Get Instruments and controls -> Clock Guide for Subaru XV SUV First Generation (2010-2016)

3-27

Instruments and controls/Information display

& Clock

! Turn off display of driving informa-

tion display

The driving information display can be

turned off.

To turn off the display, turn the ignition

switch to the “LOCK” (off) position and

press the “+” button adjacent to the clock

display for approximately 5 seconds.

Then, the driving information display and

the clock display will blink for 3 seconds to

notify you that the driving information

display has been turned off.

To restore the driving information display,

Trip knob

once again press the “+” button for

approximately 5 seconds.

Pressing the trip knob toggles the display

To adjust the time shown by the clock,

between the average vehicle speed cor-

press the “+” button or “−” button. If you

NOTE

responding to the A trip meter display and

press the “+” button, the indicated time will

. The initial display setting of the

the average vehicle speed corresponding

change in one-minute increments. If you

driving information display has been

to the B trip meter display.

press the “−” button, the indicated time will

set to operational at the time of ship-

change in one-minute decrements. If you

When either of the trip meter displays is

ment from the factory.

keep the button pressed, the rate at which

reset, the corresponding average vehicle

. The average fuel consumption and

the indicated time changes will speed up.

speed value is also reset.

average vehicle speed are calculated

The clock can be set to 12-hour or 24-hour

NOTE

even while the driving information dis-

clock displays. Perform the following

play is not displayed.

When either trip meter display is reset,

procedure to switch the display format.

. Even if you turn off the driving

the average vehicle speed correspond-

1. Place the ignition switch in the “LOCK”

information display, the display will

ing to that trip meter display is not

(off) position.

automatically turn on when the battery

shown until the vehicle has subse-

voltage is disconnected and then re-

2. Press and hold the “−” button that is

quently covered a distance of 1 mile

connected for battery replacement or

located near the clock display for approxi-

(or 1 km).

fuse replacement.

mately 5 seconds. The clock display will

then start to flash.

– CONTINUED –

$3-28 Instruments and controls/Multi function display3. While the clock display is flashing,& Safety precautionsMulti function displaypress and hold the “+” button for approxi-mately 2 seconds. The clock format will& Models without multi func-WARNINGthen displayAlways pay adequate attention to4. The clock display will continue to flashNOTEsafe driving when operating thefor approximately 3 seconds to inform you. For models with information displaymulti function display while thethat the clock display has been changed.(black and white), refer to “Informationvehicle is in motion. When operationIf you want to change the clock displaydisplay” the multi-function display is dis-again, press and hold the “+” button for. When the vehicle is in motion,turbing your awareness and abilityapproximately 2 seconds while the clockcertain functions and selections mayto concentrate on driving, stop thedisplay is be in a safe place before per-forming operations on the U.S.-spec models are not equippedAlso, do not concentrate on thewith the multi function display. The otherdisplay while driving. Doing so maymodels may be equipped with the multicause you to look away from thefunction display or not, depending on theroad and could result in an .$

3-28 Instruments and controls/Multi function display

3. While the clock display is flashing,

& Safety precautions

Multi function display

press and hold the “+” button for approxi-

mately 2 seconds. The clock format will

& Models without multi func-

WARNING

then change.

tion display

Always pay adequate attention to

4. The clock display will continue to flash

NOTE

safe driving when operating the

for approximately 3 seconds to inform you

. For models with information display

multi function display while the

that the clock display has been changed.

(black and white), refer to “Information

vehicle is in motion. When operation

If you want to change the clock display

display” F3-23.

of the multi-function display is dis-

again, press and hold the “+” button for

. When the vehicle is in motion,

turbing your awareness and ability

approximately 2 seconds while the clock

certain functions and selections may

to concentrate on driving, stop the

display is flashing.

not be available.

vehicle in a safe place before per-

forming operations on the screen.

The U.S.-spec models are not equipped

Also, do not concentrate on the

with the multi function display. The other

display while driving. Doing so may

models may be equipped with the multi

cause you to look away from the

function display or not, depending on the

road and could result in an accident.

model.

Instruments and controls -> Clock for Your Subaru XV SUV First Generation (2010-2016)

Related Topics

Popular Owner Manuals

Latest Owner Manuals