2010-2016 Subaru XV SUV Instruments and controls -> Wiper and washer User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Instruments and controls -> Wiper and washer for Your Subaru XV SUV First Generation (2010-2016)

3-75Instruments and controls/Fog light switchFog light switch (if equipped)Wiper and washerWARNINGIn freezing weather, do not use thewindshield washer until the wind-shield is sufficiently warmed by the washer fluid canfreeze on the windshield, blockingyour indicator light on the combinationmeter will illuminate when the front fogCAUTIONlights are illuminated.1)Headlight switch. Do not operate the washer con-2)Fog light switchtinuously for more than 10 sec-The front fog lights will turn on when theonds, or when the washer fluidfog light switch is placed in the “ ”tank is empty. This may causeposition while the headlights are in theoverheating of the washer the washer fluid level. while the headlight switch is in the “ ”frequently, such as at fuel . Do not operate the wipers when. for models with the auto on/off head-the windshield or rear window islights, while the headlight switch is in thedry. This may scratch the glass,“AUTO” position and the headlights turndamage the wiper blades andon automaticallymight cause the wiper motor tofail. Before operating the wiperTo turn off the front fog lights, turn theon a dry windshield or rearswitch back down to the “ ” , always use the wind-shield washer.– CONTINUED –
3-75
Instruments and controls/Fog light switch
Fog light switch (if equipped)
Wiper and washer
WARNING
In freezing weather, do not use the
windshield washer until the wind-
shield is sufficiently warmed by the
defroster.
Otherwise the washer fluid can
freeze on the windshield, blocking
your view.
The indicator light on the combination
meter will illuminate when the front fog
CAUTION
lights are illuminated.
1)
Headlight switch
. Do not operate the washer con-
2)
Fog light switch
tinuously for more than 10 sec-
The front fog lights will turn on when the
onds, or when the washer fluid
fog light switch is placed in the “ ”
tank is empty. This may cause
position while the headlights are in the
overheating of the washer motor.
following condition.
Check the washer fluid level
. while the headlight switch is in the “ ”
frequently, such as at fuel stops.
position
. Do not operate the wipers when
. for models with the auto on/off head-
the windshield or rear window is
lights, while the headlight switch is in the
dry. This may scratch the glass,
“AUTO” position and the headlights turn
damage the wiper blades and
on automatically
might cause the wiper motor to
fail. Before operating the wiper
To turn off the front fog lights, turn the
on a dry windshield or rear
switch back down to the “ ” position.
window, always use the wind-
shield washer.
– CONTINUED –
3-76 Instruments and controls/Wiper and washerover the windshield or rear window.. In freezing weather, be sure thatRefer to “Windshield washer. Grease, wax, insects or other mate-the wiper blades are not frozen tofluid” on the windshield or the wiperthe windshield or rear windowAlso, when driving the vehicleblade results in jerky wiper operationbefore switching on the there are freezing tempera-and streaking on the glass. If youAttempting to operate the wipertures, use non-freezing type wi-cannot remove those streaks afterwith the blades frozen to theper the washer or if the wiperwindow glass could cause not. Do not clean the wiper bladesoperation is jerky, clean the outer sur-only the wiper blades to bewith gasoline or a solvent, suchface of the windshield or rear windowdamaged but also might causeas paint thinner or benzine. Thisand the wiper blades using a sponge orthe wiper motor to fail. If thewill cause deterioration of thesoft cloth with a neutral detergent orwiper blades are frozen to thewiper -abrasive cleaner. After cleaning,window glass, be sure to operaterinse the window glass and wiperthe defroster, windshield wiperblades with clean water. The glass isdeicer (if equipped) or rear win-NOTEclean if no beads form on the glassdow defogger before turning on. The windshield wiper motor is pro-when you rinse with against overloads by a circuit. If you cannot eliminate the streaking. If the wipers stop during opera-breaker. If the motor operates continu-even after following this procedure,tion because of ice or some otherously under an unusually heavy load,replace the wiper blades with newobstruction on the window, thisthe circuit breaker may trip to stop theones. For replacement instructions,might cause the wiper motor tomotor temporarily. If this happens, parkrefer to “Replacement of wiper blades”fail even if the wiper switch isyour vehicle in a safe place, turn off o
3-76 Instruments and controls/Wiper and washer
over the windshield or rear window.
. In freezing weather, be sure that
Refer to “Windshield washer
. Grease, wax, insects or other mate-
the wiper blades are not frozen to
fluid” F11-29.
rial on the windshield or the wiper
the windshield or rear window
Also, when driving the vehicle
blade results in jerky wiper operation
before switching on the wipers.
when there are freezing tempera-
and streaking on the glass. If you
Attempting to operate the wiper
tures, use non-freezing type wi-
cannot remove those streaks after
with the blades frozen to the
per blades.
operating the washer or if the wiper
window glass could cause not
. Do not clean the wiper blades
operation is jerky, clean the outer sur-
only the wiper blades to be
with gasoline or a solvent, such
face of the windshield or rear window
damaged but also might cause
as paint thinner or benzine. This
and the wiper blades using a sponge or
the wiper motor to fail. If the
will cause deterioration of the
soft cloth with a neutral detergent or
wiper blades are frozen to the
wiper blades.
mild-abrasive cleaner. After cleaning,
window glass, be sure to operate
rinse the window glass and wiper
the defroster, windshield wiper
blades with clean water. The glass is
deicer (if equipped) or rear win-
NOTE
clean if no beads form on the glass
dow defogger before turning on
. The windshield wiper motor is pro-
when you rinse with water.
the wiper.
tected against overloads by a circuit
. If you cannot eliminate the streaking
. If the wipers stop during opera-
breaker. If the motor operates continu-
even after following this procedure,
tion because of ice or some other
ously under an unusually heavy load,
replace the wiper blades with new
obstruction on the window, this
the circuit breaker may trip to stop the
ones. For replacement instructions,
might cause the wiper motor to
motor temporarily. If this happens, park
refer to “Replacement of wiper blades”
fail even if the wiper switch is
your vehicle in a safe place, turn off the
F11-30.
turned off. If this occurs,
wiper switch, and wait for approxi-
promptly stop the vehicle in a
mately 10 minutes. The circuit breaker
safe place, turn the ignition
will reset itself, and the wipers will
switch to the “LOCK” (off) posi-
again operate normally.
tion and clean the window glass
. Clean your wiper blades and win-
to allow proper wiper operation.
dow glass periodically with a washer
solution to prevent streaking, and to
. Use clean water if windshield
remove accumulations of road salt or
washer fluid is unavailable. In
road film. Operate the windshield
areas where water freezes in
washer for at least 1 second so that
winter, use SUBARU Windshield
washer solution will be sprinkled all
Washer Fluid or the equivalent.
3-77Instruments and controls/Wiper and washer& Windshield wiper and washerFor a single wipe of the wipers, push the! Windshield washerlever up. The wipers operate until youswitchesrelease the wiper operates only when the ignition! Wiper intermittent time controlswitch is in the “ON” or “ACC” position.! Windshield wipersTo wash the windshield, pull the wipercontrol lever toward you. The washer fluidsprays until you release the lever. Thewipers operate while you pull the the wiper switch is in the “ ”position, turn the dial to adjust the operat-ing interval of the wiper. The operating: Mist (for a single wipe)interval can be adjusted in several steps: Offfrom the shortest interval to the longest.: Intermittent: Low speed: High speedTo turn the wipers on, push the wipercontrol lever turn the wipers off, return the lever tothe “ ” position.– CONTINUED –
3-77
Instruments and controls/Wiper and washer
& Windshield wiper and washer
For a single wipe of the wipers, push the
! Windshield washer
lever up. The wipers operate until you
switches
release the lever.
The wiper operates only when the ignition
! Wiper intermittent time control
switch is in the “ON” or “ACC” position.
! Windshield wipers
To wash the windshield, pull the wiper
control lever toward you. The washer fluid
sprays until you release the lever. The
wipers operate while you pull the lever.
When the wiper switch is in the “ ”
position, turn the dial to adjust the operat-
ing interval of the wiper. The operating
: Mist (for a single wipe)
interval can be adjusted in several steps
: Off
from the shortest interval to the longest.
: Intermittent
: Low speed
: High speed
To turn the wipers on, push the wiper
control lever down.
To turn the wipers off, return the lever to
the “ ” position.
– CONTINUED –
3-78 Instruments and controls/Wiper and washerNOTE& Rear window wiper andtion, the rear wiper will operate intermit-tently at intervals corresponding to thewasher switch – 5-doorvehicle speed. In this position, when youmove the select lever to the “R” position(CVT models) or the shift lever to thereverse position (MT models), the rearwiper will switch to continuous you move the select lever/shift leverfrom the “R” (reverse) position to anotherposition, the rear wiper will return tointermittent operation.! WasherTo wash the rear window while the rearwiper is operating, turn the knob switchupward to the “ ” position. The washerfluid sprays until you release the windshield washer fluid warninglight illuminates when the washer fluid: Washer(accompanied by wiper op-To wash the rear window when the reareration)level in the tank has dropped to thewiper is not in use, turn the knob switchlower limit. If the warning light illumi-downward to the “ ” position. The washer: Continuousnates, refill the tank with fluid. For thefluid sprays and the wiper operates until: Intermittentrefilling procedure, refer to “Wind-you release the knob.: Offshield washer fluid” (accompanied by wiper op-: eration)! Rear wiperTo turn the rear wiper on, turn the knobswitch turn the wiper off, return the knobswitch to the “ ” the switch turned to the “” posi-
3-78 Instruments and controls/Wiper and washer
NOTE
& Rear window wiper and
tion, the rear wiper will operate intermit-
tently at intervals corresponding to the
washer switch – 5-door
vehicle speed. In this position, when you
move the select lever to the “R” position
(CVT models) or the shift lever to the
reverse position (MT models), the rear
wiper will switch to continuous operation.
When you move the select lever/shift lever
from the “R” (reverse) position to another
position, the rear wiper will return to
intermittent operation.
! Washer
To wash the rear window while the rear
wiper is operating, turn the knob switch
upward to the “ ” position. The washer
fluid sprays until you release the knob.
The windshield washer fluid warning
light illuminates when the washer fluid
: Washer
(accompanied by wiper op-
To wash the rear window when the rear
eration)
level in the tank has dropped to the
wiper is not in use, turn the knob switch
lower limit. If the warning light illumi-
downward to the “ ” position. The washer
: Continuous
nates, refill the tank with fluid. For the
fluid sprays and the wiper operates until
: Intermittent
refilling procedure, refer to “Wind-
you release the knob.
: Off
shield washer fluid” F11-29.
Washer (accompanied by wiper op-
: eration)
! Rear wiper
To turn the rear wiper on, turn the knob
switch upward.
To turn the wiper off, return the knob
switch to the “ ” position.
With the switch turned to the “
” posi-

Related Topics

Popular Owner Manuals