Get KNOWING YOUR CAR -> INTERIOR LIGHTS Guide for Fiat 500 SUV Second Generation (2020-2025)

opposite direction or when following a

car travelling in the same direction.

This function is enabled via the

Uconnect™ system (see "Settings" in

the"Vehicle mode" paragraph in the

"Multimedia" section).

When the speed of 38 km/h is

exceeded again, the function is

activated automatically again.

If the lever is pulled again in this

condition, to request main beam

headlight deactivation, the function

remains off and the main beam

headlights switch off.

"Lane Change" function

If you wish to signal a lane change,

place the left stalk in the unstable

position for less than half a second.

The direction indicator on the side

selected will be activated for 5 flashes

and then go out automatically.

Turn the light switch to the AUTO

position (B) fig. 37. The first time the

main beam headlights are activated

(pushing the left stalk towards the

dashboard), the function is activated

COURTESY LIGHTS

The function can be enabled and

timed using the "Settings" menu of the

Uconnect™ system (see "Settings" in

the"Vehicle mode" paragraph in the

"Multimedia" section).

To deactivate the automatic function

rotate the light switch ring to position

(warning light

instrument panel).

comes on in the

FLASHING THE

HEADLIGHTS

If the main beam headlights are actually

on, the warning light will also come

on in the instrument panel).

Pull the left lever towards the steering

wheel, to the unstable position; when

released it returns automatically to

the stable, central position. With main

beam headlights on, the warning light

on the instrument panel will come

on at the same time.

When the doors are unlocked, the

side/tail lights and puddle lights come

on for the time set in the menu.

Once any door is opened, the lights

remain on for a further 180 seconds, or

for a further 10 seconds after the door

is closed.

When the speed is higher than 38 km/h

and the function is active, the lights

switch off if the lever is taken again to

the stable central position.

When the speed is lower than 15 km/h

and the function is active, the function

switches the main beam headlights off.

If the fixed main beam headlights are

operated quickly again (taking the lever

again to the stable central position and

taking it back in a few seconds on the

fixed main beam headlight position),

DIRECTION INDICATORS

Take the left stalk to the (stable)

position:

"FOLLOW ME HOME"

DEVICE

This allows the space in front of the car

to be lit for a set time.

upwards: activates the right

direction indicator;

downwards: activates the left

direction indicator.

Warning light or will blink

on the instrument panel. The

direction indicators are switched off

automatically when the steering wheel

is straightened.

Activation

With the ignition device turned to STOP

or removed, pull the stalk towards the

steering wheel within 2 minutes from

when the motor is turned off.

the warning light

will switch on

in the instrument panel and the main

beam headlights will be switched on

constantly until the speed exceeds

38 km/h.

Each time the stalk is moved, the lights

stay on for an extra 30 seconds up to

a maximum of 210 seconds; then the

lights are switched off automatically.

Also, each time the stalk is operated,

LIGHT BEAM DIRECTION

The correct aiming of the headlights is

important for the comfort and safety

of not only the driver but all other road

users. This is also covered by a specific

rule of the highway code.

the

instrument panel switches on.

The warning light comes on

warning light on the

The headlights must be correctly

aligned to guarantee the best visibility

conditions for all drivers while travelling

with headlights on.

when the stalk is first moved and stays

on until the function is automatically

deactivated. Each movement of the

stalk only increases the amount of time

the lights stay on.

F0S1113

Contact a Fiat Dealership to have the

headlights checked and adjusted.

Check the light beam alignment

every time the load or its distribution

changes.

Position 0: one or two people in the

front seats

Position 1: 4 people

Position 2: 4 people + load in the

boot

Deactivation

Hold the stalk pulled towards the

steering wheel for more than 2 seconds

or turn the ignition device to the

ENGINE position.

HEADLIGHT ALIGNMENT

CORRECTOR

Position 3: Driver + maximum

permitted load stowed in the boot

WELCOME LIGHT

(where provided)

This device works with the ignition

device in the ENGINE position and the

dipped headlights on.

Depending on the version, with the

ignition device in the STOP position,

an animated sequence of front lights

may can be shown when the doors

of the car are unlocked. Then they

light up fixed. To enable the function

set the courtesy lights in a state other

than OFF on the Uconnect™ system

(see "Settings" in the "Vehicle mode"

paragraph in the "Multimedia" section).

Only the direction indicators will light up

when only the tailgate is unlocked.

Activating the alarm or hazard lights will

disable the welcome light feature.

WARNING Check the headlight

alignment each time the weight of the

load transported changes.

Headlight alignment adjustment

To adjust, press the buttons

fig. 39 on the control display located on

the left side of the dashboard (left-hand

drive versions).

ADJUSTING THE

HEADLIGHTS ABROAD

Cars with LED headlight do not need

headlight adjustment when driving in

countries with opposite traffic.

The adjustment position is shown on

the display:

Halogen headlights, if fitted on the car,

are adjusted for driving in the country

where the car was originally purchased.

In this case, when travelling in countries

with opposite driving direction, to avoid

dazzling the drivers on the other side

of the road, you need to cover areas of

the headlight according to the Highway

code of the country you are travelling

in: fig. 40 (front right headlight), fig. 41

(front left headlight).

to avoid draining the 12V battery. On

some versions, the lights switch on and

off only when the front driver side door

is opened or closed.

during the day; where it is not compulsory,

the use of daytime running lights is

permitted.

25) Daytime running lights cannot replace

dipped beam headlights while driving

at night or through tunnels. The use

of daytime running lights is governed

by the highway code of the country in

which you are driving. Comply with legal

requirements.

CEILING LIGHT TIMING

Ignition

Two different switching-on modes are

provided:

when the doors are unlocked, a timer

will be activated for about 27 seconds;

move the ignition device to STOP

to activated a timed sequence of

approximately 27 seconds.

INTERIOR LIGHTS

FRONT CEILING LIGHT

Switch fig. 42 can assume three

different positions:

F0S1223

Switching off

Three modes are provided for

switching off:

(A) light always off;

(B) the light turns on and off when

the doors are opened or closed;

when all the doors are locked, a 10-

second timer is activated. This timing

will stop when the ignition device is

turned to the ENGINE position;

locking of the doors:

the interior lights are turned off after

15 minutes to preserve the 12V battery,

even if the switch fig. 42 is in position

(C).

F0S1224

BOOT COURTESY LIGHT

(where provided)

F0S1114

IMPORTANT

The lamp comes on automatically when

the boot is opened and goes out when

it is closed.

WARNING Before getting out of the

car, make sure that the switch is in

the central position: ensure that lights

are off with the doors closed in order

24) The daytime running lights are an

alternative to the dipped headlights while

driving during the daytime in countries

where it is compulsory to have lights on

KNOWING YOUR CAR -> INTERIOR LIGHTS for Your Fiat 500 SUV Second Generation (2020-2025)

Related Topics

KNOWING YOUR CAR

Popular Owner Manuals

Latest Owner Manuals