2006-2014 Nissan Qashqai SUV Maintenance and do-it-yourself -> Changing engine oil User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Maintenance and do-it-yourself -> Changing engine oil for Your Nissan Qashqai SUV First Generation (2006-2014)

1. Park the vehicle on a level surface and apply the  
handbrake.  
It is normal to add some engine oil between oil  
maintenance intervals depending on the severity  
of operating conditions or depending on the prop-  
erty of the engine oil used. More engine oil is  
consumed by frequent acceleration/deceleration  
especially when the engine rpm is high. Con-  
sumption is likely to be higher when the engine  
is new. If the rate of oil consumption, after hav-  
ing driven for 5,000 km (3,000 miles), is more  
than 0.5 litre per 1,000 km (621 miles), consult a  
NISSAN dealer or qualified workshop.  
Store used engine oil in marked containers  
out of the reach of children.  
•
2. Start the engine. If the engine is cold, start and  
let the engine idle until it reaches the operational  
temperature.  
3. Turn the engine off.  
4. Wait at least 10 minutes for the engine oil to  
drain back into the oil pan.  
5. Open the bonnet. For details, see “Bonnet  
release” in the “3. Pre-driving checks and  
adjustments” section.  
NDI653Z  
CHANGING ENGINE OIL  
HR16DE or MR20DE engine  
6. Remove the dipstick and wipe it clean.  
WARNING  
Models with M9R engine: the engine oil dipstick  
is attached to the engine oil filler cap. Remove  
the engine oil filler cap and wipe the dipstick  
clean.  
NISSAN recommends contacting a NISSAN  
dealer or qualified workshop for engine oil  
servicing.  
•
NISSAN GREEN PROGRAM  
7. Reinsert it all the way.  
Used oil must not be poured into the ground,  
canals, rivers, etc. It should be disposed of at  
a rubbish tip having proper facilities. Check  
your local regulations.  
Models with M9R engine: install the engine oil  
filler cap.  
8. Remove the dipstick again and check the oil level.  
NDI509Z  
It should be in the normal range j1 .  
Be careful not to burn yourself, as the engine  
oil is hot.  
•
Euro 4 K9K engine  
9. If the oil level is below MIN j2 , remove the en-  
gine oil filler cap and pour the recommended oil  
through the opening. Do not overfill j3 .  
Prolonged and repeated contact with used  
engine oil may cause skin cancer.  
•
10. Recheck the oil level with the dipstick.  
11. Install the engine oil filler cap securely.  
12. Close the bonnet.  
Avoid direct skin contact with used oil. If skin  
•
contact is made, wash thoroughly with soap  
or hand cleaner and plenty of water as soon  
as possible.  
Maintenance and do-it-yourself 8-9  
Downloaded from manuals search engine  
4. Open the bonnet. For details, see “Bonnet  
release” in the “3. Pre-driving checks and  
adjustments” section.  
Drain plug tightening torques:  
HR16DE, MR20DE engine:  
34.3 N•m (3.5 kg-m, 25 ft-lb)  
K9K engine:  
5. Remove the engine oil filler cap.  
20 N•m (2.1 kg-m, 15 ft-lb)  
M9R engine:  
6. Raise and support the vehicle using a suitable  
floor jack and safety jack stands.  
44 N•m (4.5 kg-m, 32 ft-lb)  
R9M engine:  
Place the safety jack stands under the vehicle  
jack-up points.  
50 N•m (5.1 kg-m, 36.9 ft-lb)  
NDI1064  
For details, see “Flat tyre” in the “6. In case of  
emergency” section.  
11. Refill the engine with recommended engine oil  
and quantity.  
Euro 5 K9K engine  
7. Remove the engine compartment under cover.  
8. Place a large drain pan under the drain plug.  
See  
“Capacities  
and  
recommended  
fuel/lubricants” in the “9. Technical information”  
section.  
9. Remove the drain plug with a wrench and com-  
pletely drain the oil.  
12. Check the oil level with the dipstick. For details,  
see “Checking engine oil level” earlier in this  
section. If necessary, add engine oil.  
If the engine oil filter needs to be changed, re-  
move and replace it at this time. See “Changing  
engine oil filter” later in this section.  
13. Install the engine oil filler cap securely.  
14. Start the engine.  
10. Clean and re-install the drain plug along with a  
new washer. Securely tighten the drain plug  
with a wrench. Do not use excessive force.  
NDI978Z  
15. Check for any leakage around the drain plug.  
Correct as required.  
M9R or R9M engine  
1. Park the vehicle on a level surface and apply the  
handbrake.  
16. Turn the engine off and wait several minutes.  
17. Check the oil level again with the dipstick. If  
necessary, add engine oil.  
2. Start the engine. If the engine is cold, start and  
let the engine idle until the engine temperature  
reaches the operational temperature.  
18. Install the engine compartment under cover.  
19. Lower the vehicle carefully to the ground.  
20. Close the bonnet.  
3. Turn the engine off and wait at least 10 minutes  
to let the engine oil drain back into the oil pan.  
8-10 Maintenance and do-it-yourself  
Downloaded from manuals search engine  

Related Topics

Popular Owner Manuals