2004-2009 Nissan Micra 4 Door Starting and driving User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Starting and driving for Your Nissan Micra 4 Door Third Generation (2004-2009)

5 Starting and driving
Break-in schedule
....
.................................................................................... 5-3
Before starting engine
....
............................................................................ 5-3
Precautions when starting and driving
....
............................................... 5-3
Exhaust gas (carbon monoxide)
....
.................................................... 5-3
Three-way catalyst (gasoline engine model)
....
............................. 5-4
Care when driving
....
................................................................................... 5-5
Engine cold start period
....
.................................................................. 5-5
Loading luggage
....
............................................................................... 5-5
Driving in wet conditions
....
................................................................ 5-5
Driving in winter conditions
....
............................................................ 5-5
Ignition switch (model without intelligent Key system)
....
.................. 5-5
Automatic Transmission (AT)/Continuously Variable
Transmission (CVT)
....
.......................................................................... 5-5
Manual transmission (MT)
....
.............................................................. 5-5
Steering lock
....
...................................................................................... 5-6
Key positions
....
...................................................................................... 5-6
Push-button ignition switch (model with Intelligent
Key system)
....
............................................................................................... 5-6
Precautions on push-button ignition switch operation
....
........... 5-6
Intelligent Key system
....
...................................................................... 5-6
Steering lock
....
...................................................................................... 5-7
Ignition switch positions
....
.................................................................. 5-8
Intelligent Key battery discharge
....
................................................... 5-8
Starting engine (model without Intelligent Key system)
....
................ 5-9
Gasoline engine
....
................................................................................ 5-9
Diesel engine
....
..................................................................................... 5-9
Starting engine (model with Intelligent Key system)
....
................... 5-10
Gasoline engine
....
............................................................................. 5-10
Diesel engine
....
.................................................................................. 5-11
Driving vehicle
....
....................................................................................... 5-11
Driving with Automatic Transmission (AT)
....
............................... 5-11
Driving with Continuously Variable Transmission (CVT)
....
...... 5-14
Driving with Manual Transmission (MT)
....
................................. 5-17
Idling Stop System (for Hong Kong)
....
.............................................. 5-19
Operating Idling Stop System
....
................................................. 5-20
Idling Stop OFF switch
....
.............................................................. 5-21
Stop/Start System (if equipped for Europe)
....
................................ 5-21
Normal operation
....
......................................................................... 5-21
Stop/Start System display and indicators
....
............................ 5-22
Precautions on Stop/Start
....
........................................................ 5-23
Stop/Start System OFF switch
....
............................................... 5-23
Vehicle Dynamic Control (VDC) system (if equipped except for
Europe, Australia and New Zealand)
....
............................................. 5-24
Vehicle Dynamic Control (VDC) OFF switch
....
....................... 5-25
Vehicle Dynamic Control (VDC) system (for Australia and
New Zealand)
....
....................................................................................... 5-25
Vehicle Dynamic Control (VDC) OFF switch
....
....................... 5-26
Electronic Stability Program (ESP) System (if equipped
for Europe)
....
............................................................................................ 5-27
Electronic Stability Program (ESP) OFF Switch
....
................. 5-27
Speed limiter (if equipped for Europe)
....
.......................................... 5-28
Speed limiter operations
....
............................................................ 5-28
Cruise control (if equipped)
....
.............................................................. 5-30
Precautions on cruise control
....
.................................................. 5-30
Cruise control operations
....
.......................................................... 5-30
Parking
....
.................................................................................................... 5-32
Sonar (parking sensor) system (if equipped)
....
............................... 5-34
Parking Sensor Indicator
....
........................................................... 5-34
Parking space measurement operation (if equipped)
....
........ 5-35
Trailer towing
....
......................................................................................... 5-37
Electric power steering system
....
........................................................ 5-37
Brake system
....
........................................................................................ 5-38
Brake precautions
....
....................................................................... 5-38
Brake assist (if equipped)
....
......................................................... 5-39
Anti-lock Braking System (ABS) (if equipped)
....
............................. 5-39
Using system
....
................................................................................... 5-39
Self-test feature
....
.............................................................................. 5-39
Normal operation
....
............................................................................ 5-40
Vehicle security
....
..................................................................................... 5-40
Cold weather driving
....
........................................................................... 5-40
Battery
....
............................................................................................ 5-41
Engine coolant
....
............................................................................. 5-41
Tire equipment
....
............................................................................. 5-41
Special winter equipment
....
.......................................................... 5-41
Parking brake
....
................................................................................ 5-41
Corrosion protection
....
................................................................... 5-41
GUID-BE06C17C-419B-4EB4-AD19-8D688DDC9C3A
During the first 1,600 km (1,000 miles), follow these
recommendations to obtain maximum engine perfor-
mance and ensure the future reliability and economy of
your new vehicle. Failure to follow these recommenda-
tions may result in shortened engine life and reduced
engine performance.
. Do not drive at a constant speed, either fast or
slow, for long periods of time.
. Do not run the engine over 4,000 rpm (HR12 or
HR15 engine) or 2,500 rpm (K9K engine).
. Do not accelerate at full throttle in any gear.
. Do not start quickly.
. Do not brake hard as much as possible.
GUID-F7E5D977-5816-4216-A489-AC98F4CE6D92
WARNING:
The driving characteristics of your vehicle will
change remarkably by any additional load and
its distribution, as well as by adding optional
equipment (trailer coupling, roof racks, etc.).
Your driving style and speed must be adjusted
according to the circumstances. Especially when
carrying heavy loads, y our speed must be
reduced adequately.
. Make sure the area around the vehicle is clear.
. Visually inspect tires for their appearance and
condition. Measure and check the tire pressure for
proper inflation.
. Check that all windows and lights are clean.
. Adjust the seat and head restraint positions.
. Adjust the inside and outside rearview mirror
positions.
. Fasten your seat belt and ask all passengers to do
the same.
. Check that all doors are closed.
. Check the operation of the warning lights when
the ignition switch is turned to the “ON” position.
. Maintenance items in the “8. Maintenance and do-
it-yourself” section should be checked periodi-
cally.
GUID-B41A6172-5C67 -4B9D-B83F-23644F56F6A3
WARNING:
. Never leave children or adults who would
normally require the support of others alone
in your vehicle. Pets should not be left alone
either. They could unknowingly activate
switches or controls and inadvertently be-
come involved in a serious accident and
injure themselv es . On hot, sunny days,
temperatures in a closed veh icle could
quickly become high enough to cause se-
vere or possibly fatal illness to people or
animals.
. Properly secure all luggage to help prevent it
from sliding or shifting. Do not place lug-
gage higher than the seatbacks. In a sudden
stop or collision, unsecured luggage could
cause personal injury.
EXHAUST GAS (carbon monoxide)
GUID-0830611A-0896-4314-BF19-062754C4851A
WARNING:
. Do not breathe exhaust gas; it contains
colorless and odorless carbon monoxide.
Carbon monoxide is dangerous. It can cause
unconsciousness or death.
. If you suspect that exhaust fumes are
entering the vehicle, drive with all windows
fully open, and have the vehicle inspected
immediately.
. Do not run the engine in closed spaces such
as a garage.
. Do not park the vehicle with the engine
running for an extended period of time.
Starting and driving 5-3
BREAK-IN SCHEDULE BEFORE STARTING ENGINE
PRECAUTIONS WHEN STARTING
AND DRIVING
5-4 Starting and driving
. Keep the back door closed while driving,
otherwise exhaust gas could be drawn into
the passenger compartment. If you must
drive with the back door open, follow these
precautions:
— Open all the windows.
— Turn the air recirculation mode off and
set the fan speed control to the highest
level to circulate the air.
. If electrical wiring or other cable connec-
tions must pass to a trailer through the seal
of the back door or the body, follow the
manufacturer’s recommendation to prevent
carbon monoxide entry into the vehicle.
. If a special body or other equipment is
added for recreational or other usage, follow
the manufacturer’s recommendation to pre-
vent carbon monoxide entry into the vehicle.
(Some recreational vehicle appliances such
as stoves, refrigerators, heaters, etc. may
also generate carbon monoxide.)
. The exhaust system and body should be
inspected by a qualified mechanic whenever:
— Your vehicle is raised while being ser-
viced.
— You suspect that exhaust fumes are
entering into the passenger compart-
ment.
— You notice a change in the sound of the
exhaust system.
— You have had an acciden t involving
damage to the exhaust system, under-
body, or rear of the vehicle.
THREE-WAY CATALYST (gasoline engine
model)
GUID-A7DE8E42-9434-4DA7-ADE4-A0704FD9744D
WARNING:
. The exhaust gas and the exhaust system are
very hot. Keep people, animals and flam-
mab le materials away from the exhaust
system components.
. Do not stop or park the vehicle over
flammable mat erials such as dry grass,
wastepaper or rags. They may ignite and
cause a fire.
The three-way catalyst is an emission control device
installed in the exhaust system. Exhaust gas in the
three-way catalyst is burned at high temperatures to
help reduce pollutants.
CAUTION:
. Do not use leaded gasoline. (See “Recom-
mended fuel/lubricants and capacities” (P.9-
2).) Deposits from leaded gasoline seriously
reduce the ability of the three-way catalyst
to help reduce exhaust pollutants and/or
damage the three-way catalyst.
. Keep your engine tuned up. Malfunctions in
the ignition, fuel injection, or electrical
systems may cause overrich fuel to flow into
the three-way catalyst, causing it to over-
heat. Do not keep driving if the engine
misfires, or if noticeable loss of performance
or other unusual operating conditions are
detected. Have the vehicle inspected
promptly by a NISSAN dealer.
. Avoid driving with an extremely low fuel
level. Running out of fuel could cause the
engine to misfire, damaging the three-way
catalyst.
. Do not race the engine while warming it up.
. Do not push or tow your vehicle to start the
engine.
GUID-F8498E1E-7260-4875-BC2A-1D6C8CB65F20
Driving your vehicle to fit the circumstances is essential
for your safety and comfort. As a driver, you should be
the one who knows best how to drive in the given
circumstances.
ENGINE COLD START PERIOD
GUID-433AD7F9-C51C-4491-9497-AC23333C3B08
Due to the higher engine speeds, when the engine is
cold, extra caution must be exercised when selecting a
gear during the engine warm-up period after starting
the engine.
LOADING LUGGAGE
GUID-06EE7FD2-DD9B-48AD-AD9E-F9760691A0A2
Loads and their distribution and the attachment of
equipment (coupling devices, roof baggage carriers,
etc.) will considerably change the driving character-
istics of the vehicle. Your driving style and speed must
be adjusted according to the circumstances.
DRIVING IN WET CONDITIONS
GUID-07E1741E-BE6 9-40CF-AB0A-7193914F0198
. Avoid accelerating or stopping suddenly.
. Avoid sharp turning or lane changing suddenly.
. Avoid following too close to the vehicle in front.
When water cov ers the road surface with water
puddles, small water streams, etc., reduce speed to
prevent hydroplaning which can cause skidding and
loss of control. Worn tires will increase this risk.
DRIVING IN WINTER CONDITIONS
GUID-55AE4C54-BBAA-4239-AC0E-368FA0BE987D
. Drive cautiously.
. Avoid accelerating or stopping suddenly.
. Avoid sharp turning or lane changing suddenly.
. Avoid sudden steering.
. Avoid following too close to the vehicle in front.
GUID-11BE66E7-9D1B-4D19-8C54-69B15542917F
WARNING:
Never remove the key or turn the ignition switch
to the “LOCK” position while driving. The steer-
ing wheel will lock. This may cause the driver to
lose control of the vehicle and could result in
serious vehicle damage or personal injury.
AUTOMATIC TRANSMISSION (AT)/CON-
TINUOUSLY VARIABLE TRANSMISSION
(CVT)
GUID-E6B359FC-5408-4ECB-87F0-5A309167AA89
SSD0392
The ignition lock is designed so that the ignition switch
cannot be turned to the “LOCK” position until the shift
lever is moved to the “P” (Park) position. When moving
the ignition switch to the “LOCK” position, to remove
the key from the ignition switch, make sure the shift
lever is in the “P” (Park) position.
When the ignition switch cannot be turned to the
“LOCK” position:
1. Move the shift lever to the “P” (Park) position.
2. Turn the igniti on switch slightly in the “ON”
direction.
3. Turn the ignition switch to the “LOCK” position.
4. Remove the key, if it is inserted in the ignition
switch.
If the ignition switch is turned to the “LOCK” position,
the shift lever cannot be moved from the “P” (Park)
position. The shift lever can be moved if the ignition
switch is in the “ON” position with the foot brake pedal
depressed.
The “OFF” position
*
1
is between the “LOCK” and
“ACC” positions, although it is not marked on the
ignition switch.
MANUAL TRANSMISSION (MT)
GUID-7A409D94-0BAB-478E-99B6-6BF9196E36BD
SSD0392
Type A
Starting and driving 5-5
CARE WHEN DRIVING
IGNITION SWITCH (model without
intelligent Key system)
5-6 Starting and driving
SSD0503
Type B
The ignitio n switch includes a device that helps
prevent accidental removal of the key while driving.
The key can only be removed when the ignition switch
is in the “LOCK” position.
Type B: To turn the ignition switch to the “LOCK”
position from the “ACC” or “ON” position, turn the key
to the “OFF” position, push the key in, then turn the key
to the “LOCK” position.
The “OFF” position
*
1
is between the “LOCK” and
“ACC” positions, although it is not labeled on the
ignition switch.
STEERING LOCK
GUID-B79D811B-DB48-49A4-B0EE-34D13EDCA340
To lock steering wheel
GUID-FCFEB02B-943D-4686-A4B0-CA3E9D810A64
1. Turn the ignition switch to the “LOCK” position.
2. Remove the key.
3. Turn the steering wheel 1/6 of a turn clockwise
from the straight up position.
To unlock steering wheel
GUID-A743404E-356D-4293-8839-A4BD9EE6DB46
1. Insert the key into the ignition switch.
2. Gently turn the ignition switch while rotating the
steering wheel slightly right and left.
KEY POSITIONS
GUID-F9297A75-F084-4D72-A37F-A21E15C6928D
LOCK (0)
GUID-6C6B58B5-E98F-4E68-8234-88630D5BEB94
The ignition key can only be removed at this position.
The steering lock can only be locked at this position.
OFF (1)
GUID-711951C6-01CE-4BAA-A2A9-C22DF515B2E5
The engine is turned off with the steering wheel
unlocked.
ACC (2)
GUID-C6EAC595-9B36-41EB-BB71-8F344CD57839
The electrical accessory power activates without the
engine turned on.
ON (3)
GUID-7F2FB7AD-8580-462C-A2FC-44540A7340EA
The ignition system and the electrical accessory power
activate without the engine turned on.
START (4)
GUID-943AD409-77BB-4E96-B225-F98803755435
The engine starter activates and the engine will start.
The ignition switch, when released, will automatically
turn to the “ON” position.
CAUTION:
As soon as the engine has started, release the
ignition switch immediately.
GUID-5106BE37-098B-4B70-8AF0-F80991A1C9D6
PRECAUTIONS ON PUSH-BUTTON IGNI-
TION SWITCH OPERATION
GUID-39123703-340D-4CBF-8909-71DDE48C4BE8
WARNING:
Do not operate the push-button ignition switch
while driving the vehicle except in an emergency.
(The engine will stop when the ignition switch is
pushed 3 consecutive times or the ignition
switch is pushed and held for more than 2
seconds.) The steering wheel will lock and could
cause the driver to lose control of the vehicle.
This could result in serious vehicle damage or
personal injury.
Before operating the push-button ignition switch, be
sure to move the shift lever to the “P” (Park) position
(for Automatic Transmission/Continuou sly Variab le
Transmission model) or the shift lever to the “N”
(Neutral) position (for Manual Transmission model).
INTELLIGENT KEY SYSTEM
GUID-D9A723C7-B5AF-4D6A-BF11-749DB3C059F1
The Intelligent Key system can operate the ignition
switch without taking the key out from your pocket or
bag. The operating environment and/or conditions may
affect the Intellige n t Key system operation. Some
indicators and warnings for operation are displayed
on the vehicle information display (if equipped) and/or
in the meter. (See “Vehicle information display” (P.2-
20) and “Warning/indicator lights and audible remin-
ders” (P.2-12).)
CAUTION:
. Be sure to carry the Intelligent Key with you
when operating the vehicle.
. Never leave the Intelligent Key inside the
vehicle when you leave the vehicle.
PUSH-BUTTON IGNITION SWITCH
(model with Intelligent Key system)
. If the vehicle battery is disch arged, the
ignitio n switch cannot be switched from
the “LOCK” position, and if the steering lock
is engaged, the steering wheel cannot be
moved. Charge the battery as soon as
possible. (See “Jump starting” (P.6-9).)
Operating range
GUID-46C0E5E9-CA13-4ED3-9349-A70E14CFB689
SSD0436
The Intelligent Key can only be used for starting the
engine when the Intelligent Key is within the specified
operating range
*
1
.
When the Intelligent Key battery is almost discharged
or strong radio waves are present near the operating
location, the Intelligent Key system’s operating range
becomes narrower and may not function properly.
If the Intelligent Key is within the operating range, it is
possible for anyone, even someone who does not carry
the Intelligent Key, to push the ignition switch to start
the engine.
. The luggage room area is not included in the
operating range, but the Intelligent Key may
function.
. If the Intelligent Key is placed on the instrument
panel, inside the glove box, door pocket or the
corner of the interior compartment, the Intelligent
Key may not function.
. If the Intelligent Key is placed near the door or
window outside the vehicle, the Intelligent Key
may function.
Automatic transmission (AT)/Continuously
Variable Transmission (CVT) model
GUID-957EB82F-1A5E-4B31-B269-3BA742F81C13
The ignition lock is designed so that the ignition switch
cannot be switched to the “LOCK” position until the
shift lever is moved to the “P” (Park) position. When
pushing the ignition switch to the “OFF” position, make
sure the shift lever is in the “P” (Park) position.
Type A (model with dot matrix display):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
When the ignition switch cannot be switched to the
“LOCK” position:
1. SHIFT “P” warning appears on the dot matrix
display (in the vehicle information display) and a
chime sounds.
2. Move the shift lever to the “P” (Park) position.
3. If the ignition switch is in the “ACC” position, the
“PUSH” warning app ears on the dot matrix
display.
4. Push the ignition switch. The ignition switch is
switched to the “ON” position.
5. The “PUSH” warning appears again on the dot
matrix display.
6. Push the ignition switch. The ignition switch is
switched to the “OFF” position.
7. Open the door. The ignition switch will change to
the “LOCK” position.
For warnings and indicators on the Vehicle information
display, see “Vehicle information display” (P.2-20).
Type B (model without dot matrix display):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
1. Move the shift lever to the “P” (Park) position.
2. Push the ignition switch to the “OFF” position.
3. Open the door. The ignition switch will change to
the “LOCK” position.
If the ignition switch is switched to the “LOCK”
position, the shift lever cannot be moved from the “P”
(Park) position. The shift lever can be moved if the
ignition switch is in the “ON” position with the foot
brake depressed.
STEERING LOCK
GUID-2F58254E-F7F8-483C-94EB-A4433CF3D958
The ignition switch is equipped with an anti-theft
steering lock device.
To lock steering wheel
GUID-EEEBBE44-96AA-4552-989C-C8364A16DAAC
1. Push the ignition switch to the “OFF” position
where the ignition switch position indicator will not
illuminate.
2. Open or close the door. The ignition switch turns
to the “LOCK” position.
3. Turn the steering wheel 1/6 of a turn to the right or
left from the straight up position.
To unlock steering wheel
GUID-E7243AC8-9F32-4B57-88C4-9F4592DA19D0
Push the ignition switch, and the steering wheel will be
automatically unlocked.
CAUTION:
. If the battery of the vehicle is discharged, the
push-button ignition sw itch cannot be
switched from the “LOCK” position.
. If the ignition switch position does not
change from the “LOCK” position, push the
ignition switch again while rotating the
Starting and driving 5-7
5-8 Starting and driving
steering wheel slightly to the right and left.
(See “Vehicle information display” (P.2-20).)
IGNITION SWITCH POSITIONS
GUID-DD6A28B5-3A18-48D7-B6C0-6C80DD89B09D
SSD0859
When the ignition switch is pushed without depressing
the brake pedal (Automatic Transmission/Continuously
Variable Transmission model) or the clutch pedal
(Manual Transmission model), the ignition switch
position will change as follows:
. Push once to change to “ACC”.
. Push two times to change to “ON”.
. Push three times to change to “OFF”.
. Push four times to return to “ACC”.
. Open or close any door to return to “LOCK” when
in the “OFF” position.
The indicator light
*
A
on the ignition switch illumi-
nates when the ignition switch is in the “ACC” or “ON”
position.
LOCK position
GUID-C1277B7B-AB1A-4 763-9CCE-D787592BC7B5
The ignition switch and steering lock can only be
locked at this position.
The ignition switch will be unlocked when it is pushed
to the “ACC” position while carrying the Intelligent Key.
ACC position
GUID-2A707D02-1676-4BC4-ABD1-C6A371D6ECB3
The electrical accessory power activates at this
position without the engine turned on.
ON position
GUID-D2BC5C1D-79B 3-4B54-A5A3-512B8F951FC2
The ignition system and the electrical accessory power
activate at this position without the engine turned on.
OFF position
GUID-C919DC62-9BD4-432C-815A-E2497AFC659D
The engine is turned off with the steering wheel
unlocked.
WARNING:
Never push the ignition switch to the “OFF”
position while driving. The steering wheel may
lock and cause the driver to lose control of the
vehicle, resulting in serious vehicle damage or
personal injury.
CAUTION:
Do not leave the vehicle for extended periods of
time when the ignition switch is in the “ACC” or
“ON” position and the engine is not running.
This can discharge the battery.
NOTE:
When the ignition switch is pushed while the
Stop/Start (Idling Stop) System (if equipped) is
activated, the ignition switch will be placed in
the "OFF" position.
INTELLIGENT KEY BATTERY DISCHARGE
GUID-E439BD31-542C-4C76-868F-7B5005FB3FAF
SSD0860
If the battery of the Intelligent Key is discharged, or
environmental conditions interfere with the Intelligent
Key operation, start the engine accord ing to the
following procedure:
1. Automatic Transmission (AT)/Continuously
Variable Transmission (CVT) model:
Move the shift lever to the “P” (Park) or “N”
(Neutral) position.
Manual Transmission (MT) model:
Move the shift lever to the “N” (Neutral) position.
2. Firmly depress the brake pedal (Automatic Trans-
mission/Continuously Variable Transmission mod-
el) or the clutch pedal (Manual Transmission
model).
3. Touch the ignition switch with the Intelligent Key
as illustrated. (A chime will sound.)
4. Push the ignition switch while depressing the
brake pedal within 10 seconds after the chime
sounds. The engine will start.
After step 3 is performed, when the ignition switch is
pushed without depressing the brake peda l, the
ignition switch position will change to “ACC”.
NOTE:
. When the ignition switch is pushed to the
“ACC” or “ON” position or the engine is
started by the above procedures, the Intel-
ligent Key battery discharge indicator ap-
pears (on the Vehicle information display) or
the Intelligent Key system warning light may
blink in yellow (on the meter) even if the
Intelligent Key is inside the vehicle. This is
not a malfunction. To stop the warning light
from blinking, touch the ignition switch with
the Intelligent Key again.
. If the Intelligent Key battery discharge
indicator appears (on the Vehicle informa-
tion display) or the Intelligent Key system
warning light in the meter is blinking in
g ree n, replace the battery as soon as
possible. (See “Battery” (P.8-24).)
GUID-F3C623BE-87A8-45E1-84D8-1ACC85B1F10F
GASOLINE ENGINE
GUID-1FCDE0B8-5394-4508-841F-302493AACAA5
1. Apply the parking brake.
2. Depress the foot brake pedal.
3. Automatic Transmission (AT)/Continuously
Variable Transmission (CVT) model:
Move the shift lever to the “P” (Park) or “N”
(Neutral) position.
The starter is designed to operate only when
the shift lever is in the proper position.
Manual Transmission (MT) model:
Move the shift lever to the “N” (Neutral) position,
and depress the clutch pedal to the floor while
starting the engine.
The starter is designed to not operate unless
the clutch pedal is depressed.
4. Crank the engine with your foot off the accelerator
pedal by turning the ignition switch to the “START”
position.
5. Immediately release the ignition switch when the
engine starts. If the engine starts, but fails to run,
repeat the above procedures.
If the engine is very hard to start in extremely cold
or hot weather, depress the accelerator pedal and
hold it to help start the engine.
CAUTION:
. Do not operate the starter for more than 15
seconds at a time. If the engine does not
start, turn the ignition switch off and wait 10
seconds before cranking the engine again.
Otherwise, the starter could be damaged.
. If it becomes necessary to start the engine
with a booster battery and jumper cables,
the instructions and cautions contained in
the “6. In case of emergency” section should
be carefully followed.
6. Allow the engine to idle for at least 30 seconds
after starting the engine to warm-up. Drive at
moderate speeds for a short dis tance first,
especially in cold weather.
CAUTION:
Do not leave the vehicle unattended while the
engine is warming up.
DIESEL ENGINE
GUID-A6AEE369-FE83-4D6D-82D2-BF95CCACE180
1. Apply the parking brake.
2. Depress the foot brake pedal.
3. Move the shift lever to the “N” (Neutral) position,
and depress the clutch pedal to the floor while
starting the engine.
4. Turn the ignition switch to the “ON” position and
wait until the glow plug indicator light
turns
off.
5. Crank the engine with your foot off the accelerator
pedal by turning the ignition switch to the “START”
position.
6. Immediately release the ignition switch when the
engine starts. If the engine starts, but fails to run,
repeat the above procedures.
CAUTION:
. Do not operate the starter for more than 20
seconds at a time. If the engine does not
start, turn the ignition switch off and wait 20
seconds before cranking the engine again.
Otherwise, the starter could be damaged.
Starting and driving 5-9
STARTING ENGINE (model without
Intelligent Key system)
5-10 Starting and driving
. If it becomes necessary to start the engine
with a booster battery and jumper cables,
the instructions and cautions contained in
the “6. In case of emergency” section should
be carefully followed.
7. Allow the engine to idle for at least 30 seconds
after starting the engine to warm-up. Drive at
moderate speeds for a short dis tance first,
especially in cold weather.
CAUTION:
Do not leave the vehicle unattended while the
engine is warming up.
GUID-550B631B-68A2-4F99-A948-04AAF8C3D969
GASOLINE ENGINE
GUID-EAD13246-6BD8-48E1-AC5E-0F549108B776
1. Apply the parking brake.
2. Automatic Transmission (AT)/Continuously
Variable Transmission (CVT) model:
Move the shift lever to the “P” (Park) or the “N”
(Neutral) position.
The starter is designed to operate only when
the shift lever is in the proper position.
Manual Transmission (MT) model:
Move the shift lever to the “N” (Neutral) position.
The starter is designed to not operate unless
the clutch pedal is fully depressed.
The Intelligent Key must be carried when
operating the ignition switch.
3. Push the ignition switch to the “ON” position.
Depress the brake pedal (AT/CVT model) or the
clutch pedal (MT model) and push the ignition
switch to start the engine.
To start the engine immediately, push and release
the ignition switch while depressing the brake
pedal or clutch pedal with the ignition switch in
any position.
4. Immediately release the ignition switch when the
engine starts. If the engine starts, but fails to run,
repeat the above procedures.
If the engine is very hard to start in extremely cold
or hot weather, depress the accelerator pedal and
hold it. Push the ignition switch for up to 15
seconds while holding. Release the accelerator
pedal when the engine starts.
CAUTION:
. As soon as the engine has started, release
the ignition switch immediately.
. Do not operate the starter for more than 15
seconds at a time. If the engine does not
start, push the ignition switch to the “OFF”
position and wait 10 seconds before crank-
ing the engine again. Otherwise, the starter
could be damaged.
. If it becomes necessary to start the engine
with a booster battery and jumper cables,
the instructions and cautions contained in
the “6. In case of emergency” section should
be carefully followed.
5. Allow the engine to idle for at least 30 seconds
after starting the engine to warm-up. Drive at
moderate speeds for a short dis tance first,
especially in cold weather.
CAUTION:
Do not leave the vehicle unattended while the
engine is warming up.
6. To stop the engine, move the shift lever to the “P”
(Park) position (AT/CVT model) or move the shift
lever to the “N” (Neutral) position (MT model),
apply the parking brake and push the ignition
switch to the “OFF” position.
STARTING ENGINE (model with
Intelligent Key system)
DIESEL ENGINE
GUID-AA26359D-8901-44E8-AFB1-AB2B2EB2C91F
1. Apply the parking brake.
2. Move the shift lever to the “N” (Neutral) position.
The starter is designed to not operate unless
the clutch pedal is fully depressed.
The Intelligent Key must be carried when
operating the ignition switch.
3. Push the ignition switch to the “ON” position and
wait until the glow plug indicator light turns off.
Depress the clutch pedal and push the ignition
switch to start the engine.
To start the engine immediately, push and release
the ignition switch while depressing the clutch
pedal with the ignition switch in any position.
4. Immediately release the ignition switch when the
engine starts. If the engine starts, but fails to run,
repeat the above procedures.
If the engine is very hard to start in extremely cold
or hot weather, depress the accelerator pedal and
hold it. Push the ignition switch for up to 15
seconds while holding. Release the accelerator
pedal when the engine starts.
CAUTION:
. As soon as the engine has started, release
the ignition switch immediately.
. Do not operate the starter for more than 20
seconds at a time. If the engine does not
start, push the ignition switch to the “OFF”
position and wait 20 seconds before crank-
ing the engine again. Otherwise, the starter
could be damaged.
. If it becomes necessary to start the engine
with a booster battery and jumper cables,
the instructions and cautions contained in
the “6. In case of emergency” section should
be carefully followed.
5. Allow the engine to idle for at least 30 seconds
after starting the engine to warm-up. Drive at
moderate speeds for a short dis tance first,
especially in cold weather.
CAUTION:
Do not leave the vehicle unattended while the
engine is warming up.
6. To stop the engine, move the shift lever to the “N”
(Neutral) position, apply the parking brake and
push the ignition switch to the “OFF” position.
GUID-ED2CE400-2959-47E0-929D-D3D4E0A10EEC
DRIVING WITH AUTOMATIC TRANSMIS-
SION (AT)
GUID-826D4175-8658-4B2C-BE5F-EBD4979CFB5F
The Automatic Transmission (AT) in your vehicle is
electronically controlled to produce maximum power
and smooth operation.
The recomm ended operating procedures fo r th is
transmission are shown on the following pages. Follow
these procedures for maximum vehicle performance
and driving enjoyment.
WARNING:
Do not downshift abruptly on slippery roads.
This may cause a loss of control.
CAUTION:
. The cold engine idle speed is high, so use
caution when shifting the transmission into
a forward or reverse position before the
engine has warmed up.
. Avoid revving up the engine while the
vehicle is stopped. This could cause unex-
pected vehicle movement.
. Never shift to either the “P” (Park) or “R”
(Reverse) position while the vehicle is mov-
ing. This could cause serious damage to the
transmission.
. Except in an emergency, do not shift to the
“N” (Neutral) position while driving. Coast-
ing with the transmission in the “N” (Neutral)
position may cause serious damage to the
transmission.
. Start the engine in either the “P” (Park) or
“N” (Neutral) position. The engine will not
start in any other position. If it does, have
Starting and driving 5-11
DRIVING VEHICLE
5-12 Starting and driving
your vehicle checked by a NISSAN dealer.
. Shift into the “P” (Park) position and apply
the parking brake when at a standstill for
longer than a short waiting period.
. Keep the engine at idlin g speed while
shifting from the “N” (Neutral) position to
any driving position.
. When stopping the vehicle on an uphill
grade, do not hold the vehicle by depressing
the accelerator pedal. The foot brake pedal
should be depressed in this situation.
Starting vehicle
GUID-A34F1624-34DA-4CC6-A351-F7663BEA2BEF
1. After starting the engine, fully depress the foot
brake pedal before shifting the shift lever out of the
“P” (Park) position.
2. Keep the foot brake pedal depressed and move
the shift lever to a driving position.
3. Release the parking brake, the foot brake pedal,
and then gradually start the vehicle in motion.
The AT is designed so the foot brake pedal
MUST be depressed before shifting from the “P”
(Park) position to any driving position while the
ignition switch is in the “ON” position.
The shift lever cannot be moved out of the “P”
(Park) position and into any of the other gear
positions if the ignition switch is turned to the
“LOCK”, “OFF” or “ACC” position or if the key is
removed.
CAUTION:
. DEPRESS THE FOOT BRAKE PEDAL - Shift-
ing the shift lever to “D”, “R”, “2” or “1”
without depressing the fo ot brake pedal
causes the vehicle to move slowly when
the engine is running. Make sure the foot
brake pedal is depressed fully and the
vehicle is stopped before shifting the shift
lever.
. MAKE SURE OF THE SHIFT LEVER POSI-
TION - Make sure the shift lever is in the
desired position. “D”, “2” and “1” are used to
move forward and “R” to back up.
. WARM UP THE ENGINE - Due to the higher
idle speeds when the engine is cold, extra
caution must be exercised when shifting the
shift lever into the driving position immedi-
ately after starting the engine.
Shifting gear
GUID-5C3474C3-9514 -4881-80AE-66E36F66FBD4
JVS0008X
Left-Hand Drive (LHD) model
JVS0009X
Right-Hand Drive (RHD) model
: Push the button
*
A
while depressing the
foot brake pedal.
: Push the button
*
A
.
: Just move the shift lever.
WARNING:
. Apply the parking brake if the shift lever is in
any position while the engine is not running.
Failure to do so could cause the vehicle to
move unexpectedly or roll away and result in
serious personal injury or property damage.
. If the shift lever cannot be moved from the P
(Park) position while the engine is running
and the foot brake pedal is depressed, the
stop lights may not work. Malfunctioning
stop lights could cause an accident injuring
yourself and others.
After starting the engine, fully depress the foot brake
pedal, push the shift lever button and move the shift
lever out of the P (Park) position.
If the ignition switch is the OFF or ACC position for any
reason while the shift lever is in any positions other
than the P (Park) position, the ignition switch cannot
be turned to the LOCK position.
If the ignition switch cannot be the LOCK position,
perform the following steps:
1. Apply the parking brake.
2. Place the ignition switch in the ON position while
depressing the foot brake pedal.
3. Move the shift lever to the P (Park) position.
4. Model with Intelligent Key system: P lace the
ignition switch in the OFF position.
Model without Intelligent Key system: Place the
ignition switch in the LOCK position.
P (Park):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Use this position when the vehicle is parked or when
starting the engine. Make sure that the vehicle is
completely stopped and move the shift lever into
the P (Park) position. Apply the parking brake.
When parking on a hill, apply the parking brake first,
and then move the shift lever into the P (Park) position.
R (Reverse):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Use this position to back up. Make sure that the vehicle
is completely stopped before selecting the R (Reverse)
position.
N (Neutral):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Neither the forward nor reverse gear is engaged. The
engine can be started in this position. You may shift to
the N (Neutral) position and restart a stalled engine
while the vehicle is moving.
D (Drive):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Use this position for all normal forward driving.
2 (Second gear):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Use this position for climbing hills or engine braking on
downhill grades.
1 (Low gear):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Use this position when climbing steep hills slowly or
driving slowly through deep snow, or for maximum
engine braking on steep downhill grades.
Do not shift into the gears when the vehicle speed
exceeds the following limits, otherwise the engine may
over-rev and cause engine damage.
Engine model
Shift lever position
1 2
HR12DE
km/h (MPH)
45 (28) 90 (56)
HR15DE
km/h (MPH)
50 (30)
95 (60)
Overdrive switch
GUID-7D0E15F2-00D5-43C2-BC45-EA894A6F5D44
JVS0013X
Left-Hand Drive (LHD) model
Each time the engine is started, the overdrive function
is automatically reset to “ON”.
“ON” position:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
With the engine running and the shift lever in the “D”
(Drive) position, the transmission upshifts into the
overdrive as vehicle speed increases.
Overdrive does not engage until the engine has
reached operating temperature.
“OFF” position:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
For driving up and down long slopes where engine
braking is necessary, push the overdrive switch. The
overdrive off indicator light
in the meter panel
illuminates.
When cruising at a low speed or climbing a gentle
slope, you may feel uncomfortable shift shocks as the
transmission shifts i nto and out of the overdrive
repeatedly. In this case, push the overdrive switch to
turn the overdrive “OFF”.
When driving conditions change, push the overdrive
switch to turn the overdrive “ON”. The overdrive off
indicator light will turn off.
Remember not to drive at high speeds for extended
periods of time with the overdrive “OFF”. This reduces
fuel economy.
Accelerator downshift - in D (Drive) position
GUID-9A4FB4A2-7ADC-4D2B-AC49-9E990E768116
For passing or climbing hills, depress the accelerator
pedal to the floor. This shifts the transmission down
into a lower gear, depending on the vehicle speed.
Shift lock release
GUID-C5669C84-95D6-4B8C-85A8-3C7D02F9B4DD
If the battery is discharged, the shift lever may not be
moved from the “P” (Park) position even with the foot
brake pedal depressed.
To move the shift lever, release the shift lock. The shift
lever can be moved to the “N” (Neutral) position.
However, the steering wheel will be locked unless the
ignition switch is placed in the “ON” position. This
Starting and driving 5-13
5-14 Starting and driving
allows the vehicle to be moved if the battery is
discharged.
JVS0014X
Right-Hand Drive (RHD) model
To release the shift lock, perform the following
procedure
1. Models with Intelligent KEY system: Place the
ignition switch in the “OFF” or “LOCK” position.
Models without Intelligent KEY system: Place the
ignition switch in the “LOCK” position and remove
the key.
2. Apply the parking brake.
3. Depress the shift lock release button.
4. Push and hold the shift lever button and move the
shift lever to the “N” (Neutral) position while
holding down the shift lock release button.
5. Place the ignition switch to the “ON” position to
release the steering wheel lock.
The vehicle may be moved, by pushing, to the desired
location.
If the shift lever cannot be moved out of the “P” (Park)
position, have a NISSAN dealer check the AT system
as soon as possible.
Fail-safe
GUID-70726E5E-F30C-457F-B628-89E1EE84479B
When the fail-safe operation occurs, the AT will be
locked in third gear.
If the vehicle is driven under extreme conditions,
such as excessive wheel spinning and subse-
quent hard braking, the fail-safe system may be
activated. This will occur even if all electrical
circuits are functioning properly. In this case,
turn the ignition switch off and wait for 3
seconds. Then turn the ignition switch back to
the “ON” position. The vehicle should return to
its normal operating condition. If it does not
return to its normal operating condition, have a
NISSAN dealer check the transmission and
repair it if necessary.
DRIVING WITH CONTINUOUSLY VARI-
ABLE TRANSMISSION (CVT)
GUID-7DB33ED5-E1E C-4DC7-9D8A-BB857680DFD7
The Continuously Variable Transmission (CVT) in your
vehicle is electronically controlled to produce maximum
power and smooth operation.
The recomm ended operating procedures fo r th is
transmission are shown on the following pages. Follow
these procedures for maximum vehicle performance
and driving enjoyment.
WARNING:
Do not downshift abruptly on slippery roads.
This may cause a loss of control.
CAUTION:
. The cold engine idle speed is high, so use
caution when shifting the transmission into
a forward or reverse position before the
engine has warmed up.
. Avoid revving up the engine while the
vehicle is stopped. This could cause unex-
pected vehicle movement.
. Never shift to either the “P” (Park) or “R”
(Reverse) position while the vehicle is mov-
ing. This could cause serious damage to the
transmission.
. Except in an emergency, do not shift to the
“N” (Neutral) position while driving. Coast-
ing with the transmission in the “N” (Neutral)
position may cause serious damage to the
transmission.
. Start the engine in either the “P” (Park) or
“N” (Neutral) position. The engine will not
start in any other position. If it does, have
your vehicle checked by a NISSAN dealer.
. Shift into the “P” (Park) position and apply
the parking brake when at a standstill for
longer than a short waiting period.
. Keep the engine at idlin g speed while
shifting from the “N” (Neutral) position to
any driving position.
. When stopping the vehicle on an uphill
grade, do not hold the vehicle by depressing
the accelerator pedal. The foot brake pedal
should be depressed in this situation.
Starting vehicle
GUID-10830AE3-53E9-4C49-8A46-50D0BF37D1E3
1. After starting the engine, fully depress the foot
brake pedal before moving the shift lever out of the
“P” (Park) position.
2. Keep the foot brake pedal depressed and move
the shift lever to a driving position.
3. Release the parking brake, the foot brake pedal,
and then gradually start the vehicle in motion.
The CVT is designed so the foot brake pedal
MUST be depressed before shifting from the “P”
(Park) position to any driving position while the
ignition switch is in the “ON” position.
The shift lever cannot be moved out of the “P”
(Park) position and into any of the other
positions if the ignition switch is placed in the
“LOCK”, “OFF” or “ACC” position or if the key is
removed.
CAUTION:
. DEPRESS THE FOOT BRAKE PEDAL - Shift-
ing the shift lever to “D”, “R” or “L” without
depressing the foot brake pedal causes the
vehicle to move slowly when the engine is
running. Make sure the foot brake pedal is
depressed fully and the vehicle is stopped
before shifting the shift lever.
. MAKE SURE OF THE SHIFT LEVER POSI-
TION - Make sure the shift lever is in the
desired position. “D” and “L” are used to
move forward and “R” to back up.
. WARM UP THE ENGINE - Due to the higher
idle speeds when the engine is cold, extra
caution must be exercised when shifting the
shift lever into the driving position immedi-
ately after starting the engine.
JVS0011X
Left-Hand Drive (LHD) model
JVC0026X
Right-Hand Drive (RHD) model
: Push the button
*
A
while depressing the
foot brake pedal.
: Push the button
*
A
.
: Just move the shift lever.
Shifting
GUID-F0518EC1-210F-4737-A790-667D7F0C6B65
WARNING:
. Apply the parking brake if the shift lever is in
any position while the engine is not running.
Failure to do so could cause the vehicle to
move unexpectedly or roll away and result in
serious personal injury or property damage.
. If the shift lever cannot be moved from the
“P” (Park) position while the engine is
running and the foot brake pedal is de-
pressed, the stop lights may not work.
Malfunctioning stop lights could cause an
accident injuring yourself and others.
After starting the engine, fully depress the foot brake
pedal, push the shift lever button and move the shift
lever out of the “P” (Park) position.
If the ignition switch is placed in the “OFF” or “ACC”
position for any reason while the shift lever is in any
positions other than the “P” (Park) position, the ignition
switch cannot be placed in the “LOCK” position.
If the ignition switch cannot be placed in the “LOCK”
position, perform the following steps:
1. Apply the parking brake.
2. Place the ignition switch in the “ON” position
while depressing the foot brake pedal.
3. Move the shift lever to the “P” (Park) position.
4. Models with Intelligent Key system:
Place the ignition switch in the “OFF” position.
Models without Intelligent Key system:
Place the ignition switch in the “LOCK” position.
Starting and driving 5-15
5-16 Starting and driving
P (Park):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Use this position when the vehicle is parked or when
starting the engine. Make sure that the vehicle is
completely stopped and move the shift lever into
the “P” (Park) position. Apply the parking brake.
When parking on a hill, first depress the foot brake
pedal, apply the parking brake, and then move the shift
lever into the “P” (Park) position.
R (Reverse):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Use this position to back up. Make sure that the vehicle
is compl etely stopped before sel ecting the “R”
(Reverse) position.
N (Neutral):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Neither the forward nor reverse gear is engaged. The
engine can be started in this position. You may shift to
the “N” (Neutral) position and restart a stalled engine
while the vehicle is moving.
D (Drive):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Use this position for all normal forward driving.
L (Low):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Use this position when climbing steep hills slowly or
driving slowly through deep snow, sand or mud, or for
maximum engine braking on steep downhill grades.
SPORT mode switch
GUID-831EB3E0-330F-44E6-9E2A-935D870A1FD9
JVC0027X
Right-Hand Drive (RHD) model
To select the SPORT mode, push the SPORT mode
switch with the shift lever in the “D” (Drive) position.
The SPORT mode indicator light
in the meter
panel illuminates. To turn off the SPORT mode, push
the SPORT mode switch again. The SPORT mode
indicator light will turn off. When the shift lever is
shifted to any position other than “D”, the SPORT
mode will be automatically turned off.
“OFF” position:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
For normal driving and fuel economy, use the “OFF”
position.
“ON” position:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
For driving up or down long slopes where engine
braking is necessary, or for powerful acceleration, use
the “ON” position. The transmission will automatically
select a different gear ratio, allowing the engine to
provide high output.
When driving conditions change, push the switch to
turn the SPORT mode off.
Remember not to drive at high speeds for extended
periods of time with the SPORT mode in the “ON”
position. This reduces fuel economy.
Accelerator downshift - in the “D” position -
GUID-1B271593-A574-4815-9738-00C74E37A056
For passing or climbing hills, depress the accelerator
pedal to the floor. This shifts the transmission down
into a lower gear, depending on the vehicle speed.
Shift lock release
GUID-087771B9-AE5C-4 7DB-A6F2-CA2DF8F7C0E5
JVC0028X
Right-Hand Drive (RHD) model
If the battery charge is low or discharged, the shift
lever may not be moved from the “P” (Park) position
even with the brake pedal depressed and the shift lever
button pushed.
To move t he shift lever, perform the following
procedure:
1. Model with Intelligent Key system:
Place the ignition switch in the “OFF” or “LOCK”
position.
Model without Intelligent Key system:
Place the ignition switch in the “LOCK” position,
and remove the key if it is inserted.
2. Apply the parking brake.
3. Depress the shift lock release button.
4. Push the shift lever button and move the shift lever
to the “N” (Neutral) position while holding down
the shift lock release.
5. Place the ignition switch in the “ON” position to
unlock the steering wheel.
The vehicle may be moved to the desired location.
Replace the removed shift lock release cover after the
operation.
For model with Intelligent Key system: If the battery is
discharged completely, the steering wheel cannot be
unlocked. Do not move the vehicle with the steering
wheel locked.
If the shift lever cannot be moved out of the “P” (Park)
position, have a NISSAN dealer check the CVT system
as soon as possible.
WARNING:
If the shift lever cannot be moved from the “P”
(Park) position while the engine is running and
the brake pedal is depressed, the stop lights
may not work. Malfunctioning stop lights could
cause an accident injuring yourself and others.
High fluid temperature protection mode
GUID-72D69A4F-20 B1-4A4F-A0B0-A340C8ABB77F
This transmission has a high fluid temperature protec-
tion mode. If the fluid temperature becomes too high
(for example, when climbing steep grades in high
temperature with heavy loads, such as when towing a
trailer), engine power and, under some conditions,
vehicl e speed will be decreased automatically to
reduce the chance of transmission damage. Vehicle
speed can be controlled with the accelerator pedal,
but engine and vehicle speed may be limited.
Fail-safe
GUID-FE30EFD6-3B41-4747-8ECD-CD8D5D3FE6BC
When the fail-safe operation occurs, the CVT will not
be shifted to the selected driving position.
If the vehicle is driven under extreme conditions,
such as excessive wheel spinning and subse-
quent hard braking, the fail-safe system may be
activated. This will occur even if all electrical
circuits are functioning properly. In this case,
place the ignition switch in the “OFF” position
and wait for 10 seconds. Then turn the ignition
switch back to the “ON” position. The vehicle
should return to its normal operating condition.
If it does not return to its normal operating
condition, have a NISSAN dealer check the
transmission and repair it if necessary.
WARNING:
When the fail-safe operation occ urs, vehicle
speed may be gradually reduced. The reduced
speed may be lower than other traffic, which
could increase the chance of a collision. Be
especially careful when driving. If necessary, pull
to the side of the road at a safe place and allow
the transmission to return to normal operation,
or have it repaired if necessary.
DRIVING WITH MANUAL TRANSMISSION
(MT)
GUID-94986118-DE97-476D-8073-CD9082003FF5
WARNING:
. Do not downshift abruptly on slippery roads.
This may cause a loss of vehicle control.
. Do not over-rev the engine when shifting to
a lower gear. This may cause a loss of
vehicle control or engine damage.
CAUTION:
. Do not rest your foot on the clutch pedal
while driving. This may damage the clutch
system.
. Fully depress the clutch pedal before shift-
ing to help prevent transmission damage.
. Stop the vehicle completely before shifting
into the “R” (Reverse) position.
. When the vehicle is stopped for a period of
time, for example waiting at stoplights, shift
to the “N” (Neutral) position and release the
clutch pe dal with the foot brake pedal
depressed.
. Do not shift to the "N" (Neutral) position
while driving. Doing so may result in an
accident due to loss of engine braking.
Starting and driving 5-17
5-18 Starting and driving
Starting vehicle
GUID-6522A6DD-EA CA-4287-8F91-F52B7E8FF28C
1. After starting the engine, depress the clutch pedal
to the floor and move the shift lever to the “1” (1st)
or “R” (Reverse) position.
2. Slowly depress the accelerator pedal, releasing
the clutch pedal and parking brake at the same
time.
Shifting gear
GUID-A54E0FD6-F94B-4 469-8B26-E47E50C7AA33
SSD0084
To change gears, or when upshifting or downshifting,
fully depress the clutch pedal, shift into the appropriate
gear, then slowly and smoothly release the clutch
pedal.
To ensure smooth gear changes, fully depress the
clutch pedal before operating the shift lever. If the
clu tch pedal is not fully depr essed before the
transmission is shifted, a gear noise may be heard.
Transmission damage could occur.
Start the vehicle in the “1” (1st) position and shift to
the “2” (2nd), “3” (3rd), “4” (4th) and “5” (5th) gear in
sequence according to the vehicle speed.
You cannot shift directly from the “5” (5th) position into
the “R” (Reverse) position. First shift into the “N”
(Neutral) position, then shift into the “R” (Reverse)
position.
If it is difficult to move the shift lever into the “R”
(Reverse) or “1” (1st) position, shift to the “N” (Neutral)
position, and then release the clutch pedal once. Fully
depress the clutch pedal again and shift into “R” or “1”.
Suggested maximum speed in each gear
GUID-E0E4461B-F5D4-4 09D-BCA6-C4A5F6920A72
Downshift to a lower gear if the engine is not running
smoothly, or if you need to accelerate.
Do not exceed the maximum suggested speed (shown
below) in any gear. For level road driving, use the
highest gear suggested for that speed. Always observe
posted speed limits, and drive according to the road
conditions which will ensure safe operation. Do not
over-rev the engine when shifting to a lower gear as it
may cause engine damage or loss of vehicle control.
HR12DE engine model (for Micra Active):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
km/h (MPH)
1st 38 (24)
2nd 69 (43)
3rd 101 (63)
4th 128 (80)
5th — (—)
HR12DE engine model (for Thailand, Pakistan,
Brunei, Australia and New Zealand):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
km/h (MPH)
1st 43 (27)
2nd 79 (49)
3rd 116 (72)
4th 157 (97)
5th — (—)
HR12DE engine model (for Europe):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
km/h (MPH)
1st 51 (32)
2nd 93 (58)
3rd 137 (85)
4th 174 (108)
5th — (—)
HR12DE engine model (for Indonesia, Singa-
pore):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
km/h (MPH)
1st 39 (24)
2nd 72 (45)
3rd 105 (66)
4th 143 (89)
5th — (—)
HR12DE engine model (for Central and South
America, and Caribbean countries):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
km/h (MPH)
1st 39 (24)
2nd 71 (44)
3rd 105 (65)
4th 142 (88)
5th — (—)
HR12DE engine model (except for Thailand,
Pakistan, Australia, New Zealand, Europe, In-
donesia, Brunei, Singapore, Central and South
America, Caribbean countries and Micra Active):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
km/h (MPH)
1st 47 (29)
2nd 86 (53)
3rd 126 (78)
4th 160 (99)
5th — (—)
HR15DE engine model (for South Africa):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
km/h (MPH)
1st 44 (27)
2nd 79 (49)
3rd 117 (73)
4th 158 (98)
5th — (—)
HR15DE engine model (for the Middle East,
Lebanon and Jordan):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
km/h (MPH)
1st 43 (27)
2nd 79 (49)
3rd 116 (72)
4th 157 (97)
5th — (—)
HR12DDR engine model (for Europe):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
km/h (MPH)
1st 47 (29)
2nd 86 (53)
3rd 127 (79)
4th 171 (106)
5th — (—)
K9K engine model:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
km/h (MPH)
1st 36 (22)
2nd 65 (41)
3rd 92 (57)
4th 126 (78)
5th — (—)
GUID-F838129E-AA24-4C33-B684-4713AD9B8873
The Idling Stop System activates to prevent unneces-
sary fuel consumption, exhaust emissions and noise.
. When you stop the vehicle, the engine is turned
off automatically.
. When you start the vehicle again, the engine is
turned on automatically.
CAUTION:
When the vehicle is moved (at approximately 2
km/h or more) while the engine is stopped by
the system, such as on a downhill grade, the
engine restarts automatically. To avoid an acci-
dent, be sure to depress the brake pedal.
NOTE:
The Idling Stop System will not activate under
the following conditions:
. when the engine is kept idling without any driving
after the engine is turned on.
. when the engine coolant temperature is low.
. when the battery capacity is low.
. when the battery temperature is low or extremely
high.
. when the vehicle is moved.
. when a negative pressure booster decreases.
. when the engine hood is opened with the engine
running.
. when the engine is turned on with the engine hood
open.
. when the driver’s seat belt is not fastened.
. when the driver’s door is open.
. when the steering wheel is operated.
. when the Idling Stop System indicator blinks at a
low speed.
Starting and driving 5-19
IDLING STOP SYSTEM (for Hong
Kong)
5-20 Starting and driving
. when the accelerator pedal is depressed.
. when the shift lever is in the “R” (Reverse)
position.
. when the fan speed control dial is in any position
other than “OFF” (0) while the air flow control dial
is in the f ront defogger position (manual air
conditioner).
. when the front defogger switch is on (automatic
air conditioner).
. when the rear defogger switch is on.
. when the Idling Stop OFF switch is turned on.
. when the electric power steering warning light, the
Anti-lock Braking System (ABS) warning light, or
the Vehicle Dynamic Control (VDC) warning light
(if equipped) illuminates.
. when the brake pedal is not fully depressed.
. when stopping the vehicle on steep sloping roads.
. when the power consumption is large.
. when the vehicle is traveling at altitudes higher
than 2000 m (6562 ft).
NOTE:
It may take some time until the Idling Stop
System activates under the following conditions:
. when the battery is discharged.
. when the outside temperature is low.
. when the batte ry is replaced or the battery
terminal is disconnected for extended periods
and then reconnected.
NOTE:
The engine will not restart even if the brake
pedal is released while the Idling Stop System is
activated under the following condition:
. when the shift lever is in the “P” (Park) position.
NOTE:
The engine will restart without releasing the
brake pedal while the Idling Stop System is
activated under the following conditions:
. when the Idling Stop OFF switch is pushed.
. when the fan speed control dial is in any position
other than “OFF” (0) while the air flow control dial
is in the f ront defogger position (manual air
conditioner).
. when the front defogger switch is set to “ON”
(automatic air conditioner).
. when the rear defogger switch is set to “ON”.
. when the accelerator pedal is depressed.
. when the steering wheel is operated.
. when the battery capacity is low.
. when the power consumption is large.
. when the brake pedal is released on sloping roads
and the vehicle is moved.
. when the force to the brake pedal is reduced while
the shift lever is in the “D” (Drive) or “N” (Neutral)
position.
. when the shift lever is placed in the “L” (Low), “D”
(Drive) or “R” (Reverse) position from the “N” or
“P” position.
. when the negative pressure of the brake system is
not sufficiently applied by depressing the brake
pedal several times.
. when the driver’s seat belt is released or the
driver’s door is open.
Use this system while waiting at stoplight, etc. When
the vehicle is stopped for long periods of time, turn off
the engine.
When the engine hood is opened with the Idling Stop
System on, the engine will be in the normal stopped
state with the buzzer sounding. In this case, restart the
engine with the ignition switch.
When the engine is stopped by the Idling Stop
System, heating, cooling and dehumidifying functions
will be deactivated. To avoid the air condit io n in g
functions from being deactivated, turn off the Idling
Stop mode by pressing the Idling Stop OFF switch.
OPERATING IDLING STOP SYSTEM
GUID-68821D46-1BD2-4E1E-8925-798CDA03BCAA
NOTE:
The Idling Stop System indicator light illumi-
nates in the meter while driving if any of the
Idling Stop System conditions are met.
. When the brake pedal is depressed to stop
the vehicle with the shift lever in the “D”
(Drive) position, the engine will stop auto-
matically.
. When you release your foot from the brake
pedal, the engine will start automatically.
. The Idling Stop System indicator light and a
buzzer will inform you of the Idling Stop
System status. For more details, see “Stop/
Start System indicator light (if equipped for
Europe)/Idling Stop System indicator light
(for Hong Kong)” (P.2-18) or “Idling Stop
System reminder buzzer (for Hong Kong)”
(P.2-19).
IDLING STOP OFF SWITCH
GUID-AA97CCF7-533 1-46B5-B4CB-4843E06AB7CB
JVS0072X
The system can be temporarily deactivated by pressing
the Idling Stop OFF switch. Pressing the switch a
second time or restarting the engine by using the
ignition switch will reactivate the Idling Stop System.
. When the Idling Stop System is deactivated while
the engine is running, the engine is prevented from
automatically stopping.
. When the Idling Stop System is deactivated after
the engine has been automatically stopped by the
Idling Stop System, the engine will immediately
restart if suitable conditions are present. The
engine will then be prevented from automatically
stopping during the same journey.
. Whenever the Idling Stop System is deactivated
the indicator light on the Idling Stop OFF switch
illuminates. In this condition the Idling Stop
System cannot prevent unnecessary fuel con-
sumption, exhaust emissions, or noise during your
journey.
GUID-FA83C77F-7CB6-4222-B660-1852015F6107
The St op/Start System is designed to prevent
unnecessary fuel consumption, exhaust emissions,
and noise during a journey:
. When the vehicle comes to rest the engine is
automatically stopped.
. The engine is then automatically restarted before
you are ready to drive away.
CAUTION:
At the end of the journey the engine must be
stopped and ignition switch be turned off. Lock
the vehicle as normal. Turning the ignition OFF
will shut down all electrical systems. Failure to
do this may result in a flat battery.
NORMAL OPERATION
GUID-2F197927-FA87-4CD8-BFA3-5883AFA3970B
The Stop/Start System stops the engine and will
automatically restart the engine. The Stop/Start
indicator light is shown in the meter.
The Stop/Start System will automatically stop
the engine when all the following conditions
are valid.
GUID-BC899F05-BFD E-4C26-8AEE-DA4C489C3539
For MT model
. The shift lever is in Neutral position.
. The clutch pedal is fully released.
. The vehicle speed is below about 2 km/h (1
MPH).
. The driver’s seat belt is fastened.
. The Intelligent Key is in the vehicle.
. The driver’s door is closed.
For CVT model
. The shift lever is in the “D” (Drive) or “N” (Neutral)
position.
. The brake pedal is depressed.
. The vehicle is stopped.
. The driver’s seat belt is fastened.
. The driver’s door is closed.
NOTE:
The following conditions must also be satisfied
before the engine is automatically stopped. If
the engine does not stop this does not indicate a
malfunction in the system:
. The engine coolant temperature is at normal
operating levels.
. The vehicle has driven some distance since
engine start.
. The battery voltage and temperature are
within normal levels.
. The hood is closed.
. The steering wheel is not being turned.
. The system is not in front defogger mode.
(automatic air conditioner)
. The mode dial is not in front defogger mode.
(manual air conditioner)
. The rear window defogger is not operated.
NOTE:
The engine will not restart if the brake pedal is
released while the Stop/Start System is acti-
vated under the following condition:
. The shift lever is in the “P” (Park) position
(for CVT model).
Starting and driving 5-21
STOP/START SYSTEM (if equipped
for Europe)
5-22 Starting and driving
When the Stop/Start System indicator light is
displayed the engine starts running automa-
tically under at least one of the following
conditions.
GUID-E33B418A-AF32-4F18-B644-0C2E46C0ABB8
. The clutch pedal is depressed (for MT model).
. The brake pedal is released with the shift lever in
the "D"(Drive) or "N"(Neutral) position (for CVT
model).
. The shift lever is placed in the "L"(Low), "D"(Drive)
or "R"(Reverse) position from the "N" o r "P"
position (for CVT model).
. The driver’s seat belt is unfastened, or the driver’s
door is open (for CVT model).
. The brake pedal is repeatedly pressed (to maintain
vehicle braking performance).
. The brake pedal is strongly depressed and then
released with the shift lever in the "P" (Park)
position, resulting in decreased vacuum pressure
of the brake booster (for CVT model).
. The battery voltage becomes low (due to electrical
load from other vehicle systems like headlights,
heaters, etc., or auxiliary devices connected to the
12 volt socket inside the vehicle).
. The vehicle speed is above about 2 km/h (1
MPH).
. The system is in front defogger mode. (automatic
air conditioner)
. The mode dial is in front defogger mode. (manual
air conditioner)
. The rear window defogger is operated.
NOTE:
The following conditions will prevent the Stop/
Start System from automatically restarting the
engine. Starting the engin e by the ignition
switch is then necessary:
. The driver’s s eat belt is unfastened, or
driver’s door is open (for MT model).
. The hood is open.
The Stop/Start System is always engaged at the start
of a journey (once the engine has been started). The
engine is automatically stopped and restarted during
the journey if conditions are suitable.
STOP/START SYSTEM DISPLAY AND IN-
DICATORS
GUID-4E859066-9222-4EE3-8B37-625F6D0E240A
Engine stop
GUID-DEDDFDBC-E1A0-4A79-83BC-DD08CFBAED6B
JVS0071X
When the engine is sto pped the in formation is
displayed for a few seconds.
Vehicle information display:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
1. Engine stop guidance
Instrument panel:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
2. Stop/Start System indicator light
About the display, see “Vehicle information display”
(P.2-20).
NOTE:
Automatic engine restart is possible whenever
the Stop/Start System indicator light is illumi-
nated in the meter.
CO2 saved
GUID-7E168B68-CA45-4576-8C6F-8785E952C52A
JVS0073X
Whilst the engine remains stopped the v eh icle
information display shows the accumulated quantity
(estimate) of carbon dioxide exhaust emissions pre-
vented by the Stop/Start System.
Vehicle information display:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
1. CO2 saved information
Instrument panel:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
2. Stop/Start System indicator light
. Push and hold the
button to reset the [CO2
Saved] value.
. The display can be switched between Stop/Start
System information and drive computer informa-
tion by a short press of the
button.
System fault
GUID-5DF94D02-8E96-4667-A59C-F21B8749F543
JVS0074X
When automatic restart is not possible the information
is displayed. The engine must be started by turning or
pushing the ignition switch.
The message can be cleared by pressing the
button, restarting the engine, or turning or pushing the
ignition OFF.
Key LOCK warning
GUID-4C6CE898-770F-4674-B3F6-4FA9894132DA
JVS0081X
Type A
JVS0075X
Type B
The information is displayed and a buzzer sounded to
remind the driver to turn the ignition OFF to avoid a flat
battery
The message can only be cleared by turning or
pushing the ignition OFF (or restarting the engine).
PRECAUTIONS ON STOP/START
GUID-3C5F989E-B374-460E-8257-4159FC0AAAAB
JVS0076X
The message is displayed when there may be some-
thing wrong with the Stop/Start System. You are
advised to have the system checked by a NISSAN
dealer or qualified workshop.
Vehicle information display:
1. System fault warning
Instrument panel:
2. Stop/Start System indicator light
The message can be cleared by pressing the
button.
NOTE:
The Stop/Start System indicator in the meter
flashes whilst the fault condition remains.
STOP/START SYSTEM OFF SWITCH
GUID-F5CA1734-9CDF-43CA-AC99-B087972C6173
JVS0072X
The system can be temporarily disengaged by press-
ing the Stop/Start System OFF switch. Pressing the
button a second time will re-engage the Stop/Start
System.
. When the Stop/Start System is disengaged whilst
the engine is running, the engine is prevented from
automatically stopping.
. When the Stop/Start System is disengaged after
the engine has been automatically stopped by the
Stop/Start System, the engine will immediately
restart if suitable conditions are present as
described under NORMAL OPERATION. The
engine will then be prevented from automatically
Starting and driving 5-23
5-24 Starting and driving
stopping during the same journey.
. Whenever the Stop/Start System is disengaged
the indicator light on the Stop/Start System OFF
switch illuminates. In this condition the Stop/Start
System cannot prevent unnecessary fuel con-
sumption, exhaust emissions, or noise during your
journey.
NOTE:
The following messages may be displayed for a
few seconds in the vehicle information display
when the Stop/Start System OF F switch is
pressed.
More information about the Stop/Start System can be
checked using the [Settings] menu. (About the display,
see “Vehicle information display” (P.2-20).)
GUID-F96F2864-4FC4-4EDF-9530-9AF8A917E701
WARNING:
. The VDC system is designed to help improve
driving stability but does not prevent acci-
dents due to abrupt steering operation at
high speeds or due to careless or dangerous
driving techniques. Reduce vehicle speed
and be especially careful when driving and
cornering on slippery surfaces and always
drive carefully.
. Do not modify the vehicle’s suspension. If
suspension parts such as shock absorbers,
struts, springs, stabilizer bars, bushings and
wheels are not NISSAN-a pproved or are
extreme ly deteriorated, the VDC system
may not operate properly. This could ad-
versely affect vehicle handling performance,
and the “VDC OFF” ind icator or “SLIP”
indicator or both indicator lights may illumi-
nate.
. If brake related parts such as brake pads,
rotors and calipers are not standard equip-
ment o r are e xtremely de teriorated, the
“VDC OFF” indicator or “SLIP” indicator or
both indicator lights may illuminate.
. If engine related parts such as a muffler are
not standard equipment or are extremely
deteriorated, the “VDC OFF” indicator or
“SLIP” indicator or both indicator lights
may illuminate.
. When driving on extremely inclined surfaces
such as higher banked corners, the VDC
system may not operate properly and the
“VDC OFF” indicator or “SLIP” indicator or
both indicator lights may illuminate. Do not
drive on these types of roads.
. When driving on unstable surfaces such as a
turntable, ferry, elevator or ramp, the “VDC
OFF” indicator or “SLIP” indicator or both
indicator lights may illuminate. This is not a
malfunction. Restart the engine after driving
onto a stable surface.
. If wheels or tires other than those recom-
mended are used, the VDC system may not
operate properly and “VDC OFF” indicator or
“SLIP” indicator or both indicator lights may
illuminate.
. The VDC system is not a substitute for winter
tires or tire chains on a snowcovered road.
When accelerating or driving on slippery surfaces, the
tires may spin or slide. With the Vehicle Dynamic
Control (VDC) system, sensors detect these move-
ments and control the braking and engine output to
help improve vehicle stability.
. When the VDC system is operating, the “SLIP”
indicator in the instrument panel blinks.
. If the “SLIP” indicator blinks, the road conditions
are slippery. Be sure to adjust your speed and
driving to these conditions . Be sure to drive
carefully. (See “Slip indicator light (if equipped
except for Australia and New Zealand)” (P.2-17)
and “Vehicle Dynamic Control (VDC) off indicator
light” (P.2-18).)
. Indicator light
If a malfunction occurs in the system, the “SLIP”
and “VDC OFF” indicator lights illuminate in the
instrument panel. As long as these indicators are
illuminated, the VDC system function is canceled.
The VDC system uses a Brake Limited Slip Differential
(BLSD) function to improve vehicle traction. The BLSD
system works when one of the driving wheels is
spinning on a slippery surface. The BLSD system
VEHICLE DYNAMIC CONTROL (VDC)
SYSTEM (if equipped except for
Europe, Australia and New Zealand)
brakes the spinning wheel, which distributes the
driving power to the other drive wheel. If the vehicle
is operated with the VDC OFF switch pushed and the
VDC system turned off, all VDC systems will be turned
off. The BLSD system will still operate with the VDC
system off. If the BLSD system is activated, the “SLIP”
indicator light will blink and you may hear a clunk noise
and/or feel a pulsation in the foot brake pedal. This is
normal and is not an indication of a malfunction. While
the VDC system is operating, you may feel a pulsation
in the foot brake pedal and hear a noise or feel a
vibration from under the hood. This is normal and
indicates that the VDC system is working properly.
The VDC system computer has a built-in diagnostic
feature that tests the system each time you start the
engine and move the vehicle at a low speed forward or
backward. When the self-test occurs, you may hear a
“clunk” noise and/or feel a pulsation in the foot brake
pedal. This is normal and is not an indication of a
malfunction.
VEHICLE DYNAMIC CONTROL (VDC) OFF
SWITCH
GUID-A27A29D3-3727-4957-BCED-5BF88952872D
SIC1881
The vehicle should be driven with the Vehicle Dynamic
Control (VDC) system ON for most driving conditions.
When the vehicle is stuck in mud or snow, the VDC
system reduces the engine output to reduce wheel
spin. The engine speed will be reduced even if the
accelerator is depressed to the floor. If maximum
engine power is needed to free a stuck vehicle, turn
the VDC system off.
To turn off the Vehicle Dynamic Control (VDC) system,
push the VDC OFF switch. The
indicator light will
illuminate.
Push the VDC OFF switch again or restart the engine
to turn ON the system.
GUID-1CE921CF-0C35-4 69C-98F6-025CE0172659
WARNING:
. The VDC system is designed to help the
driver maintain stability but does not pre-
vent accidents due to abrupt steering opera-
tion at h igh speeds or by careless or
dangerous driving techniques. Reduce vehi-
cle speed and be especially careful when
driving and cornering on slippery surfaces
and always drive carefully.
. Do not modify the vehicle’s suspension. If
suspension parts such as shock absorbers,
struts, springs, stabilizer bars, bushings and
wheels are not NISSAN recommended for
your vehicle or are extremely deteriorated,
the VDC system may not operate properly.
This could adversely affect vehicle handling
performance, and the VDC warning light
may illuminate.
. If brake related parts such as brake pads,
rotors and calipers are not NISSAN recom-
mended or are extremely deteriorated, the
VDC system may not operate properly and
the VDC warning light
may illuminate.
. If engine c ontrol related parts are not
NISSAN recommended or are extremely
deteriorated, the VDC w arning light
may illuminate.
. When driving on extremely inclined surfaces
such as higher banked corners, the VDC
system may not operate properly and the
VDC warning light
may illuminate. Do
not drive on these types of roads.
. When driving on an unstable surface such as
a turntable, ferry, elevator or ramp, the VDC
warning light
may illuminate. This is not
Starting and driving 5-25
VEHICLE DYNAMIC CONTROL (VDC)
SYSTEM (for Australia and New
Zealand)
5-26 Starting and driving
a malfunction. Resta rt the engine after
driving onto a stable surface.
. If wheels or tires other than the NISSAN
recommended ones are used, the VDC
system may not operate properly and the
VDC warning light
may illuminate.
. The VDC system is not a substitute for winter
tires or tire chains on a snow covered road.
The Vehicle Dynamic Control (VDC) system uses
various sensors to monitor driver inputs and vehicle
motion. Under certain driving conditions, the VDC
system helps to perform the following functions.
. Controls brake pressure to reduce wheel slip on
one slipping drive wheel so power is transferred to
a non slipping drive wheel on the same axle.
. Controls brake pressure and engine output to
reduce drive wheel slip based on vehicle speed
(traction control function).
. Controls brake pressure at individual wheels and
engine output to help the driver maintain control of
the vehicle in the following conditions:
— understeer (vehicle tends to not follow the
steered path despite increased steering input)
— oversteer (vehicle tends to spin due to certain
road or driving conditions).
The VDC system can help the driver to maintain control
of the vehicle, but it cannot prevent loss of vehicle
control in all driving situations.
When the VDC system operates, the VDC warning
light
in the instrument panel flashes so note the
following:
. The road may be slippery or the system may
determine some action is required to help the
vehicle on the steered path.
. You may feel a pulsation in the brake pedal and
hear a noise or vibration from under the hood. This
is normal and indicates that the VDC system is
working properly.
. Adjust your speed and driving to the road
conditions.
If a malfunction occurs in the system, the VDC warning
light
illuminates in the instrument panel. The VDC
system automatically turns off.
The VDC OFF switch is used to turn off the VDC
system. The VDC off indicator light
illuminates to
indicate the VDC system is off. When the VDC OFF
switch is used to turn off the system, the VDC system
still operates to prevent one drive wheel from slipping
by transferring power to a non slipping drive wheel.
The VDC warning light
flashes if this occurs. All
other VDC functions are off and the VDC warning light
will not flash. The VDC system is automatically
reset to on when the ignition switch is placed in the
“OFF” position then back to the “ON” position.
See “Vehicle Dynamic Control (VDC) warning light (for
Australia and New Zealand)” (P.2-16) and “Vehicle
Dynamic Control (VDC) off indicator light” (P.2-18).
The computer has a built-in diagnostic feature that
tests the system each time you start the engine and
move the vehicle forward or in reverse at a slow speed.
When the self-test occurs, you may hear a “clunk”
noise and/or feel a pulsation in the brake pedal. This is
normal and is not an indication of a malfunction.
VEHICLE DYNAMIC CONTROL (VDC) OFF
SWITCH
GUID-941C52A4-286C-4DB0-AFFC-1563619EE044
SSD1153
The vehicle should be driven with the Vehicle Dynamic
Control (VDC) system ON for most driving conditions.
When the vehicle is stuck in mud or snow, the VDC
system reduces the engine output to reduce wheel
spin. The engine speed will be reduced even if the
accelerator is depressed to the floor. If maximum
engine power is needed to free a stuck vehicle, turn
the VDC system off.
To turn off the Vehicle Dynamic Control (VDC) system,
push the VDC OFF switch. The
indicator light will
illuminate.
Push the VDC OFF switch again or restart the engine
to turn ON the system.
GUID-0FAE2978-396B-4B69-ADBC-305CF72F2243
WARNING:
. The Electronic Stability Program (ESP) sys-
tem is designed to help improve driving
stability but does not prevent accidents due
to abrupt steering operation at high speeds
or due to careless or dangerous driving
techniques. Reduce vehicle speed and be
especially careful when driving and corner-
ing on slippery surfaces and always drive
carefully.
. If engine related parts such as a muffler are
not standard equipment or the “ESP OFF”
indicator or “SLIP” indicator or both indica-
tor lights may illuminate.
. Do not modify the vehicle’s suspension. If
suspension parts such as shock absorbers,
struts, springs, stabilizer bars and bushings
are not NISSAN approved or are extremely
deteriorated the ESP system may not oper-
ate properly. Thi s could adversely af fect
vehicle handling performance, and the
“ESP OFF” indicator or “SLIP” indicator or
both indicator lights may illuminate.
. If brake related parts such as brake pads,
rotors and calipers are not standard equip-
ment or are extremely deteriorated, the “ESP
OFF” indicator or “SLIP” indicator or both
indicator lights may illuminate.
. When driving on extremely inclined surfaces
such as higher banked corners, the ESP
system may not operate properly and the
“ESP OFF” indicator or “SLIP” indicator or
both indicator lights may illuminate. Do not
drive on these types of roads.
. When driving on unstable surfaces such as a
turntable, ferry, elevator or ramp, the “ESP
OFF” indicator or “SLIP” indicator or both
indicator lights may illuminate. This is not a
malfunction. Restart the engine after driving
onto a stable surface.
. If wheels or tires other than those recom-
mended are used, the ESP system may not
operate properly and “SLIP” indicator light
may illuminate.
. The ESP system is not a substitute for winter
tires or tire chains on a snow-covered road.
. When the ESP system is operating, the “SLIP”
indicator
in the instrument panel blinks.
. If the “SLIP” indicator blinks, the road conditions
are slippery. Be sure to adjust your speed and
driving to these conditions . Be sure to drive
carefully. (See “Slip indicator light (if equipped
except for Australia and New Zealand)” (P.2-17)
and “Electronic Stability Program (ESP) off
indicator light” (P.2-16).)
. Indicator light
If a malfunction occurs in the system, the “SLIP”
and “ESP OFF” indicator lights illuminate in the
instrument panel. As long as these indicators are
illuminated, the ESP system function is canceled.
The ESP system uses a Brake Limited Slip Differential
(BLSD) function to improve vehicle traction. The BLSD
system works when one of the driving wheels is
spinning on a slippery surface. The BLSD system
brakes the spinning wheel, which distributes the
driving power to the other drive wheel. If the vehicle
is operated with the ESP system turned off, all ESP
system functions will be turned off.
The BLSD system and ABS will still operate with the
ESP system off. If the BLSD system is activated, the
“SLIP” indicator light will blink and you may hear a
clunk noise and/or feel a pulsation in the brake pedal.
This is normal and is not an indication of a malfunction.
While the ESP system is operating, you may feel a
pulsation in the brake pedal and hear a noise or feel a
vibration from under the hood. This is normal and
indicates that the ESP system is working properly.
The ESP system computer has a built-in diagnostic
feature that tests the system each time you start the
engine and move the vehicle at a low speed forward or
backward. When the self-test occurs, you may hear a
“clunk” noise and/or feel a pulsation in the foot brake
pedal. This is normal and is not an indication of a
malfunction.
ELECTRONIC STABILITY PROGRAM (ESP)
OFF SWITCH
GUID-FA65705E-C519-449E-8010-901C83F34F58
JVS0022X
The vehicle should be driven with the Electronic
Stability Program (ESP) system on for most driving
conditions.
When the vehicle is stuck in mud or snow, the ESP
system reduces the engine output to reduce wheel
spin. The engine speed will be reduced even if the
accelerator is depressed to the floor. If maximum
engine power is needed to free a stuck vehicle, turn
Starting and driving 5-27
ELECTRONIC STABILITY PROGRAM
(ESP) SYSTEM (if equipped for
Europe)
5-28 Starting and driving
the ESP system off.
To turn off the ESP system, push the ESP OFF switch
located on the lower side of the instrument panel.
The
indicator light will illuminate.
Push the ESP OFF switch again or restart the engine
to turn on the system.
GUID-E4B23E71-BE78-446C-B2E6-E1777649C0A7
The speed limiter allows you to set the desired vehicle
speed limit. While the speed limiter is activated, the
driver can perform normal braking and acceleration,
but the vehicle will not exceed the set speed.
WARNING:
. Always observe posted speed limits. Do not
set the speed over them.
. Always confirm the setting status of the
speed limiter on the vehicle information
display and instrument panel.
When the speed limiter is on, the cruise control cannot
be operated.
SPEED LIMITER OPERATIONS
GUID-3846061C-6CD2-491B-A17E-85B78B8637C0
Except for HR12DDR engine model: The speed limiter
can be set between 30 km/h and 170 km/h or 20 MPH
and 105 MPH.
For HR12DDR engine model (for MT model): The
speed limiter can be set between 30 km/h and 180
km/h or 20 MPH and 112 MPH.
For HR12DDR engine model (for CVT model): The
speed limiter can be set between 30 km/h and 170
km/h or 20 MPH and 105 MPH.
The speed limiter set switches are located on the
steering wheel.
SSD0891
1. RES/+ switch
2. SET/− switch
3. CANCEL switch
4. Cruise control MAIN swit ch (For details, see
“Cruise control” (P.5-30).)
5. Speed limiter MAIN switch
(When this switch is pushed, the speed limiter
enters the standby mode. If the cruise control
system is on, the system will turn off and the
speed limiter enters the standby mode.)
Speed limiter display and indicators (Type B
model)
GUID-7FFB2EFF-CC3 9-4983-A020-783FC9244E73
JVS0019X
SPEED LIMITER (if equipped for
Europe)
The speed limiter operating condition is shown on the
vehicle information display and instrument panel.
Vehicle information display:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
1. LIMIT indicator
2. Set speed indicator
When the vehicle speed exceeds the set speed limit,
the set speed indicator blinks and the accelerator
pedal operation will not work until the vehicle speed
slows down to the set speed limit.
Instrument panel:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
3. Speed limiter indicator light
4. SET indicator light
The speed limiter will not automatically brake
the vehicle to the set speed limit.
Speed limiter display and indicators (Type C
model)
GUID-46A78D73-3FA6-46E5-BEBC-10AFFFBE6F3A
JVS0025X
The speed limiter operating condition is shown on the
vehicle information display and instrument panel.
Vehicle information display:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
1. LIMIT indicator
2. SET indicator light
3. Set speed indicator
When the vehicle speed exceeds the set speed limit,
the set speed indicator blinks and the accelerator
pedal operation will not work until the vehicle speed
slows down to the set speed limit.
Instrument panel:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
4. Speed limiter indicator light
The speed limiter will not automatically brake
the vehicle to the set speed limit.
Turning on speed limiter
GUID-407B9770-D025-46F8-A1E6-B9F40D9E1DE2
Push the speed limiter MAIN switch. The speed limiter
indicator (light) and the LIMIT indicators illuminate. The
set speed indicator shows “- - -”.
Setting speed limit
GUID-C925D9B5-EDE5-41B2-83B9-C278ED3FDECF
1. Push the SET/− switch.
.
When the vehicle is stopped, the speed will be
set at 30 km/h or 20 MPH.
.
While driving, the speed limit will be set at the
current speed.
2. When the speed limit is set, the SET (indicator
light) and the set speed indicators illuminate on
the vehicle information display and instrument
panel (for Type B model).
Changing set speed limit:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Use either of the following operations to change the
speed limit.
. Push and hold the RES/+ or SET/− switch. The
set speed will increase or decrease by approxi-
mately 10 km/h or 10 MPH.
. Push, then quickly release the RES/+ or SET/−
switch. Each time you do this, the set speed will
increase or decrease by approximately 1 km/h or 1
MPH.
Resuming preset speed limit:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push the RES/+ switch. The SET indicator (light)
illuminates, and the speed limiter will resume the last
set speed limit. If the vehicle is driven at a speed over
the last set speed limit, the set speed indicator will
blink.
Canceling speed limit
GUID-F503ED75-E45E-411A-BCD7-E621DB8FF464
To cancel the speed limiter, push the CANCEL switch.
The SET indicator (light) will turn off. (The set speed
indicator will remain on the display.)
If the accelerator pedal is fully depressed (beyond the
resistance point), the speed limi ter is temporarily
suspended and the vehicle speed may be controlled
above the set speed. (For Continuously Varia ble
Transmission model: The transmission may downshift
into a lower gear). The SET indicator (light) will remain
on the instrument panel (for Type B model) or vehicle
information display (for Type C model).
If the accelerator pedal returns to the resistance point
and the vehicle speed returns to the set speed, the
speed limiter will activate and limit vehicle speed.
When one of the following operations is performed, the
speed limiter will be canceled. The speed limiter
indicator light, and the SET indicator (light) and the
LIMIT indicator will turn off. These canceling methods
will erase the set speed limit memory.
. Push the speed limiter MAIN switch.
. Push the cruise control MAIN switch.
Starting and driving 5-29
5-30 Starting and driving
Speed limiter malfunction
GUID-C39E8711-EE6C-4221-850A-2231CDF4D761
Type B model:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
If the speed limiter malfunctions, the SET indicator light
on the instrument panel will blink. Turn the speed
limiter MAIN switch off and have the system checked
by a NISSAN dealer.
Type C model:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
If the speed limiter malfunctions, the SET indicator on
the vehicle information display will blink. Turn the
speed limiter MAIN switch off and have the system
checked by a NISSAN dealer.
GUID-CA276E64-38DA-4CCF-ADC4-3D4617C3E588
WARNING:
. Always observe the posted speed limits and
do not set the speed over them.
. Do not use the cruise control when driving
under the following conditions. Doing so
could cause a loss of vehicle control and
result in an accident.
— When it is not possible to keep the
vehicle at a constant speed
— When driving in heavy traffic
— When driving in traffic that varies speed
— When driving in windy areas
— When driving on winding or hilly roads
— When driving on slippery (rain, snow, ice,
etc .) roads
CAUTION:
On manual Transmission (MT) model, do not
shift to the “N” (N eu tr al ) positi on without
depressing the clutch pedal when the cruise
control is operated. Should this occur, depress
the clutch pedal and turn the cruise control MAIN
switch off immediately. Failure to do so may
cause engine damage.
PRECAUTIONS ON CRUISE CONTROL
GUID-B1AE8EEF-7078-40AB-82DC-358EDB12995F
. If the cruise control system malfunctions, it
cancels automatically. The SET indicator and the
cruise control indicator light will blink to warn the
driver.
. If the engine coolant temperature becomes
excessively high, the cruise control system will
be canceled automatically.
. If the SET indicator and cruise control indicator
light blink, turn off the cruise control MAIN switch
and have the system checked by a NISSAN
dealer.
. The SET indicator and cruise control indicator
light may blink when the cruise control MAIN
switch is turned on while pushing the RES+, SET
−, CANCEL switch. To properly set the cruise
control system, use the following procedures.
CRUISE CONTROL OPERATIONS
GUID-DF60F09D-4F46-4C86-9D91-055490ADB31D
The cruise control allows driving at speeds above 40
km/h (25 MPH) without keeping your foot on the
accelerator pedal.
The cruise control will automatically be canceled if the
vehicle slows down more than approximately 13 km/h
(8 MPH) below the set speed.
Moving the shift lever to the “N” (Neutral) position
(Continuously Variable Transmission model) or depres-
sing the clutch pedal (Manual Transmission model) will
cancel the cruise control and the SET indicator will
turn off.
The cruise control switches are located on the steering
wheel.
CRUISE CONTROL (if equipped)
SSD0891
1. RES/+ switch
2. SET/− switch
3. CANCEL switch
4. Cruise control MAIN switch
5. Speed limiter MAIN switch (For details, see
“Speed limiter (if equipped for Europe)” (P.5-28).)
Cruise control display and indicators (Type B
model)
GUID-2F9A21B0-2F26-44A2-A8D6-16BFD1BEC5DF
JVS0027X
The cruise control operating condition is shown on the
vehicle information display and instrument panel.
Vehicle information display:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
1. CRUISE indicator
2. Set speed indicator
Instrument panel:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
3. Cruise control indicator light
4. SET indicator light
Cruise control display and indicators (Type C
model)
GUID-41DAD620-68D8-4B71-9E44-9DD56766EAD1
JVS0028X
Vehicle information display:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
1. CRUISE indicator
2. SET indicator light
3. Set speed indicator light
Instrument panel:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
4. Cruise control indicator light
Turning on cruise control
GUID-6BA37096-769E-40E3-8899-77AF6559A97F
Push the cruise control MAIN switch. The cruise
control indi cator light illuminates. The set speed
indicator shows “- - -”.
Setting cruising speed
GUID-2F50812A-448F-4C9F-8BF3-E4122114865C
1. Accelerate to the desired speed.
2. Push the SET− switch and release it.
3. The SET indicator light and set speed indicator
illuminate on the meter panel and the vehicle
information display.
4. Take your foot off the accelerator pedal.
The vehicle will maintain the set speed.
Passing another vehicle:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Depress the accelerator pedal to accelerate. After
releasing the accelerator pedal, the vehicle will return
to the previously set speed.
The vehicle may not maintain the set speed when
going up or down steep hills. In such cases, drive
without the cruise control.
Resetting to slower speed:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Use any one of the following methods to reset to a
slower speed.
. Lightly tap the foot brake pedal. When the vehicle
reaches the desired speed, push and release the
SET− switch.
. Push and hold the SET− switch. When the vehicle
reaches the desired speed, release the SET−
switch.
. Quickly push and release the SET− switch. This
will reduce the vehicle speed by about 1 km/h or 1
MPH.
Resetting to faster speed:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Use any one of the following methods to reset to a
faster speed.
. Depress the accelerator pedal. When the vehicle
reaches the desired speed, push and release the
SET− switch.
Starting and driving 5-31
5-32 Starting and driving
. Push and hold t he RES+ switch. When the
vehicle reaches the desired speed, release the
RES+ switch.
. Quickly push and release the RES+ switch. This
will increase the vehicle speed by about 1 km/h or
1 MPH.
Resuming at preset speed:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Push and release the RES+ switch.
The vehicle will resume the last set cruising speed
when the vehicle speed is over 40 km/h (25 MPH).
Canceling cruising speed
GUID-BD4D37C9-5C2C-4220-B1EB-BBC1BCD039CB
Use any one of the following methods to cancel the set
speed.
. Push the CANCEL switch. The SET indicator light
will turn off.
. Tap the foot brake pedal. The SET indicator light
will turn off.
. Push the cruise control MAIN switch. Both the
SET and cruise indicator lights turn off.
GUID-B793299F-95F1-4615-A185-C5009A36E567
WARNING:
. Do not stop or park the vehicle over
flammable mat erials such as dry grass,
waste paper or rags. They may ignite and
cause a fire.
. Safe parking procedures require that both
the parking brake be applied and the shift
lever placed in the “P” (Park) position
(Automatic Transmission model/Continu-
ously Variable Transmission model) or the
shift lever placed in an appropriate gear
(Manual Transmission model). Failure to do
so could cause the vehicle to move unex-
pectedly or roll away and result in an
accident.
. When parking the vehicle, make sure the
shif t lever is mo ved to the “P” (Park)
position. The shift lever cannot be moved
o ut of the “P” (Park) p osition without
depressing the foot brake pedal (Automatic
Transmission model/Continuously Variable
Transmission model).
. Never leave the engine running while the
vehicle is unattended.
. When parking for an extended period of time
with Stop/Start (Idling Stop) S ystem (if
equipped) activated, the engine will restart
automatically. Never leave the vehicle with
the ignition switch in the “ON” position.
. Never leave children or adults who would
normally require the support of others alone
in the vehicle. Pets should not be left alone
either. They could unknowingly activate
switches or controls and inadvertently be-
come involved in a serious accident and
injure themselv es . On hot, sunny days,
temperatures in a closed veh icle could
quickly become high enough to cause se-
vere or possibly fatal illness to people and
animals.
PARKING
SSD0488
Left-Hand Drive (LHD) model
SSD0489
Right-Hand Drive (RHD) model
1. Firmly apply the parking brake.
2. Automatic Transmission (AT)/Continuously Vari-
able Transmission (CVT) model: Move the shift
lever to the “P” (Park) position.
Manual Transmission (MT) model: Move the shift
lever to the “R” (Reverse) position. When parking
on an uphill grade, move the shift lever to the “1”
(1st) position.
3. To help prevent the vehicle from moving into traffic
when parked on an incline, it is a good practice to
turn the wheels as illustrated.
HEADED DOWNHILL WITH CURB
*
1
Turn the wheels into the curb and move the vehicle
forward until the curb side wheel gently touches
the curb. Then apply the parking brake.
HEADED UPHILL WITH CURB
*
2
Turn the wheels away from the curb and allow the
vehicle to move back until the curb side wheel
gently touches the curb. Then apply the parking
brake.
HEADED UPHILL OR DOWNHILL, WITHOUT
CURB
*
3
Turn the wheels toward the side of the road so the
vehicle will move away from the center of the road
if the vehicle moves. Then apply the parking brake.
4. Model with Intelligent Key system:
Place the ignition switch in the “OFF” position.
Model without Intelligent Key system:
Place the ignition switch in the “LOCK” position
and remove the key.
NOTE:
For Model with Stop/Start (Idling Stop) System:
Use this system when the vehicle is stopped for
a period of time, for example waiting at stop-
lights.
Stop the engine with the ignition switch when
parking, etc. for an extended period of time.
Starting and driving 5-33
5-34 Starting and driving
GUID-0B8C906D-4D83-49A6-9547-446E8A1795EC
SSD0723
WARNING:
. The son ar (parking sensor) system is a
convenience but it is not a substitute for
proper p arking. Always look around and
check that it is safe to do so before parking.
Always move slowly.
. Read and understand the limitations of the
sonar (parking sensor) system as contained
in this section. Inclement weather may affect
the function of the sonar (parking sensor)
system; this may include reduced perfor-
mance or a false activation.
. This system is not designed to prevent
contact with small or moving objects.
. The system is designed as an aid to the
driver in detecting large stationary objects to
help avoid damaging the vehicle. The system
will not detect small objects below the
bumper, and may not detect objects close
to the bumper or on the ground.
. If your vehicle sustains damage to the
bumper fascia, leaving it misaligned or bent,
the sensing zone may be altered causing
inaccurate measurement of obstacles or
false alarms.
CAUTION:
Keep the interior of the vehicle as quiet as
possible to hear the tone clearly.
When the ignition switch is in the “ON” position, the
sonar (parking sensor) system is operational.
The sonar (parking sensor) system sounds a tone to
warn the driver of obstacles near the bumper. The
parking sensor indicator will also appear in the vehicle
information display. (See “Parking Sensor Indicator”
(P.5-34)). The system detects rear obstacles when the
shift lever is in the “R” (Reverse) position. The system
may not detect objects at speeds above 10 km/h (6
MPH) and may not detect certain angular or moving
objects.
The sonar (parking sensor) system detects obstacles
up to 1 m (3.3 ft) from the bumper with a decreased
coverage area at the outer corners of the bumper,
(refer to the illustration for approximate zone coverage
areas). As you move closer to the obstacle, the rate of
the tone increases. When the obstacle is less than 30
cm (11.8 in) away, the tone will sound continuously.
Keep the sonar sensors (located on the bumper fascia)
free from snow, ice and large accumulations of dirt (do
not clean the sensors with sharp objects). If the
sensors are covered, it will affect the accuracy of the
sonar (parking sensor) system.
If the sonar (parking sensor) system malfunc-
tions, the beep sounds for 3 seconds when the
shift lever is moved to the “R” (Reverse) position.
Have the system checked by a NISSAN dealer.
PARKING SENSOR INDICATOR
GUID-91B967FD-83D8-4004-AB4B-C03CAF59B214
JVS0026X
*
1
Parking sensor display
*
A
Corner sensor indicator
*
B
Center sensor indicator
With the sonar (parking sensor) system ON in the “R”
(Reverse) position, when the corner/center sensors
(sonar) detect obstacles near the bumper, a tone will
sound and the parking sensor indicator will appear in
the vehicle information display
*
1
.
The parking sensor indicators
*
A
and
*
B
indicate
the position of the object and the distance to the
object with the rate of blinking.
When an object is detected, the indicator appears and
SONAR (parking sensor) SYSTEM (if
equipped)
blinks (the tone sounds intermittently). When the
vehicle moves closer to the object, the number of bars
decreases and the rate of blinking increases (the rate
of the tone increases). When the corner of the vehicle
is very close to the object, less than 30 cm (11.8 in)
away, the number of bars decreases and the indicator
stops blinking (the tone sounds continuously).
PARKING SPACE MEASUREMENT OP-
ERATION (if equipped)
GUID-D0D65601-6F70 -41C5-BC03-748FD29E7F8C
System operation
GUID-88315A6B-EBB2-49A8-98C0-E2E4B80BB77A
JVS0020X
Parking space measurement switch
*
1
Parking space measurement switch
*
2
ON indicator light
The system is intended to help the driver parallel park
easily. When the system is activated by pressing the
switch, i t informs the driver of parallel parking
availability.
Press the switch
*
1
to turn on the parking space
measurement system.
JVS0030X
1. Select left or right to parallel park by operating the
turn signal switch.
2. Drive the vehicle alongside the cars you will
parallel park between at approximately 15 km/h (9
MPH). Maintain approximately a one meter dis-
tance between your vehicle and the one next to
your vehicle as illustrated
*
A
.
3. When the parking space is measured, a beep
sounds.
Starting and driving 5-35
5-36 Starting and driving
JVS0031X
Measurement result:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
The display indicating the measurement result
*
B
(“OK”, “DIFFICULT” or “NOT ADVISED” ) will appear in
the meter as illustrated.
CAUTION:
. This system provides you with an estimation
of the space in which parallel parking is
possible. Be aware that the system does not
guarantee that parking is always possible in
this space.
. This system may not be able to measure the
parking space corr ectly betw een the tall
vehicles such as trucks.
. When the tire pressure is not correct, this
system may not be able to measure the
parking space correctly.
. When replacing a tire with one other than a
genuine NISSAN tire (the same size as the
original tire), have your vehicle adjusted by
NISSAN dealer. If genuine NISSAN tires are
not used, the sys tem cannot guarant ee
accurate measurement of the parking space.
. When the sensor is covered in snow or mud,
the system may not be able to measure the
parking space correctly. Always keep your
sensor clean.
JVS0029X
*
1
Parking space measurement switch
*
2
ON indicator light
Setting the level mode:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Depending on your driving level, the modes can be
selected from the following.
. Amateur
. Normal
. Expert
To set the mode, perform the following procedure:
1. Push and hold the parking space measurement
switch
*
1
for at least 5 seconds. The buzzer then
sounds for 5 seconds.
2. Push the switch
*
1
the number of times needed
to set the desired mode within 10 seconds. After
10 seconds, the buzzer sounds the number of
times previously pushed.
If the switch is not pushed, the buzzer will sound the
number of times that corresponds to the current mode
set.
The mode can be selected to "Amateur", "Normal" and
"Expert" by pushing the switch once to three times
while the buzzer sounds as follows:
. Push the switch once to select Amateur mode.
. Push the switch two times to select Normal mode.
. Push the switch three times to select Expert mode.
Each mode indicates the size of space in which
parking is possible as follows:
. The Amateur mode indicates the largest parking
space.
. The Normal mode indicates the medium parking
space.
. The Expert mode indicates the smallest parking
space.
System malfunction
GUID-392B155A-D8B0-4AA5-9F24-BE54C27DC64A
JVS0032X
If the “SYSTEM ERROR” display appears and/or the
ON indicator light on the parking space measurement
switch blinks, have the system checked by a NISSAN
dealer.
GUID-7573BD22-B96C-4CEE-B1D0-6B84012F9147
Your vehicle was designed to be used t o carry
passengers and luggage. NISSAN does not recom-
mend trailer towing, because it places additional loads
on your vehicle’s engine, drivetrain, steering, braking,
and other systems.
CAUTION:
Vehicle damage resulting from towing a trailer is
not covered by the warranty.
GUID-C0D56209-F4FF-42D8-B9FB-514E99ED3789
WARNING:
. If the engine is not running or is turned off
while driving, the power assist for the
steering will not work. The steering will be
harder to operate.
. When the electric power steering warning
light illuminates with the engine running, the
power assist for the steering will cease
operation. You will still have control of the
vehicle but the steering will be harder to
operate.
The electric power steering system is designed to
provide power assist while driving to operate the
steering wheel with light force.
When the steering wheel is operated repeatedly or
continuously while parking or driving at a very low
speed, the power assist for the steering wheel will be
reduced. This is to prevent overheating of the electric
power steering system and protect it from getting
damaged. While the power assist is reduced, steering
wheel operation will become heavy. When the
temperature of the electric power steering system
goes down, the power assist level will return to normal.
Avoid repeating such steering wheel operations that
could cause the electric power steering system to
overheat.
You may hear a fricative sound when the steering
wheel is operated quickly. However, this is not a
malfunction.
If the electric power steering warning light
illuminates while the engine is running, it may indicate
the electric power steering system is not functioning
properly and may need servicing. Have the electric
power steering system checked by a NISSAN dealer.
(See “Electric power steering warning light” (P.2-14).)
Starting and driving 5-37
TRAILER TOWING
ELECTRIC POWER STEERING
SYSTEM
5-38 Starting and driving
When the electric power steering warning light
illuminates with the engine running, the power assist
for the steering will cease operation. You will still have
control of the vehicle. However, greater steering effort
is needed, especially in sharp turns and at low speeds.
GUID-C25737EF-56EA-4 67D-853B-730CA88564CA
The brake system has two separate hydraulic circuits. If
one circuit malfunctions, you will still have braking
ability at two wheels.
BRAKE PRECAUTIONS
GUID-5ED7A9E3-DD89-4696-93AF-56B5DB3C0003
Vacuum assisted brakes
GUID-245EE7F6-3D50-464D-A039-2DD804274920
The b rake booster aids braking by using engine
vacuum. If the engine stops, you can stop the vehicle
by depressing the foot brake pedal. However, greater
foot pressure on the foot brake pedal will be required
to stop the vehicle. The stopping distance will be
longer.
If the engine is not running or is turned off while driving,
the power assisted brakes will not function. Braking
will be harder.
WARNING:
Do not coast with the engine stopped.
When the brake pedal is depressed slowly and firmly,
you may hear a clicking noise and feel a slight
pulsation. This is normal and indicates that the Brake
Assist System is operating.
Using brakes
GUID-6C148A06-8EF3 -4376-A202-3C898260E0FA
Avoid resting your foot on the foot brake pedal while
driving. This will overheat the brakes, wear out the
brake linings/pads faster, and increase fuel consump-
tion.
To help reduce brake wear and to prevent the brakes
from overheating, reduce speed and downshift to a
lower gear before going down a slope or long grade.
Overheated brakes may reduce braking performance
and could result in loss of vehicle control.
While driving on a slippery surface, be careful when
braking, accelerating or downshifting. Abrupt braking
or acceleration could cause the wheels to skid and
result in an accident.
Wet brakes
GUID-F8A6E2E5-8884-4944-AC78-1DDCCC3675A6
When the vehicle is washed or driven through water,
the brakes may get wet. As a result, your braking
distance will be longer and the vehicle may pull to one
side during braking.
To dry the brakes, drive the vehicle at a safe speed
while lightly depressing the foot brake pedal to heat up
the brakes. Do this until the brakes return to normal.
Avoid driving the vehicle at high speeds until the
brakes function correctly.
Driving uphill
GUID-B5D60729-0 9B7-4553-95E5-09E85613FEDC
When starting on a steep grade, it is sometimes
difficult to operate both the brake and clutch (for
Manual Transmission model). Apply the parking brake
to hold the vehicle. Do not slip the clutch. When ready
to start, slo wly release the parking brake while
depressing the accelerator pedal and releasing the
clutch pedal.
Driving downhill
GUID-4D5CC9CA-C086-4BF6-87EA-A672BD9EDBCE
The engine braking action is effective for controlling
the vehicle while descending hills. For Manual Trans-
mission (MT) model, the shift lever should be placed in
the lower speed position prior to descending. For
Automatic Transmission (AT) model, the “1” or “2”
position should be selected. For Continuously Variable
Transmission (CVT) model, the “L” position should be
selected.
BRAKE SYSTEM
BRAKE ASSIST (if equipped)
GUID-C3D601A6-A2D C-4991-8022-BE0965B17AF6
When the force applied to the brake pedal exceeds a
certain level, the Brake Assist is activated, generating
gr eater braking force than a conventional brake
booster even with light pedal force.
WARNING:
The Brake Assist is only an aid to assist braking
operation and is not a collision warning or
avoidance device. It is the driver’s responsibility
to stay alert, drive safely and be in control of the
vehicle at all times.
GUID-BE009EC4-2731-4731-B2AE-9274F7044201
WARNING:
. The Anti-lock Braking System (ABS) is a
sophisticated device, but it cannot prevent
accidents resulting from careless or danger-
ous driving techniques. It can help maintain
vehicle control during braking on slippery
surfaces. Remember that stopping distances
on slippery surfaces will be longer than on
normal surfaces even with ABS. Stopping
distances may als o be longer on rough,
gravel or snow covered roads, or if you are
using tire chains. Always maintain a safe
distance from the vehicle in front of you.
Ultimately, the driver is r esponsible for
safety.
. Tire type and condition may also affect
braking effectiveness.
— When replacing tires, install the speci-
fied size of tires on all four wheels.
— When installing a spare tire, make sure
that it is the proper size and type as
specified on the tire placard. (See “Tire
placard” (P.9-10).)
— For detailed information, see “Tires and
wheels” (P.8-42).
The Anti-lock Braking System (ABS) controls the
brakes so the wheels do not lock during hard braking
or when braking on slippery surfaces. The system
detects the rotation speed at each wheel and varies
the brake fluid pressure to prevent each wheel from
locking and sliding. By preventing each wheel from
locking, the system helps the driver maintain steering
control and helps to minimize swerving and spinning
on slippery surfaces.
USING SYSTEM
GUID-5FEFFD5B-1E1D-4541-BDEC-F70AF3DC99D0
Depress the brake pedal and hold it down. Depress
the brake pedal with firm steady pressure, but do not
pump the brakes. The ABS will operate to prevent the
wheels from locking up. Steer the vehicle to avoid
obstacles.
WARNING:
Do not pump the brake pedal. Doing so may
result in increased stopping distances.
SELF-TEST FEATURE
GUID-019A1CED-0122-4928-AA4B-48099F192A4E
The ABS includes electronic sensors, electric pumps,
hydraulic solenoids and a computer. The computer has
a built-in diagnostic feature that tests the system each
time you start the engine and move the vehicle at a low
speed in forward or reverse. When the self-test
occurs, you may hear a “clunk” noise and/or feel a
pulsation in the brake pedal. This is normal and does
not indicate a malfunction. If the computer senses a
malfunction, it switches the ABS off and illuminates the
ABS warning light on the instrument panel. The brake
system then operates normally, but without anti-lock
assistance.
If the ABS warning light illuminates during the self-test
or while driving, have the vehicle checked by a
NISSAN dealer.
Starting and driving 5-39
ANTI-LOCK BRAKING SYSTEM
(ABS) (if equipped)
5-40 Starting and driving
NORMAL OPERATION
GUID-051206BD-FEE1-4302-AADE-4D27FFD055FF
The ABS operates at speeds above 5 to 10 km/h (3 to
6 MPH). The speed varies according to road condi-
tions.
When the ABS senses that one or more wheels are
close to locking up, the actuator rapidly applies and
releases hydraulic pressure. This action is similar to
pumping the brakes very quickly. You may feel a
pulsation in the brake pedal and hear a noise from
under the hood or feel a vibration from the actuator
when it is operating. This is normal and indicates that
the ABS is operating properly. However, the pulsation
may indicate that road conditions are hazardous and
extra care is required while driving.
GUID-E637F9EA-B16B-4D4B-8989-3B12ED5C3918
When leaving your vehicle unoccupied:
. Always take the key with you - even when leaving
the vehicle in your own garage.
. Close all windows completely and lock all doors.
. Always park your vehicle where it can be seen.
Park in a well lit area during the night.
. If the security system is equipped, use it - even for
a short period.
. Never leave children or pets in the vehicle
unattended.
. Never leave valuables inside the vehicle. Always
take valuables with you.
. Never leave the vehicle documents in the vehicle.
. Never leave articles on a roof rack. Remove them
from the rack and keep and lock them in a safe
place such as inside the back door.
. Never leave the spare key in the vehicle.
GUID-6BE8FBA3-15D2-4067-BED0-4A209068D889
WARNING:
. Whatever the condition, drive with caution.
Accelerate and decelerate with great care. If
accelerating or decelerating too fast, the
drive wheels will lose even more traction.
. Allow more stopping distance in cold weath-
er driving. Braking should be started sooner
than on dry pavement.
. Keep at a greater distance from the vehicle
in front of you on slippery roads.
. Wet ice (08C, 328F and freezing rain), very
cold snow and ice can be slick and very
difficult to drive on. The vehicle will have a
lot less traction or grip under these condi-
tions. Try to avoid driving on wet ice until the
road is salted or sanded.
. Watch for slippery spots (glaring ice). These
may appear on an otherwise clear road in
shaded areas. If a patch of ice is seen ahead,
brake before reaching it. Try not to brake
while actually on the ice, and avoid any
sudden steering maneuvers.
. Do not use cruise control on slippery roads.
. Snow can trap dangerous exhaust gas under
your vehicle. Keep snow clear of the exhaust
pipe and from around your vehicle.
VEHICLE SECURITY COLD WEATHER DRIVING
BATTERY
GUID-E7A8831C-861E-4CA1-BD1C-B8A4CE00AC86
If the battery is not fully charged during extremely cold
weather conditions, the battery fluid may freeze and
damage the battery. To maintain maximum efficiency,
the battery should be checked regularly. For details,
see “Battery” (P.8-24).
ENGINE COOLANT
GUID-A87A71AB-E3D9-463A-B88C-56630F629BD4
If the vehicle is to be left outside without anti-freeze,
drain the cooling system, including the engine block.
Refill before operating the vehicle. For details, see
“Changing engine coolant” (P.8-10).
TIRE EQUIPMENT
GUID-0D64FA47-EDE9-481D-922A-3C990413C3C0
1. If you have snow tires installed on the front/rear
wheels of your vehicle, they should be of the same
size, loading range, construction and type (bias,
bias-belted or radial) as the rear/front tires.
2. If the vehicle is to be operated in severe winter
conditions, snow tires should be installed on all
four wheels.
3. For additional traction on icy roads, studded tires
may be used. However, some countries, provinces
and states prohibit their use. Check local, state
and provincial laws before installing studded tires.
Skid and traction capabilities of studded
snow tires, on wet or dry surfaces, may be
poorer than that of non-studded snow tires.
4. Snow chains may be used if desired. Make sure
they are the proper size for the tires on your
vehicle and are installed according to the chain
manufacturer’s inst r u c t ions. (Se e “Tire chains”
(P.8-42).)
SPECIAL WINTER EQUIPMENT
GUID-8C87CEB3-FE2A-4488-A369-70B86E4DDB5F
It is recommended that the following items be carried
in the vehicle during the winter:
. A scraper and stiff-bristled brush to remove ice
and snow from the windows.
. A sturdy, flat board to be placed under the jack to
give it firm support.
. A shovel to dig the vehicle out of snowdrifts.
PARKING BRAKE
GUID-E4DAA9B1-767C-481D-ACB6-3B14007778F7
When parking in the area where the outside tempera-
ture is below 08C (328F), do not apply the parking
brake to prevent it from freezing. For safe parking:
. Place the shift lever in the “P” (Park) position
(Automatic Transmission (AT)/Continuously Vari-
able Transmission (CVT) model).
. Place the shift lever in the “ 1” (1s t) or “R”
(Rever se) position (Manual Transmission (MT)
model).
. Securely block the wheels.
CORROSION PROTECTION
GUID-BB3B60D7-BA28-4 375-89D7-CA78B31871D2
Chemicals used for road surface deicing are extremely
corrosive and will accelerate c orrosion and the
deterioration of underbody components such as the
exhaust system, fuel and brake lines, brake cables,
floor pan and fenders.
In the winter, the underbody must be cleaned
periodically. For additional information, see
“Corrosion protection” (P.7-5).
For additional protection against rust and corrosion,
which may be required in some areas, consult a
NISSAN dealer.
Starting and driving 5-41
5-42 Starting and driving
MEMO

Related Topics

Popular Owner Manuals