2024-2026 Cupra Terramar SUV Driving -> DSG automatic transmission User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Driving -> DSG automatic transmission for Your Cupra Terramar SUV First Generation (2024-2026)

Driving
177
DSG automatic transmission
Note
●
In vehicles with an automatic gearbox,
you can control whether the engine should
switch o or not by reducing or increasing
the brake force applied. While the vehicle re-
mains stopped, the engine will not stop if the
brake pedal is slightly pressed, in traic jams
with frequent stopping and starting for ex-
ample. As soon as strong pressure is applied
to the brake pedal, the engine will stop.
●
When stopped, the brake pedal must be
kept pressed to ensure that the vehicle does
not move.
●
If the lever is placed in position D, N or S af-
ter engaging reverse gear, 10km/h (6mph)
in a forwards direction must be reached for
the system to be in a condition to stop the
engine.
Manually connecting and discon-
necting the Start-Stop system
Not valid for PHEV hybrid vehicles
Fig.118 In the infotainment system: Start-
Stop system (accessible from dierent
infotainment menus).
›››
Fig.118:
System disconnected.
System connected.
If you do not wish to use the system, you can
switch it o manually:
●
In the infotainment system select > Assis-
tants > Smart Assistants.
Note
When the ignition is switched on, the Start-
Stop system activates automatically.
Troubleshooting
Not valid for PHEV hybrid vehicles
Indications for the driver on the instrument
cluster screen
A warning will be displayed whenever there is
an error or the Start-Stop system is switched
on/o.
“Start the engine manually”
●
This indication shows that the Start-Stop
system cannot restart the engine.
This happens for 2 reasons: if the driver's door
has been opened or if the driver has unbuck-
led the seat belt.
“Start-Stop system: Fault! Function not
available”
●
There is a fault in the Start-Stop system. Take
the vehicle to a workshop to have the fault re-
paired.
DSG automatic transmis-
sion
Introduction
Your vehicle is equipped with an electronically
controlled manual gearbox. Torque between
the engine and the gearbox is transmitted via
two independent clutches. They replace the
178
Driving
torque converter found on conventional auto-
matic gearboxes and allow for smooth, unin-
terrupted acceleration of the vehicle.
The Tiptronic system allows the driver to
change gears manually ›››page179, Chang-
ing gear in Tiptronic mode.
Gear selector positions
Fig.119 On the centre console: selector
lever.
The gear selector position is shown by the
corresponding sign lighting up. The engaged
gear is also displayed on the screen in manual
shift positions M, D, S and E (when the Eco
›››
page185 engine setting is selected in the
Individual prole).
- Parking lock
When the P button is pressed, the drive wheels
are locked. Only press P when the vehicle is
stationary ››› .
To press the P button you must press the brake
pedal simultaneously.
– Reverse gear
Reverse gear must be engaged only when the
vehicle is stationary and the engine is idling
››› .
To engage reverse gear R, you must press the
brake pedal simultaneously. The reverse lights
switch on when the reverse gear R is selected
and the ignition is on.
– Neutral
In this position, the gear is in neutral.
Press the brake pedal to move the lever from
N to D/S when the vehicle is stationary or at
speeds below 3km/h (2mph) ››› .
– Permanent forward drive position
The D/S position enables the gears to be op-
erated in normal mode (D) or sport mode (S).
To select Sport mode S, move the lever back-
wards. Pushing the lever again will select nor-
mal mode D. The selected driving mode is dis-
played on the instrument cluster display.
In normal mode (D), the gearbox selects the
best gear ratio. This depends on the engine
load, speed and the dynamic regulation pro-
gram (DRP).
Sport mode(S) should be selected for a sporty
driving style. This setting makes use of the en-
gine's maximum power output. When acceler-
ating, gear shifting operations are perceptible.
Under certain circumstances (e.g. on moun-
tain roads) it can be advantageous to switch
to tiptronic mode ›››page179, to adapt the
gears to suit the road conditions.
WARNING
●
Take care not to press the accelerator
pedal when the vehicle is stopped. The vehi-
cle could start moving immediately (in some
cases even if the parking brake is engaged)
resulting in the risk of an accident.
●
Never move the lever to position R when
driving. Failure to follow this instruction
could result in an accident or failure.
●
With lever in any position, the foot brake
must be depressed whenever the engine is
running. This is because an automatic gear-
box still transmits power even at idling speed.
●
Do not accelerate while selecting a gear,
with the car stationary and the engine run-
ning. Failure to follow this instruction could
result in an accident.
Driving
179
DSG automatic transmission
●
The driver must never leave the vehicle
while the engine is running and with a gear
engaged. Switch on the electronic parking
brake and select the parking lock (P).
Note
●
If the lever is moved accidentally to N when
driving, release the accelerator and let the
engine speed drop to idle before selecting
gear range D or S again.
●
If the power supply is interrupted while the
P parking lock is active, it will not be possible
to move the lever. If this should happen the
manual release can be used. In this case, you
should seek professional assistance.
Note
●
If a gear has been selected, the vehicle
does not move forwards or back. Proceed to
the next mode:
–
If the vehicle does not move in the
desired direction, the gear ratio may not
be correctly engaged by the system. De-
press the brake pedal and reselect the gear
range.
–
If the vehicle still does not move in the
desired direction, there is a system failure.
Seek specialist help and have the system
checked.
Changing gear in Tiptronic mode
Fig.120 Steering wheel: automatic gearbox
levers
Tiptronic gives the driver the option to change
gears manually.
When you change to the Tiptronic pro-
gramme, the vehicle remains in the currently
selected gear. This is possible as long as the
system is not changing gear automatically due
to a traic situation.
Using Tiptronic with the steering wheel pad-
dles
The gear shift paddles can be used when the
selector lever is in the D/S position.
●
Press the
+
gear shift paddle to change up a
gear ›››
Fig.120.
●
Press the
–
gear shift paddle to change
down a gear.
●
To exit the Tiptronic mode, pull the right-
hand gear shirt paddle towards the steering
wheel for approximately 1 second.
To keep Tiptronic mode permanently switched
on, move the selector lever to the S position.
If the selector lever is in position D and the
gear shift paddles are not operated for some
time, the Tiptronic mode will automatically be
switched o.
NOTICE
●
When accelerating, if a higher gear is not
selected, it will automatically change shortly
before reaching the maximum permitted
RPM.
●
Also, if a lower gear is selected, the system
will not change until it detects that the en-
gine will not reach its maximum RPM.
Driving with an automatic gearbox
Shifting to a higher or lower gear is automatic.
The engine can only be started with the lever in
the N position and the P button must be lit up
(the parking lock remains active).
Driving downhill
Under certain circumstances it may be advan-
tageous to use the Tiptronic mode to select
the gear manually according to driving condi-
tions ››› .
180
Driving
Stop/Park
To park on at ground, just press the P
›››Fig.119 button. On slopes the parking
brake should rst be applied and then press
the P button.
If the driver door is opened and the P but-
ton has not been activated, the vehicle could
move. The following warning is displayed on
the instrument panel: Gear change: Selec-
tor lever in the drive position!. A buzzing
sound is also heard.
Stopping on a downhill
Always apply the brake pedal rmly to prevent
the vehicle from moving; if necessary, apply
the electronic parking brake ››› .
Do not accelerate while a range of gears is en-
gaged to prevent the car from rolling downhill
››› .
Starting o uphill with the Auto Hold func-
tion
●
Once you have engaged a gear, take your
foot o the brake pedal and gently press the
accelerator.
Starting o uphill without the Auto Hold
function
●
Once you have engaged a gear, take your
foot o the brake pedal and gently press the
accelerator. The Hill Hold Control (HHC) will
keep the vehicle braked for a few seconds to
prevent the vehicle from rolling backwards and
give the driver time to move o.
WARNING
Observe the safety warnings ››› in Gear
selector positions on page178.
●
Never allow the brake to rub and do not use
the brake pedal too often or for long peri-
ods, as the brakes can overheat. This reduces
the braking power, increases the braking dis-
tance or even causes a brake system fault.
●
If you have to stop on a hill, keep the vehi-
cle’s brakes applied with the brake pedal or
parking brake.
NOTICE
●
When stopping the vehicle on an uphill
slope, do not try to avoid shifting into gear
and depressing the accelerator. This could
overheat and damage the automatic gear-
box.
●
If you allow the vehicle to roll with the lever
in position N and the engine o, the auto-
matic gearbox will be damaged due to a lack
of lubrication.
●
In certain driving situations or traic con-
ditions, the gears could overheat and be
damaged! If the warning lamp lights up,
stop the vehicle as soon as you can and wait
for the gearbox to cool ›››page182.
●
If the gearbox operates in emergency
mode, have the fault repaired by a specialist
workshop without delay.
Kick-down
The kick-down device provides maximum ac-
celeration when the gear selector lever is in the
positionsD, S or in Tiptronic mode.
When the accelerator pedal is fully depressed,
the automatic transmission shifts to a lower
gear, depending on speed and engine speed.
This uses the vehicle's maximum acceleration
››› .
The shift to the next higher gear will not take
place until the preset maximum engine RPM is
reached.
WARNING
Please note that if the road surface is slippery
or wet, the kickdown feature could cause the
driving wheels to spin, which could result in
skidding.
Launch-control program
The Launch-control program enables maxi-
mum acceleration from a standstill.
Condition: the engine must have reached op-
erating temperature and the steering wheel
must not be turned.
Driving
181
DSG automatic transmission
To use Launch-control you must disconnect
the traction control (TCS) or activate the ESC
Sport or ESC OFF mode, using the Infotain-
ment system menu: press the function button
> Assistants > Smart Assistants. The lamp
will remain on.
●
Press the brake pedal with your left foot and
hold it down for at least one second.
●
Set the selector lever to position S or Tip-
tronic, or select the Sport or Cupra Drive Pro-
le ›››page185.
●
With your right foot, press the accelerator
down to the full throttle or kick-down position.
The engine speed is set at approximately 2000
rpm to 4000 rpm, depending on the engine
version.
●
Take your left foot o the brake pedal. The
vehicle starts with maximum acceleration.
WARNING
●
Always adapt your driving style to the traf-
c conditions.
●
Only use the Launch control programme
when road and traic conditions permit, and
make sure your manner of driving and accel-
erating the vehicle does not inconvenience
or endanger other road users.
●
Make sure that the ESC remains switched
on. Please note that when the TCS and ESC
are deactivated, the wheels may start to spin,
causing the vehicle to lose grip. Accident
hazard!
●
After moving o, you should activate the
TCS or deactivate the ESC “Sport” mode
again using the ESC button ›››Fig.122.
Note
●
Dynamic driving or using a launch-control
program may considerably raise the temper-
ature of the catalytic converter or gearbox. In
this case, the program may be out of service
for a few minutes. The program may be used
again once the cooling phase is complete.
●
Accelerating with the Launch control pro-
gramme places a heavy load on all parts of
the vehicle. This can result in increased wear
and tear.
Inertia mode
The inertia mode allows you to travel certain
distances without using the accelerator, which
saves fuel. Plan ahead and use the inertia
mode to “let” the vehicle “roll”.
Activation of the inertia mode
Combustion engine vehicles (not PHEVs, not
mHEVs):
●
The function is only available when the “Eco”
drive prole is selected, when the accelerator
is not depressed and at speeds between 7 and
130km/h (between 4 and 80mph).
●
If when driving below about 22km/h (about
14mph) and you press the brake with the in-
tention of stopping, the engine may switch o
and remain o until the vehicle comes to a
stop. The system can automatically start the
engine to ensure that power is supplied to the
electrical system or to ensure its own start-up.
Mild hybrid electric vehicles (mHEV):
●
The function is only available when the
“Eco” or “Comfort” drive prole is selected,
when the accelerator is not depressed and at
speeds between 7 and 160km/h (between 4
and 99mph).
●
If you apply the brakes and the vehicle
slows to a stop below about 40km/h (about
25mph), the engine switches o until the vehi-
cle comes to a stop. The system can automat-
ically start the engine to ensure that power is
supplied to the electrical system or to ensure
its own start-up.
●
If you press the brake when in inertia mode
to stop above about 40km/h (about 25mph),
the inertia mode will be interrupted and the
engine will start.
182
Driving
●
When stopping without braking, the engine
automatically restarts at minimum speed to al-
low manoeuvring.
Start and cancel inertia mode
Start:
1. Select the “Eco” drive prole.
Or, in mHEVs, select the “Comfort” drive
prole.
2. Take your foot o the accelerator. The en-
gine will disengage and run at idle. The
vehicle runs without the engine braking ef-
fect. The engine may switch o in vehicles
with a mHEV system.
Cancelling inertia mode:
1. Press the accelerator.
Alternatively, pull the automatic gear shift
paddle towards the steering wheel.
WARNING
●
If the inertia mode has been switched on,
take into account, when approaching an ob-
stacle, that the vehicle will not decelerate in
the usual manner: Accident risk!
●
When using inertia mode while travelling
down hills, the vehicle can increase speed:
Accident risk!
●
If other users drive your vehicle, warn them
about inertia mode.
NOTICE
The operation of the inertia mode in combi-
nation with hybrid engines (mHEV and PHEV)
can cause the combustion engine to switch
o.
NOTICE
The inertia mode will be automatically dis-
connected on gradients steeper than 15%.
Troubleshooting
The engine does not start
The indicator lamp lights up green.
The brake is not depressed, e.g. when trying to
change the gear selector lever.
●
To select a gear range, press the brake pedal.
Indications on the instrument cluster display:
Clutch
Clutch overheated Please stop!
●
The clutch has overheated and could be
damaged. Stop and wait for the gearbox to
cool with the engine idling and press the P
parking lock button. When the warning lamp
and the driver message turn o, go to a spe-
cialised workshop to get the fault repaired. If
they do not turn o, do not continue driving.
Seek specialist assistance.
Faults in the gearbox
Gearbox: Fault! Stop the vehicle and
place the lever in P
●
There is an anomaly in the gearbox. Stop
the vehicle in a safe place and do not continue
driving. Seek specialist assistance.
Gearbox: System fault! You may con-
tinue driving
●
Have the fault corrected by a specialised
workshop without delay.
Gearbox: System fault! You can con-
tinue driving with restrictions. Reverse gear
disabled
●
Take the vehicle to a specialised workshop
and have the fault repaired.
Gearbox: System fault! You can con-
tinue driving in D until switching o the en-
gine
●
Stop the vehicle in a safe place. Seek special-
ist assistance.
Gearbox: too hot. Adapt your driving
accordingly
●
Continue driving slowly. When the warning
lamp goes out, you can continue driving nor-
mally.

Related Topics

Popular Owner Manuals