Get KNOWING YOUR CAR -> PROGRAMMING THE CLIMATE CONTROL SYSTEM Guide for Fiat 500 SUV Second Generation (2020-2025)

windscreen glass is being washed by

hand or the wipers are stuck to the

screen by ice).

stroke for each two strokes of the

windscreen wiper;

WARNING

With the ring in position , the wiper

active and reverse gear engaged, the

wiper is activated in synchronous

mode.

8) Never use the screen wiper to remove

layers of snow or ice from the windscreen

glass. In such conditions, the wiper

may be subjected to excessive stress

and the motor cut-out switch, which

prevents operation for a few seconds, may

intervene. If operation is not restored,

contact a Fiat Dealership.

9) Do not operate the windscreen wiper

with the blades lifted from the windscreen.

10) Do not activate the rain sensor when

washing the car in an automatic car wash.

11) Make sure the device is switched off if

there is ice on the windscreen glass.

It is possible to reactivate the automatic

wiping mode in three ways:

by turning the ring to the position

and then returning it to the or

position;

With the ring in position , the rear

window wiper is stopped.

by moving the stalk upwards to the

position;

NOTE If automatic wiping mode is

active and the sensor does not detect

water, the rear window wiper will stays

still when the ring is turned to position

MIST

upon exceeding the 5 km/h speed

and the sensor detects rain.

REAR WINDOW WIPER /

WASHER

Push the stalk towards the dashboard

(rocking position) to activate the rear

window washer jet. Keep pushing

the lever to automatically activate

both the rear window washer jet and

the rear window wiper with a single

movement. Releasing the stalk will

activate three strokes, as described for

the windscreen wiper.

This operates only with the ignition

device at ENGINE.

PROGRAMMING THE

CLIMATE CONTROL

SYSTEM

The ring (B) fig. 43 can be set to the

following positions:

Wiper off

Intermittent wiping

Continuous wiping

(where provided)

The system provides two types

of remote climate control system

programming:

Rear Window Wiper

Turn the ring to (B) fig. 43 to operate

the rear window wiper:

timely start of the climate control

system: this can be activated through

the dedicated smartphone app (where

provided). Refer to the "Connected

Services - Uconnect Services" chapter

in the "Multimedia" section.

Programming the climate control

system with start time: This can be

activated either through the dedicated

smartphone app (where provided) or

IMPORTANT

continuous: when the ring is in

;

position

26) If the window needs to be cleaned,

make sure the device is turned off or the

ignition device is in the STOP position.

27) Driving with worn windscreen/rear

window wiper blades is a serious risk,

because visibility is reduced in bad

weather.

intermittent: when the ring is in

position and the windscreen wiper

wiper is stopped;

synchronous: when the ring is in

position and the windscreen wiper is

moving or set to AUTO. In this mode,

the rear window wiper makes one

by programming a start time using the

Uconnect™ system (see "ENGINE"

in the"Vehicle mode" paragraph of the

"Multimedia" section).

heated windscreen where fitted) are

also activated.

How to start climate control system

programming

Select the programming function on

the dedicated app (where provided.

Refer to the "Multimedia" section) to

start the climate control system on-

demand or select an climate control

system programming start time on the

Uconnect™ system or dedicated app

(refer to the "Multimedia" section).

The doors of the car will lock, the

climate control system programming

will start and the car will go into

ENGINE mode. If the climate control

system is started on-demand, the car

will remain in ENGINE mode for 15

minutes; if the climate control system is

programmed to start at a certain time,

the car will remain in ENGINE mode.

NOTES

Programming the climate control

system with start time

Failed climate control

system programming

messages

Select a time to start climate control

system programming using the

Uconnect™ system or the dedicated

app (refer to the "Multimedia" section);

the passenger compartment climate

control system will remain active unless

the ignition device is pressed;

The on-demand starting and

programming of the climate control

system can be successful in the

following conditions:

If the on-demand or programmed

climate control system switch-on fails

or ends early, dedicated messages will

be displayed on the instrument panel

display.

How to use the

climate control system

programming functions

Starting the climate control system

Select the programming function on

the dedicated app (where provided.

Refer to the "Multimedia" section).

The passenger compartment climate

control system will remain active for 15

minutes unless the ignition device is

pressed.

This function can be activated twice

after which it is necessary to turn the

ignition device to ENGINE to allow

turning on the climate control system

app (where provided) on-demand

again.

Doors closed

Bonnet closed

Boot closed

Hazard lights not active

Alarm not active

Adequate 12V battery state of

charge

Ignition device in the STOP position

Transmission in P position

If the start on-demand function has

not been activated twice

In case of motor malfunction/fault,

the climate control system

programming will be disabled.

For safety reasons, both when the

climate control system is started on-

demand or programmed with start

time, the wipers are disabled when the

function is active. For safety reasons,

the windows are disabled when the

climate control system is started on-

demand.

If the key is not inside the car

(necessary condition for programming

the climate control system with start

time)

If the ambient temperature is lower

than 4.5 °C when the function is

started, the electric defrosters (heated

rear window, heated mirrors and

In case of activation of the climate

control system on-demand, the sunroof

and soft top are also disabled.

Two 15-minute cycles of climate

control system operation are possible

after which the ignition device must

be turned to the ENGINE position to

perform new start cycles.

use device (C) to adjust the diffuser

to the desired position (up / down / left

/ right);

CLIMATE CONTROL

SYSTEM

PASSENGER

Central air vents

(A) fig. 47 - Adjustable and directable

central vents:

COMPARTMENT AIR

DIFFUSERS

Side air diffusers

How to finish programming the

climate control system without

driving the car

use device (B) to adjust the diffuser

to the desired position (up / down / left

/ right);

(A) fig. 45 - Fixed side air diffuser (driver

and passenger side).

If the climate control system starts

up on time, select the end of charging

function on the dedicated app (where

provided. Refer to the "Multimedia"

section) or wait for the end of the start

cycle (about 15 minutes).

In case of programming the climate

control system with start time, finish

charging through the programming

function on the dedicated app (where

provided. Refer to the "Multimedia"

section).

F0S1123

F0S1125

How to stop climate control system

programming and drive the car

Programming can be interrupted

with time or start the climate control

system on time by moving the ignition

device to the START position. A

dedicated message will appears on the

instrument panel.

F0S1124

(B) - Adjustable side vents:

KNOWING YOUR CAR -> PROGRAMMING THE CLIMATE CONTROL SYSTEM for Your Fiat 500 SUV Second Generation (2020-2025)

Related Topics

KNOWING YOUR CAR

Popular Owner Manuals

Latest Owner Manuals