2004-2009 Nissan Micra 4 Door Starting and driving -> Driving vehicle User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Starting and driving -> Driving vehicle for Your Nissan Micra 4 Door Third Generation (2004-2009)

DIESEL ENGINE
GUID-AA26359D-8901-44E8-AFB1-AB2B2EB2C91F
1. Apply the parking brake.
2. Move the shift lever to the “N” (Neutral) position.
The starter is designed to not operate unless
the clutch pedal is fully depressed.
The Intelligent Key must be carried when
operating the ignition switch.
3. Push the ignition switch to the “ON” position and
wait until the glow plug indicator light turns off.
Depress the clutch pedal and push the ignition
switch to start the engine.
To start the engine immediately, push and release
the ignition switch while depressing the clutch
pedal with the ignition switch in any position.
4. Immediately release the ignition switch when the
engine starts. If the engine starts, but fails to run,
repeat the above procedures.
If the engine is very hard to start in extremely cold
or hot weather, depress the accelerator pedal and
hold it. Push the ignition switch for up to 15
seconds while holding. Release the accelerator
pedal when the engine starts.
CAUTION:
. As soon as the engine has started, release
the ignition switch immediately.
. Do not operate the starter for more than 20
seconds at a time. If the engine does not
start, push the ignition switch to the “OFF”
position and wait 20 seconds before crank-
ing the engine again. Otherwise, the starter
could be damaged.
. If it becomes necessary to start the engine
with a booster battery and jumper cables,
the instructions and cautions contained in
the “6. In case of emergency” section should
be carefully followed.
5. Allow the engine to idle for at least 30 seconds
after starting the engine to warm-up. Drive at
moderate speeds for a short distance first,
especially in cold weather.
CAUTION:
Do not leave the vehicle unattended while the
engine is warming up.
6. To stop the engine, move the shift lever to the “N”
(Neutral) position, apply the parking brake and
push the ignition switch to the “OFF” position.
GUID-ED2CE400-2959-47E0-929D-D3D4E0A10EEC
DRIVING WITH AUTOMATIC TRANSMIS-
SION (AT)
GUID-826D4175-8658-4B2C-BE5F-EBD4979CFB 5F
The Automatic Transmission (AT) in your vehicle is
electronically controlled to produce maximum power
and smooth operation.
The recommended operatin g procedures for this
transmission are shown on the following pages. Follow
these procedures for maximum vehicle performance
and driving enjoyment.
WARNING:
Do not downshift abruptly on slippery roads.
This may cause a loss of control.
CAUTION:
. The cold engine idle speed is high, so use
caution when shifting the transmission into
a forward or reverse position before the
engine has warmed up.
. Avoid revving up the engine while the
vehicle is stopped. This could cause unex-
pected vehicle movement.
. Never shift to either the “P” (Park) or “R”
(Reverse) position while the vehicle is mov-
ing. This could cause serious damage to the
transmission.
. Except in an emergency, do not shift to the
“N” (Neutral) position while driving. Coast-
ing with the transmission in the “N” (Neutral)
position may cause serious damage to the
transmission.
. Start the engine in either the “P” (Park) or
“N” (Neutral) position. The engine will not
start in any other position. If it does, have
Starting and driving 5-11
DRIVING VEHICLE
5-12 Starting and driving
your vehicle checked by a NISSAN dealer.
. Shift into the “P” (Park) position and apply
the parking brake when at a standstill for
longer than a short waiting period.
. Keep the engine at idling speed while
shifting from the “N” (Neutral) position to
any driving position.
. When stopping the vehicle on an uphill
grade, do not hold the vehicle by depressing
the accelerator pedal. The foot brake pedal
should be depressed in this situation.
Starting vehicle
GUID-A34F1624-34DA-4CC6-A351-F7663BEA2BEF
1. After starting the engine, fully depress the foot
brake pedal before shifting the shift lever out of the
“P” (Park) position.
2. Keep the foot brake pedal depressed and move
the shift lever to a driving position.
3. Release the parking brake, the foot brake pedal,
and then gradually start the vehicle in motion.
The AT is designed so the foot brake pedal
MUST be depressed before shifting from the “P”
(Park) position to any driving position while the
ignition switch is in the “ON” position.
The shift lever cannot be moved out of the “P”
(Park) position and into any of the other gear
positions if the ignition switch is turned to the
“LOCK”, “OFF” or “ACC” position or if the key is
removed.
CAUTION:
. DEPRESS THE FOOT BRAKE PEDAL - Shift-
ing the shift lever to “D”, “R”, “2” or “1”
without depressing the foot brake pedal
causes the vehicle to move slowly when
the engine is running. Make sure the foot
brake pedal is depressed fully and the
vehicle is stopped before shifting the shift
lever.
. MAKE SURE OF THE SHIFT LEVER POSI-
TION - Make sure the shift lever is in the
desired position. “D”, “2” and “1” are used to
move forward and “R” to back up.
. WARM UP THE ENGINE - Due to the higher
idle speeds when the engine is cold, extra
caution must be exercised when shifting the
shift lever into the driving position immedi-
ately after starting the engine.
Shifting gear
GUID-5C3474C3-9514 -4881-80AE-66E36F66FBD4
JVS0008X
Left-Hand Drive (LHD) model
JVS0009X
Right-Hand Drive (RHD) model
: Push the button
*
A
while depressing the
foot brake pedal.
: Push the button
*
A
.
: Just move the shift lever.
WARNING:
. Apply the parking brake if the shift lever is in
any position while the engine is not running.
Failure to do so could cause the vehicle to
move unexpectedly or roll away and result in
serious personal injury or property damage.
. If the shift lever cannot be moved from the P
(Park) position while the engine is running
and the foot brake pedal is depressed, the
stop lights may not work. Malfunctioning
stop lights could cause an accident injuring
yourself and others.
After starting the engine, fully depress the foot brake
pedal, push the shift lever button and move the shift
lever out of the P (Park) position.
If the ignition switch is the OFF or ACC position for any
reason while the shift lever is in any positions other
than the P (Park) position, the ignition switch cannot
be turned to the LOCK position.
If the ignition switch cannot be the LOCK position,
perform the following steps:
1. Apply the parking brake.
2. Place the ignition switch in the ON position while
depressing the foot brake pedal.
3. Move the shift lever to the P (Park) position.
4. Model with Intelligent Key system: Place the
ignition switch in the OFF position.
Model without Intelligent Key system: Place the
ignition switch in the LOCK position.
P (Park):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Use this position when the vehicle is parked or when
starting the engine. Make sure that the vehicle is
completely stopped and move the shift lever into
the P (Park) position. Apply the parking brake.
When parking on a hill, apply the parking brake first,
and then move the shift lever into the P (Park) position.
R (Reverse):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Use this position to back up. Make sure that the vehicle
is completely stopped before selecting the R (Reverse)
position.
N (Neutral):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Neither the forward nor reverse gear is engaged. The
engine can be started in this position. You may shift to
the N (Neutral) position and restart a stalled engine
while the vehicle is moving.
D (Drive):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Use this position for all normal forward driving.
2 (Second gear):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Use this position for climbing hills or engine braking on
downhill grades.
1 (Low gear):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Use this position when climbing steep hills slowly or
driving slowly through deep snow, or for maximum
engine braking on steep downhill grades.
Do not shift into the gears when the vehicle speed
exceeds the following limits, otherwise the engine may
over-rev and cause engine damage.
Engine model
Shift lever position
1 2
HR12DE
km/h (MPH)
45 (28) 90 (56)
HR15DE
km/h (MPH)
50 (30)
95 (60)
Overdrive switch
GUID-7D0E15F2-00D5-43C2-BC45-EA894A6F5D44
JVS0013X
Left-Hand Drive (LHD) model
Each time the engine is started, the overdrive function
is automatically reset to “ON”.
“ON” position:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
With the engine running and the shift lever in the “D”
(Drive) position, the transmission upshifts into the
overdrive as vehicle speed increases.
Overdrive does not engage until the engine has
reached operating temperature.
“OFF” position:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
For driving up and down long slopes where engine
braking is necessary, push the overdrive switch. The
overdrive off indicator light
in the meter panel
illuminates.
When cruising at a low speed or climbing a gentle
slope, you may feel uncomfortable shift shocks as the
transmission shifts into and out of the overdrive
repeatedly. In this case, push the overdrive switch to
turn the overdrive “OFF”.
When driving conditions change, push the overdrive
switch to turn the overdrive “ON”. The overdrive off
indicator light will turn off.
Remember not to drive at high speeds for extended
periods of time with the overdrive “OFF”. This reduces
fuel economy.
Accelerator downshift - in D (Drive) position
GUID-9A4FB4A2-7ADC-4D2B-AC49-9E990E768116
For passing or climbing hills, depress the accelerator
pedal to the floor. This shifts the transmission down
into a lower gear, depending on the vehicle speed.
Shift lock release
GUID-C5669C84-95D6-4B8C-85A8-3C7D02F9B4DD
If the battery is discharged, the shift lever may not be
moved from the “P” (Park) position even with the foot
brake pedal depressed.
To move the shift lever, release the shift lock. The shift
lever can be moved to the “N” (Neutral) position.
However, the steering wheel will be locked unless the
ignition switch is placed in the “ON” position. This
Starting and driving 5-13
5-14 Starting and driving
allows the vehicle to be moved if the battery is
discharged.
JVS0014X
Right-Hand Drive (RHD) model
To release the shift lock, perform the follow ing
procedure
1. Models with Intelligent KEY system: Place the
ignition switch in the “OFF” or “LOCK” position.
Models without Intelligent KEY system: Place the
ignition switch in the “LOCK” position and remove
the key.
2. Apply the parking brake.
3. Depress the shift lock release button.
4. Push and hold the shift lever button and move the
shift lever to the “N” (Neutral) position while
holding down the shift lock release button.
5. Place the ignition switch to the “ON” position to
release the steering wheel lock.
The vehicle may be moved, by pushing, to the desired
location.
If the shift lever cannot be moved out of the “P” (Park)
position, have a NISSAN dealer check the AT system
as soon as possible.
Fail-safe
GUID-70726E5E-F30C-457F-B628-89E1EE84479B
When the fail-safe operation occurs, the AT will be
locked in third gear.
If the vehicle is driven under extreme conditions,
such as excessive wheel spinning and subse-
quent hard braking, the fail-safe system may be
activated. This will occur even if all electrical
circuits are functioning properly. In this case,
turn the ignition switch off and wait for 3
seconds. Then turn the ignition switch back to
the “ON” position. The vehicle should return to
its normal operating condition. If it does not
return to its normal operating condition, have a
NISSAN dealer check the transmissi on and
repair it if necessary.
DRIVING WITH CONTINUOUSLY VARI-
ABLE TRANSMISSION (CVT)
GUID-7DB33ED5-E1E C-4DC7-9D8A-BB857680DFD7
The Continuously Variable Transmission (CVT) in your
vehicle is electronically controlled to produce maximum
power and smooth operation.
The recommended operatin g procedures for this
transmission are shown on the following pages. Follow
these procedures for maximum vehicle performance
and driving enjoyment.
WARNING:
Do not downshift abruptly on slippery roads.
This may cause a loss of control.
CAUTION:
. The cold engine idle speed is high, so use
caution when shifting the transmission into
a forward or reverse position before the
engine has warmed up.
. Avoid revving up the engine while the
vehicle is stopped. This could cause unex-
pected vehicle movement.
. Never shift to either the “P” (Park) or “R”
(Reverse) position while the vehicle is mov-
ing. This could cause serious damage to the
transmission.
. Except in an emergency, do not shift to the
“N” (Neutral) position while driving. Coast-
ing with the transmission in the “N” (Neutral)
position may cause serious damage to the
transmission.
. Start the engine in either the “P” (Park) or
“N” (Neutral) position. The engine will not
start in any other position. If it does, have
your vehicle checked by a NISSAN dealer.
. Shift into the “P” (Park) position and apply
the parking brake when at a standstill for
longer than a short waiting period.
. Keep the engine at idling speed while
shifting from the “N” (Neutral) position to
any driving position.
. When stopping the vehicle on an uphill
grade, do not hold the vehicle by depressing
the accelerator pedal. The foot brake pedal
should be depressed in this situation.
Starting vehicle
GUID-10830AE3-53E9-4C49-8A46-50D0BF37D1E3
1. After starting the engine, fully depress the foot
brake pedal before moving the shift lever out of the
“P” (Park) position.
2. Keep the foot brake pedal depressed and move
the shift lever to a driving position.
3. Release the parking brake, the foot brake pedal,
and then gradually start the vehicle in motion.
The CVT is designed so the foot brake pedal
MUST be depressed before shifting from the “P”
(Park) position to any driving position while the
ignition switch is in the “ON” position.
The shift lever cannot be moved out of the “P”
(Park) position and into any of the other
positions if the ignition switch is placed in the
“LOCK”, “OFF” or “ACC” position or if the key is
removed.
CAUTION:
. DEPRESS THE FOOT BRAKE PEDAL - Shift-
ing the shift lever to “D”, “R” or “L” without
depressing the foot brake pedal causes the
vehicle to move slowly when the engine is
running. Make sure the foot brake pedal is
depressed fully and the vehicle is stopped
before shifting the shift lever.
. MAKE SURE OF THE SHIFT LEVER POSI-
TION - Make sure the shift lever is in the
desired position. “D” and “L” are used to
move forward and “R” to back up.
. WARM UP THE ENGINE - Due to the higher
idle speeds when the engine is cold, extra
caution must be exercised when shifting the
shift lever into the driving position immedi-
ately after starting the engine.
JVS0011X
Left-Hand Drive (LHD) model
JVC0026X
Right-Hand Drive (RHD) model
: Push the button
*
A
while depressing the
foot brake pedal.
: Push the button
*
A
.
: Just move the shift lever.
Shifting
GUID-F0518EC1-210F-4737-A790-667D7F0C6B65
WARNING:
. Apply the parking brake if the shift lever is in
any position while the engine is not running.
Failure to do so could cause the vehicle to
move unexpectedly or roll away and result in
serious personal injury or property damage.
. If the shift lever cannot be moved from the
“P” (Park) position while the engine is
running and the foot brake pedal is de-
pressed, the stop lights may not work.
Malfunctioning stop lights could cause an
accident injuring yourself and others.
After starting the engine, fully depress the foot brake
pedal, push the shift lever button and move the shift
lever out of the “P” (Park) position.
If the ignition switch is placed in the “OFF” or “ACC”
position for any reason while the shift lever is in any
positions other than the “P” (Park) position, the ignition
switch cannot be placed in the “LOCK” position.
If the ignition switch cannot be placed in the “LOCK”
position, perform the following steps:
1. Apply the parking brake.
2. Place the ignition switch in the “ON” position
while depressing the foot brake pedal.
3. Move the shift lever to the “P” (Park) position.
4. Models with Intelligent Key system:
Place the ignition switch in the “OFF” position.
Models without Intelligent Key system:
Place the ignition switch in the “LOCK” position.
Starting and driving 5-15
5-16 Starting and driving
P (Park):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Use this position when the vehicle is parked or when
starting the engine. Make sure that the vehicle is
completely stopped and move the shift lever into
the “P” (Park) position. Apply the parking brake.
When parking on a hill, first depress the foot brake
pedal, apply the parking brake, and then move the shift
lever into the “P” (Park) position.
R (Reverse):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Use this position to back up. Make sure that the vehicle
is c ompletely stopped b efore selecting the “R”
(Reverse) position.
N (Neutral):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Neither the forward nor reverse gear is engaged. The
engine can be started in this position. You may shift to
the “N” (Neutral) position and restart a stalled engine
while the vehicle is moving.
D (Drive):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Use this position for all normal forward driving.
L (Low):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
Use this position when climbing steep hills slowly or
driving slowly through deep snow, sand or mud, or for
maximum engine braking on steep downhill grades.
SPORT mode switch
GUID-831EB3E0-330F-44E6-9E2A-935D870A1FD9
JVC0027X
Right-Hand Drive (RHD) model
To select the SPORT mode, push the SPORT mode
switch with the shift lever in the “D” (Drive) position.
The SPORT mode indicator light
in the meter
panel illuminates. To turn off the SPORT mode, push
the SPORT mode switch again. The SPORT mode
indicator light will turn off. When the shift lever is
shifted to any position other than “D”, the SPORT
mode will be automatically turned off.
“OFF” position:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
For normal driving and fuel economy, use the “OFF”
position.
“ON” position:
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
For driving up or down long slopes where engine
braking is necessary, or for powerful acceleration, use
the “ON” position. The transmission will automatically
select a different gear ratio, allowing the engine to
provide high output.
When driving conditions change, push the switch to
turn the SPORT mode off.
Remember not to drive at high speeds for extended
periods of time with the SPORT mode in the “ON”
position. This reduces fuel economy.
Accelerator downshift - in the “D” position -
GUID-1B271593-A574-4815-9738-00C74E37A056
For passing or climbing hills, depress the accelerator
pedal to the floor. This shifts the transmission down
into a lower gear, depending on the vehicle speed.
Shift lock release
GUID-087771B9-AE5C-4 7DB-A6F2-CA2DF8F7C 0E5
JVC0028X
Right-Hand Drive (RHD) model
If the battery charge is low or discharged, the shift
lever may not be moved from the “P” (Park) position
even with the brake pedal depressed and the shift lever
button pushed.
To move the shift lever , perform the following
procedure:
1. Model with Intelligent Key system:
Place the ignition switch in the “OFF” or “LOCK”
position.
Model without Intelligent Key system:
Place the ignition switch in the “LOCK” position,
and remove the key if it is inserted.
2. Apply the parking brake.
3. Depress the shift lock release button.
4. Push the shift lever button and move the shift lever
to the “N” (Neutral) position while holding down
the shift lock release.
5. Place the ignition switch in the “ON” position to
unlock the steering wheel.
The vehicle may be moved to the desired location.
Replace the removed shift lock release cover after the
operation.
For model with Intelligent Key system: If the battery is
discharged completely, the steering wheel cannot be
unlocked. Do not move the vehicle with the steering
wheel locked.
If the shift lever cannot be moved out of the “P” (Park)
position, have a NISSAN dealer check the CVT system
as soon as possible.
WARNING:
If the shift lever cannot be moved from the “P”
(Park) position while the engine is running and
the brake pedal is depressed, the stop lights
may not work. Malfunctioning stop lights could
cause an accident injuring yourself and others.
High fluid temperature protection mode
GUID-72D69A4F-20 B1-4A4F-A0B0-A340C8ABB77F
This transmission has a high fluid temperature protec-
tion mode. If the fluid temperature becomes too high
(for example, when climbing steep grades in high
temperature with heavy loads, such as when towing a
trailer), engine power and, under some conditions,
vehicl e speed wi ll be decreased automatic ally to
reduce the chance of transmission damage. Vehicle
speed can be controlled with the accelerator pedal,
but engine and vehicle speed may be limited.
Fail-safe
GUID-FE30EFD6-3B41-4747-8ECD-CD8D5D3FE6BC
When the fail-safe operation occurs, the CVT will not
be shifted to the selected driving position.
If the vehicle is driven under extreme conditions,
such as excessive wheel spinning and subse-
quent hard braking, the fail-safe system may be
activated. This will occur even if all electrical
circuits are functioning properly. In this case,
place the ignition switch in the “OFF” position
and wait for 10 seconds. Then turn the ignition
switch back to the “ON” position. The vehicle
should return to its normal operating condition.
If it does not return to its normal operating
condition, have a NISSAN dealer check the
transmission and repair it if necessary.
WARNING:
When the fail-safe operation occurs, vehicle
speed may be gradually reduced. The reduced
speed may be lower than other traffic, which
could increase the chance of a collision. Be
especially careful when driving. If necessary, pull
to the side of the road at a safe place and allow
the transmission to return to normal operation,
or have it repaired if necessary.
DRIVING WITH MANUAL TRANSMISSION
(MT)
GUID-94986118-DE97-476D-8073-CD9082003FF5
WARNING:
. Do not downshift abruptly on slippery roads.
This may cause a loss of vehicle control.
. Do not over-rev the engine when shifting to
a lower gear. This may cause a loss of
vehicle control or engine damage.
CAUTION:
. Do not rest your foot on the clutch pedal
while driving. This may damage the clutch
system.
. Fully depress the clutch pedal before shift-
ing to help prevent transmission damage.
. Stop the vehicle completely before shifting
into the “R” (Reverse) position.
. When the vehicle is stopped for a period of
time, for example waiting at stoplights, shift
to the “N” (Neutral) position and release the
clutch p edal with the foot brake pedal
depressed.
. Do not shift to the "N" (Neutral) position
while driving. Doing so may result in an
accident due to loss of engine braking.
Starting and driving 5-17
5-18 Starting and driving
Starting vehicle
GUID-6522A6DD-EA CA-4287-8F91-F52B7E8FF28C
1. After starting the engine, depress the clutch pedal
to the floor and move the shift lever to the “1” (1st)
or “R” (Reverse) position.
2. Slowly depress the accelerator pedal, releasing
the clutch pedal and parking brake at the same
time.
Shifting gear
GUID-A54E0FD6-F94B-4 469-8B26-E47E50C7AA33
SSD0084
To change gears, or when upshifting or downshifting,
fully depress the clutch pedal, shift into the appropriate
gear, then slowly and smoothly release the clutch
pedal.
To ensure smooth gear changes, fully depress the
clutch pedal before operating the shift lever. If the
clutch pedal is not fully depressed before the
transmission is shifted, a gear noise may be heard.
Transmission damage could occur.
Start the vehicle in the “1” (1st) position and shift to
the “2” (2nd), “3” (3rd) , “4” (4th) and “5” (5th) gear in
sequence according to the vehicle speed.
You cannot shift directly from the “5” (5th) position into
the “R” (Reverse) position. First shift into the “N”
(Neutral) position, then shift into the “R” (Reverse)
position.
If it is difficult to move the shift lever into the “R”
(Reverse) or “1” (1st) position, shift to the “N” (Neutral)
position, and then release the clutch pedal once. Fully
depress the clutch pedal again and shift into “R” or “1”.
Suggested maximum speed in each gear
GUID-E0E4461B-F5D4-4 09D-BCA6-C4A5F6920A72
Downshift to a lower gear if the engine is not running
smoothly, or if you need to accelerate.
Do not exceed the maximum suggested speed (shown
below) in any gear. For level road driving, use the
highest gear suggested for that speed. Always observe
posted speed limits, and drive according to the road
conditions which will ensure safe operation. Do not
over-rev the engine when shifting to a lower gear as it
may cause engine damage or loss of vehicle control.
HR12DE engine model (for Micra Active):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
km/h (MPH)
1st 38 (24)
2nd 69 (43)
3rd 101 (63)
4th 128 (80)
5th — (—)
HR12DE engine model (for Thailand, Pakistan,
Brunei, Australia and New Zealand):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
km/h (MPH)
1st 43 (27)
2nd 79 (49)
3rd 116 (72)
4th 157 (97)
5th — (—)
HR12DE engine model (for Europe):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
km/h (MPH)
1st 51 (32)
2nd 93 (58)
3rd 137 (85)
4th 174 (108)
5th — (—)
HR12DE engine model (for Indonesia, Singa-
pore):
GUID-9E14C2E6-2E9C-4731-980B-C45B899B977B
km/h (MPH)
1st 39 (24)
2nd 72 (45)
3rd 105 (66)
4th 143 (89)
5th — (—)

Related Topics

Popular Owner Manuals