2024-2025 Volkswagen Multivan SUV Seatframes -> Assembly overview ? front seat User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Seatframes -> Assembly overview ? front seat for Your Volkswagen Multivan SUV Seventh Generation (2024-2025)

Multivan 2025 ➤ , Multivan 2022 ➤  
General body repairs, interior - Edition 09.2024  
NOTICE  
Risk of damage from incorrect handling.  
– Do not kink moulded headliner.  
– Release moulded headliner -1- from door seal beading -2-.  
– Pull moulded headliner -1- in direction of travel out of clips.  
Important  
•
The aid of an additional person is required for the subse‐  
quent work steps.  
– Remove moulded headliner -1- towards side.  
Installing  
Install in reverse order of removal, observing the following:  
– Pull clips -1- out of roof cross members.  
– Insert clips -1- into holder -2- in direction of -arrow-.  
– Make sure that retaining clip -1- is in installation position  
-arrow-.  
Important  
•
The aid of an additional person is required for the subse‐  
quent work steps.  
– Position moulded headliner in front and rear centring ele‐  
ment.  
– Clip in moulded headliner starting at front.  
– Make sure that no electrical wires are trapped.  
8. Roof trims  
181  
Multivan 2025 ➤ , Multivan 2022 ➤  
General body repairs, interior - Edition 09.2024  
8.3.4  
Removing and installing moulded  
headliner, rear, with glass panel  
Special tools and workshop equipment required  
♦ 3 mm drill bit, commercially available  
♦ Drill, commercially available  
♦ Step drill bit, commercially available  
♦ Suitable drill bit 3 mm, commercially available  
♦ hook - 3370-  
lk  
♦ removal wedge - T40233-  
♦ step drill bit, commercially available  
Note  
The moulded headliner is removed along with the vents. The  
vents can only be removed after the moulded headliner has  
been removed.  
The rear moulded headliner with glass panel will henceforth be  
referred to as “moulded headliner”.  
Removing  
– Remove front moulded headliner ⇒ Rep. gr. 70 ; Removing  
and installing moulded headliner .  
– Release C-pillar trims ⇒ Rep. gr. 70 ; Removing and instal‐  
ling C-pillar trim .  
– Remove roof end strip ⇒ Rep. gr. 70 ; Removing and instal‐  
ling roof end strip .  
– Remove individual seats ⇒ Rep. gr. 72 ; Removing and  
installing individual seats .  
– Pull air duct system in D pillar -2- out of moulded headliner  
-1-.  
182  
Rep. gr.70 - Trim, insulation  
Multivan 2025 ➤ , Multivan 2022 ➤  
General body repairs, interior - Edition 09.2024  
Vehicles with operating and display unit for rear air conditioning  
system - E265-  
– Use commercially available plastic wedge to release cover  
with operating and display unit for rear air conditioning sys‐  
tem - E265- -1- far enough to gain access to electrical con‐  
nector.  
– Disconnect electrical connector.  
– Remove cover with operating and display unit for rear air  
conditioning system - E265- -1-.  
All vehicles (continued)  
– Unscrew bolt -1-.  
lk  
– Insert hook - 3370- -2- through opening in net partition re‐  
tainer, and pull net partition mounting -1- to unclip it.  
Important  
•
The net partition mounting must be unclipped at right angles  
to the vent.  
8. Roof trims  
183  
Multivan 2025 ➤ , Multivan 2022 ➤  
General body repairs, interior - Edition 09.2024  
NOTICE  
Risk of damage from incorrect handling.  
– Do not kink moulded headliner.  
– Release moulded headliner from beading of door seal and  
sliding door seal.  
– Detach moulded headliner -1- downwards, in a straight line  
and all around using removal wedge - T40233- -2-.  
Note  
Moulded headliner is held in place by the arrester straps.  
– Release fastener -arrow-, and disconnect electrical connec‐  
tors -1- at rear interior lights/reading lights.  
lk  
Note  
The electrical connectors on the interior lights/reading lights and  
the arrester strap bolts can be accessed between the moulded  
headliner and the roof cross member.  
Note  
The locking element of the electrical connectors on the interior  
lights/reading lights is located on the left-hand side when seen  
in the direction of travel.  
– Detach arrester strap -1- from body by unscrewing bolt -2-  
between moulded headliner and roof cross member.  
Important  
•
The aid of an additional person is required for the subse‐  
quent work steps.  
– Remove moulded headliner towards rear.  
– Place moulded headliner on a clean and soft surface.  
184  
Rep. gr.70 - Trim, insulation  

Related Topics

Seatframes
Safety information and repair notes Safety information Repair instructions Front seats Assembly overview ? front backrest Assembly overview ? seat pan Assembly overview ? head restraint Assembly overview ? seat height adjustment Assembly overview ? seat rake adjustment Assembly overview - lumbar support Assembly overview - seat depth adjuster Assembly overview ? folding table Assembly overview ? fire extinguisher Removing and installing front seat Removing and installing seat height adjustment handle Removing and installing seat rake adjustment motor [V243]/[V244] Removing and installing seat height adjuster Removing and installing front backrest Removing and installing head restraint guide Removing and installing lumbar support adjustment switch [E176]/[E177] Removing and installing backrest adjuster Removing and installing backrest cover panel Removing and installing lumbar support adjustment motor V125/V126/V129/V130 Removing and installing seat depth adjuster Removing and installing seat trim bracket Removing and installing seat adjustment control unit Removing and installing seat adjustment operating unit [E470]/[E471] Removing and installing operating unit for memory settings [E464]/[E465] Removing and installing seat trim Removing and installing inner seat trim Removing and installing outer seat trim Removing and installing seat longitudinal adjustment motor [V28]/[V31] Removing and installing fire extinguisher holder Removing and installing folding table Rear seats Assembly overview ? individual seats Assembly overview - locking mechanism Assembly overview - head restraint and head restraint guide Assembly overview - rear seat backrest Assembly overview ? seat rails Removing and installing individual seats Removing and installing head restraint Removing and installing trim for locking mechanism Removing and installing locking mechanism for rear seat backrest, holder Removing and installing centre armrest Removing and installing back panel trim Removing and installing seat rails

Popular Owner Manuals

Audi
Audi
BMW
BMW
Citroen
Citroen
Ford
Ford
Honda
Honda
Peugeot
Peugeot