2024-2026 Cupra Terramar SUV Driving -> Driving with electric drive User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Driving -> Driving with electric drive for Your Cupra Terramar SUV First Generation (2024-2026)

170
Driving
Driving with electric drive
Switching on the hybrid drive sys-
tem
✓ Valid for: hybrid vehicles
Switching on the hybrid drive activates the ve-
hicle's propulsion system. When the vehicle’s
drive system is switched on, the electric drive
is activated. The combustion engine starts au-
tomatically when the charge level of the high-
voltage battery is not suicient to run with the
electric drive, or if high drive power is required.
To access driving with the electric drive in the
infotainment system:
●
Select: > Charging > Battery Manager.
Requirements for switching on the drive sys-
tem
The drive system can be switched on when the
following conditions are met:
●
The high voltage battery has a suicient
charge level.
●
There is no charging cable plugged in.
●
The temperature of the high-voltage battery
is within the operating range.
●
There is a valid remote control key in the ve-
hicle.
Switching on the drive system
●
Press the ignition and start button once. The
ignition must be switched on.
●
Press the brake pedal and hold it down.
●
Set the gear selector switch to position N or
activate the parking lock P.
●
Press the ignition and start button until in-
dicator lamp lights up on the instrument
cluster. Do not press the accelerator. Release
the ignition and start button when the indica-
tor lamp lights up on the instrument clus-
ter. The mark on the power display changes
from to 0.
●
If the indicator lamp does not light up,
cancel and repeat the operation.
●
If the vehicle has been locked with the re-
mote control key, the ignition and start but-
ton is deactivated. If you are inside the vehi-
cle and have to start the engine, rst unlock
the vehicle or perform an emergency start
›››page169.
Note
A click is heard when the drive system is
turned on. This is completely normal and
does not mean there is a problem.
Detecting the drive system
With the electric drive, the motor makes no
noticeable noise when the drive system is
switched on or while driving. Therefore, you
cannot detect that the vehicle's drive system
is on by engine noise. Instead, the following
characteristics show that the vehicle is ready to
drive:
●
The indication 0 ›››page21 is displayed on
the power gauge of the instrument cluster.
●
The display light on the instrument cluster is
on, regardless of whether the vehicle’s exterior
lighting is on.
●
The indicator lamp is on in the instru-
ment cluster display.
●
An audible signal is heard.
Switching on the drive system in very low
outside temperatures
If the outside temperature is very low (approxi-
mately -27°C (-16°F) or lower), the high-voltage
battery may freeze and stop working. In this
case it's not possible to switch on the drive
system.
As soon as the temperature of the high-volt-
age battery has increased enough, the drive
system can be switched on again.
To ensure that the drive system can be
switched on, even in very low outside tempera-
tures, CUPRA recommends parking the vehicle
in a place protected from the cold.
Behaviour when moving o or stopping
The combustion engine only runs if necessary.
When the vehicle is stationary, the combus-
tion engine is normally switched o and the
Driving
171
Driving with electric drive
vehicle’s electrical systems are powered by the
high-voltage battery. The rev counter on the
instrument cluster remains at 0 ›››page21.
The combustion engine switches o in certain
driving conditions. This is normal and aims to
save fuel. In general, the power steering and
brake assist systems remain on. In isolated ca-
ses the system may require the combustion
engine to carry on running even when the ve-
hicle is stationary.
In traic jams the combustion engine may start
up while the vehicle is stationary to recharge
the high voltage battery for subsequent driving
o and stopping phases.
172
Driving
1)
The displayed symbol varies depending on the active operating mode and the charge level of the high-voltage battery.
Operating mode selection
✓ Valid for: hybrid vehicles
Fig.117 In the infotainment system: Battery
manager menu
The vehicle has dierent operating modes so
that it can always be optimally adjusted to ev-
ery situation while driving. Once the drive sys-
tem has been turned on, and provided that all
of the operating conditions required for this
purpose have been met, the Electric mode
operating mode is always activated in the rst
instance for electric driving.
Operating mode selection
●
Switch on the drive system.
●
Access the Battery manager menu of the
infotainment system ( > Charging > Battery
manager).
●
Select Electric Mode or Hybrid Mode in
the infotainment system. Further information
about the operating mode can be found in
›››Fig.117
4
.
Electric mode
(driving in electric mode)
1)
In electric mode, the vehicle basically drives in
electric only mode. To the extent possible, the
vehicle's combustion engine is not used.
All of the following conditions must be met for
the Electric mode to be activated:
●
The high voltage battery has a suicient
charge level.
●
The vehicle speed is lower than 130 km/h
(80 mph).
●
The high voltage battery temperature is
above -10°C.
If, while driving in Electric mode, the necessary
conditions are no longer met, the combustion
engine starts and electric driving is suspended.
In this case, the indicator
lights up on the
instrument cluster display.
Driving
173
Driving with electric drive
1)
The displayed symbol varies depending on the active operating mode and the charge level of the high-voltage battery.
1
2
3
The combustion engine starts when a kick-
down occurs in Electric mode. However, Elec-
tric mode remains on.
Hybrid mode
(use the battery's charge)
1)
This is the operating mode that allows you to
save most fuel.
The operating mode control unit tries to make
the most of the battery charge. For this pur-
pose, with active directions the navigation data
are also accessed.
In this operating mode, the electric motor and
the combustion engine share the work of driv-
ing the vehicle.
In hybrid operating mode, the power from
the battery charge is used optimally. If route
guidance is activated, the vehicle may auton-
omously recharge the high-voltage battery us-
ing the combustion engine.
Manual control of the battery charge
Manual control of the battery charge is only
possible in Hybrid mode. The option selected
by the user is only valid until the ignition is
switched o or the vehicle is switched to Hy-
brid mode or Electric mode.
Key to ›››
Fig.117:
The horizontal bar can be used to select a
lower theoretical charge level of the high
voltage battery. The system does not al-
low the selection of a higher charge level
than the one that is displayed. The vehicle
only uses the battery's charge when it is
above the selected theoretical charge
level. The rest is kept until the end of the
journey.
Maintaining the battery level
. The
high-voltage battery charge level is kept at
around the current level while driving. If
you accelerate harder or increase the ve-
hicle speed, the combustion engine starts
up. When permitted by the driver’s de-
mand for acceleration and the vehicle
speed, the vehicle switches back to elec-
tric mode.
CUPRA recommends using the charging
socket to charge the high-voltage battery,
whenever possible ›››page81.
Adjust the recuperation level. Allows you
to select between dierent levels of recu-
peration: Smooth, Auto or Strong. If there
is no active route, the system will oer the
activation of a predictive route to run in a
more eicient hybrid mode.
Smooth: In this mode recuperation is low.
The level of recuperation can be adjusted
in combination with the gear shift, using
the steering wheel paddles.
Auto: In “ECO” and “Comfort” driving
modes, recuperation is generally smooth,
although it can be strong, depending on
the driving situation. If the “Cupra” or
“Performance” driving mode is selected,
recuperation will be strong. The level of
recuperation can be adjusted in combina-
tion with the gear shift, using the steering
wheel paddles.
Strong: The vehicle recuperates as much
energy as possible, depending on the sit-
uation. If the brake pedal is depressed, the
vehicle also recovers energy through the
high-voltage system. If the recuperation
level is Strong, the brake lights will also
light up to indicate that the vehicle is de-
celerating.
For the most eicient driving possible, we
recommend activating the eiciency as-
sistant ›››page203, driving in “ECO”
driving mode, setting the gear shift to D
and the recuperation mode to Auto.
WARNING
Medium and strong energy recuperation can
cause loss of traction and skidding, particu-
larly on slippery roads. This can lead to loss of
control of the vehicle, accidents and serious
injuries.
●
Only activate the high recuperation level if
visibility, weather, road and traic conditions
permit, and if other road users are not at risk
due to your vehicle's deceleration behaviour
and driving style.
174
Driving
WARNING
The higher the charge level of the high-volt-
age battery, the lower the braking eect of
the engine, to the extent that there may be
no braking eect due to recuperation. This
can change the behaviour of the vehicle,
which can lead to accidents and serious or
fatal injuries.
●
Do not fully charge the high-voltage bat-
tery at high altitude, such as at the top of a
mountain pass, to allow the use of the recu-
peration braking eect when driving down-
hill.
●
Reduce speed before driving on a steep
gradient.
●
Reduce the vehicle’s speed by using the
vehicle brakes when driving on a steep gradi-
ent.
●
Note that there is a higher load on the ve-
hicle’s brakes if there is no engine braking
eect.
Show the active operating mode
The operating mode active at any given time
is displayed on the instrument cluster display,
e.g. .
WARNING
Switching to a dierent operating mode
while driving can distract you from traic
conditions and cause accidents.
Note
Information about the operating mode that
is currently active is displayed on the instru-
ment cluster display, along with the charge
level of the high-voltage battery.
Vehicle sound
✓ Valid for: hybrid vehicles
The electric drive makes much less noise than
a combustion engine. In the versions for some
countries, articial vehicle sound is generated
to allow the vehicle to be heard better from
the outside. At higher speeds, when the noise
produced by the tyres and the wind increases,
the vehicle's sound automatically fades out.
WARNING
During electric driving, the auditory percep-
tion of the vehicle by other road users may
be much lower. This is especially true in traf-
c-restricted areas and when manoeuvring
or reversing. Accident hazard!
Troubleshooting
✓ Valid for: hybrid vehicles
Drive: Fault! Stop the vehicle safely
The warning lamp lights up red.
There is a fault in the vehicle’s drive system.
The vehicle's drive system is no longer availa-
ble. Park the vehicle in a safe place as soon as
possible. Seek professional assistance.
Drive: Fault! The electric drive is not
working properly. Visit a workshop
The warning lamp lights up yellow.
There is a fault in the vehicle’s drive system.
Drive slowly to a specialised workshop to have
the fault repaired.
Drive: Warning! Power is limited. Check
the manual
The warning lamp lights up yellow.
Performance limited. The high-voltage battery
may not be suiciently charged or may have
reached its operating temperature limit, for ex-
ample in very cold outside temperatures.
Vehicle sound: Fault! Pedestrians can-
not hear the vehicle. Visit a workshop
The warning lamp lights up yellow.
There is a vehicle sound fault. Drive with ut-
most care, as other road users may not be able
to hear the electric vehicle. Go immediately
to a specialised workshop to have the fault re-
paired.

Related Topics

Popular Owner Manuals