2019-2026 Lexus UX SUV Using the driving support systems -> Dynamic radar cruise control User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Using the driving support systems -> Dynamic radar cruise control for Your Lexus UX SUV First Generation (2019-2026)

249
4-5. Using the driving support systems
4
Driving
Dynamic radar cruise con-
trol
This dynamic radar cruise control
detects the presence of vehicles
ahead, determines the current
vehicle-to-vehicle distance, and
operates to maintain a suitable dis-
tance from the vehicle ahead. The
desired vehicle-to-vehicle dis-
tance can be set by operating the
vehicle-to-vehicle distance switch.
Use the dynamic radar cruise con-
trol only on highways and express-
ways.
WARNING
■ For safe use
● Driving safely is solely the responsibil-
ity of the driver. Do not overly rely on
this system, and pay careful attention
to the surrounding conditions in order
to ensure safe driving.
● The dynamic radar cruise control pro-
vides driving assistance to reduce the
driver’s burden. However, there are
limitations to the assistance provided.
Read the following items carefully. Do
not overly rely on this system and always
drive carefully.
Conditions under which the system may
not operate correctly: P.255
● Set the speed appropriately according
to the speed limit, traffic flow, road
conditions, weather conditions, etc.
The driver is responsible for confirm-
ing the set speed.
● Even if the system is operating cor-
rectly, the condition of a preceding
vehicle as recognized by the driver
and detected by the system may differ.
Therefore, it is necessary for the driver
to pay attention, assess risks, and
ensure safety. Over-reliance on this
system to drive the vehicle safely may
lead to an accident resulting in death
or serious injury.
■ Precautions for the driving assist sys-
tems
Observe the following precautions, as
there are limitations to the assistance
provided by the system. Over-reliance
on this system may lead to an accident
resulting in death or serious injury.
● Details of support provided for the
driver’s vision
The dynamic radar cruise control is only
intended to help the driver in determin-
ing the distance between the driver’s
own vehicle and a designated preceding
vehicle. It is not a system which allows for
careless or inattentive driving, and is not
a system which assists in poor visibility
conditions.
The driver must pay attention to their
surroundings, even when the vehicle
stops.
● Details of support provided for the
driver’s judgement
The dynamic radar cruise control deter-
mines whether the distance between the
driver’s own vehicle and a designated
preceding vehicle is within a set range. It
is not capable of making any other type
of judgement. Therefore, it is absolutely
necessary for the driver to remain vigi-
lant and to determine whether or not
there is a possibility of danger.
● Details of support provided for the
driver’s operation
250
4-5. Using the driving support systems
WARNING
The dynamic radar cruise control does
not include functions which will prevent
or avoid collisions with vehicles ahead of
your vehicle. Therefore, if there is ever
any possibility of danger, the driver must
take immediate and direct control of the
vehicle and act appropriately in order to
ensure safety.
■ Situations in which the dynamic radar
cruise control should not be used
Do not use the dynamic radar cruise
control in the following situations. As the
system will not be able to provide appro-
priate control, using it may lead to an
accident resulting in death or serious
injury.
● Roads where there are pedestrians,
cyclists, etc.
● When driving on a highway or
expressway entrance or exit
● When the approach warning sounds
frequently
● Situations in which the sensors may not
operate properly: P.218
● When it is necessary to disable the sys-
tem: P.215
251
4-5. Using the driving support systems
4
Driving
Constant speed cruising:
When there are no vehicles ahead
The vehicle drives at the speed set by the driver.
If the set vehicle speed is exceeded while driving down a hill, the set vehicle speed display
will blink and a buzzer will sound.
Deceleration and follow-up cruising
When a preceding vehicle driving slower than the set vehicle speed is detected
When a vehicle is detected driving ahead of your vehicle, the vehicle automatically decel-
erates and if a greater reduction in vehicle speed is necessary, the brakes are applied (the
stop lights will come on at this time). The vehicle is controlled to maintain the vehicle-to-
vehicle distance set by the driver, in accordance with changes in the speed of the preced-
ing vehicle. If vehicle deceleration is not sufficient and the vehicle approaches the vehicle
ahead, the approach warning will sound.
Acceleration
When there are no longer any preceding vehicles driving slower than the set
vehicle speed
The vehicle accelerates until the set vehicle speed is reached and then resumes constant
speed cruising.
Starting off:
If a preceding vehicle stops, the vehicle will also stop (controlled stop). After the
Basic functions
A
B
C
D
252
4-5. Using the driving support systems
preceding vehicle starts off, pressing the “RES” switch or depressing the accelera-
tor pedal will resume follow-up cruising (start off operation). If a start off operation
is not performed, the controlled stop will continue.
■ Meter display
Multi-information display
Set vehicle speed
Indicators
■ Switches
Driving assist mode select switch
Driving assist switch
“+” switch/“RES” switch
“-” switch
Cancel switch
Vehicle-to-vehicle distance switch
■ Setting the vehicle speed
1 Press the driving assist mode select
switch to select Adaptive Cruise
Mode.
The dynamic radar cruise control indicator
will illuminate.
2 Using the accelerator pedal, accel-
erate or decelerate to the desired
vehicle speed (approximately 20
mph [30 km/h] or more), and press
the driving assist switch to set the
set vehicle speed.
The set vehicle speed will be displayed on
the multi-information display.
The vehicle speed at the moment the
switch is released will be the set vehicle
System components
A
B
C
A
B
C
D
E
F
Using the dynamic radar cruise
control
253
4-5. Using the driving support systems
4
Driving
speed.
■ Adjusting the set vehicle speed
Adjusting the set vehicle speed
using the switches
To change the set vehicle speed, press
the “+” switch or “-” switch until the
desired speed is displayed.
1 Increase set vehicle speed
2 Decrease set vehicle speed
Short press adjustment: Press the switch
Long press adjustment: Press and hold the
switch until the desired set vehicle speed is
reached.
The set vehicle speed will increase or
decrease as follows:
For the U.S.A., Hawaii, Guam and
Puerto Rico
Short press adjustment: Increases or
decreases by 1 mph (1.6 km/h) each
time the switch is pressed
Long press adjustment: Increases or
decreases in 1 mph (1.6 km/h) incre-
ments continuously while the switch is
pressed and held
Except for the U.S.A., Hawaii,
Guam and Puerto Rico
Short press adjustment: By 1 km/h (0.6
mph) or 1 mph (1.6 km/h) each time the
switch is pressed
Long press adjustment: Increases or
decreases in 5 km/h (3.1 mph) or 5
mph (8 km/h) increments continuously
while the switch is pressed and held
Increasing the set vehicle speed
using the accelerator pedal
1 Depress the accelerator pedal to
accelerate the vehicle to the
desired vehicle speed.
2 Press the “+” switch.
■ Canceling/resuming control
1 Press the cancel switch or driving
assist switch to cancel control.
Control will also be canceled if the brake
pedal is depressed.
(If the vehicle has been stopped by system
control, depressing the brake pedal will not
cancel control.)
2 Press the “RES” switch to resume
control.
254
4-5. Using the driving support systems
■ Changing the vehicle-to-vehicle
distance
Each time the switch is pressed, the
vehicle-to-vehicle distance setting will
change as follows:
If a preceding vehicle is detected, the
preceding vehicle mark will be dis-
played.
The actual vehicle-to-vehicle distance
varies in accordance with the vehicle
speed. Also, when the vehicle is
stopped by system control, it will be
stopped at a certain distance from the
preceding vehicle, depending on the
situation, regardless of the setting.
■ Operating conditions
● The D shift position is selected.
● The desired set speed can be set when
the vehicle speed is approximately 20
mph (30 km/h) or more.
• If the vehicle speed is set while driving at
below approximately 20 mph (30 km/h),
the set vehicle speed will be approxi-
mately 20 mph (30 km/h).
• If the vehicle speed is set while driving at
a speed that exceeds the system’s upper
limit, the set vehicle speed will be the sys-
tem’s upper limit.
■ Accelerating after setting the vehicle
speed
As with normal driving, acceleration can be
performed by depressing the accelerator
pedal. After accelerating, the vehicle will
return to the set vehicle speed. However,
while in vehicle-to-vehicle distance control
mode, the vehicle speed may decrease to
below the set vehicle speed in order to
maintain the distance from the preceding
vehicle.
■ When the vehicle is stopped by system
control during follow-up cruising
● When the “RES” switch is pressed while
the vehicle is stopped by system control,
if the preceding vehicle starts off within
approximately 3 seconds, follow-up
cruising will resume.
● If the preceding vehicle starts off within
approximately 3 seconds of the vehicle
being stopped by system control, follow-
up cruising will resume.
■ Automatic cancellation of vehicle-to-
vehicle distance control mode
In the following situations, vehicle-to-vehi-
cle distance control mode will be canceled
automatically:
● When the brake control or output
restriction control of a driving support
system operates
(For example: Pre-Collision System,
drive-start control)
● When the parking brake has been oper-
ated
● When the driver’s seat belt is unfastened
Illustra-
tion
Number
Vehicle-
to-vehicle
distance
Approximate Dis-
tance (Vehicle
Speed: 60 mph
[100 km/h])
1 Extra long
Approximately
200 ft. (60 m)
2 Long
Approximately 145
ft. (45 m)
3 Medium
Approximately 100
ft. (30 m)
4 Short
Approximately 85
ft. (25 m)
A
255
4-5. Using the driving support systems
4
Driving
while driving
● When the Pre-Collision System is dis-
abled
● When the vehicle is stopped by system
control on a steep incline
● When any of the following are detected
while the vehicle is stopped by system
control:
• The driver’s seat belt is unfastened
• The driver’s door is opened
• Approximately 3 minutes have elapsed
since the vehicle was stopped
The parking brake may be actived automat-
ically.
● Situations in which some or all of the
functions of the system cannot operate:
P.220
■ Dynamic radar cruise control system
warning messages and buzzers
For safe use: P.215
■ Preceding vehicles that the sensor may
not detect correctly
In the following situations, depending on the
conditions, if the system cannot provide suf-
ficient deceleration or acceleration is nec-
essary, operate the brake pedal or
accelerator pedal.
As the sensor may not be able to correctly
detect these types of vehicles, the approach
warning (P.255) may not operate.
● When a vehicle cuts in front of your vehi-
cle or changes lanes away from your
vehicle extremely slowly or quickly
● When changing lanes
● When a preceding vehicle is driving at a
low speed
● When a vehicle is stopped in the same
lane as the vehicle
● When a motorcycle is traveling in the
same lane as the vehicle
■ Conditions under which the system may
not operate correctly
In the following situations, operate the
brake pedal (or accelerator pedal, depend-
ing on the situation) as necessary.
As the sensor may not be able to correctly
detect a vehicle, the system may not oper-
ate properly.
● When a preceding vehicle brakes sud-
denly
● When changing lanes at low speeds,
such as in a traffic jam
In situations where the vehicle
approaches a preceding vehicle and
the system cannot provide sufficient
deceleration, such as if a vehicle cuts in
front of the vehicle, a warning display
will flash and a buzzer will sound to
alert the driver. Depress the brake
pedal to ensure appropriate vehicle-
to-vehicle distance.
■ Warnings may not occur when
In the following situations, the warning
may not operate even though the vehi-
cle-to-vehicle distance is short.
When the preceding vehicle is trav-
eling at the same speed or faster
than your vehicle
When the preceding vehicle is trav-
eling at an extremely low speed
Immediately after the vehicle speed
has been set
When the accelerator pedal is
depressed
When a curve is detected, the vehicle
speed will begin being reduced. When
the curve ends, the vehicle speed
reduction will end.
Depending on the situation, the vehicle
Approach warning
Curve speed reduction function
256
4-5. Using the driving support systems
speed will then return to the set vehicle
speed.
In situations where vehicle-to-vehicle dis-
tance control needs to operate, such as
when a preceding vehicle cuts in front of
your vehicle, the curve speed reduction
function will be canceled.
■ Situations in which the curve speed
reduction function may not operate
In situations such as the following, the curve
speed reduction function may not operate:
● When the vehicle is being driven around
a gentle curve
● When the accelerator pedal is being
depressed
● When the vehicle is being driven around
an extremely short curve
If your vehicle is being driven at
approximately 50 mph (80 km/h) or
more and a lane change to the passing
lane is performed, when the turn signal
lever is operated and the lane is
changed, the vehicle will accelerate up
to the set speed to assist in overtaking.
The system’s recognition of which lane is
the passing lane may be based solely on
the location of the steering wheel in the
vehicle (left-hand drive/right-hand drive).
If the vehicle is driven in a location where
the passing lane is on the opposite side of
that where the vehicle was originally sold,
the vehicle may accelerate when the turn
signal lever is operated away from the
passing lane. (e.g. The vehicle was manu-
factured to be driven on roads for right-
hand drive vehicles [that overtake on the
right], but is being used on roads for left-
hand drive vehicles [that overtake on the
left]. In this case, the vehicle may acceler-
ate when the turn signal lever is operated
to the right.)
If your vehicle is being driven at approxi-
mately 50 mph (80 km/h) or more and
the lane is changed to that with a vehicle
traveling slower than your vehicle, when
the turn signal lever is operated the vehicle
will gradually decelerate to assist in chang-
ing lanes.
The settings of Dynamic radar cruise
control can be changed through cus-
tomize settings. (P.466)
The operating state of Dynamic radar cruise control is indicated.
Support for lane change
Changing Dynamic radar cruise
control settings
Display and system operation state
257
4-5. Using the driving support systems
4
Driving
Indicator Multi-information display Situation
White
Vehicle-to-vehicle
distance setting: Gray
Dynamic radar cruise
control being OFF
Green
Vehicle-to-vehicle
distance setting: Blue
Set vehicle speed:
Green
Constant speed cruis-
ing
Green
Vehicle-to-vehicle
distance setting: Blue
Set vehicle speed:
Green
Preceding vehicle:
White
Follow-up cruising
Green
Vehicle-to-vehicle
distance setting:
Orange flashing
Set vehicle speed:
Green
Preceding vehicle:
Orange flashing
Approach warning
Green
Vehicle-to-vehicle
distance setting: Gray
Set vehicle speed:
White
Preceding vehicle:
Gray
Accelerating with the
accelerator pedal
258
4-5. Using the driving support systems
Green
Set vehicle speed:
Green in reverse dis-
play
Set vehicle speed
being exceeded
Green
Vehicle-to-vehicle
distance setting: Gray
Set vehicle speed:
White
Preceding vehicle:
Gray
Vehicle in controlled
stop
Indicator Multi-information display Situation

Related Topics

Popular Owner Manuals