Get Using the system -> Universal telephone preinstallation GSM II* Guide for Skoda Octavia 4 Door Second Generation (2004-2012)

142 Communication

Mobile phones and two-way radio systems

Note

Please also refer to the operating instructions of the mobile phones and two-way

radio systems.

The installation of a mobile phone and two-way radio system in a vehicle should

only be carried out by an authorised Škoda Service Partner.

Škoda Auto permits the operation of mobile phones and two-way radio systems

with a professionally installed external aerial and a maximum transmission power

of up to 10 watts.

Universal telephone preinstallation GSM II*

It is essential that you inform a specialist garage about the possibilites to assemble

and operate mobile phones and two-way radio sets which have a power output of

more than 10 W. They will inform you which technical possibilities exist for retrofit-

ting mobile telephones and radio transmitters.

Introduction

This enables you to make full use of the advantages of a normal carphone (“hands-

free system - Hands Free” using a microphone integrated in the vehicle, optimal

transmission of signals using an external aerial etc.). The equipment includes

14)

Operation of mobile phones or two-way radio systems may interfere with func-

tioning of the electronic systems of your vehicle. The reasons for this may be:

also the voice control. The telephone is connected by means of the Bluetooth

technology ⇒ page 143, “Bluetooth®”. On vehicles fitted with a telephone

•

no external aerial,

mount*, it is also possible to establish the connection via the interface of the

15)

external aerial incorrectly installed,

transmission power greater than 10 watts.

adapter ⇒ page 145, “Operating telephone calls with the aid of the adapter*.”.

A phone phonebook is part of the mobile phone preinstallation with voice control.

In the phone phonebook there are 1500 free memory locations available. This

phone phonebook is independent of the appliance used for the mobile phone.

You should also be aware of the fact that only an external aerial makes it possible

to achieve the optimal range of such equipment.

Furthermore the volume can be changed individually during the call at any time

with the button for setting the radio* or on vehicles fitted with multifunction

steering wheel* with function buttons on the steering wheel.

WARNING

•

If a mobile phone or a two-way radio system is operated in the vehicle

If the system answers with the voice response “Telephone is not ready”, please

check the operating state of the telephone as follows:

without using a special external aerial or an external aerial which has been

incorrectly installed, this can increase the strength of the electromagnetic

field in the interior of the vehicle.

•

Is the telephone switched on?

Is the PIN code entered?

•

Please concentrate fully at all times on your driving!

You must not install two-way radio systems, mobile phones or mounts

Dialogue

on the covers of the airbags or within the immediate deployment range of

airbags. This might result in injuries to the occupants in the event of an acci-

dent.

The period, in which the telephone system is ready to receive voice commands and

carry out the voice commands, is called DIALOGUE. The system gives audible feed-

back and guides you if necessary through the relevant functions. You can start or

14)

Valid for telephone used with adapter* in the telephone mount.

Not valid for adapter “Bluetooth only” ⇒ page 145.

15)

Communication 143

end the dialogue at any time by pressing the PTT button on the adapter*

Caution

⇒ page 145 or on the multifunction steering wheel* ⇒ page 146.

Taking the mobile phone out of the adapter during the call can lead to interruption

of the connection. When taking out the mobile phone, the connection to the

factory-fitted antenna is interrupted, this reduces the quality of the transmitting

and receiving signal. The charging of the mobile phone battery is also interrupted.

The dialogue is always automatically ended after carrying out an operation, e.g.

after erasing the name from the phonebook.

When receiving an incoming call, the dialogue is immediately interrupted and you

can accept the call by pressing the button° on the multifunction steering wheel*

⇒ page 146 or by pressing the button for receiving a call directly on your tele-

phone.

Note

•

Please also refer to the additional instructions ⇒ page 142, “Mobile phones

and two-way radio systems”.

Should you have any questions, please contact an authorised Škoda Service

If a voice command is not detected, the system answers with “Sorry?” and a new

entry can be performed. After the 2nd error the system repeats the aid. After the 3rd

error the answer “Cancel” is given and the dialogue is ended.

•

Partner.

Optimum understanding of the voice commands depends on the following

factors:

Bluetooth

•

Speak with a normal tone of voice without intonation and excessive voice

pauses.

The Bluetooth technology serves as cableless connection of a

mobile phone to a hands-free system of your vehicle.

•

Avoid insufficient articulation.

Close the doors, windows and sliding roof, in order to reduce or stop disturbing

exterior noise.

In order to connect a mobile phone with Bluetooth to the hands-free

system, it is necessary to adapt the phone and the hands-free system to

each other. Detailed information on this is provided in the operating

instructions of your mobile phone. The following steps must be carried

out for the connection:

•

It is recommended to speak louder at higher speeds, so that the tone of your

voice is louder than the increased surrounding noise.

•

During the dialogue avoid additional noise in the vehicle, e.g. simultaneously

talking occupants.

•

Do not speak, if the system makes an announcement.

–

Switch on the ignition.

The microphone for voice control is directed to the driver and front passenger.

Therefore the driver and the front passenger can operate the equipment.

Select Bluetooth on the mobile phone and select the menu with

which the mobile phone searches for suitable Bluetooth devices.

–

If the hands-free system on the display of the mobile phone

WARNING

announces Skoda UHV, enter the PIN°1234 within 30 seconds and

16)

Pay attention primarily to the traffic situation! As the driver you are fully

responsible for road safety. Use the telephone system only to such an extent,

so that you are in full control of your vehicle at any time.

wait, until the connection is established.

16)

Some mobile phones have a menu, in which the authorization for establishing a Bluetooth^®

connection is performed via the input of a code. If the input for the authorization is neces-

sary, it must always be performed when re-establishing the Bluetooth connection.

Using the system

Safety

Driving Tips

General Maintenance

Breakdown assistance

Technical Data

144 Communication

While connecting the mobile phone with the hands-free system by means of Blue-

•

Please operate your mobile phone exclusively with a suitable adapter in order

to keep a low radiation in the vehicle.

Inserting the mobile phone into the adapter ensures an optimal sending and

tooth , no other phone can be connected with the hands-free system via Blue-

tooth

•

receiving power and offers at the same time the advantage of the battery charging.

Up to three mobile phones can be connected to the hands-free system by means

of Bluetooth , whereby only one mobile phone can communicate via Bluetooth

•

Note that the range of the Bluetooth connection to the handsfree-system is

with the hands-free system. If a fourth mobile phone is connected to the hands-

limited to the vehicle interior. The range is dependent on local factors, e.g. obstacles

between the devices and interferences with other devices. If your mobile phone is

free-system, then the telephone, which has not been used together with the hands-

free-system for the longest period, is disconnected by means of Bluetooth

e.g. in a jacket pocket, this can lead to difficulties when establishing the Bluetooth

connection with the handsfree-system or the data transfer.

Establish Bluetooth connection

After switching on the ignition, the Bluetooth connection is automatically estab-

16)

Inserting the mobile phone with the adapter*

lished for the already adapted mobile phone . Check on the mobile unit if the

automatic connection was established.

Disconnect Bluetooth connection

After withdrawing the ignition key, the Bluetooth connection is disconnected.

WARNING

•

Pay attention primarily to the traffic situation! As the driver you are fully

responsible for road safety. Use the telephone system only to such an extent,

so that you are in full control of your vehicle at any time - risk of accident!

Fig. 160 Universal prepara-

tion for the phone

•

In the event of air transport, the Bluetooth function of the handsfree-

system must be switched off by a specialist garage!

Only one telephone mount* is factory-fitted. An adapter for the phone

can be purchased from the Škoda original accessories.

Caution

Taking the mobile phone out of the adapter during the call can lead to interruption

of the connection. When taking out the mobile phone, the connection to the

factory-fitted antenna is interrupted, this reduces the quality of the transmitting

and receiving signal. The charging of the mobile phone battery is also interrupted.

Inserting the mobile phone with the adapter

–

First of all push the adapter Ain the direction of arrow ⇒ fig. 160 up

to the stop into the mount. Press the adapter slightly downwards, until

it locks securely into position.

Note

Insert the mobile phone into the adapter A(as specified in manufac-

•

Not valid for all mobile phones which enable a communication via Bluetooth

You can ask at an authorised Škoda Service Partner if your telephone is compatible

with the universal telephone preinstallation GSM II.

turer's instructions).

Communication 145

telephone is connected to the handsfree-system via Bluetooth , this connection is

interrupted.

Removing the mobile phone with the adapter

–

Press simultaneouly the side locks of the mount and remove the

mobile phone and adapter ⇒ page 144, fig. 160.

Adapter “Bluetooth only”

For the adapters which are marked with the “Bluetooth only” logo, the complete

communication between the telephone and the handsfree-system of your vehicle

is carried out only with the help of the Bluetooth technology. If an adapter marked

Operating telephone calls with the aid of the adapter*.

in such a way is inserted in the telephone mount, it only serves for recharging the

battery of the telephone and for transmitting the signal onto the outer vehicle

aerial.

Aside from the button PTT, the button SOS can be found on certain adapters

⇒ fig. 162. This button is without function.

Note

The adapters illustrated are only prime examples.

Fig. 161 Illustration image:

Single-button adapter

Fig. 162 Illustration image:

Two-button adapter

The voice control of the telephone is activated by pressing the button PTT (button

push to talk)  on the adapter ⇒ fig. 161 or ⇒ fig. 162.

If you insert the adapter with the telephone in the telephone mount, the handsfree-

system connects to the telephone by means of the interface of the adapter. If the

Using the system

Safety

Driving Tips

General Maintenance

Breakdown assistance

Technical Data

146 Communication

Operation of the telephone on the multifunction steering wheel*

The driver can set the basic functions of the telephone by simply operating the

buttons located on the steering wheel so that he can concentrate on the traffic situ-

ation without being distracted as little as possible by operating the telephone

⇒ fig. 163.

This applies only if your vehicle has been equipped with the telephone preinstalla-

tion at the factory.

If the side lights are switched on, the buttons on the multifunction steering wheel

are illuminated.

Fig. 163 Multifunction

steering wheel: Control

buttons for the telephone

Overview of the different functions in contrast to the multifunction steering wheel

without mobile phone operation ⇒ page 139.

Button

Action

Operation

Activation and deactivation of the voice control°

(Button PTT - Push to talk)

press briefly

Increase volume

Decrease volume

 turn upwards

 turn downwards

 press briefly

Accept call, terminate call, entry in the main menu of the telephone, list of selected numbers

 press button for a long

Reject call, entry in the main menu of the telephone, list of selected numbers

time

Reach one level higher in the menu (according to the current position in the menu)

Return in the main menu of the information display

 press briefly

 press button for a long

time

press briefly

Confirm menu selection

press button for a long

period of time

Confirming the selected menu point, the following initial letters in the telephone book

The last chosen menu selection, name

The next menu selection, name

 turn upwards

 turn downwards

Communication 147

The buttons operate the functions for the operating mode of the current

telephone.

Voice commands

Voice commands for mobile phone operation

Voice command

Operate the telephone via the information display*

Activity

On vehicles which are factory-fitted with a navigation system* with

voice control, it is only possible to operate the voice control via the

navigation system*. The description on how to operate the voice

control can be found in the operating instructions of your navigation

system*.

After this command the PIN code of the mobile

phone can be entered ⇒ page 148.

ENTER PIN/PIN CODE

DIAL NUMBER

REDIAL

After this command a telephone number can be

entered which establishes a connection to the

requested partner ⇒ page 148.

After this command the last selected telephone

number is selected again ⇒ page 149.

If you select the menu point Telephone on the information display with the aid of

the handwheel A, you can change to the following menus:

Phone book

Last calls

Voice commands for operating the phone phone book

Voice command

SAVE/STORE

Activity

Received calls

Missed calls

After this command a name with its telephone

NAMES/NAME/NUMBE number can be stored in the phone phone book

⇒ page 149.

Phone book

In the menu point Phone book is the list of the loaded contacts from the telephone

memory and the SIM card of the mobile phone. In the phone phonebook there are

1500 free memory locations available.

After this command a telephone number which was

SELECT NAMES/NAME stored under its given name in the phone phone

book can be selected ⇒ page 150.

After this command a name in the phone phone

DELETE NAMES/NAME

book can be erased ⇒ page 150.

Note

The display of texts in the menu Telephone is only possible in German, English,

French, Italian, Spanish and Czech.

LISTEN TO/PLAY

PHONEBOOK

After this command you can listen-in to the phone

phone book ⇒ page 151.

After this command the complete phone book or a

name can be erased ⇒ page 151.

DELETE PHONEBOOK

Using the system

Safety

Driving Tips

General Maintenance

Breakdown assistance

Technical Data

148 Communication

Other possible commands

•

the mobile phone is switched on.

The digits zero to nine are permitted. The system detects no continuous digit

combinations such as twenty-three, but only individually spoken digits (two, three).

After each order of digits (separation through brief voice pause) the detected digits

are repeated.

Voice command

DIAL

Activity

The telephone number is selected.

In addition to the name in the phone book, which is

selected on the information display, a voice recording

is stored to select with the help of the voice com-

mands or the entered PIN code.

Notes for entering the PIN code

STORE

•

When entering a PIN code with more than 8 digits, the system indicates “The

PIN is too long”.

When entering an incorrect PIN code, the system indicates “The PIN is incor-

rect”.

The entered name or the digits are repeated. Then the

system requests with voice response “please pro-

ceed” the entry of further digits or commands.

•

REPEAT

•

If the incorrect PIN code has been entered three times consecutively, the card

The entered name or the last entered order of digits is

erased. Previously entered groups of digits are

repeated. Then the system requests with voice

response “please proceed” the entry of further digits

or commands.

is blocked. With the aid of the personal unblocking code PUK (Personal Unblock

Key), the SIM card can be unblocked. The unblocking code can only be entered

via the phone keypad and not through the voice control.

BACK

Example for entering the PIN code

All entered digits are erased. Then the system

requests with voice response “The number is

deleted. The number please” the entry of further

digits or commands.

Voice command

Announcement

DELETE

ENTER PIN/PIN CODE

e.g. ZERO ONE TWO THREE

“The PIN please”.

“Zero One Two Three”.

CANCEL

The dialogue is ended.

If no entry is put in, the following announcement is made after about 5 seconds.

“Possible commands are: store, repeat,

correct, delete or more digits”.

Enter PIN code

“The PIN is saved”.

(end of dialogue)

STORE

A PIN code must be entered before operating the system.

–

Press the PTT button.

You can interrupt the dialogue at any time by pressing the PTT button or with the

voice command CANCEL.

Give the command ENTER PIN/PIN CODE after the signal tone.

After this command the PIN code can be entered.

The entry of the PIN code is only possible if:

Dial number

•

the ignition is switched on,

–

Press the PTT button.

the mobile phone is in the mount,

Using the system -> Universal telephone preinstallation GSM II* for Your Skoda Octavia 4 Door Second Generation (2004-2012)

Related Topics

Popular Owner Manuals

Latest Owner Manuals