;

– « Driving side selection » ;

– ...

Depending on the vehicle equip-

ment, this function allows you to ac-

tivate/deactivate and adjust some

of the vehicle's functions.

d) "Wiping":

– « Rear wiper when in reverse

Accessing the settings menu

gear » ;

– « Automatic front wiper » ;

– ...

Depending on the function, select:

– "ON" or "OFF" to activate or deac-

tivate;

or

With the vehicle stationary and the

engine on, from the multimedia

screen 1 select the "Vehicle" world,

press the "Vehicle" menu then the

"Exterior" tab to access the various

settings.

Depending on the vehicle, by press-

ing the steering wheel control 2 you

can activate the following functions

according to the stored user set-

– a time period to adjust the time

during which the headlights are illu-

G e t t i n g t o k n o w y o u r v e h i c l e - 1 3 9

TRIP COMPUTER

tings that you have previously de-

fined:

– heated seats;

– heated steering wheel;

– setting selection (access, wel-

come, lighting, wiper, etc.);

– "Hands-free Park Assist" function;

– ECO mode;

Please refer to the multimedia in-

structions for further information.

Clock and outdoor tempera-

ture

Exterior temperature indicator

Setting the time

2

Special feature:

When the outside temperature is be-

tween -3°C and +3°C, the °C figures

flash (this indicates a risk of ice for-

mation).

– 360° camera;

– ...

For more information on program-

ming this function, please refer to

the multimedia instructions.

If the power supply is cut

(battery disconnected,

supply wire cut, etc.), the

clock must be reset.

We recommend that you do not

adjust these settings while dri-

ving.

For safety reasons, car-

ry out any adjustments

while the vehicle is sta-

tionary.

The time and exterior temperature

are displayed on the multimedia

screen 1 .

To set the time, from the multimedia

screen 1 select the "Vehicle" world,

press the "Settings" menu then

"Date and time".

Exterior temperature

indicator

As ice formation is re-

lated to climatic expo-

sure, local air humidity and tem-

perature, the external tempera-

ture alone is not sufficient to de-

tect ice.

You can access various settings:

– "Set the time zone automatically";

– "Set the time zone (manually)";

– "Use the 24-hour format";

– ...

1 4 0 - G e t t i n g t o k n o w y o u r v e h i c l e

WARNING LIGHTS

The display of information shown

below DEPENDS ON THE VEHICLE

EQUIPMENT AND COUNTRY.

The appearance of the

If no lights or sounds

are apparent, this indi-

cates a fault in the in-

warning light in-

dicates that you should drive

very carefully to an authorised

dealer as soon as possible. If

you fail to follow this recom-

mendation, you risk damaging

your vehicle.

2

strument panel. This in-

dicates that it is essential to

stop immediately (as soon as

traffic conditions allow). Ensure

that the vehicle is correctly im-

mobilised and contact an ap-

proved Dealer.

For your own safety,

Side light indicator light

the

warning

light requires you to

stop immediately, as soon as

traffic conditions allow. Switch

off the engine and do not

restart it. Call an approved

Dealer.

Dipped beam headlight indi-

cator light

Instrument panel A : this lights up

when the driver's door is opened. To

adjust the dashboard brightness, re-

fer to the multimedia instructions.

Main beam headlight tell-tale

light

In some cases, the appearance of a

warning light is accompanied by a

message.

Automatic main beam head-

light indicator light

Rear fog light tell-tale

Left-hand direction indicator

tell-tale light

Right-hand direction indica-

tor tell-tale light

G e t t i n g t o k n o w y o u r v e h i c l e - 1 4 1

WARNING LIGHTS

accompanied by a beep.

follow this recommendation, you risk

damaging your vehicle.

Bad weather warning light

For your own safety, it requires you

to stop immediately, as soon as traf-

fic conditions allow. Switch off the

engine and do not restart it.

Call an approved Dealer.

"Adaptive Vision" lights mal-

function warning light

Electrotechnical system

warning light

2

It lights up along with the

Door status warning light

warning light and a beep sounds

when the electrical assembly tem-

perature is too high. Stop the vehicle

and switch off the ignition. Consult

an approved Dealer.

Warning light

This lights up when the ignition is

switched on and goes out as soon as

the engine is switched on. The warn-

ing light may light up in conjunction

with other warning lights and/or

messages on the instrument panel.

It means you should drive very care-

fully to an approved dealer as soon

as possible. If you fail to follow this

recommendation, you risk damag-

ing your vehicle.

Electronic parking brake ap-

plied warning light ꢀ 179

"Autohold" system warning

Pedestrian horn fault warning

Front driver airbag and pas-

If it lights up accompanied by the

light

warning light, a beep and

the "EVACUATE IN SAFETY" mes-

sage, switch off the ignition and do

not restart the engine. Leave the ve-

hicle and consult an approved deal-

er.

senger ꢀ 119 fault warning light

Warning light

If it appears in red during driving and

Low windscreen washer level

warning light

is accompanied by the

warning light, you must, for your

safety, stop as soon as traffic condi-

tions allow. Switch off the engine

and do not restart it.

Automatic wiping function

warning light

Urgent stop warning light

This lights up when the ignition is

switched on and goes out as soon as

the engine is switched on. The warn-

ing light comes on with other warn-

ing lights and/or messages and is

Call an approved Dealer.

If it appears in yellow during driving

and is accompanied by the

warning light, visit an approved

dealer as soon as possible. Mean-

while, drive with care. If you fail to

1 4 2 - G e t t i n g t o k n o w y o u r v e h i c l e

WARNING LIGHTS

electrotechnical fault related to the

electrical assembly (traction battery

and electric motor). Contact your

approved Dealer straight away.

this means that the electrical circuit

is overcharged or discharged ꢀ 342.

The "EVACUATE IN

SAFETY" message ac-

companied by the

Limited performance warning

light

2

warning light

and a beep indicates that for

your safety you must stop the

vehicle immediately, depending

on the traffic conditions. Switch

off the ignition. Leave it

switched off. Exit the vehicle,

get all passengers out of the ve-

hicle and keep them away from

the vehicle and traffic.

Electric motor fault warning

light

When it comes on, this indicates a

fault with the electrotechnical sys-

tem linked to the electric motor.

Contact your approved Dealer

straight away.

This appears when the traction bat-

tery temporarily does not deliver its

nominal power. During this period,

vehicle performance is reduced.

Opt for a smoother driving style until

the warning light disappears.

Charging cord plugged in

warning light

This lights up when the charging ca-

ble is plugged into the vehicle ꢀ 20.

Traction battery gauge warn-

ing light

This appears in yellow when the

traction battery charge level has

reached the reserve threshold.

Fire hazards

Anti-lock braking warning

light

This lights up when the ignition is

switched on and goes out after a

few seconds.

If it does not go out after the ignition

is switched on, or lights up when dri-

ving, there is a fault with the ABS.

Braking will then be as normal, with-

out the ABS. Contact your approved

Dealer straight away.

Traction battery fault warn-

ing light

If it appears accompanied by the

If the vehicle is parked

on the hard shoulder,

you must warn other

warning light, it indicates a

fault related to the operation of the

traction battery. Contact your ap-

proved Dealer straight away.

road users of your

vehicle's presence with a warn-

ing triangle or with other de-

vices as per the legislation ap-

plying to the country you are in.

12 V battery charge warning

light

If it comes on, accompanied by the

Electronic Stability Program

(ESC) and traction control system

warning light

The warning light may appear for

several reasons.

Electrotechnical system fault

warning light

When it comes on, this indicates an

warning light and a beep,

G e t t i n g t o k n o w y o u r v e h i c l e - 1 4 3

WARNING LIGHTS

ing light and a beep, this indicates

that the fluid level in the circuit is low

or that there is a braking system

fault.

Stop as soon as traffic conditions al-

low and consult an approved Dealer.

Lane centring system warning

Electronic Stability Program

(ESC) and traction control system

unavailability warning light

light

2

Speed limiter warning light

Tyre under-inflation warning

light

This lights up when the ignition is

switched on or when the engine

starts, then disappears after a few

seconds ꢀ 189.

Adaptive cruise control warn-

ing light Stop and Go

Brake pedal warning light

This lights up when the brake pedal

should be depressed.

On display B

Charging programming warn-

ing light

"Hands-free parking" func-

tion warning light

Air conditioning programming

indicator

Variable power assisted

steering warning light

"Hands off steering wheel"

detection warning light

It lights up when the ignition or the

engine is switched on and goes off

after a few seconds.

If it lights up during driving and is ac-

"Advanced safety" function

fault or unavailability warning light

companied by the

warning

light, this indicates a system fault.

Call an approved Dealer.

Overspeed warning light

Lane departure system warn-

ing light

Brake circuit fault warning

light

Airbag passenger ON ꢀ 121

ꢀ 119

It lights up when the ignition or the

engine is switched on and goes off

after a few seconds.

Lane departure prevention

system warning light

Airbag passenger OFF ꢀ 121

If it lights up during braking and is

accompanied by the

warn-

1 4 4 - G e t t i n g t o k n o w y o u r v e h i c l e

WARNING LIGHTS

Front seat belt reminder warn-

ing light

2

On the rear view mirror C

(depending on the vehicle)

Rear view camera function

warning light ꢀ 150

G e t t i n g t o k n o w y o u r v e h i c l e - 1 4 5

STEERING

Activating the function

With the ignition on, press the button

5 on the multimedia screen 2 .

For safety reasons, on-

ly adjust the steering

wheel when the vehicle

is stationary.

Steering wheel

Adjusting the steering wheel

height and depth

2

Steering wheel heating

Deactivating the function

–

Automatically:

Lower the lever 1 and set the steer-

The function switches off automati-

cally after the regulation phase of

approximately 30 minutes.

ing wheel to the required position.

Then, raise the lever fully, beyond the

point of resistance to lock the steer-

ing wheel.

Make sure that the steering wheel is

correctly locked.

(depending on the vehicle)

This function heats the steering

wheel 4 .

–

Manually:

To deactivate the function during

the regulation phase, press the but-

ton 5 on the multimedia screen 2 .

Operating principle

When the temperature is reached,

the function regulates the tempera-

ture of the heated areas for approxi-

mately 30 minutes and then switch-

es off automatically.

Note: the function can also be ac-

cessed using the 3 "Favourites" but-

ton on the steering wheel 4 .

1 4 6 - G e t t i n g t o k n o w y o u r v e h i c l e

STEERING

Steering is made easier during park-

ing manoeuvres (for added comfort)

while the force needed to steer in-

creases progressively as the speed

rises (for enhanced safety at high

speeds).

"Favourites" function

2

Never switch off the ig-

nition when travelling

downhill, and avoid do-

ing so in normal driving

(power steering and brake ser-

vo will not function).

Depending on the vehicle, by press-

ing the steering wheel control 6 you

can activate the heated steering

wheel according to the stored use

settings that you have previously

defined.

For more information on program-

ming this function, please refer to

the multimedia instructions.

Never leave the steering

wheel on full lock when

the vehicle is stationary.

With the engine switched off, or

if there is a system fault, it is still

possible to turn the steering

wheel. The force required will be

greater.

A noise may be heard when the

steering wheel is moved quickly.

This is normal.

Power-assisted steering

The variable power-assisted steer-

ing system is equipped with an elec-

tronic control system which alters

the level of assistance to suit the ve-

hicle speed.

G e t t i n g t o k n o w y o u r v e h i c l e - 1 4 7

REAR VIEW

For safety reasons, car-

ry out any adjustments

while the vehicle is sta-

tionary.

Objects observed in

the rear view mirror

glass are actually clos-

er than they appear.

Rear view mirrors

Exterior rear view mirrors with

electrical adjustment:

2

For your safety, take this into

account in order to correctly as-

sess the distance before any

manoeuvre.

Electrical folding mirrors

The door mirrors will fold-out auto-

matically when the vehicle is un-

locked. The door mirrors fold in when

the vehicle is locked.

You can deactivate/activate auto-

matic folding of the door mirrors

ꢀ 139.

Rear view mirrors which tilt in re-

verse gear

You can force folding by pressing

the switch 1 . In this situation, the

door mirrors will remain folded until

the 1 button is pressed again, re-

gardless of automatic folding.

Select the door mirror using on of the

switches 3 , then use the switch 2 to

adjust it to the desired position.

Special case

When the rear view mirror has been

manually deployed or folded back, it

is possible to reset it to a usage posi-

tion.

Heated rear view mirrors

While the engine is running, mirror

de-icing is activated simultaneously

with the rear screen de-icing/

demisting.

To do this, press the switch 1 . A me-

chanical noise from the rear view

mirror unit will be heard.

If a tapping noise cannot be heard,

press the switch 1 again until the

tapping noise can be heard from the

door mirror.

For vehicles equipped with the

driver’s seat with position memory,

you can enter a specific setting for

the rear view mirrors when reversing

and store the position.

1 4 8 - G e t t i n g t o k n o w y o u r v e h i c l e

REAR VIEW

With the vehicle at a standstill and

reverse gear engaged, select the

door mirror using one of the switch-

es 3 , then use the switch 2 to adjust

it to the required position.

Select "Recall".

When driving at night, to avoid being

dazzled by the headlights of the ve-

hicle behind, shift the small lever 4

located behind the rear view mirror.

The positions of the exterior rear

view mirrors in forward gear, reverse

and of the front seats are recalled.

2

Auto-dimming rear view mirror 5

Returning to the driving position

For safety reasons, car-

ry out any adjustments

while the vehicle is sta-

tionary.

It is possible to move from the re-

verse gear to a forward gear:

– approximately nine seconds after

the reverse gear has been disen-

gaged when the speed is lower than

6 mph (10 km/h);

Interior rear view mirror

Its position can be adjusted.

– with the forward gear engaged

when the speed is greater than 6

mph (10 km/h);

Rear view mirror with lever 4

– when the engine is stopped.

Position memory

– Adjust the door mirrors (see previ-

ous paragraphs);

– refer to the multimedia instruc-

tions to access the settings memory.

Save the settings.

The positions of the exterior rear

view mirrors in forward and reverse

gear, and the position of the driver's

seat are saved simultaneously.

The rear view mirror automatically

darkens when you are being fol-

lowed by a vehicle using main beam

headlights or in very bright lighting.

Camera rear view

Depending on the vehicle, your rear

view mirror may be fitted with a dis-

play of the rear surroundings trans-

mitted by the camera fitted behind

the rear screen.

Recalling the memorised posi-

tion

Refer to the multimedia manual to

access recall of the saved position.

G e t t i n g t o k n o w y o u r v e h i c l e - 1 4 9

REAR VIEW

For more information, please see

ꢀ 150.

This function is an ad-

ditional aid. It cannot,

Camera rear view

Operating principle

therefore, under any

circumstances replace

the vigilance or the responsibili-

ty of the driver.

2

The driver should always be

ready for sudden incidents

while driving: always ensure

that there are no small, narrow

moving obstacles (such as a

child, animal, pushchair, bicycle,

stone, post, etc.) in the blind

spot when manoeuvring.

When the ignition is switched on, the

rear view mirror 2 mounted on the

roof centre console displays the

view behind the vehicle that is trans-

mitted by the camera 1 .

Adjusting the rear view mirror 2

If reflections reduce the visibility of

the view transmitted by the camera,

you can adjust the rear view mirror 2

to the left, right, upwards or down-

wards.

Note:

– the camera display 1 is transmit-

ted only if the rear view mirror is in

"screen" mode.

Depending on the vehicle, the rear

view may be displayed by the cam-

era 1 .

Direct rear view by mirror remains

available at all times.

The camera 1 is fitted behind the

rear screen, in the wiping area.

Make sure that the camera 1 is not

obscured (by dirt, mud, snow, con-

densation, etc.).

1 5 0 - G e t t i n g t o k n o w y o u r v e h i c l e

REAR VIEW

Operation

Switching off the function

Depending on your vision,

an adaptation time may

be necessary to focus on

the camera view display.

Objects which appear on the

edge of the door mirror 2 may

be distorted.

2

In very bright light (snow, vehi-

cle in sunshine, etc.), the cam-

era view may be partially dis-

turbed.

In low brightness or poor weath-

er, the image on the screen may

be distorted.

The camera's field of vision does not

cover the entire area behind the ve-

hicle, especially in the blind spot

area A .

The display switches off immediate-

ly after the ignition is switched off.

Note: the "mirror" mode can be acti-

vated using the lever 3 .

G e t t i n g t o k n o w y o u r v e h i c l e - 1 5 1

REAR VIEW

Operation

Adjusting the display and the

camera

d) adjusting the angle of rotation;

e) activating/deactivating the set-

tings menu display on the rear view

mirror;

2

f) selecting a language;

g) activating/deactivating button

backlighting.

Exit from the settings menu occurs

automatically after approximately

five seconds if no button is pressed.

For safety reasons,

carry out any adjust-

ments while the vehicle

is stationary.

Use the lever 3 to switch between

Adjust the system field of vision

and the door mirrors before dri-

ving. Be sure to adjust the cen-

tral rear view mirror before

switching to "screen" mode.

"mirror" mode and "screen" mode.

Press button 5 for "Menu" to access

the settings menu.

The green LED 4 as well as the pic-

togram displayed at the top right of

the rear view mirror indicates that

the screen mode is operating prop-

erly.

Repeatedly press buttons 6 and 7 to

scroll through the settings options.

Press the "OK" button 8 to access

the desired setting.

It disappears if you switch to "mir-

ror" mode or in the event of a fault.

Use buttons 6 and 7 " to adjust or ac-

tivate/deactivate the desired set-

ting.

Selecting the settings:

a) adjusting the brightness;

Each time the vehicle is

started, the function re-

turns to the settings

b) adjusting the vertical viewing an-

gle;

saved at the last engine stop.

c) adjusting the horizontal viewing

angle;

1 5 2 - G e t t i n g t o k n o w y o u r v e h i c l e

REAR VIEW

Special features related to the

reverse gear

Operating faults

2

When the system detects an operat-

When the vehicle is reversing, pay

attention to the images transmitted

by the reversing camera (multime-

dia screen 9 ) in addition to the infor-

mation available through the rear

view mirror ꢀ 275 as there remains a

rear view blind spot.

ing fault, the rear view mirror 2 turns

black, the symbol

displayed at

the top right of the rear view mirror

disappears and the LED 4 goes out.

This may be caused by a fault af-

fecting the camera or screen (clear-

ness, fixed image, delayed commu-

nication etc.).

If the black background persists,

switch to "mirror" mode and consult

an approved dealer.

G e t t i n g t o k n o w y o u r v e h i c l e - 1 5 3

LIGHTING AND SIGNALS

when the gear lever is in the P posi-

tion. Otherwise, the "Unavailable po-

sition lights" message is displayed

on the instrument panel to inform

you that it is not possible to activate

the side lights.

Exterior lighting and signals

Daytime running lights

2

Dipped beam headlights

Manual operation

Turn the ring 3 until the symbol is op-

posite the mark 2 .

This indicator light on the instrument

panel comes on.

Rotate the ring 3 until the AUTO

symbol is aligned with the mark 2 .

The daytime running lights come on

automatically (without any action

on the stalk 1 ) when the engine is

started and they switch off when the

engine is switched off.

Before driving at night,

check that the electri-

cal equipment is oper-

ating correctly and ad-

just the headlight beams (if your

vehicle is not carrying its nor-

mal load).

As a general precaution, check

that the lights are not obscured

(by dirt, mud, snow or objects

being transported).

Side lights

Turn the ring 3 until the sym-

bol is opposite the mark 2 .

This indicator light on the instrument

panel comes on.

Automatic operation

Note: depending on the vehicle, the

side lights can only be activated

manually when the parking brake is

applied or, depending on the vehicle,

Turn the ring 3 until the AUTO sym-

bol is opposite the mark 2 : with the

engine on, the dipped beam head-

1 5 4 - G e t t i n g t o k n o w y o u r v e h i c l e

LIGHTING AND SIGNALS

lights switch on or off automatically

according to the exterior light level,

without any action on the stalk 1 .

ment panel, the system is deactivat-

ed.

Consult an approved Dealer.

Additional cornering lighting

(depending on the vehicle)

In forward gear, if the dipped beam

or main beam headlights are on and

depending on the steering wheel an-

gle, this function adapts the beam

width to improve visibility on a bend

or at a junction.

Depending on the vehicle, the

2

dipped beam headlights will appear

automatically after several sweeps

of the windscreen wiper blades.

"Poor weather" function

(depending on the vehicle)

This function is part of the adaptive

front lighting system. It replaces the

use of the front fog lights. It may be

activated in foggy or snowy weather

or in any other case of poor visibility.

To activate this function, turn the

ring 3 until the AUTO symbol ap-

pears opposite the mark 2 , then

press the rotary switch to bring the

mark 4 in line with the symbol 5 .

When driving on the left-

hand side of the road in a

left-hand drive vehicle (or

vice versa), you must adjust

your headlights for the length of

your stay ꢀ 158.

Main beam headlights

Adaptive front lighting system

(depending on the vehicle)

Warning light

comes on the in-

This function automatically adjusts

the width and range of the dipped

beam headlights according to the

speed and weather conditions.

Turn the ring 3 until the AUTO sym-

bol is opposite the mark 2 : with the

engine on.

strument panel.

Switching off the lights

To deactivate the function, rotate

the rotary switch again so that the

mark 4 is opposite the symbol 5 .

This function can be deactivated, re-

fer to the multimedia instructions.

Operating faults

When the "Check Automatic Light-

ing" message appears on the instru-

The warning light

from the instrument panel.

The poor weather lights switch off

when the exterior lights are

switched off.

disappears

With the engine on and the

dipped beam headlights on, push

the stalk 1 (movement A ).

This indicator light on the instrument

panel comes on.

G e t t i n g t o k n o w y o u r v e h i c l e - 1 5 5

LIGHTING AND SIGNALS

To return to the dipped beam head-

lights position, push the stalk 1

again.

beam headlights automatically

switch off.

The main beam headlights come on

automatically if:

– the exterior light level is low;

– no other vehicle or lighting is de-

tected;

Note: push the stalk 1 to deactivate

the automatic daytime running

lights function, the

will disap-

2

pear from the instrument panel and

the main beam headlights will be ac-

tivated.

Automatic main beam head-

lights

– the vehicle speed is above approx-

imately 25 mph (40 km/h).

If any of the above conditions are

not fulfilled, the system switches to

dipped beam headlights.

Note: make sure that the wind-

screen is not obscured (dirt, mud,

snow, condensation, etc.).

The system may en-

counter difficulties under

certain conditions, includ-

ing:

– extreme weather conditions

(rain, snow, fog, etc.);

– obstruction in front of the

windscreen or camera;

– when a following or oncoming

vehicle has weak or hidden

lighting;

Activation/deactivation

To activate the automatic main

beam headlights

– incorrect settings for the

front headlights;

– reflecting systems;

– ...

Turn the ring 3 until the AUTO sym-

bol is next to the mark 2 , then press

the switch 6 .

Depending on the vehicle, this

system switches the main beam

headlights on and off

The warning light

appears on

automatically.

the instrument panel if the dipped

beam headlights are on.

It uses a camera located behind the

interior rear view mirror to detect ve-

hicles that are being followed and

those coming in the opposite direc-

tion.

Operating faults

If the "Check automatic lighting"

message appears on the instrument

panel, the system is deactivated.

To deactivate the automatic

main beam headlights

Note: at night, in urban areas with

street lighting, the automatic main

Consult an approved dealer.

Press the switch 6 , the

pears from the instrument panel.

disap-

1 5 6 - G e t t i n g t o k n o w y o u r v e h i c l e

LIGHTING AND SIGNALS

Activating/deactivating the func-

tion

For activation or deactivation of the

external welcome, refer to the multi-

media instructions.

Lights-on reminder buzzer

Using a portable navi-

gation system at night

in the windscreen area

If the lights are on after the engine is

switched off, a warning beep sounds

when the driver’s door is opened to

warn you that the lights are still on.

2

below the camera may

disturb the operation of the "au-

tomatic main beam headlights"

system (risk of reflection on the

windscreen).

"See-me-home lighting"

Operating faults

This function enables you to briefly

switch on the side lights and dipped

beam headlights (e.g. to provide

light when opening a gate).

Depending on the vehicle, if the

"Check lighting" message appears

along with the

warning light

With the engine stopped and the

lights switched off, after opening

the driver's door, the ring 3 in posi-

tion AUTO, pull the stalk 1 towards

you: the side lights and dipped beam

headlights will switch on for approxi-

mately 30 seconds along with the

and/or the

the instrument panel, this indicates

a lighting fault.

warning flashes on

The "automatic main

beam headlights" sys-

tem should under no

Consult an approved dealer.

circumstances be used

to replace the driver's attention

and responsibility with regard

to vehicle lighting and adapting

to light, visibility and traffic con-

ditions.

Welcome and goodbye function

(depending on the vehicle)

Once the function is activated, the

daytime running lights and the rear

side lights will light up automatically

upon detection of the card or when

the vehicle is unlocked.

They switch off automatically:

– approximately fifteen seconds af-

ter they are switched on;

warning lights

and

on

the instrument panel.

To increase this duration, you may

pull the stalk up to four times (total

time restricted to approximately

two minutes).

The "Lighting on during _ _ _" mes-

sage appears with the lighting time

on the instrument panel to confirm

the action.

You can then lock your vehicle.

Deactivating the "See-me-home

lighting" function

Switching off the lights

The lights will go out automatically

when the driver's door is opened or

the vehicle is locked, or one minute

after the engine is switched off.

In this case, the next time the engine

is started the lights will be switched

back on according to the position of

the ring 3 .

– when starting the engine, based

on the position of the lighting stalk;

or

– upon locking the vehicle.

G e t t i n g t o k n o w y o u r v e h i c l e - 1 5 7

LIGHTING AND SIGNALS

To switch off the lights before they

switch off automatically, turn the

ring 3 to any position, then return it

to position AUTO.

Note: if the Welcome and Goodbye

function is activated, once the en-

gine is switched off, the procedure

for deactivating the "See-me-home

lighting" function must be carried

out before pulling the stalk (other-

wise the lights remain lit by the Wel-

come and Goodbye function).

press the rotary switch to bring the

mark 4 in line with the symbol 7 .

When driving in fog or

snow, or when transport-

ing objects which are

Warning light

comes on the in-

2

strument panel.

higher than the roof, the head-

lights do not come on automati-

cally.

The fog lights are controlled by

the driver: the warning lights on

the instrument panel inform you

whether they are on (warning

light on) or off (warning light

off).

Operation of the fog lights depends

on the exterior lighting selected, and

an indicator light will light up on the

instrument panel.

To avoid inconveniencing other road

users, remember to switch off this

light when it is no longer needed.

Rear fog light

Switching off the lights

To deactivate the function, rotate

the rotary switch again so that the

mark 4 is opposite the symbol 7 .

Headlight beam adjustment

The warning light

disappears

from the instrument panel.

The rear fog lights switch off when

the exterior lights are switched off.

To activate this function, turn

the ring 3 until the AUTO symbol ap-

pears opposite the mark 2 , then

1 5 8 - G e t t i n g t o k n o w y o u r v e h i c l e

LIGHTING AND SIGNALS

Depending on the vehicle, the switch

A can be used to adjust the height of

the headlight beams according to

the load.

With the dipped beam headlights on,

press or raise switch A as many

times as required to select the re-

quired position on the instrument

panel. The position selected is dis-

played on the instrument panel for

approximately 15 seconds.

2

Note: if the lights are on, at each en-

gine start-up the selected position is

displayed on the instrument panel

for approximately 15 seconds.

When driving on the left in

a left-hand drive vehicle

(or vice versa), you must

adjust your lights temporarily

for the duration of your trip.

G e t t i n g t o k n o w y o u r v e h i c l e - 1 5 9

LIGHTING AND SIGNALS

Table of adjustment position examples

Examples of positions for adjusting the control A according to the

load

2

Driver alone or with front passenger

All seats occupied

0

1

Driver with passengers and luggage (or load)

reaching the maximum permissible all-up weight

2

3

Driver without passengers and luggage (or load)

reaching the maximum permissible all-up weight

The table below gives some examples. In all cases, adjust the control A according to the vehicle load so that the road

can be seen and other drivers are not dazzled.

1 6 0 - G e t t i n g t o k n o w y o u r v e h i c l e

LIGHTING AND SIGNALS

Return to the original position once

your trip is over: turn the bolt 1 a half

turn towards the + mark to raise the

beams.

Temporary adjustment

2

This can be adjusted using the multi-

media screen ꢀ 139.

Depending on the vehicle, the ad-

justment must be carried out manu-

ally.

Press or raise the switch A as many

times as required to select position 0

on the instrument panel.

Open the bonnet and identify the

marking B next to one of the front

headlight projectors.

Using a screwdriver or similar tool,

turn the bolt 1 a half turn towards

the ˗ mark to lower the beams.

G e t t i n g t o k n o w y o u r v e h i c l e - 1 6 1

AUDIBLE AND VISUAL SIGNALS

Horn

stalk will return to its original posi-

tion and the direction indicator light

concerned will flash three times.

2

Hazard warning lights

Press the steering wheel boss A to

sound the horn.

Headlight flasher

To flash the headlights, pull the stalk

1 towards you, then release.

Press the switch 2 . This switch

activates all four direction indica-

tors and the side indicator lights si-

multaneously.

It must only be used in an emer-

gency to warn drivers of other vehi-

cles that you have had to stop in an

area where stopping is prohibited or

unexpected, or that you are obliged

to drive under special conditions.

Direction indicators

Move the stalk 1 in the same direc-

tion as you want to move the steer-

ing wheel.

One-touch mode

Briefly shift the stalk 1 upwards or

downwards, not exceeding the point

of resistance, then release it: the

1 6 2 - G e t t i n g t o k n o w y o u r v e h i c l e

WIPER

Vehicle fitted with front wind-

screen wiper rain sensor

Windscreen wash, wipe

Vehicle fitted with intermittent

windscreen wipers

2

Special feature

When driving the vehicle, the wiping

speed slows down whenever the ve-

hicle stops.

For example, fast wiping speed will

slow to normal wiping speed.

As soon as the vehicle moves off,

wiping will return to the speed origi-

nally selected.

The rain sensor is located on the

windscreen, in front of the interior

rear view mirror.

A. a single sweep of the wipers

A short push will trigger one sweep

of the wipers.

A. a single sweep of the wipers

A short push will trigger one sweep

of the wipers.

B. stopping

B. off

Any action on the stalk 1 overrides

and cancels the automatic function.

C. intermittent wiping

The wipers will pause for several

seconds between sweeps. It is possi-

ble to change the interval between

sweeps by turning the ring 2 .

D. slow continuous wiping

E. fast continuous wiping

G e t t i n g t o k n o w y o u r v e h i c l e - 1 6 3

WIPER

– damaged windscreen wipers: a

film of water or traces left by a blade

in the sensor's detection zone may

increase the response time of the

automatic wiper, or increase the

wiping frequency;

– a windscreen with any chip or

crack near the sensor, or a wind-

screen covered in dust, dirt, insects,

ice, the use of washing wax and wa-

ter-repellent chemicals. The wind-

screen wiper will be less sensitive or

may even not react at all.

D. slow continuous wiping

E. fast continuous wiping

Special feature

When driving the vehicle, the wiping

speed slows down whenever the ve-

hicle stops.

For example, fast wiping speed will

slow to normal wiping speed.

As soon as the vehicle moves off,

wiping will return to the speed origi-

nally selected.

Any action on the stalk 1 overrides

and cancels the automatic function.

Precautions

The

warning light appears on

the instrument panel to confirm that

the function is activated.

Note:

2

– the rain sensor is only intended as

a driving aid. In the event of reduced

visibility, the driver should manually

activate the wipers. In foggy weath-

er or during snowfalls, wiping is not

automatically triggered and re-

mains under the driver's control;

– in the event of temperatures be-

low zero, automatic wiping is not ac-

tivated when the vehicle is started. It

is automatically activated as soon

as the vehicle exceeds a certain

speed (approximately 5 mph (8 km/

h));

C. automatic wiper function

When this position is selected, the

system detects water on the wind-

screen and triggers the wipers at a

suitable wiping speed.

– do not activate automatic wiping

in dry weather;

It is possible to change the trigger-

ing threshold and the interval be-

tween sweeps by turning the ring 2 :

– fully de-ice the windscreen before

activating automatic wiping;

– when washing using a roller type

car wash, return the stalk 1 to the off

position B to deactivate automatic

wiping.

–

F : maximum sensitivity;

G : minimum sensitivity.

The higher the sensitivity, the quick-

er the wipers will react and the

faster the wipe.

When activating automatic wiping

or when increasing sensitivity, one

sweep of the blades is performed.

Operating faults

In the event of a malfunction of the

automatic wiping, the wiper is set to

intermittent wiping. Call an ap-

proved dealer.

The rain sensor operation may be in-

terrupted in the event of:

– In the event of ice, check whether

the blades are stuck to the wind-

screen before operating the wiping

mechanism. If you activate the

wipers while the blades are stuck

1 6 4 - G e t t i n g t o k n o w y o u r v e h i c l e

WIPER

down with ice, you may risk damag-

ing both the blade and the wiper mo-

tor.

– Do not activate the wipers on a dry

screen. This will lead to premature

wear or damage to the blades.

Windscreen washer

Before any action in-

volving the windscreen

(washing the vehicle,

2

de-icing or cleaning the

windscreen, etc.) return the

stalk 1 to position B (park).

Risk of injury and/or damage.

Specific front wiper position (ser-

vice position)

This position enables the blades to

be lifted to remove them from the

windscreen.

It may be useful to:

– clean the blades;

– release the blades from the wind-

screen in winter;

– replace the blades ꢀ 362.

With the engine off or running, lift

the stalk 1 twice to position A (single

sweep).

The blades stop slightly away from

the bonnet.

In the event of obstacles

on the windscreen (dirt,

snow, ice etc.), clean the

windscreen (including the cen-

tral area located behind the in-

terior rear view mirror) before

starting the wipers (risk of mo-

tor overheating).

With the ignition on, pull the stalk 1

then release it.

A longer pull will trigger, in addition

to the windscreen washer, two

sweeps of the wipers followed, a few

seconds later, by a third.

If an object is preventing a

blade from moving, it may stop

functioning.

To return the blades to the lowered

position, with the ignition on, ensure

that the wipers have folded down

onto the windscreen, then move the

stalk 1 to position A (single sweep).

Before switching on the ignition,

place the wipers on the windscreen.

Otherwise, there may a risk of dam-

age to the bonnet or the wipers

when they are switched on.

Note:

Remove the obstacle and reac-

tivate the wiper using the wiper

stalk.

– A front washing action at stalk 1

lasting for more than 30 seconds

may cause the windscreen washer

pump to cut out. This prevents the

pump from overheating;

– in temperatures below zero, the

washer liquid risks freezing to the

windscreen, thereby reducing visibil-

ity. Heat the windscreen using the

demister control before cleaning.

G e t t i n g t o k n o w y o u r v e h i c l e - 1 6 5

WIPER

Rear windscreen wash, wiper

Rear windscreen wiper

When working in the

engine compartment,

ensure that the wind-

screen wiper stalk is in

Efficiency of a wiper

blade

Check the condition of

the wiper blades. How long they

last depends on you:

2

position B (stop).

Risk of injury.

– it must remain clean: clean

the blade and the screen regu-

larly with soapy water;

– do not use it when the screen

is dry;

– free it from the screen when it

has not been used for a long

time.

In all cases, replace it as soon as

it begins to lose efficiency: ap-

proximately once a year ꢀ 362.

Precaution for using the wipers

With the ignition on, rotate the

ring 3 on the stalk 1 until the symbol

is opposite the mark 2

– In freezing or snowy condi-

tions, clear the screen before

starting the wipers (risk of mo-

tor overheating);

– ensure that no objects are ob-

structing the travel of the blade.

–

off;

intermittent wiping;

The wipers will pause for several

seconds between sweeps. The wip-

ing frequency varies according to

the vehicle speed;

–

slow continuous wiping.

To stop the operation, rotate the ring

3 again.

1 6 6 - G e t t i n g t o k n o w y o u r v e h i c l e

WIPER

Note: when washing using a roller

type car wash, return the ring 3 on

the stalk 1 to the stop position to de-

activate automatic wiping.

are in operation). If your vehicle is

equipped with a vehicle settings

customisation menu, you can opt to

activate or deactivate this function

ꢀ 139.

For vehicles not fitted with a settings

customisation menu, you can have

this function deactivated by an au-

thorised dealer.

In the event of obstacles present on

the rear window (dirt, snow, etc.), the

wiper will try to sweep away all the

obstacles. If an obstacle prevents

the blade from moving, it can be

stopped. Remove the obstacle, wait

for around 30 seconds and reacti-

vate the wiper using the wiper stalk.

Efficiency of a wiper

blade

Check the condition of

the wiper blades. How long they

last depends on you:

2

Follow usage recommendations.

At the end of use, remember to re-

turn the rear wiper control to the

stop position, so that wiping is not in-

advertently activated during the

next use.

– it must remain clean: clean

the blade and the screen regu-

larly with soapy water;

– do not use it when the screen

is dry;

– free it from the screen when it

has not been used for a long

time.

Do not use the wiper arm

to open or close the tail-

gate.

In all cases, replace it as soon as

it begins to lose efficiency: ap-

proximately once a year ꢀ 362.

Precautions for using the

wipers

Precautions

Before taking any ac-

tion involving the rear

screen (washing the

– In the event of ice, check that the

blades are not stuck to the wind-

screen before operating the wipers.

If you activate the wiper while the

blade is blocked by ice, you risk dam-

aging both the blade and the wiping

motor.

– Do not operate the wipers on a dry

screen. This will lead to the prema-

ture wear or damage to the blades.

vehicle, de-icing, clean-

ing, etc.) return the stalk 1 to the

off position.

– In freezing or snowy condi-

tions, clear the screen before

starting the wipers (risk of mo-

tor overheating);

– ensure that no objects are ob-

structing the travel of the blade.

Risk of injury and/or damage.

Rear screen wash/wipe

Activation/deactivation of the rear

screen wiper

Engaging reverse gear triggers in-

termittent wiping (if the front wipers

With the ignition on, push and

hold the stalk 1 then release it.

G e t t i n g t o k n o w y o u r v e h i c l e - 1 6 7

WIPER

Holding the stalk for longer will trig-

ger (in addition to the windscreen

washer) two sweeps of the rear

wiper followed, a few seconds later,

by a third (drip wiping function).

2

When the stalk is released, it returns

to the rear wipe position.

Note: a rear washing action at stalk

1 lasting for more than 30 seconds

may cause the windscreen washer

pump to cut out. This prevents the

pump from overheating.

1 6 8 - G e t t i n g t o k n o w y o u r v e h i c l e

Getting to know your vehicle for Your Renault Scenic 4 Door Fifth Generation (2023-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals