2006-2014 Nissan Qashqai SUV Pre-driving checks and adjustments -> Security system User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Pre-driving checks and adjustments -> Security system for Your Nissan Qashqai SUV First Generation (2006-2014)

SECURITY SYSTEM  
The ignition circuit is turned on without the own-  
er’s key being used.  
•
ALARM SYSTEM (where fitted)  
NISSAN ANTI-THEFT SYSTEM (NATS)  
The alarm system provides visual and audible alarm  
signals if parts of the vehicle are disturbed.  
The NISSAN Anti-Theft System (NATS)* will not  
allow the engine to start without the use of the reg-  
istered NATS key.  
The alarm system will stop when:  
The vehicle is unlocked using the keyfob unlock  
button.  
•
How to arm the alarm system  
* Immobilizer  
1. Close all doors, windows, back door and bon-  
net.  
The ignition switch or ignition knob is turned to  
the ON position with a registered NATS key.  
•
If the engine fails to start using the registered NATS  
key, it may be due to interference from another  
NATS key, an automated toll road device or an auto-  
mated payment device on the key ring. Restart the  
engine using the following procedure:  
2. Lock the vehicle using the keyfob (lock button),  
for additional information, see “Integrated key-  
fob/remote control system” in the “3. Pre-driving  
checks and adjustments” section.  
If the system does not operate as described  
above, have it checked by your NISSAN dealer or  
qualified workshop.  
1. Leave the ignition switch in the ON position for  
approximately 5 seconds.  
Ultrasonic sensors (where fitted)  
NOTE  
The ultrasonic sensors (volumetric sensing) detect  
movements in the passenger’s compartment. When  
the alarm system is set to the armed position, it will  
automatically switch on the ultrasonic sensors.  
If the vehicle is not fully locked, a door/bonnet/  
back door is open, or the ignition switch is in the  
ON position (after arming the system), the buzzer  
will sound. After correctly closing, the buzzer will  
stop.  
2. Turn the ignition switch to the “OFF” or LOCK  
position and wait approximately 5 seconds.  
3. Repeat steps 1 and 2.  
It is possible to exclude the ultrasonic sensors (e.g.  
when leaving pets inside the car).  
4. Restart the engine while holding the device  
(which may have caused the interference) sepa-  
rated from the registered NATS key or NATS  
Intelligent Key (where fitted).  
Alarm system operation  
To exclude the ultrasonic sensors:  
The system will give the following alarm:  
1. Turn the ignition switch 3 times within 7 seconds  
from the “OFF” to the ON position.  
The siren sounds intermittently and all direction  
indicators will flash.  
•
If this procedure allows the engine to start,  
NISSAN recommends placing the registered  
NATS key or NATS Intelligent Key (where fitted)  
on a separate key-ring to avoid interference from  
other devices.  
2. Close the door(s)/bonnet/back door and press  
The alarm automatically turns off after 28 sec-  
onds.  
•
the lock button  
back door.  
on the keyfob to lock all doors/  
The alarm is activated when:  
The ultrasonic sensors are now excluded from the  
alarm system. All other functions of the system re-  
main activated until the alarm system is disarmed  
again.  
The volumetric sensing system (ultrasonic sen-  
sors) is triggered.  
•
Any door/the back door is opened.  
•
•
The bonnet is opened.  
Pre-driving checks and adjustments 3-13  
Downloaded from manuals search engine  
BONNET RELEASE  
The NATS security indicator light (Type jB ) is  
located on the Driver’s side of the dashboard  
and blinks whenever the ignition switch is in the  
LOCK, “OFF” or Acc position.  
•
If the NISSAN Anti-Theft System (NATS) is mal-  
functioning, this light will remain on while the ignition  
switch is in the ON position.  
If the light remains on and/or the engine will not  
start, see your NISSAN dealer for NATS service  
as soon as possible. Please bring all NATS keys  
or NATS Intelligent Keys when visiting your  
NISSAN dealer for service.  
SIC2045Z  
Meters and gauges (Type A)  
Additional information for RHD models  
If the NATS is malfunctioning, this light will turn on  
after flashing six times while the ignition switch is in  
the ON position.  
However, if the NATS security warning light turns  
off after the light has remained on for 15 minutes,  
there is a 10 second time slot to start the engine  
after the ignition is turned off. See your NISSAN  
dealer for NATS service as soon as possible.  
NIC1402Z  
Driver’s side (Type B)  
NATS security warning/indicator light  
(where fitted)  
One of the following functions (depending on the  
vehicle specifications) indicates that the vehicle is  
equipped with NATS:  
The NATS security warning light (Type A) is lo-  
•
cated in the meter panel and blinks whenever  
the ignition switch is in the LOCK, “OFF” or Acc  
position.  
NPA1002  
3-14 Pre-driving checks and adjustments  
Downloaded from manuals search engine  

Related Topics

Popular Owner Manuals