Get Clutch -> 4.2 Clutch, Removing and Installing Guide for Volkswagen Golf 4 Door Fifth Generation (2003-2008)

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤

6-Speed Manual Transmission 02Q - Edition 05.2013

1 - Dual Mass Flywheel

❑ Removing and instal‐

ling. Refer to ⇒ Rep.

Gr. 13 .

❑ Make sure it fits secure‐

ly on the centering pins

❑ Keep the clutch lining

contact surface free of

grooves, oil and grease.

2 - Clutch Plate

❑ Allocation. Refer to the

Parts Catalog.

❑ Removing and instal‐

ling. Refer to

⇒ “4.2 Clutch, Remov‐

ing and Installing”, page

68 .

❑ Only replace together

with the SAC pressure

plate

❑ Installation position. Re‐

fer to

⇒ Fig. ““Clutch Plate In‐

stalled Position”“ ,

page 69

3 - SAC Pressure Plate

❑ SAC = “Self Adjusting

Clutch”

❑ Only replace together

with the clutch plate

❑ Allocation. Refer to the

Parts Catalog.

❑ Removing and instal‐

ling. Refer to

⇒ “4.2 Clutch, Remov‐

ing and Installing”, page

68 .

❑ Checking the ends of the diaphragm spring. Refer to

⇒ Fig. ““Check the Ends of the Diaphragm Spring”“ , page 69

❑ Checking the spring connection and rivet connections. Refer to

⇒ Fig. ““Checking the Spring Connections and Rivet Connections”“ , page 69

4 - Bolt

❑ M6: 13 Nm

❑ M7: 20 Nm

❑ Loosen or tighten in small steps and in a diagonal sequence.

4.2

Clutch, Removing and Installing

Removing

– Remove the transmission.

– Insert Flywheel Retainer - 3067- to loosen the bolts.

– Loosen the bolt diagonally in small steps.

– Remove the pressure plate and the clutch plate.

Installing

Install in reverse order of removal while. Note the following:

Rep. Gr.30 - Clutch

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤

6-Speed Manual Transmission 02Q - Edition 05.2013

Note

♦ Allocate thrust plate and clutch disc according to the engine

code. Refer to the Parts Catalog.

♦ Check whether there are centering sleeves for the engine/

transmission in the cylinder block; install if necessary.

♦ If the alignment sleeves are missing, it will be difficult to shift,

there will be clutch problems and the transmission may make

noises (loose rattling).

Clutch Plate Installed Position

•

“Getriebeseite” (transmission side) -arrow- faces the trans‐

mission.

Check the Ends of the Diaphragm Spring

•

Wear up to half the thickness of the diaphragm spring

-arrows- is permitted.

Checking the Spring Connections and Rivet Connections

– Check the spring connections -arrows A- for damage and

make sure the rivet connections -arrows B- are tight.

4. Clutch, Servicing, Gasoline

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤

6-Speed Manual Transmission 02Q - Edition 05.2013

Only Check Position of Adjustment Mechanism with New Pres‐

sure Plates

•

Both edges -A- of the adjusting ring must be located between

both notches -arrows B-.

•

If the adjusting ring takes on a different position with new pres‐

sure plates, pressure plate and clutch plate must not be in‐

stalled.

•

With used clutches, the adjusting ring may take on a position

outside of the notches.

Note

♦ Replace clutch plates and pressure plates if the rivets are

damaged or loose.

♦ Replace the pressure plate and the clutch plate together.

♦ Allocate the clutch plate and pressure plate to match the en‐

gine code. Refer to the Parts Catalog.

♦ To reduce odor caused by a burnt clutch, thoroughly clean the

clutch housing, the flywheel and the side of the engine facing

toward the transmission.

♦ Clean input shaft splines and (on used clutch plates) the hub

splines, remove corrosion and apply a very thin coating of

Grease for Clutch Disc Shaft Splines - G 000 100- to the

splines. Then move the clutch plate back and forth on the input

shaft until the hub moves freely on the shaft. Remove any ex‐

cess grease.

♦ The pressure plates are protected from corrosion and lubrica‐

ted. Only the running surfaces may be cleaned. Otherwise the

service life of the clutch will be shortened considerably.

♦ The pressure plate contact surface and the clutch plate lining

must completely touch the flywheel. Install the bolts.

– Move the Flywheel Retainer - 3067- during installation.

Rep. Gr.30 - Clutch

Golf Variant 2007 ➤ , Golf Variant 2010 ➤ , Jetta 2005 ➤ , Jetta 2011 ➤

6-Speed Manual Transmission 02Q - Edition 05.2013

Engines having A Crankshaft with A Smaller Diameter -arrow-, or

Engines having A Needle Bearing -arrow- in the Crankshaft

Centering the Clutch Disc, Removing and Installing the Pressure

Plate on Engines with A Crankshaft with A Smaller Diameter, or

Engines with A Needle Bearing in the Crankshaft.

Note

Ignore arrows -A and B-.

Continuation for All

– Position the pressure plate on the centering pins.

– Install all the bolts evenly, by hand, until the bolt heads contact

the pressure plate.

– Tighten the bolts in small steps and in diagonal sequence to

prevent damaging the centering holes of the pressure plate

and the centering pins of the dual mass flywheel -item 4-

⇒ Item 4 (page 68) .

– Install the transmission.

4. Clutch, Servicing, Gasoline

Clutch -> 4.2 Clutch, Removing and Installing for Your Volkswagen Golf 4 Door Fifth Generation (2003-2008)

Related Topics

Popular Owner Manuals

Latest Owner Manuals