Get Getting to know your vehicle -> Exterior lighting and signals Guide for Renault Zoe 4 Door Third Generation (2019-2024)

EXTERIOR LIGHTING AND SIGNALS (1/6)

Dipped beam

headlights

k

2

1

Manual operation

1

Turn the ring 2 until the symbol is oppo-

site mark 3. This indicator light on the

instrument panel comes on.

Automatic operation

(depending on vehicle)

Turn ring 2 until the AUTO symbol is op-

posite mark 3: with the engine running,

the dipped beam headlights switch on

or off automatically depending on the

brightness of the light outside, without

any action on stalk 1.

3

Daytime running lights

Your vehicle is fitted with daytime light-

ing (depending on the version).

Side lights

Turn the ring 2 until the symbol

is opposite mark 3. This indicator light



on the instrument panel comes on.

The daytime running lights come on

automatically with no action on stalk 1

when the engine is started, and they go

off once the engine is switched off. This

must be in AUTO mode.

If driving on the left in a left-hand

drive vehicle (or vice versa), drivers

must have the lights adjusted by an

authorised dealer for the duration of

the trip.

Before driving at night, check that the electrical equipment is operating

correctly and adjust the headlight beams (if your vehicle is not carrying

its normal load). As a general precaution, check that the lights are not ob-

scured (by dirt, mud, snow or objects being transported).

1.99

EXTERIOR LIGHTING AND SIGNALS (2/6)

Automatic main beam

The main beam headlights come on au-

tomatically if:

– exterior light is weak;



2

1

headlights

Depending on the vehicle, this system

switches the main beam headlights on

and off automatically. It uses a camera

located behind the interior rear-view

mirror to detect vehicles that are being

followed and those coming in the oppo-

site direction.

– no other vehicles or lighting are de-

tected;

– the vehicle speed is above approxi-

mately 25 mph (40 km/h).

If any of the above conditions are not

fulfilled, the system switches to dipped

beam headlights.

3

Note: make sure the windscreen is not

obscured (dirt, mud, snow, condensa-

tion etc.).

To activate automatic main beam

headlights:

Main beam headlights

With the engine running and

the dipped beam headlights lit, push

stalk 1. This indicator light on the instru-

ment panel comes on.

á

Turn ring 2 until the AUTO symbol is op-

posite mark 3 and push the stalk 1.

Warning light

strument panel.



comes on the in-

The system may encounter difficul-

ties under certain conditions, inclu-

ding:

– extreme weather conditions (rain,

snow, fog, etc.);

To return to the dipped headlight posi-

tion, pull the stalk 1 towards you again.

– obstruction in front of the wind-

screen or camera;

– when a following or oncoming ve-

hicle has weak or hidden lighting;

– incorrect settings for the front

headlights;

– reflective systems;

– ...

1.100

EXTERIOR LIGHTING AND SIGNALS (3/6)

Operating faults

2

1

When the message “Check Automatic

Lighting” appears on the instrument

panel, the system is deactivated.

Consult an approved dealer.

3

Using the portable naviga-

tion system at night in the

windscreen area below the

camera may disturb the op-

eration of the “automatic main beam

headlights” system (risk of reflection

on the windscreen).

Automatic main beam

headlights (continued)



To deactivate automatic main beam

headlights:

– turn ring 2 to a position other than

AUTO;

or

The “automatic main beam

headlights” system should

– pull the stalk 1.

under no circumstances be

used to replace driver atten-

tion and responsibility with regard

to vehicle lighting and adapting to

light, visibility and traffic conditions.

Warning light

strument panel.



goes out on the in-

1.101

EXTERIOR LIGHTING AND SIGNALS (4/6)

Lights-on reminder buzzer

Welcome and goodbye

function

(depending on the vehicle)

If the lights are on after the engine is

switched off, a warning beep sounds

when the driver’s door is opened to

warn you that the lights are still on.

2

1

Once the function is activated, the day-

time running lights and the rear side

lights will light up automatically upon

detection of the card or when the vehi-

cle is unlocked.

Operating faults

If the “Check lighting” message ap-

^{pears with the}© warning light and

They switch off automatically:

– approximately one minute after light-

ing up;

the

k

warning light flashes on the

instrument panel, this indicates a light-

ing fault.

– when starting the engine based on

the position of the lighting stalk;

Consult an authorised dealer.

or

Switching off the lights

– upon locking the vehicle.

The lights will go out automatically

when the engine is switched off, the

driver's door is opened or the vehicle

is locked. In this case, the next time

the engine is started the lights will be

switched back on according to the posi-

tion of the ring 2.

Activating/deactivating the

function

With the vehicle stationary, engine run-

ning, from the multimedia screen select

the “Settings” menu, “Vehicle” tab, the

“Car configuration” menu, “Welcome”

then “External welcome”. Choose “ON”

or “OFF” to activate or deactivate the

function.

Note: if the fog lights are lit, the lights

are not switched off automatically.

1.102

EXTERIOR LIGHTING AND SIGNALS (5/6)

With the engine lights switched off,

the 2 ring in AUTO, pull the lever 1 to-

wards you: the side lights and dipped

beam headlights will switch on for ap-

proximately 30 seconds along with the

2

1

š

and

k

on the instrument

panel.

To increase this duration, you may pull

the stalk up to four times (total time re-

stricted to approximately two minutes).

On the instrument panel, the message

“lighting on _ _ _” followed by the re-

maining time will appear as confirma-

tion. You can then lock your vehicle.

To switch off the lights before they go

out automatically, turn ring 2 to any po-

sition, then return it to position AUTO.

“See-me-home lighting”

function

This function enables you to briefly

switch on the side lights and dipped

beam headlights (e.g. to provide light

when opening a gate).

1.103

EXTERIOR LIGHTING AND SIGNALS (6/6)

Rear fog light

Switching off the lights



Turn centre ring 4 on the stalk

until the symbol faces mark 3, then re-

Turn the centre ring 4 again until mark 3

is opposite the symbol for the fog lights

that you wish to switch off. The corre-

sponding indicator light on the instru-

ment panel goes out.

2 3

4

1

lease it.

Operation of the fog lights depends on

the exterior lighting selected, and an in-

dicator light will light up on the instru-

ment panel.

The front and rear fog lights switch off

when the exterior lights are switched

off.

To avoid inconveniencing other road

users, remember to switch off the rear

fog light when it is no longer needed.

Cornering lights

(depending on vehicle)

Driving in forward gear, whenever the

dipped beam headlights are on and

under certain conditions (at speed, the

steering wheel at an angle, the indica-

tor lights on, etc.), when taking a corner

one of the front fog lights will switch on

to light the inside of the bend.

Front fog lights

Turn centre ring 4 on the

stalk 1 until the symbol faces mark 3,

then release it.

g

Operation of the fog lights depends on

the exterior lighting position selected,

and an indicator light will light up on the

instrument panel.

In reverse, the two front fog lights

switch on automatically.

When driving in fog or snow, or

when transporting objects which are

higher than the roof, the headlights

do not come on automatically.

The driver remains in full control of

switching on the fog lights: the indi-

cator lights on the instrument panel

inform you whether the fog lights

are lit (indicator light on) or not (indi-

cator light off).

1.104

Getting to know your vehicle -> Exterior lighting and signals for Your Renault Zoe 4 Door Third Generation (2019-2024)

Related Topics

Popular Owner Manuals

Latest Owner Manuals