2010-2016 Subaru XV SUV Instruments and controls -> Multi function display User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Instruments and controls -> Multi function display for Your Subaru XV SUV First Generation (2010-2016)

3-28
Instruments and controls/Multi function display
3. While the clock display is flashing,
press and hold the “+” button for approxi-
mately 2 seconds. The clock format will
then change.
4. The clock display will continue to flash
for approximately 3 seconds to inform you
that the clock display has been changed.
If you want to change the clock display
again, press and hold the “+” button for
approximately 2 seconds while the clock
display is flashing.
Multi function display
& Models without multi func-
tion display
NOTE
. For models with information display
(black and white), refer to “Information
display” F3-23.
. When the vehicle is in motion,
certain functions and selections may
not be available.
The U.S.-spec models are not equipped
with the multi function display. The other
models may be equipped with the multi
function display or not, depending on the
model.
& Safety precautions
WARNING
Always pay adequate attention to
safe driving when operating the
multi function display while the
vehicle is in motion. When operation
of the multi-function display is dis-
turbing your awareness and ability
to concentrate on driving, stop the
vehicle in a safe place before per-
forming operations on the screen.
Also, do not concentrate on the
display while driving. Doing so may
cause you to look away from the
road and could result in an accident.
& Features
The multi function display has the follow-
ing functions.
Description Page
Displays useful messages, such
as warning information, etc.
3-31
Displays basic screens (e.g. fuel
consumption screen, etc.)
3-32
Sets and adjusts maintenance
notification
3-57
Registers driving history 3-61
Sets and customizes car opera-
tion
3-62
Also, the multi function display can also be
used to set and initialize the multi function
display itself.
& Locations
Multi function display
1) Outside temperature indicator
2) Information reminder
3) Top display (For the display setting, refer
to “Top display setting” F3-50.)
4) Clock
5) Driving information display (For the dis-
played contents, refer to “Basic screens”
F3-32.)
& Basic operation
Control switch
1) Up (select)
2) Set (enter)
3) Down (select)
By operating “
” or “ ” of the control
switch, the screens and selection items
can be switched. When the “
/SET”
switch is pulled toward you, the item can
be selected and set.
& Welcome screen
When the door is unlocked and the
driver’s door is opened, the welcome
screen will appear for a short time.
Instruments and controls/Multi function display
3-29
– CONTINUED –
3-30
Instruments and controls/Multi function display
NOTE
. The welcome screen will disappear
when the ignition switch is turned to
the “ON” position while the welcome
screen is displayed.
. If any of the doors (including the
rear gate) is opened while the welcome
screen is displayed, the door ajar
warning will appear.
. The welcome screen can be set to
on or off. For details, refer to “Bypass
screen setting” F3-55.
. For a certain period of time after the
welcome screen has once appeared, it
may not appear again even when the
driver’s door is opened again. This
does not indicate a malfunction.
& Ending screen
When the ignition switch is turned to the
“LOCK” (off) posit ion, the “Goodbye”
screen will appear for several seconds.
& Self-check screen
When the ignition switch is turned to the
“ON” position, the vehicle self-check is
performed. The screens corresponding to
the following items will appear one after
another for several seconds each.
1) Windshield washer fluid: Checks the
level of windshield washer fluid.
2) Brake fluid: Checks the level of brake
fluid.
3) Engine oil: Checks the interval of engine
oil replacement.
4) Oil filter: Checks the interval of oil filter
replacement.
5) Tires: Checks the interval of tire rotation.
6) Inspection and maintenance: Checks the
interval of inspection and maintenance.
When the checks are performed, the color
of the icon corresponding to the checked
item will turn green.
If there is no warning message, the self-
check is complete without notification.
Example of notification
If there is a warning messag e or a
maintenance notification, the color of the
icon corresponding to the item will turn
yellow and the warning message or the
maintenance notification will be displayed.
Take the appropriate actions based on the
messages indicated.
NOTE
. The self-check screen can be set to
on or off. For details, refer to “On/Off
setting” F3-59.
. After performing the maintenance,
change the setting of the correspond-
ing maintenance item. For details, refer
to “Maintenance settings” F3-57.
. The maintenance notification screen
will be displayed under either of the
following conditions.
– The period of time remaining
until the registered notification date
is 15 days or less.
– The total driving distance remain-
ing until the registered notification
distance is approximately 311 miles
(500 km) or less.
. The maintenance notification screen
will be displayed until either of the
following conditions is satisfied.
– The period of time passed after
the registered notification date is 15
days or more.
– The total distance driven after the
registered notification distance is
approximately 311 miles (500 km) or
more.
& Interruption screen
Warning information (display example)
Useful messages, such as reminder in-
formation, vehicle information, warning
information, etc. may interrupt the current
screen and appear on the display accom-
panied by a beep. Take proper action
according to the message.
The warning screen will return to the
original screen after a few seconds. If
the warning screen can be displayed
again, an information reminder “
” will
appear on the upper lef t par t of t he
display. To recall the message marked
with “
” on the display, pull the “ /SET”
switch on the steering wheel toward you.
Instruments and controls/Multi function display
3-31
– CONTINUED –
3-32
Instruments and controls/Multi function display
& Basic screens
! Basic screen items
These are the basic screens of the multi
function display.
Item Page
Information bar 3-32
Fuel consumption screen 3-33
ECO gauge screen 3-34
ECO history screen 3-34
Vehicle activation status
screen
3-35
Triple meter screen 3-36
Guidance screen 3-37
Clock/calendar screen
3-37
By operating the “
” or “ ” switch on the
steering wheel, you can switch the screen
that is always displayed. Also, when the
“
/SET” switch is pulled and held, the
selection screen can be displayed. For
details about the selection screen, refer to
“Selection screen” F 3-38.
! Information bar
1) Information bar
2) Outside temperature indicator
3) Information reminder
4) Top display
5) Clock
While the ignition switch is in the “ACC” or
“ON” position, the outside temperature
indicator, clock, etc. will be shown on the
information bar.
! Outside temperature indicator
This displays the outside temperature
between − 408 F (− 408C) and 1228F
(508C).
Icy road surface warning screen
When the outside temperature becomes
378F (38C) or less, the icy road surface
warning screen interrupts to inform the
driver that the road surface may be frozen.
NOTE
. The outside temperature indicator
shows the temperature around the
sensor. Therefore, the temperature in-
dication may differ from the actual
outside air temperature.
. The icy road surface warning screen
should be treated only as a guide. Be
sure to check the condition of the road
surface before driving.
. Once the icy road surface warning
screen is displayed, it will not be
displayed a gain unless the outside
temperature increases to 418F (58C) or
higher.
! Information reminder
The screen returns to the original screen
several seconds after the interruption
screen has been displayed. If the inter-
ruption screen can be displayed once
more even after the original screen has
appeared, an information reminder should
be displayed. For details about the inter-
ruption screen, refer to “Interruption
screen” F3-31.
! Top display
One of the following items can be dis-
played on the top display.
. Average fuel consumption correspond-
ing to the driving distance of each trip
meter
. Current fuel consumption (This may
not be displayed when driving at a low
speed.)
. Driving range on remaining fuel
For details about the setting of the top
display, refer to “Top display setting” F3-
50.
NOTE
The driving range on the remaining fuel
is calculated using the average fuel
consumption of the last 19 miles (30
km) driven. This value may be different
from the values calculated using the
average fuel consumption correspond-
ing to the driving distance of each trip
meter or the current fuel consumption.
! Clock
The clock can be displayed in either 12-
hour display or 24-hour display. For details
about the setting, refer to “Current date
and time setting” F3-40.
NOTE
If the vehicle battery is disconnected,
the clock shown in the information bar
will be reset. Set the time again after
the vehicle battery is connected. For
details about the setting, refer to “Top
display setting” F3-50.
! Fuel consumption screen
1) Average fuel consumption corresponding
to the driving distance of each trip meter
2) Current fuel consumption
3) Driving range on remaining fuel
The di splayed location can be custo-
mized. For details, refer to “Fuel consump-
tion screen setting” F3-51.
Instruments and controls/Multi function display
3-33
– CONTINUED –
3-34
Instruments and controls/Multi function display
! ECO gauge screen
1) Average fuel consumption corresponding
to the driving distance of each trip meter
2) ECO gauge
The gauge pointer shows the difference
between the current fuel consumption and
the average fuel consumption that is
displayed on the center part of the screen.
If the gauge pointer moves toward the
green side, this indicates better fuel
efficiency.
! ECO history screen
1) Average fuel consumption per unit time
(bar graph)
2) Average fuel consumption corresponding
to the driving distance of each trip meter
(red line)
This screen displays the fuel economy
history for the vehicle using a bar graph.
The horizontal scale represents the past
time range and the vertical scale repre-
sents the fuel consumption. The green
bars show driving with good fuel economy
and the yellow bars show driving with poor
fuel economy.
The time range of the history can be set.
The width of the bar graph is adjusted as
follows depending on the set time range.
Time range Width of bar graph
30 minutes 1 minute
60 minutes 2 minutes
120 minutes
4 minutes
For details about the setting, refer to
“Economy history setting” F3-52.
! Vehicle activation status screen
When the vehicle stops
1) Steering axle
When the vehicle is being driven regularly
1) Power train (illuminated in blue)
When the Vehicle Dynamics Control sys-
tem is being activated: the tires illuminate
in yellow.
1) History of Vehicle Dynamics Control
system activation
When the Vehicle Dynamics Control sys-
tem has been activated: the tires remain
illuminated in y ellow while the Vehicle
Dynamics Control System is activated.
1) Activation status of the ABS (Anti-lock
Brake System)
2) Vehicle Dynamics Control system oper-
ating indicator (flashing in yellow)
3) History of Vehicle Dynamics Control
system activation
This screen displays the following vehicle
information.
. steering angle and driving wheel status
. activation status of the ABS (Anti-lock
Brake System)
. activation status of the Vehicle Dy-
namics Control system
Wh ile driving, t he vehicle wheels are
illuminated in blue and the driving direc-
Instruments and controls/Multi function display
3-35
– CONTINUED –
3-36
Instruments and controls/Multi function display
tion is represented using an animation of
the traffic lane.
If the ABS is activated, all of the vehicle’s
wheels will be illuminated in yellow and
the length of operation in seconds and the
number of activations will be displayed in
the bar indicator, located on the lowermost
part of the display.
If the Vehicle Dynamics Control system is
activated, the activated vehicle wheels will
be illuminated in yellow and the operating
indicator “
” will appear on the upper right
part of the display. Also, the length of
operation in seconds and the number of
activations will be displayed in the bar
indicator.
! Triple meter screen
Triple meter screen (display example)
This screen displays up to three optional
pieces of information that can be selected
from the following items.
The items shown in the triple meter screen
can be changed. For details, refer to
“Triple meter setting” F3-53.
Item Details
Average vehicle speed (Average
vehicle speed for the entire driving
time from when the trip meter was
reset)
Lifetime fuel consumption
Engine oil temperature
Accelerator opening ratio
Journey time (the time that has
elapsed since the ignition switch
was turned to the “ON” position)
Journey distance (the distance
that has been driven since the
ignition switch was turned to the
“ON” position)
Average fuel consumption for the
entire driving distance from when
the ignition switch was turned to
the “ON” position
! Guidance screen
When the “ /SET” switch is pulled and
held, the selection screen can be dis-
played.
The displayed contents can be set or
customized from the selection screen. For
details, refer to “Selection screen” F3-38.
! Clock/calendar screen
Clock (analog format)
Clock (digital format)
Calendar
1) Today’s date
2) Birthday/Anniversary
In addition to the clock/calendar, the out-
side temperature and average fuel con-
sumption can also be displayed.
You can select clock (analog format),
clock (digi tal for mat) or calendar. The
clock/calendar can also be set so that it
is not displayed. For details, refer to
“Clock screen setting” F3-54.
Instruments and controls/Multi function display
3-37
– CONTINUED –
3-38
Instruments and controls/Multi function display
& Selection screen
When the “
/SET” switch is pulled and held, the setting screen for each menu can be displayed. Select the preferred menu by
operating the “
” or “ ” switch.
Top menu Menu option Description Page
Date
Date Set and adjust the time and date. 12h or 24h format can be selected. 3-40
Birthday Set a birthday. 3-41
Anniversary Set an anniversary day. 3-43
Daylight Saving Time Turn the daylight saving time on or off 3-46
Go Back Return to the top menu. —
Display
Brightness Adjust the brightness. +5 ↔ −5 3-47
Contrast Adjust the contrast. +5 ↔ −5 3-48
Screen Off Turn the screen on or off. On or Off 3-48
Beep Adjust the beep sound volume. High, Low or Off 3-49
Go Back Return to the top menu. —
Screen Setting
Top Display
Set and customize the top display informa-
tion contents.
Avg Cons, Inst Cons, Range
or Off
3-50
Cons Customize the fuel consumption information display. 3-51
Eco History
Set and customize the time of logging fuel
consumption history.
30 min, 60 min or 120 min 3-52
Triple Meter Set and customize the triple meter. 3-53
Clock Select the clock format.
Analog, Digital, Calendar or
Off
3-54
Bypass Screen Set the bypass screen for each item. On or Off 3-55
Languages Select the display language. English or French 3-56
Go Back Return to the top menu. —
Top menu Menu option Description Page
Maintenance
Engine Oil Set and adjust the oil maintenance notification date. 3-58
Oil Filter Set and adjust the oil filter maintenance notification date. 3-59
Tires Set and adjust the tire maintenance notification date. 3-59
Maintenance Schedule Set and adjust the vehicle maintenance notification date. 3-59
On/Off
Turn on or off the self-check screen that is
activated when the ignition switch is turned
to the “ON” position.
On or Off 3-59
Clear All Settings Clear all settings for maintenance items. Yes or No 3-60
Go Back Return to the top menu. —
Driving History
Set Register and overwrite the driving record. 3-61
Go Back Return to the top menu. —
Car Setting
Audible Signal Set the audible signal. On or Off 3-62
Hazard Warning Flasher Set the hazard warning flasher. On or Off 3-64
Defogger
Set and customize the operation of the
defogger.
15 minutes or Continuous 3-65
Interior Light
Set and customize the interior light off delay
timer.
10, 20, 30 seconds or Off 3-66
Auto Light Sensor
(models with auto on/off head-
lights)
Set and customize the sensitivity of the auto
light sensor.
Low, Mid, High or Max 3-67
Go Back Return to top menu. —
Initialize
Reset to Defaults Reset all settings to the default settings. Yes or No 3-68
Lifetime Fuel Consumption Reset Clear logged lifetime fuel consumption data. Yes or No 3-69
Go Back Return to the top menu. —
Go Back
— Return to the top menu.
—
Instruments and controls/Multi function display
3-39
– CONTINUED –
3-40
Instruments and controls/Multi function display
& Date and time settings
The items in the date and time settings
can be set. To change the items, operate
the “
” or “ ” switch.
NOTE
. The “Date” item must be set to
display the “Birthday ”, “Anniversary”
and notifications for vehicle mainte-
nance.
. The “Birthday” and “Anniversary”
items can be entered after the “Date”
item has been set.
. Dates that do not exist in the
Gregorian calendar cannot be set (for
example, April 31).
. If your vehicle is equipped with the
genuine SUBARU navigation system,
the clock of navigation system must be
set separately.
! Preparation for date setting
1. Turn the ignition switch to the “ON”
position.
2. Pull and hold the “
/SET” switch
toward you to show the selection screen.
3. After the selection screen is displayed,
operate the “
” or “ ” switch to show the
“Date” item. Then, pull the “
/SET” switch
toward you.
! Current date and time setting
1. Perform the preparation steps accord-
ing to “Preparation for date setting” F3-
40.
2. Operate the “ ” or “ ” switch to
select the “ Date ” item. Then pull the “
/
SET” switch toward you.
3. Select the item to set by operating the
“
” or “ ” switch. Then pull the “ /SET”
switch toward you.
4. Select a number by operating the “ ”
or “
” switch. Then pull the “ /SET”
switch toward you. When “12 h” is
selected, the clock will be set to a 12-
hour display. When “24 h” is selected, the
clock will be set to a 24-hour display.
5. After entering the date and time, select
“Set” by operating the “
” switch and
confirm the setting by pulling the “
/SET”
switch toward you.
6. The system will notify you that the
setting is complete.
! Birthday setting
1. Perform the preparation steps accord-
ing to “Preparation for date setting” F3-
40.
2. Operate the “ ” or “ ” switch to
select the “Birthday” item. Then pull the
“
/SET” switch toward you.
3. Select the item to set by operating the
“
” or “ ” switch. Then pull the “ /SET”
switch toward you.
Instruments and controls/Multi function display
3-41
– CONTINUED –
3-42
Instruments and controls/Multi function display
4. The selected item will be shown.
– Pull the “
/SET” switch toward you
to set the selected item.
– If you want to select the other item,
operate the “
” switch to go back to
step 3.
5. Select numbers by operating the “ ”
or “
” switch. Then pull the “ /SET”
switch toward you.
6. After entering the date by repeating
step 5, you can enter the name.
7. Select characters by operating the
“
” or “ ” switch. Then pull the “ /
SET” switch toward you.
– You can select characters of the
English alphabet (upper case charac-
ters and lower case characters are
available), eleven symbols or blank
spaces.
– The word being edite d will be
displayed with an underline.
8. After entering the name by repeating
step 7, select “Set” by operating the “
”
switch and confirm the setting by pulling
the “
/SET” switch toward you.
9. The system will notify you that the
setting is complete.
! If a birthday is approaching
If a birthday is approaching, the following
screen will be displayed accompanied by
a beep when the ignition switch has been
turned to the “ON” position. This function
can be set on or off. For details, refer to
“Bypass screen setting” F3-55.
From 1 to 7 days prior to the birthday
On a birthday (displayed in red)
NOTE
If “_ _” is selected for either the
“M onth” or “Day” item instead of
numbers, the birthday notification will
be deactivated.
! Anniversary setting
1. Perform the preparation steps accord-
ing to “Preparation for date setting” F3-
40.
Instruments and controls/Multi function display
3-43
– CONTINUED –
3-44
Instruments and controls/Multi function display
2. Operate the “ ” or “ ” switch to
select the “Anniversary” item. Then pull
the “
/SET” switch toward you.
3. Select the item to set by operating the
“
” or “ ” switch. Then pull the “ /SET”
switch toward you.
4. The selected item will be shown.
– Pull the “
/SET” switch toward you
to set the selected item.
– If you want to select another item,
operate the “
” switch to go back to
step 3.
5. Select numbers by operating the “ ”
or “
” switch. Then pull the “ /SET”
switch toward you.
6. After entering the date by repeating
step 5, you can enter the name.
7. Select characters by operating the
“
” or “ ” switch. Then pull the “ /
SET” switch toward you.
– You can select characters of the
English alphabet (upper case charac-
ters and lower case characters are
available), eleven symbols or blank
spaces.
– The word being edit ed will be
displayed with an underline.
8. After entering the name by repeating
step 7, select “Set” by operating the “
”
switch and confirm the setting by pulling
the “
/SET” switch toward you.
9. The system will notify you that the
setting is complete.
! If an anniversary is approaching
If an anniversary is approaching, the
following screen will be displayed accom-
panied by a beep when the ignition switch
has been turned to the “ON” position. This
function can be set on or off. For details,
refer to “Bypass screen setting” F3-55.
From 1 to 7 days prior to the anniversary
Instruments and controls/Multi function display
3-45
– CONTINUED –
3-46
Instruments and controls/Multi function display
On an anniversary (displayed in orange)
NOTE
If “_ _” is selected for either the
“M onth” or “Day” item instead of
numbers, the anniversary notification
will be deactivated.
! Clearing birthday or anniversary
1. Perform the preparation steps accord-
ing to “Preparation for date setting” F3-40
and display “Birthday” or “Anniversary” on
the screen.
2. When “_ _” is selected for either the
“Month” or “Day” item instead of numbers,
the setting of “Birthday” or “Anniversary”
will be cleared.
! Daylight saving time setting
1. Perform the preparation steps accord-
ing to “Preparation for date setting” F3-
40.
2. Operate the “ ” or “ ” switch to
select the “Daylight Saving Time” item.
Then pull the “
/SET” switch toward you.
3. The current setting will be displayed.
Pull the “
/SET” switch toward you to
enter the selection mode.
4. Select “On” or “Off” by operating the
“
” or “ ” switch. Then pull the “ /SET”
switch toward you.
5. Select “Set” by operating the “ ”
switch, and confirm the setting by pulling
the “
/SET” switch toward you.
6. The system will notify you that the
setting is complete.
& Image quality and volume
settings
The items in the image quality and volume
settings can be set. To change the items,
operate the “
” or “ ” switch.
! Preparation for image quality and
volume settings
1. Turn the ignition switch to the “ON”
position.
2. Pull and hold the “
/SET” switch
toward you to show the selection screen.
3. After the selection screen is displayed,
operate the “
” or “ ” switch to show the
“Display” item. Then, pull the “
/SET”
switch toward you.
! Brightness setting
1. Perform the preparation steps accord-
ing to “Preparation for image quality and
volume settings” F3-47.
2. Operate the “ ” or “ ” switch to
select the “Brightness” item. Then pull the
“
/SET” switch toward you.
Instruments and controls/Multi function display
3-47
– CONTINUED –
3-48
Instruments and controls/Multi function display
3. Select a brightness level by operating
the “
” or “ ” switch, and confirm the
settin g by pulli ng the “
/SET” switch
toward you.
! Contrast setting
1. Perform the preparation steps accord-
ing to “Preparation for image quality and
volume settings” F3-47.
2. Operate the “ ” or “ ” switch to
select the “Contrast” item. Then pull the
“
/SET” switch toward you.
3. Select a contrast level by operating the
“
” or “ ” switch, and confirm the setting
by pulling the “
/SET” switch toward you.
! Screen OFF setting
1. Perform the preparation steps accord-
ing to “Preparation for image quality and
volume settings” F3-47.
2. Operate the “ ” or “ ” switch to
select the “Screen OFF” item. Then pull
the “
/SET” switch toward you.
3. Pull the “ /SET” switch once more
toward you.
4. The screen is turned off.
Restoring the screen
When the “
”, “ ” or “ /SET” switch is
pulled toward you after the ignition switch
is turned to the “ON” position, the screen
will be restored. The screen will be
restored with the basic screen that was
displayed when the screen was turned off.
While the screen is off, a warning mes-
sage will be displayed if necessary, but
other screens will not be displayed.
! Beep volume setting
1. Perform the preparation steps accord-
ing to “Preparation for image quality and
volume settings” F3-47.
2. Operate the “ ” or “ ” switch to
select the “Beep” item. Then pull the “
/
SET” switch toward you.
3. Pull the “ /SET” switch toward you.
4. Select an item by operating the “ ” or
“
” switch. Then pull the “ /SET” switch
toward you.
Instruments and controls/Multi function display
3-49
– CONTINUED –
3-50
Instruments and controls/Multi function display
5. Select “Set” by operating the “ ”
switch, and confirm the setting by pulling
the “
/SET” switch toward you.
6. The system will notify you that the
setting is complete.
& Screen settings
The items in the screen settings can be
set. To change the items, operate the “
”
or “
” switch, and then pull the “ /SET”
switch toward you.
! Preparation for screen settings
1. Turn the ignition switch to the “ON”
position.
2. Pull and hold the “
/SET” switch
toward you to show the selection screen.
3. After the selection screen is displayed,
operate the “
” or “ ” switch to show the
“Screen Setting” item. Then, pull the “
/
SET” switch toward you.
! Top display setting
1. Perform the preparation steps accord-
ing to “Preparation for screen settings”
F3-50.
2. Operate the “ ” or “ ” switch to
select the “Top Display” item. Then pull the
“
/SET” switch toward you.
3. Pull the “ /SET” switch once more.
4. Select an item by operating the “ ” or
“
” switch. Then pull the “ /SET” switch
toward you.
5. Select “Set” by operating the “ ”
switch, and confirm the setting by pulling
the “
/SET” switch toward you.
6. The system will notify you that the
setting is complete.
! Fuel consumption screen setting
1. Perform the preparation steps accord-
ing to “Preparation for screen settings”
F3-50.
2. Operate the “ ” or “ ” switch to
select the “Cons” item. Then pull the “
/
SET” switch toward you.
3. Pull the “ /SET” switch once more.
Instruments and controls/Multi function display
3-51
– CONTINUED –
3-52
Instruments and controls/Multi function display
4. Select the displayed configuration by
operating the “
” or “ ” switch. Then pull
the “
/SET” switch toward you.
5. Select “Set” by operating the “ ”
switch, and confirm the setting by pulling
the “
/SET” switch toward you.
6. The system will notify you that the
setting is complete.
! Economy history setting
1. Perform the preparation steps accord-
ing to “Preparation for screen settings”
F3-50.
2. Operate the “ ” or “ ” switch to
select the “Eco History” item. Then pull the
“
/SET” switch toward you.
3. Pull the “ /SET” switch once more.
4. Select the time of the logged fuel
consumption his tory by operat ing the
“
” or “ ” switch. Then pull the “ /
SET” switch toward you.
5. Select “Go Back” by operating the “ ”
switch.
6. Select “Set” by operat ing the “ ”
switch and confirm the setting by pulling
the “
/SET” switch toward you.
7. The system will notify you that the
setting is complete.
! Triple meter setting
1. Perform the preparation steps accord-
ing to “Preparation for screen settings”
F3-50.
2. Operate the “ ” or “ ” switch to
select the “Triple Meter” item. Then pull
the “
/SET” switch toward you.
Instruments and controls/Multi function display
3-53
– CONTINUED –
3-54
Instruments and controls/Multi function display
3. Select the setting location (left, center
or right) by operating the “
” or “ ”
switch. Then p ull the “
/SET” switch
toward you.
NOTE
The same item cannot be selected for
the left, center or right location.
4. Select the preferred item by operating
the “
” or “ ” switch. Then pull the “ /
SET” switch toward you.
If you also want to change the setting for
another location, repeat steps 3 and 4.
5. Select “Set” by operat ing the “ ”
switch, and confirm the setting by pulling
the “
/SET” switch toward you.
6. The system will notify you that the
setting is complete.
! Clock screen setting
1. Perform the preparation steps accord-
ing to “Preparation for screen settings”
F3-50.
2. Operate the “ ” or “ ” switch to
select the “Clock” item. Then pull the “
/
SET” switch toward you.
3. Pull the “ /SET ” switch once more.
4. Select “Analog Clock”, “Digital Clock”,
“Calendar” or “Off” by operating the “
” or
“
” switch. Then pull the “ /SET” switch
toward you.
5. Select “Set” by operat ing the “ ”
switch, and confirm the setting by pulling
the “
/SET” switch toward you.
6. The system will notify you that the
setting is complete.
! Bypass screen setting
1. Perform the preparation steps accord-
ing to “Preparation for screen settings”
F3-50.
Instruments and controls/Multi function display
3-55
– CONTINUED –
3-56
Instruments and controls/Multi function display
2. Operate the “ ” or “ ” switch to
select the “Bypass Screen” item. Then pull
the “
/SET” switch toward you.
3. Select the item to set by operating the
“
” or “ ” switch. Then pull the “ /SET”
switch toward you.
4. Select “On” or “Off” by operating the
“
” or “ ” switch. Then pull the “ /SET”
switch toward you.
If you want to change setting for another
item, repeat steps 3 and 4.
5. Select “Set” by operating the “ ” or
“
” switch, and confirm the setting by
pulling the “
/SET” switch toward you.
6. The system will notify you that the
setting is complete.
! Language setting
1. Perform the preparation steps accord-
ing to “Preparation for screen settings”
F3-50.
2. Operate the “ ” or “ ” switch to
select the “Languages” item. Then pull the
“
/SET” switch toward you.
3. The current language setting will be
displayed. Pull the “
/SET” switch toward
you to enter the language selection mode.
4. Select the preferred language by
operating the “
” or “ ” switch. Then
pull the “
/SET” switch toward you.
5. Select “Set” by operat ing the “ ”
switch, and confirm the setting by pulling
the “
/SET” switch toward you.
6. The system will notify you that the
setting is complete.
& Maintenance settings
The items in the maintenance settings can
be set. To change the items, operate the
“
” or “ ” switch toward you.
! Preparation for maintenance set-
tings
1. Turn the ignition switch to the “ON”
position.
2. Pull and h old the “
/SET” switch
toward you to show the selection screen.
Instruments and controls/Multi function display
3-57
– CONTINUED –
3-58
Instruments and controls/Multi function display
3. After the selection screen is displayed,
operate the “
” or “ ” switch to show the
“Maintenance” item. Then, pull the “
/
SET” switch toward you.
! Engine oil setting
1. Perform the preparation steps accord-
ing to “Preparation for maintenance set-
tings” F3-57.
2. Operate the “ ” or “ ” switch to
select the “Engine Oil” item. Then pull the
“
/SET” switch toward you.
3. Select the setting location (month, day,
year or distance) by operating the “
” or
“
” switch. Then pull the “ /SET” switch
toward you.
4. Select a number by operating the “ ”
or “
” switch. Then pull the “ /SET”
switch toward you.
If you also want to change the setting for
another location, repeat steps 3 and 4.
5. Select “Set” by operating the “ ” or
“
” switch and confirm the setting by
pulling the “
/SET” switch toward you.
6. The system will notify you that the
setting is complete.
NOTE
. The notification will be dis played
with information of both date and
distance or either date or distance in
accordance with the setting
. When “_ _” is selected for either the
“Month”, “Day”, “Year” or “Distance”
item instead of numbers, the set noti-
fication will be deactivated.
. If the notification continues for 15
days or more, the system will display
“_ _” on the screen.
. When the distance announcement
reaches 0 mile (0 km), the display will
show “0000” for the next 311 miles (500
km). After exceeding 311 miles (500
km), “_ _ _ _” will be displayed.
! Oil filter setting
The setting procedure is the same as
“Engine oil setting” F3-58, but select the
“Oil Filter” item in step 2.
! Tires setting
The setting procedure is the same as
“Engine oil setting” F3-58, but select the
“Tires” item in step 2.
! Maintenance schedule setting
The setting procedure is the same as
“Engine oil setting” F3-58, but select the
“Maintenance Schedule” item in step 2.
! On/Off setting
1. Perform the preparation steps accord-
ing to “Preparation for maintenance set-
tings” F3-57.
2. Operate the “ ” or “ ” switch to
select the “On/Off” item. Then pull the “
/
SET” switch toward you.
3. The current setting will be displayed.
Pull the “
/SET” switch toward you to
enter the selection mode.
Instruments and controls/Multi function display
3-59
– CONTINUED –
3-60
Instruments and controls/Multi function display
4. Select “On” or “Off” by operating the
“
” or “ ” switch. Then pull the “ /SET”
switch toward you.
5. Select “Set” by operating the “ ”
switch, and confirm the setting by pulling
the “
/SET” switch toward you.
6. The system will notify you that the
setting is complete.
! Clear setting
1. Perform the preparation steps accord-
ing to “Preparation for maintenance set-
tings” F3-57.
2. Operate the “ ” or “ ” switch to
select the “Clear All Settings” item. Then
pull the “
/SET” switch toward you.
3. The system wil l prompt a Yes/No
dialogue (“No” is selected first). To clear
all maintenance settings, select “Yes” by
operating the “ ” switch.
4. Confirm the setting by pulling the “ /
SET” switch toward you.
5. The system will notify you that the
setting is complete.
& Driving history registration
The items in the driving history can be
registered. To change the items, operate
the “
” or “ ” switch, and then pull the
“
/SET” switch toward you.
1. Turn the ignition switch to the “ON”
position.
2. Pull and hold the “
/SET” switch
toward you to show the selection screen.
3. After the selection screen is displayed,
operate the “
” or “ ” switch to show the
“Driving History” item. Then, pull the “
/
SET” switch toward you.
4. Pull the “ /SET” switch toward you
once more to enter the setting mode.
5. The system will notify you of the place
to be selected for approximately 2 sec-
onds.
Instruments and controls/Multi function display
3-61
– CONTINUED –
3-62
Instruments and controls/Multi function display
6. Select one of the registration lines by
operating the “
” or “ ” switch. Then pull
the “
/SET” switch toward you.
7. To overwrite the previous registration,
pull the “
/SET” switch toward you. When
registration is performed the first time, it is
registered directly without a notification.
8. The system will notify you that the
registration is complete.
NOTE
The driving history can be registered
for the trip meter A or B.
& Car settings
The items in the car settings can be set.
To change the items, operate the “
” or
“
” switch, and then pull the “ /SET”
switch toward you.
! Preparation for car settings
1. Turn the ignition switch to the “ON”
position.
2. Pull and hold the “
/SET” switch
toward you to show the selection screen.
3. After the selection screen is displayed,
operate the “
” or “ ” switch to show the
“Car Setting” item. Then, pull the “
/SET”
switch toward you.
! Audible signal setting
1. Perform the preparation steps accord-
ing to “Preparation for car settings” F3-62.
2. Operate the “ ” or “ ” switch to
select the “Audible Signal” item. Then pull
the “
/SET” switch toward you.
3. The current setting will be displayed.
Pull the “
/SET” switch toward you to
enter the selection mode.
4. Select “On” or “Off” by operating the
“
” or “ ” switch. Then pull the “ /SET”
switch toward you.
5. Select “Set” by operat ing the “ ”
switch, and confirm the setting by pulling
the “
/SET” switch toward you.
6. The system will notify you that the
setting is complete.
If the setting is not available, the following
notification will be displayed. In this case,
perform the setting procedure again.
Instruments and controls/Multi function display
3-63
– CONTINUED –
3-64
Instruments and controls/Multi function display
! Hazard warning flasher setting
1. Perform the preparation steps accord-
ing to “Preparation for car settings” F3-62.
2. Operate the “ ” or “ ” switch to
select the “Hazard Warning Flasher” item.
Then pull the “
/SET” switch toward you.
3. The current setting will be displayed.
Pull the “
/SET” switch toward you to
enter the selection mode.
4. Select “On” or “Off” by operating the
“
” or “ ” switch. Then pull the “ /SET”
switch toward you.
5. Select “Set” by operating the “ ”
switch, and confirm the setting by pulling
the “
/SET” switch toward you.
6. The system will notify you that the
setting is complete.
If the setting is not available, the following
notification will be displayed. For more
details, contact a SUBARU dealer.
! Defogger setting
1. Perform the preparation steps accord-
ing to “Preparation for car settings” F3-62.
2. Operate the “ ” or “ ” switch to
select the “Defogger” item. Then pull the
“
/SET” switch toward you.
3. The current setting will be displayed.
Pull the “
/SET” switch toward you to
enter the selection mode.
4. Select the preferred setting by operat-
ing the “
” or “ ” switch. Then pull the
“
/SET” switch toward you.
5. Select “Set” by operating the “ ”
switch, and confirm the setting by pulling
the “
/SET” switch toward you.
6. The system will notify you that the
setting is complete.
Instruments and controls/Multi function display
3-65
– CONTINUED –
3-66
Instruments and controls/Multi function display
If the setting is not available, the following
notification will be displayed. For more
details, contact a SUBARU dealer.
! Interior light off delay timer setting
1. Perform the preparation steps accord-
ing to “Preparation for car settings” F3-62.
2. Operate the “ ” or “ ” switch to
select the “Interior Light” item. Then pull
the “
/SET” switch toward you.
3. The current setting will be displayed.
Pull the “
/SET” switch toward you to
enter the selection mode.
4. Select the preferred setting by operat-
ing the “
” or “ ” switch. Then pull the
“
/SET” switch toward you.
5. Select “Set” by operating the “ ”
switch, and confirm the setting by pulling
the “
/SET” switch toward you.
6. The system will notify you that the
setting is complete.
If the setting is not available, the following
notification will be displayed. For more
details, contact a SUBARU dealer.
! Auto light sensor sensitivity setting
1. Perform the preparation steps accord-
ing to “Preparation for car settings” F3-62.
2. Operate the “ ” or “ ” switch to
select the “Auto Light Sensor” item. Then
pull the “
/SET” switch toward you.
3. The current setting will be displayed.
Pull the “
/SET” switch toward you to
enter the selection mode.
4. Select the preferred setting by operat-
ing the “
” or “ ” switch. Then pull the
“
/SET” switch toward you.
Instruments and controls/Multi function display
3-67
– CONTINUED –
3-68
Instruments and controls/Multi function display
5. Select “Set” by operating the “ ”
switch, and confirm the setting by pulling
the “
/SET” switch toward you.
6. The system will notify you that the
setting is complete.
If the setting is not available, the following
notification will be displayed. For more
details, contact a SUBARU dealer.
& Initialize
Items that have been set to your pre-
ference can be initialized. To select an
initialization menu, operate the “
” or “ ”
switch as follows.
! Preparation for initialization
1. Turn the ignition switch to the “ON”
position.
2. Pull and hold the “
/SET” switch
toward you to show the selection screen.
3. After the selection screen is displayed,
operate the “
” or “ ” switch to show the
“Initialize” item. Then, pull the “
/SET”
switch toward you.
! Reset to factory default settings
1. Perform the preparation steps accord-
ing to “Preparation for initialization” F3-
68.
2. Operate the “ ” or “ ” switch to
select the “Reset to Defaults” item. Then
pull the “
/SET” switch toward you.
3. The syst em will prompt a Yes/No
dialogue (“No” is selected first). To return
to the factory default settings, select “Yes”
by operating the “
” switch.
4. Confirm the setting by pulling the “ /
SET” switch toward you.
5. The system will notify you that the
setting is complete.
! Lifetime fuel consumption resetting
1. Perform the preparation steps accord-
ing to “Preparation for initialization” F3-
68.
2. Operate the “ ” or “ ” switch to
select the “Lifetime Fuel Consumption
Resetting” item. Then pull the “
/SET”
switch toward you.
Instruments and controls/Multi function display
3-69
– CONTINUED –
3-70
Instruments and controls/Multi function display
3. The syst em will prompt a Yes/No
dialogue (“No” is selected first). To reset
the lifetime fuel consumption, select “Yes”
by operating the “
” switch.
4. Confirm the setting by pulling the “ /
SET” switch toward you.
5. Reconfirmation will be displayed. If
you are sure you want to proceed, select
“Yes” by operating the “
” switch.
6. Confirm the setting again by pulling
the “
/SET” switch toward you.
7. The system will notify you that the
setting is complete.

Related Topics

Instruments and controls
Ignition switch Key reminder chime Hazard warning flasher Meters and gauges Combination meter illumination Speedometer Odometer Double trip meter Tachometer Fuel gauge ECO gauge (if equipped) Warning and indicator lights Seatbelt warning light and chime Information display (if equipped) Outside temperature indicator Driving information display Clock Light control switch Turn signal lever Illumination brightness control Headlight beam leveler (if equipped) Fog light switch (if equipped) Wiper and washer Mirrors Inside mirror Auto-dimming mirror/compass (if equipped) Auto-dimming mirror/compass with HomeLink (if equipped) Outside mirrors Defogger and deicer Tilt/telescopic steering wheel Horn

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot