2006-2014 Nissan Qashqai SUV Maintenance and do-it-yourself -> Engine oil User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Maintenance and do-it-yourself -> Engine oil for Your Nissan Qashqai SUV First Generation (2006-2014)

ENGINE OIL  
CHECKING ENGINE OIL LEVEL  
CAUTION  
The oil level should be checked regularly. Oper-  
ating with an insufficient amount of oil can dam-  
age the engine, and such damage is not covered  
by warranty.  
NDI1061  
NDI1266  
Euro 5 K9K engine  
R9M engine  
NDI983Z  
HR16DE or MR20DE engine  
NDI976Z  
NDI1265  
M9R engine  
HR16DE or MR20DE engine  
K9K engine  
jA  
jB  
jC  
jD  
j1  
j2  
j3  
M9R engine  
R9M engine  
NDI984Z  
Euro 4 K9K engine  
Normal range  
MIN level  
MAX level  
8-8 Maintenance and do-it-yourself  
Downloaded from manuals search engine  
1. Park the vehicle on a level surface and apply the  
handbrake.  
It is normal to add some engine oil between oil  
maintenance intervals depending on the severity  
of operating conditions or depending on the prop-  
erty of the engine oil used. More engine oil is  
consumed by frequent acceleration/deceleration  
especially when the engine rpm is high. Con-  
sumption is likely to be higher when the engine  
is new. If the rate of oil consumption, after hav-  
ing driven for 5,000 km (3,000 miles), is more  
than 0.5 litre per 1,000 km (621 miles), consult a  
NISSAN dealer or qualified workshop.  
Store used engine oil in marked containers  
out of the reach of children.  
•
2. Start the engine. If the engine is cold, start and  
let the engine idle until it reaches the operational  
temperature.  
3. Turn the engine off.  
4. Wait at least 10 minutes for the engine oil to  
drain back into the oil pan.  
5. Open the bonnet. For details, see “Bonnet  
release” in the “3. Pre-driving checks and  
adjustments” section.  
NDI653Z  
CHANGING ENGINE OIL  
HR16DE or MR20DE engine  
6. Remove the dipstick and wipe it clean.  
WARNING  
Models with M9R engine: the engine oil dipstick  
is attached to the engine oil filler cap. Remove  
the engine oil filler cap and wipe the dipstick  
clean.  
NISSAN recommends contacting a NISSAN  
dealer or qualified workshop for engine oil  
servicing.  
•
NISSAN GREEN PROGRAM  
7. Reinsert it all the way.  
Used oil must not be poured into the ground,  
canals, rivers, etc. It should be disposed of at  
a rubbish tip having proper facilities. Check  
your local regulations.  
Models with M9R engine: install the engine oil  
filler cap.  
8. Remove the dipstick again and check the oil level.  
NDI509Z  
It should be in the normal range j1 .  
Be careful not to burn yourself, as the engine  
oil is hot.  
•
Euro 4 K9K engine  
9. If the oil level is below MIN j2 , remove the en-  
gine oil filler cap and pour the recommended oil  
through the opening. Do not overfill j3 .  
Prolonged and repeated contact with used  
engine oil may cause skin cancer.  
•
10. Recheck the oil level with the dipstick.  
11. Install the engine oil filler cap securely.  
12. Close the bonnet.  
Avoid direct skin contact with used oil. If skin  
•
contact is made, wash thoroughly with soap  
or hand cleaner and plenty of water as soon  
as possible.  
Maintenance and do-it-yourself 8-9  
Downloaded from manuals search engine  
4. Open the bonnet. For details, see “Bonnet  
release” in the “3. Pre-driving checks and  
adjustments” section.  
Drain plug tightening torques:  
HR16DE, MR20DE engine:  
34.3 N•m (3.5 kg-m, 25 ft-lb)  
K9K engine:  
5. Remove the engine oil filler cap.  
20 N•m (2.1 kg-m, 15 ft-lb)  
M9R engine:  
6. Raise and support the vehicle using a suitable  
floor jack and safety jack stands.  
44 N•m (4.5 kg-m, 32 ft-lb)  
R9M engine:  
Place the safety jack stands under the vehicle  
jack-up points.  
50 N•m (5.1 kg-m, 36.9 ft-lb)  
NDI1064  
For details, see “Flat tyre” in the “6. In case of  
emergency” section.  
11. Refill the engine with recommended engine oil  
and quantity.  
Euro 5 K9K engine  
7. Remove the engine compartment under cover.  
8. Place a large drain pan under the drain plug.  
See  
“Capacities  
and  
recommended  
fuel/lubricants” in the “9. Technical information”  
section.  
9. Remove the drain plug with a wrench and com-  
pletely drain the oil.  
12. Check the oil level with the dipstick. For details,  
see “Checking engine oil level” earlier in this  
section. If necessary, add engine oil.  
If the engine oil filter needs to be changed, re-  
move and replace it at this time. See “Changing  
engine oil filter” later in this section.  
13. Install the engine oil filler cap securely.  
14. Start the engine.  
10. Clean and re-install the drain plug along with a  
new washer. Securely tighten the drain plug  
with a wrench. Do not use excessive force.  
NDI978Z  
15. Check for any leakage around the drain plug.  
Correct as required.  
M9R or R9M engine  
1. Park the vehicle on a level surface and apply the  
handbrake.  
16. Turn the engine off and wait several minutes.  
17. Check the oil level again with the dipstick. If  
necessary, add engine oil.  
2. Start the engine. If the engine is cold, start and  
let the engine idle until the engine temperature  
reaches the operational temperature.  
18. Install the engine compartment under cover.  
19. Lower the vehicle carefully to the ground.  
20. Close the bonnet.  
3. Turn the engine off and wait at least 10 minutes  
to let the engine oil drain back into the oil pan.  
8-10 Maintenance and do-it-yourself  
Downloaded from manuals search engine  
3. Remove the engine oil filter unit.  
CHANGING ENGINE OIL FILTER  
HR16DE, MR20DE or K9K engine  
4. Wipe the engine oil filter mounting surface with a  
clean rag.  
WARNING  
NISSAN recommends contacting a NISSAN  
dealer or qualified workshop for engine oil fil-  
ter servicing.  
•
CAUTION  
If any oil is spilled on the engine or the ve-  
hicle, thoroughly wipe it clean.  
NISSAN GREEN PROGRAM  
Installation:  
A used oil filter should be disposed of at a  
rubbish tip having proper facilities.  
1. Clean and re-install the drain plug along with a  
new washer. For tightening torque details, see  
“Changing engine oil” earlier in this section.  
NDI656Z  
HR16DE or MR20DE engine  
2. Coat the rubber gasket on the new engine oil fil-  
ter unit with clean engine oil.  
3. Install the engine oil filter unit by hand until a  
slight resistance is felt, then tighten additionally  
2/3 of a turn.  
Engine oil filter tightening torques:  
HR16DE, MR20DE engine:  
17.7 N•m (1.8 kg-m, 13 ft-lb)  
K9K engine:  
14 N•m (1.4 kg-m, 10 ft-lb)  
NDI985Z  
4. Add engine oil and check the oil level with the  
engine oil dipstick. For details, see “Checking  
engine oil level” earlier in this section and “Ca-  
pacities and recommended fuel/lubricants” in the  
“9. Technical information” section.  
K9K engine  
Removal:  
1. Drain the engine oil. For details, see “Changing  
engine oil” earlier in this section.  
2. Loosen the engine oil filter unit with an oil filter  
wrench. Depending on the engine model, a spe-  
cial cap type wrench may be required. See a  
NISSAN dealer or qualified workshop, if in doubt.  
5. Install the engine oil filler cap.  
6. Start the engine.  
Maintenance and do-it-yourself 8-11  
Downloaded from manuals search engine  
7. After the engine has been warmed up, make sure  
there are no leaks around the engine oil filter unit  
and the drain plug. Correct as required.  
5. Wipe the oil filter cover entirely with a clean rag.  
M9R or R9M engine  
Installation:  
1. Clean and re-install the drain plug along with a  
new washer. For tightening torque details, see  
“Changing engine oil” earlier in this section.  
8. Turn the engine off and wait several minutes.  
Check the oil level and add engine oil, if neces-  
sary.  
2. Install the rubber O-ring, in its housing, on the  
outside of the engine oil filter cover.  
9. Install the engine compartment under cover.  
10. Lower the vehicle carefully to the ground.  
11. Close the bonnet.  
3. Insert the new oil filter element into the engine oil  
filter cover.  
NDI981Z  
4. Coat the rubber O-ring with clean engine oil.  
M9R  
5. Install the engine oil filter cover until a slight re-  
sistance is felt, then tighten additionally 2/3 of a  
turn.  
Tightening torque:  
25 N•m (2.6 kg-m, 18 ft-lb)  
6. Add engine oil and check the oil level with the  
engine oil dipstick. For details, see “Checking  
engine oil level” earlier in this section and “Ca-  
pacities and recommended fuel/lubricants” in the  
“9. Technical information” section.  
NDI1267  
7. Install the engine oil filler cap.  
8. Start the engine.  
R9M  
Removal:  
9. After the engine has been warmed up, make sure  
there are no leaks around the engine oil filter  
cover and the drain plug. Correct as required.  
1. Drain the engine oil. For details, see “Changing  
engine oil” earlier in this section.  
2. Loosen the engine oil filter cover with a wrench.  
10. Turn the engine off and wait several minutes.  
Check the oil level and add engine oil, if neces-  
sary.  
3. Remove the engine oil filter cover then the oil fil-  
ter element.  
4. Remove the rubber O-ring from the filter cover.  
11. Install the engine compartment undercover.  
8-12 Maintenance and do-it-yourself  
Downloaded from manuals search engine  
FUEL FILTER (Diesel engine  
models)  
12. Lower the vehicle carefully to the ground.  
13. Close the bonnet.  
Drained water is mixed with fuel and take  
precautions to prevent the fuel from ad-  
hering to rubber parts such as engine  
mounting insulator.  
•
DRAINING WATER  
PROTECT THE ENVIRONMENT  
4. After draining, close the drain plug manually.  
NISSAN GREEN PROGRAM  
CAUTION  
It is illegal to pollute drains, water courses and soil.  
Use authorised waste collection facilities, including  
civic amenity sites and garages providing facilities  
for the disposal of used oil and used oil filters. If in  
doubt, contact your local authority for advice on dis-  
posal.  
If the drain plug is tightened excessively, it  
can be damaged and as a result, fuel will  
leak.  
•
NDI916Z  
Do not use tools to tighten the drain plug.  
•
Except for models with R9M diesel engine  
5. Bleed air from the fuel system. For details, see  
“Bleeding the fuel system” later in this section.  
The regulations concerning the pollution of the  
environment will vary from country to country.  
Drain the water from the fuel filter:  
–
–
Every time you perform an engine oil change.  
6. Start the engine and make sure there is no fuel  
leakage. Correct as required.  
When the water in fuel filter warning light  
(orange) comes on or flashes irregularly.  
For models with R9M diesel engine  
•
Except for models with R9M diesel engine.  
Proceed as follows:  
Contact a NISSAN dealer or qualified workshop.  
•
1. Connect a suitable drain hose j1 to the drain  
plug j2 .  
2. Place a drain pan j3 under the hose j1 .  
3. Loosen manually the drain plug j2 with 4 to 5  
turns and operate the priming pump j4 to drain  
the water out of the fuel filter.  
CAUTION  
The water from the fuel filter is drained  
with fuel. Prepare a larger capacity pan  
than the volume of the fuel filter.  
•
Maintenance and do-it-yourself 8-13  
Downloaded from manuals search engine  

Related Topics

Popular Owner Manuals