2021-2025 Volkswagen Taigo SUV Descriptions of work -> Spark plugs: renewing User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Descriptions of work -> Spark plugs: renewing for Your Volkswagen Taigo SUV First Generation (2021-2025)

Polo 2018 ➤, Polo 2022 ➤, Taigo 2022 ➤  
Maintenance - Edition 10.2021  
ODIS Service  
– Select “No”.  
– Select value for maximum distance to be driven until next oil change service, according to specifications  
valid in your country.  
– Carry out adaptation according to the information of “Guided functions”.  
4.54  
Track rods: checking clearance, at‐  
tachment and boots  
Procedure  
– Check play by moving track rods and wheels with the vehi‐  
cle raised (wheels hanging free). Clearance (specified): no  
clearance:  
– Check that boots -arrow- are not damaged and are seated  
correctly.  
– Make sure that boots -1- of steering rack are not damaged  
and are seated correctly.  
– Perform visual inspection for leaks and damage in area of  
steering rack including track rods.  
4. Descriptions of work  
161  
Polo 2018 ➤, Polo 2022 ➤, Taigo 2022 ➤  
Maintenance - Edition 10.2021  
4.55  
Interior filter: cleaning housing and re‐  
newing filter element  
Procedure  
Note  
♦ Use a dust and pollen filter with at least an activated char‐  
coal layer, ideally an additional allergy filter layer.  
♦ Pollen, soot, fine dust, unpleasant odours, ozone, nitrogen  
oxide and allergies can be filtered out effectively in this way.  
⇒ Heating, air conditioning; Rep. gr. 87; Front heater and air  
conditioning unit; Removing and installing dust and pollen filter.  
4.56  
Transportation mode: switching off  
Note  
♦ The transportation mode is responsible for assuring the  
starting capability of vehicle.  
♦ Battery discharging is reduced by the transportation mode,  
because electrical consumers are switched off.  
♦ All vehicle functions which are not necessarily used during  
vehicle transportation and require no-load voltage or battery  
capacity are switched off with the activated transportation  
mode, with regard to the service life of battery.  
♦ These are especially all functions in the vehicle which can  
reduce the battery capacity when being misused.  
♦ Examples are radios, electronically operated flaps and at‐  
tachments and anti-theft alarm systems which can produce  
faults during transportation.  
– Switch transportation mode off/on ⇒ page 30 .  
4.57  
Transportation devices: removing  
blocking pieces  
Note  
♦ On some models blocking pieces are fitted to the suspen‐  
sion strut piston rod.  
♦ The blocking pieces prevent the springs compressing and  
possible damage to the vehicle when being driven onto a  
vehicle transporter or railway wagon.  
♦ The blocking pieces must be removed without reservation  
before delivering the vehicle. A notice reading “Warning!”  
and attached to the interior rear view mirror highlights this  
point with absolute clarity.  
– Vehicles with blocking pieces fitted to the suspension struts  
have a label hanging from the mirror -arrow-.  
162  
4. Descriptions of work  
Polo 2018 ➤, Polo 2022 ➤, Taigo 2022 ➤  
Maintenance - Edition 10.2021  
Removing blocking pieces on piston rod  
– Relieve weight on coil springs by raising vehicle with a hoist.  
– Slide suspension strut protective sleeve -arrow- upwards.  
Note  
♦ On the front axle, up to 3 blocking pieces are installed on  
each side.  
♦ Usage of any auxiliary means for removal (such as lubricant  
spray, silicone or similar) is not permitted.  
– Push visible blocking piece -arrow- off piston rod.  
– Slightly press in bellows to sense the remaining blocking  
pieces. Slide them downwards on piston rod towards shock  
absorber cap using the folds of the bellows.  
– Push remaining blocking pieces off piston rod.  
– Check bellows -arrows- all-round for dents and rectify any  
dents.  
4. Descriptions of work  
163  
Polo 2018 ➤, Polo 2022 ➤, Taigo 2022 ➤  
Maintenance - Edition 10.2021  
– To rectify dents, slide bellows upwards, reach inside the  
bellows with your hand and press out the dents.  
– Check that bellows are properly engaged in axial bearing:  
♦ Correct position: bellows can be turned around rotational  
axis while seated in axial bearing.  
♦ Otherwise pull bellows all-round out of axial bearing by one  
notch.  
♦ After that, the bellows should be able to be turned around  
rotational axis.  
4.58  
Clock and date: setting  
Setting time and date in Infotainment system  
– Switch on ignition.  
– Switch on Infotainment system.  
– Press CAR function button.  
– Press Setup function button.  
– Press Time and date function button.  
– Select function button Time and set current time.  
– Select function button Date set current date.  
4.59  
Underbody: inspecting for damage to  
underbody sealant, underbody panels,  
routing of lines, plugs  
NOTICE  
During inspection, also check floor pan, wheel housings and  
sills.  
Risk of corrosion and rust penetration.  
– Ensure that all lines are secured in their mountings, all  
plugs are available and there is no visible damage to un‐  
derbody.  
– Faults found must always be rectified (repair measure).  
4.60  
Toothed belt (petrol engines): renewing  
Camshaft drive toothed belt: renewing, petrol engines  
– ⇒ Rep. gr. 15; Toothed belt drive; Removing and installing  
toothed belt  
Coolant pump toothed belt: renewing, petrol engines  
164  
4. Descriptions of work  
Polo 2018 ➤, Polo 2022 ➤, Taigo 2022 ➤  
Maintenance - Edition 10.2021  
– ⇒ Rep. gr. 19; Coolant pump/thermostat assembly  
4.61  
Camshaft drive toothed belt (diesel en‐  
gines): renewing  
TDI common rail engines  
– ⇒ Rep. gr. 15; Toothed belt drive; Removing and installing  
toothed belt  
4.62  
Spark plugs: renewing  
Spark plugs: renewing, 1.0 l PFI engines ⇒ page 166  
Spark plugs: renewing, 1.0 l TSI engines ⇒ page 168  
♦ Only applicable for engine codes: CHZJ, CHZL, DKJA,  
DKLA, DKRA, DKRF, DXUA  
Spark plugs: renewing, 1.0 l TSI engines ⇒ page 171  
♦ Only applicable for engine codes: DLAA, DLAC  
Spark plugs: renewing, 1.5 l TSI engines ⇒ page 174  
Spark plugs: renewing, 1.6 l PFI engines ⇒ page 177  
Spark plugs: renewing, 2.0 l TSI engines ⇒ page 180  
Spark plugs: renewing, 2.0 l TSI engine (engine code DNNA) ⇒  
page 182  
Special tools and workshop equipment required  
♦ Puller -T10530-  
♦ Spark plug socket -3122 B-  
♦ Torque wrench  
4. Descriptions of work  
165  
Polo 2018 ➤, Polo 2022 ➤, Taigo 2022 ➤  
Maintenance - Edition 10.2021  
4.62.1  
Renewing spark plugs, 1.0 l PFI en‐  
gines  
Removing  
– Depending on version, remove air filter housing ⇒ page 97  
or intake air resonator ⇒ 3-cyl. injection engine (1.0 l engine,  
4V, EA 211 EVO); Rep. gr. 24; Air filter; Removing and  
installing intake air resonator.  
– Release connectors -1- and pull them off ignition coils with  
output stages.  
– Remove bolts -2-.  
– Push puller -T10530- as far as stop into hole in ignition coil  
-1-.  
– Tighten knurled nut -2- in -direction of arrow-.  
– Pull ignition coil out of cylinder head cover in direction of  
-arrow- using puller -T10530-.  
166  
4. Descriptions of work  
Polo 2018 ➤, Polo 2022 ➤, Taigo 2022 ➤  
Maintenance - Edition 10.2021  
Repeat step for all ignition coils with output stage.  
– Unscrew spark plugs using spark plug socket and extension  
-3122 B-.  
Installing  
Note  
♦ When installing new spark plugs, regrease ignition coils with  
output stage using silicone paste ⇒ ETKA.  
♦ The applicable silicone paste is stated in the ETKA along  
with the corresponding ignition coil and/or spark plug.  
– Screw in new spark plugs and tighten them to specified tor‐  
que using spark plug socket -3122 B- .  
– Apply a thin bead of silicone paste on the circumference of  
the sealing hose of the ignition coil with output stage -arrow-.  
– Insert ignition coils with output stages into cylinder head.  
4. Descriptions of work  
167  
Polo 2018 ➤, Polo 2022 ➤, Taigo 2022 ➤  
Maintenance - Edition 10.2021  
– Screw in securing bolts -2-, and tighten them to specified  
torque.  
– Fit connectors -1- onto ignition coils with output stages.  
– Install air filter housing ⇒ page 97 .  
Specified torque  
Nm  
22  
8
Spark plugs in cylinder head  
Bolt for ignition coil with output  
stage  
4.62.2  
Renewing spark plugs, 1.0 l TSI en‐  
gines  
♦ Only applicable for engine codes: CHZJ, CHZL, DKJA,  
DKLA, DKRA, DKRF, DXUA  
Removing  
– Remove air filter housing. ⇒ 3-cylinder direct injection engine  
(1.0 l engine, 4V, EA 211, turbocharger); Rep. gr. 24; Air  
filter; Removing and installing air filter housing.  
– Remove air intake pipe. ⇒ 3-cylinder direct injection engine  
(1.0 l engine, 4V, EA 211, turbocharger); Rep. gr. 21;  
Charge air system.  
– Disconnect electrical connector -2-.  
– Unscrew bolt -1-.  
– Push puller -T10530- as far as stop into hole in ignition coil  
-1-.  
168  
4. Descriptions of work  
Polo 2018 ➤, Polo 2022 ➤, Taigo 2022 ➤  
Maintenance - Edition 10.2021  
– Tighten knurled nut -2- in -direction of arrow-.  
– Pull ignition coil out of cylinder head cover in direction of  
-arrow- using puller -T10530-.  
Repeat step for all ignition coils with output stage.  
Note  
♦ Observe installation position of ignition coils with output  
stage!  
♦ Ensure that the cables are not kinked or damaged.  
– Unscrew spark plugs using spark plug socket -3122 B-.  
Note  
Please observe disposal instructions!  
4. Descriptions of work  
169  
Polo 2018 ➤, Polo 2022 ➤, Taigo 2022 ➤  
Maintenance - Edition 10.2021  
Installing  
Note  
♦ When installing new spark plugs, regrease ignition coils with  
output stage using silicone paste ⇒ ETKA.  
♦ The applicable silicone paste is stated in the ETKA along  
with the corresponding ignition coil and/or spark plug.  
– Screw in new spark plugs and tighten them to specified tor‐  
que using spark plug socket -3122 B- ⇒ page 171 .  
– Apply a thin bead of silicone paste on the circumference of  
the sealing hose of the ignition coil with output stage -arrow-.  
– Align and insert all ignition coils with output stage one after  
another loosely into spark plug hole.  
– Press ignition coils with output stage onto spark plugs evenly  
by hand (do not use any tools).  
– Tighten bolt -1- of ignition coil with output stage to specified  
torque ⇒ page 171 .  
– Connect electrical connector -2-.  
Repeat step for all ignition coils with output stage.  
– Further assembly is performed in the reverse order of re‐  
moval.  
170  
4. Descriptions of work  
Polo 2018 ➤, Polo 2022 ➤, Taigo 2022 ➤  
Maintenance - Edition 10.2021  
Specified torque  
Nm  
22  
8
Spark plugs in cylinder head  
Bolt for ignition coil with output stage  
4.62.3  
Renewing spark plugs, 1.0 l TSI en‐  
gines  
♦ Only applicable for engine codes: DLAA, DLAC  
– Remove air intake pipe. ⇒ Rep. gr. 21; Charge air system  
Ignition coil with output stage, cylinder 2  
– Press release button -b- on crankcase breather hose -1-,  
and pull off hose.  
– Carefully push crankcase breather hose -1- to one side.  
Continuation for all cylinders  
– Disconnect electrical connector -2-.  
– Unscrew bolt -1-.  
– Push puller -T10530- as far as stop into hole in ignition coil  
-1-.  
4. Descriptions of work  
171  
Polo 2018 ➤, Polo 2022 ➤, Taigo 2022 ➤  
Maintenance - Edition 10.2021  
– Tighten knurled nut -2- in -direction of arrow-.  
– Pull ignition coil out of cylinder head cover in direction of  
-arrow- using puller -T10530-.  
Repeat step for all ignition coils with output stage.  
Note  
♦ Observe installation position of ignition coils with output  
stage!  
♦ Ensure that the cables are not kinked or damaged.  
– Unscrew spark plugs using spark plug socket -3122 B-.  
Note  
Please observe disposal instructions!  
172  
4. Descriptions of work  
Polo 2018 ➤, Polo 2022 ➤, Taigo 2022 ➤  
Maintenance - Edition 10.2021  
Installing  
Note  
♦ When installing new spark plugs, regrease ignition coils with  
output stage using silicone paste ⇒ ETKA.  
♦ The applicable silicone paste is stated in the ETKA along  
with the corresponding ignition coil and/or spark plug.  
– Screw in new spark plugs and tighten them to specified tor‐  
que using spark plug socket -3122 B- ⇒ page 174 .  
– Apply a thin bead of silicone paste on the circumference of  
the sealing hose of the ignition coil with output stage -arrow-.  
– Align and insert all ignition coils with output stage one after  
another loosely into spark plug hole.  
– Press ignition coils with output stage onto spark plugs evenly  
by hand (do not use any tools).  
– Tighten bolt -1- of ignition coil with output stage to specified  
torque ⇒ page 174 .  
– Connect electrical connector -2-.  
Repeat step for all ignition coils with output stage.  
– Further assembly is performed in the reverse order of re‐  
moval.  
4. Descriptions of work  
173  
Polo 2018 ➤, Polo 2022 ➤, Taigo 2022 ➤  
Maintenance - Edition 10.2021  
Specified torque  
Nm  
22  
8
Spark plugs in cylinder head  
Bolt for ignition coil with output stage  
4.62.4  
Renewing spark plugs, 1.5 l TSI en‐  
gines  
Removing  
– Remove engine cover panel ⇒ page 113 .  
– Remove air pipe ⇒ 4-cylinder direct injection (1.5 l engine,  
4V, EA 211 EVO, turbocharger); Rep. gr. 21; Charge air  
system; Removing and installing air pipe  
– Remove hose on crankcase breather ⇒ 4-cylinder direct in‐  
jection (1.5 l engine, 4V, EA 211 EVO, turbocharger); Rep.  
gr. 17; Crankcase breather.  
– Disconnect electrical connectors -2-.  
– Unscrew bolts -1-.  
– Push puller -T10530- as far as stop into hole in ignition coil  
-1-.  
– Tighten knurled nut -2- in -direction of arrow-.  
– Pull ignition coil out of cylinder head cover in direction of  
-arrow- using puller -T10530-.  
174  
4. Descriptions of work  
Polo 2018 ➤, Polo 2022 ➤, Taigo 2022 ➤  
Maintenance - Edition 10.2021  
Repeat step for all ignition coils with output stage.  
Note  
♦ Observe installation position of ignition coils with output  
stages!  
♦ Ensure that the cables are not kinked or damaged.  
– Unscrew spark plugs using spark plug socket -3122 B-.  
Installing  
Note  
♦ When installing new spark plugs, regrease ignition coils with  
output stage using silicone paste ⇒ ETKA.  
♦ The applicable silicone paste is stated in the ETKA along  
with the corresponding ignition coil and/or spark plug.  
– Screw in new spark plugs and tighten them to specified tor‐  
que using spark plug socket -3122 B- ⇒ page 176 .  
4. Descriptions of work  
175  
Polo 2018 ➤, Polo 2022 ➤, Taigo 2022 ➤  
Maintenance - Edition 10.2021  
– Apply a thin bead of silicone paste on the circumference of  
the sealing hose of the ignition coil with output stage -arrow-.  
– Align and insert all ignition coils with output stage one after  
another loosely into spark plug hole.  
– Press ignition coils with output stage onto spark plugs evenly  
by hand (do not use any tools).  
– Tighten bolt -1- of ignition coil with output stage to specified  
torque ⇒ page 176 .  
– Connect connector -2-.  
Repeat step for all ignition coils with output stage.  
– Further assembly is performed in the reverse order of re‐  
moval.  
Specified torque  
Nm  
22  
8
Spark plugs in cylinder head  
Bolt for ignition coil with output stage  
176  
4. Descriptions of work  
Polo 2018 ➤, Polo 2022 ➤, Taigo 2022 ➤  
Maintenance - Edition 10.2021  
4.62.5  
Renewing spark plugs, 1.6 l PFI en‐  
gines  
Removing  
– Remove air filter housing. ⇒ 4-cylinder injection engine (1.6 l  
engine); Rep. gr. 24; Air filter; Removing and installing air  
filter housing  
– Disconnect electrical connector -2-.  
– Unscrew bolt -1-.  
– Push puller -T10530- as far as stop into hole in ignition coil  
-1-.  
– Tighten knurled nut -2- in -direction of arrow-.  
– Pull ignition coil out of cylinder head cover in direction of  
-arrow- using puller -T10530-.  
4. Descriptions of work  
177  
Polo 2018 ➤, Polo 2022 ➤, Taigo 2022 ➤  
Maintenance - Edition 10.2021  
Repeat step for all ignition coils with output stage.  
Note  
♦ Observe installation position of ignition coils with output  
stage!  
♦ Ensure that the cables are not kinked or damaged.  
– Unscrew spark plugs using spark plug socket -3122 B-.  
Installing  
Note  
♦ When installing new spark plugs, regrease ignition coils with  
output stage using silicone paste ⇒ ETKA.  
♦ The applicable silicone paste is stated in the ETKA along  
with the corresponding ignition coil and/or spark plug.  
– Screw in new spark plugs and tighten them to specified tor‐  
que using spark plug socket -3122 B- ⇒ page 179 .  
178  
4. Descriptions of work  
Polo 2018 ➤, Polo 2022 ➤, Taigo 2022 ➤  
Maintenance - Edition 10.2021  
– Apply a thin bead of silicone paste on the circumference of  
the sealing hose of the ignition coil with output stage -arrow-.  
– Align and insert all ignition coils with output stage one after  
another loosely into spark plug hole.  
– Press ignition coils with output stage onto spark plugs evenly  
by hand (do not use any tools).  
– Tighten bolt -1- of ignition coil with output stage to specified  
torque ⇒ page 179 .  
– Connect electrical connector -2-.  
Repeat step for all ignition coils with output stage.  
– Install air filter housing. ⇒ 4-cylinder injection engine (1.6 l  
engine); Rep. gr. 24; Air filter; Removing and installing air  
filter housing  
Specified torque  
Nm  
22  
8
Spark plugs in cylinder head  
Bolt for ignition coil with output stage  
4. Descriptions of work  
179  
Polo 2018 ➤, Polo 2022 ➤, Taigo 2022 ➤  
Maintenance - Edition 10.2021  
4.62.6  
Renewing spark plugs, 2.0 l TSI en‐  
gines  
Removing  
– Remove engine cover panel ⇒ page 113 .  
– If fitted, unbolt earth wires -arrows-.  
– Release connectors -1- to -4-, and simultaneously pull all  
connectors off ignition coils with output stage.  
– Unscrew bolts for ignition coils with output stage.  
– Push puller -T10530- as far as stop into hole in ignition coil  
-1-.  
– Tighten knurled nut -2- in -direction of arrow-.  
– Pull ignition coil out of cylinder head cover in direction of  
-arrow- using puller -T10530-.  
180  
4. Descriptions of work  
Polo 2018 ➤, Polo 2022 ➤, Taigo 2022 ➤  
Maintenance - Edition 10.2021  
Repeat step for all ignition coils with output stage.  
Note  
♦ Observe installation position of ignition coils with output  
stages!  
♦ Ensure that the cables are not kinked or damaged.  
– Unscrew spark plugs using spark plug socket -3122 B-.  
Installing  
Note  
♦ When installing new spark plugs, regrease ignition coils with  
output stage using silicone paste ⇒ ETKA.  
♦ The applicable silicone paste is stated in the ETKA along  
with the corresponding ignition coil and/or spark plug.  
– Screw in new spark plugs and tighten them to specified tor‐  
que using spark plug socket -3122 B- ⇒ page 182 .  
4. Descriptions of work  
181  
Polo 2018 ➤, Polo 2022 ➤, Taigo 2022 ➤  
Maintenance - Edition 10.2021  
– Apply a thin bead of silicone paste on the circumference of  
the sealing hose of the ignition coil with output stage -arrow-.  
– Align and insert all ignition coils with output stage one after  
another loosely into spark plug hole.  
– Press ignition coils with output stage onto spark plugs evenly  
by hand (do not use any tools).  
– Tighten bolts of ignition coils with output stage to specified  
torque ⇒ page 182 .  
– Simultaneously connect all connectors.  
– If present, bolt on earth wires.  
– Fit engine cover panel ⇒ page 113 .  
Specified torque  
Nm  
30  
10  
10  
Spark plugs in cylinder head  
Bolt for ignition coil with output stage  
Nut for earth wire  
4.62.7  
Renewing spark plugs, 2.0 l TSI en‐  
gines (engine code DNNA)  
Removing  
– Remove engine cover panel ⇒ page 113 .  
– Remove electrical connector -2- for Lambda probe 1 before  
catalytic converter -GX10- from bracket and disconnect.  
182  
4. Descriptions of work  
Polo 2018 ➤, Polo 2022 ➤, Taigo 2022 ➤  
Maintenance - Edition 10.2021  
– Unscrew nut -2-, and move earth wire -1- clear.  
– Release electrical connectors while simultaneously pull them  
off ignition coils -arrows-.  
– Insert puller -T10530- into hole -1- in ignition coil.  
– Turn knurled nut -2- clockwise -arrow- until puller is fixed in  
position.  
– Using puller -T10530-, carefully pull out ignition coil in verti‐  
cal direction -arrow-.  
4. Descriptions of work  
183  
Polo 2018 ➤, Polo 2022 ➤, Taigo 2022 ➤  
Maintenance - Edition 10.2021  
Repeat step for all ignition coils with output stage.  
Note  
♦ Observe installation position of ignition coils with output  
stages!  
♦ Ensure that the cables are not kinked or damaged.  
– Unscrew spark plugs using spark plug socket -3122 B-.  
Installing  
Note  
♦ When installing new spark plugs, regrease ignition coils with  
output stage using silicone paste ⇒ ETKA.  
♦ The applicable silicone paste is stated in the ETKA along  
with the corresponding ignition coil and/or spark plug.  
– Screw in new spark plugs and tighten them to specified tor‐  
que using spark plug socket -3122 B- ⇒ page 185 .  
184  
4. Descriptions of work  
Polo 2018 ➤, Polo 2022 ➤, Taigo 2022 ➤  
Maintenance - Edition 10.2021  
– Apply a thin bead of silicone paste on the circumference of  
the sealing hose of the ignition coil with output stage -arrow-.  
– Align and insert all ignition coils with output stage one after  
another loosely into spark plug hole.  
– Press ignition coils with output stage onto spark plugs evenly  
by hand (do not use any tools).  
– Tighten bolts of ignition coils with output stage to specified  
torque ⇒ page 185 .  
– Simultaneously connect all connectors.  
– If present, bolt on earth wires -arrows-.  
– Install engine cover panel ⇒ page 113 .  
Specified torque  
Nm  
30  
10  
9
Spark plugs in cylinder head  
Bolt for ignition coil with output stage  
Nut for earth wire  
4. Descriptions of work  
185  

Related Topics

Descriptions of work
Removable towing bracket: checking and cleaning if necessary Swivel joints and suspension link mountings: inspecting Automatic headlight control and static cornering light: checking function Battery (12V): checking battery terminal clamps for secure seating Battery (12V): checking with battery tester Status of battery (12V): reading - sending diagnosis protocol via online connection Front passenger front airbag: checking key switch and ?ON/OFF function? Tyres: checking condition, wear pattern, tyre pressure and tread depth Brake and clutch system: changing brake fluid Brake system and shock absorbers: inspecting for leaks and damage Brake fluid level: checking Checking thickness of pads/linings on front and rear brakes and condition of brake discs/drums Diesel fuel filter: draining Diesel fuel filter: renewing Diesel particulate filter: checking Dual clutch gearbox 0D9: changing gear oil and filter Electric windows: checking positioning (open and close functions) Natural gas system: resetting interval display Natural gas system: visually inspecting natural gas tank for corrosion and leakage Natural gas system: checking wax layer between natural gas fuel tank and fuel tank shut-off valve Natural gas tank: renewing Natural gas filler connection and sealing cap: checking condition, if necessary cleaning and checking seal Fault memory of all systems: reading with vehicle diagnostic tester, correcting possible faults Boots: inspecting Interior and exterior body: inspecting for corrosion with doors and flaps open Poly V-belt: renewing Poly V-belt: checking condition Cooling system: checking frost protection and coolant level Air filter: cleaning housing and renewing filter element Multi-purpose additive for diesel fuel: adding Multi-purpose additive for petrol fuel: adding Engine and components in engine compartment: inspecting for leaks and damage Engine cover panel ?top?: removing and installing Motor compartment cover (noise insulation) ?bottom?: removing and installing Engine oil level: checking Engine oil: draining; renewing oil filter and filling engine oil Engine oil: capacities and specifications up to model year 2020 Engine oil: capacities and specifications as of model year 2021 Panoramic sliding sunroof Road test: performing (driving behaviour, noises, air conditioner etc.) Wheel securing bolts: tightening to specified torque Reducing agent (AdBlue?/DEF): replenishing Reducing agent (AdBlue?/DEF): changing Tyre Pressure Loss Indicator: calibrating Tyre repair set: checking Window wash/wipe system and headlight washer system: checking function Headlight adjustment: checking halogen headlights Headlight adjustment: checking LED headlights (Polo) Headlight adjustment: checking LED headlights (ECO) (Polo PA, Taigo) Headlight adjustment: checking matrix LED headlights Headlight adjustment: checking fog lights Service interval display: resetting Service interval display: recoding Track rods: checking clearance, attachment and boots Interior filter: cleaning housing and renewing filter element Transportation mode: switching off Transportation devices: removing blocking pieces Clock and date: setting Underbody: inspecting for damage to underbody sealant, underbody panels, routing of lines, plugs Toothed belt (petrol engines): renewing Camshaft drive toothed belt (diesel engines): renewing

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot