Get Getting to know your vehicle -> Lighting and signals Guide for Renault Scenic 4 Door Fifth Generation (2023-2026)

LIGHTING AND SIGNALS

when the gear lever is in the P posi-

tion. Otherwise, the "Unavailable po-

sition lights" message is displayed

on the instrument panel to inform

you that it is not possible to activate

the side lights.

Exterior lighting and signals

Daytime running lights

2

Dipped beam headlights

Manual operation

Turn the ring 3 until the symbol is op-

posite the mark 2 .

This indicator light on the instrument

panel comes on.

Rotate the ring 3 until the AUTO

symbol is aligned with the mark 2 .

The daytime running lights come on

automatically (without any action

on the stalk 1 ) when the engine is

started and they switch off when the

engine is switched off.

Before driving at night,

check that the electri-

cal equipment is oper-

ating correctly and ad-

just the headlight beams (if your

vehicle is not carrying its nor-

mal load).

As a general precaution, check

that the lights are not obscured

(by dirt, mud, snow or objects

being transported).

Side lights

Turn the ring 3 until the sym-

bol is opposite the mark 2 .

This indicator light on the instrument

panel comes on.

Automatic operation

Note: depending on the vehicle, the

side lights can only be activated

manually when the parking brake is

applied or, depending on the vehicle,

Turn the ring 3 until the AUTO sym-

bol is opposite the mark 2 : with the

engine on, the dipped beam head-

1 5 4 - G e t t i n g t o k n o w y o u r v e h i c l e

LIGHTING AND SIGNALS

lights switch on or off automatically

according to the exterior light level,

without any action on the stalk 1 .

ment panel, the system is deactivat-

ed.

Consult an approved Dealer.

Additional cornering lighting

(depending on the vehicle)

In forward gear, if the dipped beam

or main beam headlights are on and

depending on the steering wheel an-

gle, this function adapts the beam

width to improve visibility on a bend

or at a junction.

Depending on the vehicle, the

2

dipped beam headlights will appear

automatically after several sweeps

of the windscreen wiper blades.

"Poor weather" function

(depending on the vehicle)

This function is part of the adaptive

front lighting system. It replaces the

use of the front fog lights. It may be

activated in foggy or snowy weather

or in any other case of poor visibility.

To activate this function, turn the

ring 3 until the AUTO symbol ap-

pears opposite the mark 2 , then

press the rotary switch to bring the

mark 4 in line with the symbol 5 .

When driving on the left-

hand side of the road in a

left-hand drive vehicle (or

vice versa), you must adjust

your headlights for the length of

your stay ꢀ 158.

Main beam headlights

Adaptive front lighting system

(depending on the vehicle)

Warning light

comes on the in-

This function automatically adjusts

the width and range of the dipped

beam headlights according to the

speed and weather conditions.

Turn the ring 3 until the AUTO sym-

bol is opposite the mark 2 : with the

engine on.

strument panel.

Switching off the lights

To deactivate the function, rotate

the rotary switch again so that the

mark 4 is opposite the symbol 5 .

This function can be deactivated, re-

fer to the multimedia instructions.

Operating faults

When the "Check Automatic Light-

ing" message appears on the instru-

The warning light

from the instrument panel.

The poor weather lights switch off

when the exterior lights are

switched off.

disappears

With the engine on and the

dipped beam headlights on, push

the stalk 1 (movement A ).

This indicator light on the instrument

panel comes on.

G e t t i n g t o k n o w y o u r v e h i c l e - 1 5 5

LIGHTING AND SIGNALS

To return to the dipped beam head-

lights position, push the stalk 1

again.

beam headlights automatically

switch off.

The main beam headlights come on

automatically if:

– the exterior light level is low;

– no other vehicle or lighting is de-

tected;

Note: push the stalk 1 to deactivate

the automatic daytime running

lights function, the

will disap-

2

pear from the instrument panel and

the main beam headlights will be ac-

tivated.

Automatic main beam head-

lights

– the vehicle speed is above approx-

imately 25 mph (40 km/h).

If any of the above conditions are

not fulfilled, the system switches to

dipped beam headlights.

Note: make sure that the wind-

screen is not obscured (dirt, mud,

snow, condensation, etc.).

The system may en-

counter difficulties under

certain conditions, includ-

ing:

– extreme weather conditions

(rain, snow, fog, etc.);

– obstruction in front of the

windscreen or camera;

– when a following or oncoming

vehicle has weak or hidden

lighting;

Activation/deactivation

To activate the automatic main

beam headlights

– incorrect settings for the

front headlights;

– reflecting systems;

– ...

Turn the ring 3 until the AUTO sym-

bol is next to the mark 2 , then press

the switch 6 .

Depending on the vehicle, this

system switches the main beam

headlights on and off

The warning light

appears on

automatically.

the instrument panel if the dipped

beam headlights are on.

It uses a camera located behind the

interior rear view mirror to detect ve-

hicles that are being followed and

those coming in the opposite direc-

tion.

Operating faults

If the "Check automatic lighting"

message appears on the instrument

panel, the system is deactivated.

To deactivate the automatic

main beam headlights

Note: at night, in urban areas with

street lighting, the automatic main

Consult an approved dealer.

Press the switch 6 , the

pears from the instrument panel.

disap-

1 5 6 - G e t t i n g t o k n o w y o u r v e h i c l e

LIGHTING AND SIGNALS

Activating/deactivating the func-

tion

For activation or deactivation of the

external welcome, refer to the multi-

media instructions.

Lights-on reminder buzzer

Using a portable navi-

gation system at night

in the windscreen area

If the lights are on after the engine is

switched off, a warning beep sounds

when the driver’s door is opened to

warn you that the lights are still on.

2

below the camera may

disturb the operation of the "au-

tomatic main beam headlights"

system (risk of reflection on the

windscreen).

"See-me-home lighting"

Operating faults

This function enables you to briefly

switch on the side lights and dipped

beam headlights (e.g. to provide

light when opening a gate).

Depending on the vehicle, if the

"Check lighting" message appears

along with the

warning light

With the engine stopped and the

lights switched off, after opening

the driver's door, the ring 3 in posi-

tion AUTO, pull the stalk 1 towards

you: the side lights and dipped beam

headlights will switch on for approxi-

mately 30 seconds along with the

and/or the

the instrument panel, this indicates

a lighting fault.

warning flashes on

The "automatic main

beam headlights" sys-

tem should under no

Consult an approved dealer.

circumstances be used

to replace the driver's attention

and responsibility with regard

to vehicle lighting and adapting

to light, visibility and traffic con-

ditions.

Welcome and goodbye function

(depending on the vehicle)

Once the function is activated, the

daytime running lights and the rear

side lights will light up automatically

upon detection of the card or when

the vehicle is unlocked.

They switch off automatically:

– approximately fifteen seconds af-

ter they are switched on;

warning lights

and

on

the instrument panel.

To increase this duration, you may

pull the stalk up to four times (total

time restricted to approximately

two minutes).

The "Lighting on during _ _ _" mes-

sage appears with the lighting time

on the instrument panel to confirm

the action.

You can then lock your vehicle.

Deactivating the "See-me-home

lighting" function

Switching off the lights

The lights will go out automatically

when the driver's door is opened or

the vehicle is locked, or one minute

after the engine is switched off.

In this case, the next time the engine

is started the lights will be switched

back on according to the position of

the ring 3 .

– when starting the engine, based

on the position of the lighting stalk;

or

– upon locking the vehicle.

G e t t i n g t o k n o w y o u r v e h i c l e - 1 5 7

LIGHTING AND SIGNALS

To switch off the lights before they

switch off automatically, turn the

ring 3 to any position, then return it

to position AUTO.

Note: if the Welcome and Goodbye

function is activated, once the en-

gine is switched off, the procedure

for deactivating the "See-me-home

lighting" function must be carried

out before pulling the stalk (other-

wise the lights remain lit by the Wel-

come and Goodbye function).

press the rotary switch to bring the

mark 4 in line with the symbol 7 .

When driving in fog or

snow, or when transport-

ing objects which are

Warning light

comes on the in-

2

strument panel.

higher than the roof, the head-

lights do not come on automati-

cally.

The fog lights are controlled by

the driver: the warning lights on

the instrument panel inform you

whether they are on (warning

light on) or off (warning light

off).

Operation of the fog lights depends

on the exterior lighting selected, and

an indicator light will light up on the

instrument panel.

To avoid inconveniencing other road

users, remember to switch off this

light when it is no longer needed.

Rear fog light

Switching off the lights

To deactivate the function, rotate

the rotary switch again so that the

mark 4 is opposite the symbol 7 .

Headlight beam adjustment

The warning light

disappears

from the instrument panel.

The rear fog lights switch off when

the exterior lights are switched off.

To activate this function, turn

the ring 3 until the AUTO symbol ap-

pears opposite the mark 2 , then

1 5 8 - G e t t i n g t o k n o w y o u r v e h i c l e

LIGHTING AND SIGNALS

Depending on the vehicle, the switch

A can be used to adjust the height of

the headlight beams according to

the load.

With the dipped beam headlights on,

press or raise switch A as many

times as required to select the re-

quired position on the instrument

panel. The position selected is dis-

played on the instrument panel for

approximately 15 seconds.

2

Note: if the lights are on, at each en-

gine start-up the selected position is

displayed on the instrument panel

for approximately 15 seconds.

When driving on the left in

a left-hand drive vehicle

(or vice versa), you must

adjust your lights temporarily

for the duration of your trip.

G e t t i n g t o k n o w y o u r v e h i c l e - 1 5 9

LIGHTING AND SIGNALS

Table of adjustment position examples

Examples of positions for adjusting the control A according to the

load

2

Driver alone or with front passenger

All seats occupied

0

1

Driver with passengers and luggage (or load)

reaching the maximum permissible all-up weight

2

3

Driver without passengers and luggage (or load)

reaching the maximum permissible all-up weight

The table below gives some examples. In all cases, adjust the control A according to the vehicle load so that the road

can be seen and other drivers are not dazzled.

1 6 0 - G e t t i n g t o k n o w y o u r v e h i c l e

LIGHTING AND SIGNALS

Return to the original position once

your trip is over: turn the bolt 1 a half

turn towards the + mark to raise the

beams.

Temporary adjustment

2

This can be adjusted using the multi-

media screen ꢀ 139.

Depending on the vehicle, the ad-

justment must be carried out manu-

ally.

Press or raise the switch A as many

times as required to select position 0

on the instrument panel.

Open the bonnet and identify the

marking B next to one of the front

headlight projectors.

Using a screwdriver or similar tool,

turn the bolt 1 a half turn towards

the ˗ mark to lower the beams.

G e t t i n g t o k n o w y o u r v e h i c l e - 1 6 1

Getting to know your vehicle -> Lighting and signals for Your Renault Scenic 4 Door Fifth Generation (2023-2026)

Related Topics

Popular Owner Manuals

Latest Owner Manuals