2009-2015 Honda Jazz 4 Door Maintenance -> Spark Plugs User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Maintenance -> Spark Plugs for Your Honda Jazz 4 Door Second Generation (2009-2015)

07/09/12 09:50:03 32SAA650_306  
Spark Plugs  
The spark plugs in your vehicle  
should be replaced according to the  
time and distance recommendations  
in the maintenance schedule.  
Replacement  
(Except 1.5 SOHC VTEC engine  
model)  
BOLTS  
CONNECTOR  
LOCK TAB  
BOLT  
IGNITION COIL  
1. Remove the two holding bolts by  
using a wrench. Remove the cover  
by pulling it straight up.  
3. Use a wrench to remove the bolt  
holding the ignition coil. Remove  
the ignition coil by pulling it  
straight out.  
4. Disconnect the wire connector  
from the ignition coil by pushing  
on the lock tab and pulling on the  
connector. Pull on the plastic  
connector, not the wires.  
CONTINUED  
2. Clean off any dirt and oil that have  
collected around the ignition coils.  
303  
Maintenance  
Downloaded from engine  
07/09/12 09:50:10 32SAA650_307  
Spark Plugs  
5. Remove the spark plug with a 16  
mm (5/8 inch) spark plug socket.  
6. Put the new spark plug into the  
socket, then screw it into the hole.  
Screw it in by hand so you do not  
crossthread it.  
7. Torque the spark plug. (If you do  
not have a torque wrench, tighten  
the spark plug 2/3 of a turn after it  
contacts the cylinder head.)  
Tightening torque:  
18 N·m (1.8 kgf·m , 13 lbf·ft)  
304  
Maintenance  
Downloaded from engine  
07/09/12 09:50:19 32SAA650_308  
Spark Plugs  
Specifications:  
1.2 engine model, 1.3 engine  
model, 1.4 engine model and 1.5  
SOHC engine model  
Tighten the spark plugs carefully. A  
spark plug that is too loose can  
overheat and damage the engine.  
Overtightening can cause damage to  
the threads in the cylinder head.  
IGNITION COILS  
NGK:  
BKR6E-11  
DENSO: K20PR-U11  
Spark Plug Gap:  
1.1 mm (0.04 in)  
＋0  
－0.1 mm  
8. Install the ignition coil. Reinstall  
the bolt.  
9. Push the wire connector onto the  
ignition coil. Make sure it locks in  
place.  
10.Repeat this procedure for the  
other seven spark plugs.  
11.Reinstall the cover. Secure the  
cover by tightening the two  
holding bolts with a wrench.  
CONTINUED  
305  
Maintenance  
Downloaded from engine  
07/09/12 09:50:28 32SAA650_309  
Spark Plugs  
Replacement  
(1.5 SOHC VTEC engine model)  
BOLT  
CONNECTOR  
BOLTS  
LOCK TAB IGNITION COIL  
1. Remove the two holding bolts by  
using a wrench. Remove the cover  
by pulling it straight up.  
3. Use a wrench to remove the bolt  
holding the ignition coil. Remove  
the ignition coil by pulling it  
straight out.  
5. Remove the spark plug with a 16  
mm (5/8 inch) spark plug socket.  
2. Clean off any dirt and oil that have  
collected around the ignition coils.  
4. Disconnect the wire connector  
from the ignition coil by pushing  
on the lock tab and pulling on the  
connector. Pull on the plastic  
connector, not the wires.  
306  
Maintenance  
Downloaded from engine  
07/09/12 09:50:36 32SAA650_310  
Spark Plugs  
Tighten the spark plugs carefully. A  
spark plug that is too loose can  
overheat and damage the engine.  
Overtightening can cause damage to  
the threads in the cylinder head.  
8. Push the wire connector onto the  
ignition coil. Make sure it locks in  
place.  
9. Install the ignition coil. Reinstall  
the bolt.  
6. Put the new spark plug into the  
socket, then screw it into the hole.  
Screw it in by hand so you do not  
crossthread it.  
7. Torque the spark plug. (If you do  
not have a torque wrench, tighten  
the spark plug 2/3 of a turn after it  
contacts the cylinder head.)  
Tightening torque:  
18 N·m (1.8 kgf·m , 13 lbf·ft)  
CONTINUED  
307  
Maintenance  
Downloaded from engine  
07/09/12 09:50:44 32SAA650_311  
Spark Plugs  
Specifications:  
1.5 SOHC VTEC engine model  
NGK:  
DENSO:  
IZFR6K13  
SKJ20DR-M13  
IGNITION COILS  
Iridium spark plug does not need  
the gap adjustment.  
Brazil, Argentina, Chile models  
NGK:  
DENSO:  
ZFR6J-11  
KJ20CR-L11  
Spark Plug Gap:  
1.1 mm (0.04 in)  
＋0  
－0.1 mm  
10.Repeat this procedure for the  
other three spark plugs.  
11.Reinstall the cover. Secure the  
cover by tightening the two  
holding bolts with a wrench.  
308  
Maintenance  
Downloaded from engine  

Related Topics

Maintenance
Maintenance Schedule Required Maintenance Record Owner Maintenance Checks Fluid Locations Engine Oil Adding Oil Recommended Oil Additives Changing the Oil and Filter Cooling System Adding Engine Coolant Replacing Engine Coolant Windscreen Washers Transmission Fluid Automatic Transmission (CVT) Manual Transmission Brake and Clutch Fluid Brake System Clutch System Air Cleaner Element Fuel Filter Bonnet Latch Replacement Specifications Battery Replacing the Battery Wiper Blades Air Conditioning System Dust and Pollen Filter Drive Belts Tyres Inflation Inspection Maintenance Tyre Rotation Replacing Tyres and Wheels Wheels and Tyres Winter Tyres Tyre Chains Lights Headlight Aiming Headlights with High Voltage Discharge Tubes Replacing Bulbs Storing Your Vehicle

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot