2006-2014 Nissan Qashqai SUV Maintenance and do-it-yourself -> Engine cooling system User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Maintenance and do-it-yourself -> Engine cooling system for Your Nissan Qashqai SUV First Generation (2006-2014)

ENGINE COOLING SYSTEM  
Improper servicing or engine coolant change  
can result in reduced heater performance and  
engine overheating.  
•
CHECKING ENGINE COOLANT  
LEVEL  
WARNING  
Never remove the engine coolant reservoir  
•
cap when the engine is hot. Serious burns  
could be caused by high pressure fluid es-  
caping from the engine coolant reservoir. Wait  
until the engine and radiator have cooled  
down.  
WARNING  
To avoid the danger of being scalded, never  
change the coolant when the engine is hot.  
•
•
Avoid direct skin contact with used coolant. If  
skin contact is made, wash thoroughly with  
soap or hand cleaner and plenty of water as  
soon as possible.  
Engine coolant is poisonous and should be  
stored carefully in marked containers out of  
the reach of children.  
•
NDI909Z  
The engine cooling system is filled at the factory  
with a high-quality, year-round and extended life en-  
gine coolant. The high quality engine coolant con-  
tains the specific solutions effective for the anti-cor-  
rosion and the anti-freeze function. Therefore, addi-  
tional cooling system additives are not necessary.  
Keep coolant out of reach of children and  
pets.  
•
Check the coolant level in the reservoir when the  
engine is cold. If the coolant level is below MIN j2 ,  
add coolant up to the MAX j1 level.  
NISSAN GREEN PROGRAM  
Engine coolant must be disposed of properly.  
Check your local regulations.  
CAUTION  
CAUTION  
If the cooling system frequently requires coolant,  
have it checked by a NISSAN dealer or qualified  
workshop.  
When adding or replacing engine coolant, be  
sure to use Genuine NISSAN engine coolant  
or equivalent.  
•
CHANGING ENGINE COOLANT  
CAUTION  
The use of other types of engine coolant may  
damage the engine cooling system.  
•
Major cooling system repairs should be per-  
The engine coolant reservoir tank is equipped  
•
•
formed by a NISSAN dealer or qualified work-  
shop. The service procedures can be found in  
the appropriate NISSAN Service Manual.  
with a pressure cap, use a Genuine NISSAN  
cap or its equivalent when replacement is re-  
quired.  
NDI910Z  
When checking or replacement is required,  
NISSAN recommends contacting a NISSAN  
dealer or qualified workshop for servicing.  
•
8-6 Maintenance and do-it-yourself  
Downloaded from manuals search engine  
13. Stop the engine and check coolant level, allow  
to cool and refill up to the MAX level.  
6. Install the hose and securely tighten the engine  
block drain plug.  
HR16DE, MR20DE, M9R or R9M  
engine  
14. Check radiator lower hose for any signs of leak-  
age.  
7. Fill the reservoir up to the MAX level with cool-  
ant. See “Capacities and recommended  
fuel/lubricants” in the “9. Technical information”  
section for cooling system capacity.  
1. Set the heater or air conditioner temperature  
control to the maximum “HOT” position.  
15. Close the bonnet.  
2. Open the bonnet. For details, see “Bonnet  
release” in the “3. Pre-driving checks and  
adjustments” section.  
8. Install the engine coolant reservoir cap.  
9. Start the engine, and rev the engine two or three  
times under no load.  
3. Open the engine coolant reservoir cap j1 to  
help to drain the coolant.  
10. Touch the radiator hose and feel if the water  
flows.  
4. Disconnect the end of the hose j2 to drain the  
coolant.  
11. Keep racing the engine at a speed of 2,000 –  
2,500 rpm for about 10 minutes.  
5. Flush the cooling system by running clean water  
through the engine coolant reservoir.  
NDI941Z  
12. Observe the coolant temperature gauge for  
signs of overheating.  
6. Install the hose j2 .  
7. Fill the coolant reservoir up to the MAX level.  
K9K engine  
13. Stop the engine and check coolant level, allow  
to cool and refill up to the MAX level.  
See  
“Capacities  
and  
recommended  
fuel/lubricants” in the “9. Technical information”  
section for cooling system capacity.  
1. Set the heater or air conditioner temperature  
control to the maximum “HOT” position.  
14. Check the radiator lower hose for any signs of  
leakage.  
8. Install the engine coolant reservoir cap.  
2. Open the bonnet. For details, see “Bonnet  
release” in the “3. Pre-driving checks and  
adjustments” section.  
15. Close the bonnet.  
9. Start the engine, and rev the engine two or three  
times under no load.  
3. Disconnect the radiator lower hose j1 and open  
the drain plug j2 on the engine block.  
10. Touch the radiator hose and feel if the water  
flows.  
4. Open the engine coolant reservoir cap to help to  
drain the coolant.  
11. Keep racing the engine at a speed of 3,000 rpm  
for about 10 minutes.  
5. Flush the cooling system by running fresh water  
through the engine coolant reservoir.  
12. Observe the coolant temperature gauge for  
signs of overheating.  
Maintenance and do-it-yourself 8-7  
Downloaded from manuals search engine  

Related Topics

Popular Owner Manuals