2006-2014 Nissan Qashqai SUV Starting and driving User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Starting and driving for Your Nissan Qashqai SUV First Generation (2006-2014)

5 Starting and driving  
Running-in schedule ................................................ 5-2  
Before starting the engine........................................ 5-2  
Precautions when starting and driving...................... 5-3  
Exhaust gas (Carbon Monoxide) ......................... 5-3  
On-pavement and off-road driving precautions ......... 5-4  
Three-way catalyst (Petrol engine models)................ 5-4  
To help prevent damage ..................................... 5-4  
Turbocharger system (Diesel engine models)........... 5-5  
Diesel Particulate Filter (DPF) (where fitted)............. 5-5  
Regeneration restrictions .................................... 5-5  
If regeneration fails ............................................. 5-5  
Care when driving ................................................... 5-6  
Engine cold start period...................................... 5-6  
Loading luggage................................................. 5-6  
Driving on wet roads........................................... 5-6  
Driving under winter conditions........................... 5-6  
Ignition switch.......................................................... 5-6  
Manual transmission ........................................... 5-6  
Automatic transmission or Continuously  
Emergency key – Intelligent Key dead battery  
situation.............................................................. 5-10  
NISSAN Anti-Theft System (NATS)..................... 5-10  
Starting the engine................................................... 5-11  
Driving the vehicle.................................................... 5-12  
Driving with manual transmission......................... 5-12  
Driving with automatic transmission or with  
continuously variable transmission (Models  
with manual shift)................................................ 5-14  
Driving with Continuously Variable Transmis-  
sion (CVT) (Models without manual shift) ............ 5-17  
Stop/Start System (where fitted).............................. 5-21  
Normal operation ................................................ 5-21  
Precautions ........................................................ 5-22  
Stop/Start System OFF switch........................... 5-23  
Environmental savings ........................................ 5-23  
Ultrasonic Parking Sensor (where fitted) .................. 5-24  
Four-wheel Drive (4WD) (where fitted)..................... 5-24  
4WD mode operations........................................ 5-25  
4WD shift tips .................................................... 5-25  
4WD Warning light............................................. 5-26  
4WD Mode indicator lights ................................. 5-27  
Driving four-wheel drive (4WD) safely ................. 5-27  
Cruise control (where fitted) .................................... 5-29  
Precautions on cruise control.............................. 5-29  
Cruise control system operations........................ 5-30  
Speed limiter ........................................................... 5-31  
Speed limiter operations ..................................... 5-32  
Parking.................................................................... 5-33  
Trailer towing........................................................... 5-35  
variable transmission........................................... 5-7  
Steering lock ...................................................... 5-7  
Key positions...................................................... 5-7  
NISSAN Anti-Theft System (NATS)..................... 5-7  
Ignition knob (where fitted)....................................... 5-8  
Manual transmission ........................................... 5-8  
Automatic transmission or Continuously  
variable transmission........................................... 5-9  
Steering lock ...................................................... 5-9  
Ignition knob position.......................................... 5-9  
Downloaded from manuals search engine  
Operating precautions ........................................ 5-35  
Tyre pressure ..................................................... 5-36  
Safety chains...................................................... 5-36  
Trailer brakes...................................................... 5-36  
Trailer detection (where fitted) ............................ 5-36  
Installation of coupling device ............................. 5-36  
Vehicle security........................................................ 5-38  
Power steering system............................................. 5-38  
Brake system........................................................... 5-39  
Brake precautions .............................................. 5-39  
Anti-lock Braking System (ABS).......................... 5-39  
Electronic Stability Programme (ESP) system  
(where fitted) ........................................................... 5-40  
Electronic Stability Programme (ESP) OFF  
switch................................................................. 5-42  
Cold weather driving................................................ 5-42  
Battery ............................................................... 5-43  
Engine coolant.................................................... 5-43  
Tyre equipment................................................... 5-43  
Special winter equipment.................................... 5-43  
Corrosion protection........................................... 5-43  
Downloaded from manuals search engine  
RUNNING-IN SCHEDULE  
BEFORE STARTING THE ENGINE  
During the first 1,600 km (1,000 miles), follow these  
recommendations for the future reliability and  
economy of your new vehicle. Failure to follow the  
recommendations may result in shortened engine  
life and reduced engine performance.  
Check the operation of the warning/indicator  
lights when the ignition switch is turned to the  
ON position.  
•
•
WARNING  
The driving characteristics of your vehicle can be  
changed remarkably by any additional load and  
its distribution as well as by adding optional  
equipment (trailer couplings, roof racks, etc.).  
Your driving style and speed have to be adjusted  
accordingly. Especially when carrying heavy  
loads, your speed must be reduced adequately.  
Do not place hard or heavy objects on the dash-  
board or rear parcel shelf in order to prevent  
injury in the event of a sudden stop.  
Avoid driving for long periods at a constant  
speed, either fast or slow.  
•
Do not accelerate at full throttle in any gear.  
•
•
•
•
Avoid quick starts.  
Make sure the area around the vehicle is free of  
obstacles.  
•
Avoid hard braking as much as possible.  
Check fluid levels such as engine oil, coolant,  
•
Do not tow a trailer during the first 800 km (500  
miles).  
brake and clutch fluid, and window washer fluid  
as frequently as possible, at least whenever you  
refuel.  
NOTE  
Models with K9K diesel engine will achieve top  
performance only after approximately 5,000 km  
(3,000 miles).  
Visually inspect tyres for their appearance and  
condition. Also check the tyre pressure for  
proper inflation.  
•
Maintenance items in the “8. Maintenance and  
do-it-yourself” section should be checked peri-  
odically.  
•
Check that all windows and light lenses are  
clean.  
•
Check that all doors are closed.  
•
•
•
•
Position the seat and adjust the head restraints.  
Adjust the inside and outside mirrors.  
Fasten your seat belt and ask all passengers to  
do likewise.  
5-2 Starting and driving  
Downloaded from manuals search engine  
PRECAUTIONS WHEN STARTING  
AND DRIVING  
If you suspect that exhaust fumes are enter-  
ing the vehicle, drive with all windows fully  
open and have the vehicle inspected immedi-  
ately.  
The exhaust system and body should be in-  
spected by a NISSAN dealer or qualified work-  
shop whenever:  
•
•
•
WARNING  
Do not leave children or adults who would  
•
normally require the support of others alone  
in your vehicle. Pets should also not be left  
alone. They could accidentally injure them-  
selves or others through inadvertent opera-  
tion of the vehicle. Also, on hot, sunny days,  
temperatures in a closed vehicle could quickly  
become high enough to cause severe or pos-  
sibly fatal injuries to people or animals.  
–
–
the vehicle is raised for service.  
Do not run the engine in closed spaces, such  
as a garage, for any longer than is absolutely  
necessary.  
you suspect that exhaust fumes are enter-  
ing into the passenger compartment.  
–
–
you notice a change in the sound of the  
exhaust system.  
Do not park the vehicle with the engine run-  
ning for any extended length of time.  
•
•
you have had an accident involving dam-  
age to the exhaust system, underbody, or  
rear of the vehicle.  
Keep the back door closed while driving, oth-  
erwise exhaust gases could be drawn into the  
passenger compartment. If you must drive in  
this way for some reason, take the following  
steps:  
To prevent luggage or packages from sliding  
forward during braking, do not stack anything  
in the cargo area higher than the seatbacks.  
•
Secure all cargo with ropes or straps to pre-  
vent it from sliding or shifting.  
•
1) Open all the windows.  
2) Set the air recirculation mode (  
“OFF” position.  
) to the  
Failure to follow proper seating instructions  
•
see “Seats” in the “1. Safety — seats, seat  
belts and supplemental restraint system” sec-  
tion, could result in serious personal injury in  
an accident or sudden stop.  
3) Set the fan speed control to the maximum  
position to circulate the air.  
If electrical wiring or other cable connections  
must pass to a trailer through the seal of the  
body, follow the manufacturer’s recommen-  
dations to prevent carbon monoxide entry into  
the vehicle.  
•
•
EXHAUST GAS (Carbon Monoxide)  
WARNING  
Do not breathe exhaust gases; they contain  
•
colourless and odourless carbon monoxide.  
Carbon monoxide is a dangerous gas and can  
cause unconsciousness or death.  
When a vehicle has been stopped in an open  
area with its engine running for any significant  
length of time, turn the fan on to force outside  
air into the vehicle.  
Starting and driving 5-3  
Downloaded from manuals search engine  
ON-PAVEMENT AND OFF-ROAD  
DRIVING PRECAUTIONS  
THREE-WAY CATALYST (Petrol  
engine models)  
Utility vehicles have a significantly higher rollover  
rate than other types of vehicles.  
NISSAN GREEN PROGRAM  
Keep your engine tuned up. Malfunctions in  
the ignition, fuel injection, or electrical sys-  
tems can cause over-rich fuel flow into the  
converter, causing it to overheat.  
•
The three-way catalyst is an emission control device  
installed in the exhaust system. In the converter,  
exhaust gases are burned at high temperatures to  
help reduce pollutants.  
They have higher ground clearance than passenger  
cars to make them capable of performing in a wide  
variety of on-pavement and off-road applications.  
This gives them a higher centre of gravity than ordi-  
nary cars. An advantage of higher ground clearance  
is a better view of the road, allowing you to antici-  
pate problems. However, they are not designed for  
cornering at the same speeds as conventional two-  
wheel drive (2WD) vehicles any more than low-slung  
sports cars are designed to perform satisfactorily  
under off-road conditions. If possible, avoid sharp  
turns or abrupt manoeuvres, particularly at high  
speeds. As with other vehicles of this type, failure to  
operate this vehicle correctly may result in loss of  
control or vehicle rollover. In a rollover accident an  
unbelted person is significantly more likely to be  
injured than a person who is wearing a seat belt.  
Avoid driving with an extremely low fuel level.  
Running out of fuel could cause the engine to  
misfire, damaging the three-way catalyst.  
•
•
CAUTION  
The exhaust gas and the exhaust system are  
•
Do not keep driving if the engine misfires, or  
if noticeable loss of performance or other un-  
usual operating conditions are detected. Have  
the vehicle inspected promptly by a NISSAN  
dealer or qualified workshop.  
very hot. While the engine is running, keep  
people or flammable materials away from the  
exhaust pipe.  
Do not stop or park the vehicle over flam-  
mable materials such as dry grass, waste pa-  
per or rags, as they may burn easily.  
•
Do not race the engine while warming it up.  
•
•
Do not push or tow your vehicle to start the  
engine.  
When parking, ensure that people or flam-  
mable materials are kept away from the ex-  
haust pipe.  
•
TO HELP PREVENT DAMAGE  
CAUTION  
Use UNLEADED PETROL ONLY, specifically  
•
the recommended type. For details, see “Ca-  
pacities and recommended fuel/lubricants” in  
the “9. Technical information” section.  
Do not use leaded petrol. Leaded petrol will  
seriously damage three-way catalyst.  
•
Deposits from leaded petrol will seriously re-  
duce the three-way catalyst’s ability to help  
reduce exhaust pollutants.  
5-4 Starting and driving  
Downloaded from manuals search engine  
TURBOCHARGER SYSTEM  
(Diesel engine models)  
DIESEL PARTICULATE FILTER  
(DPF) (where fitted)  
The turbocharger system uses engine oil for lubrica-  
tion and cooling of its rotating components. The tur-  
bocharger turbine turns at extremely high speeds  
and it can reach an extremely high temperature. It is  
essential to maintain a flow of clean oil through the  
turbocharger system. A sudden interruption to the  
oil supply may cause a malfunction in the turbo-  
charger.  
burns-off the accumulated carbon. This regenera-  
tion process is normally automatic and not visible to  
the driver.  
WARNING  
Be careful not to burn yourself with exhaust  
gases.  
•
REGENERATION RESTRICTIONS  
Do not park the vehicle over flammable mate-  
rials such as dry grass, waste paper or rags,  
as they may burn easily.  
•
Driving conditions such as frequent short journeys  
or stop/start driving can result in excessive build up  
of carbon in the filter. When this happens the DPF  
warning light  
will illuminate (and a message  
If the vehicle continues to be driven at a low  
•
To ensure prolonged life and performance of the  
turbocharger, it is essential to comply with the fol-  
lowing maintenance procedure:  
will appear in the vehicle information display, see  
“Vehicle information display” later in this section) to  
inform you that the vehicle must be driven in a par-  
ticular manner to begin regeneration.  
speed with the DPF warning light illuminated,  
the fail-safe will limit engine revolutions and/  
or torque. In this case, the engine oil must be  
replaced and the process of burning accumu-  
lated particulate matter must be carried out  
by a NISSAN dealer or qualified workshop.  
Service regeneration is a maintenance item  
and is not covered by the NISSAN warranty.  
CAUTION  
Change the engine oil of the turbo-charged  
When the DPF warning light is illuminated, provided  
that legal and safety conditions allow, the vehicle  
should be driven at a speed of over 60 km/h (37.5  
MPH) until the DPF warning light turns off. This pro-  
cess can take up to 30 minutes to complete.  
•
diesel engine as prescribed. See the sepa-  
rately provided Warranty Information & Main-  
tenance Booklet for additional information.  
Use engine oil for DPF equipped models. For  
•
Use only the recommended engine oil. See  
“Capacities  
•
details, see “Capacities and recommended  
fuel/lubricants” in the “9. Technical  
information” section.  
and  
recommended  
IF REGENERATION FAILS  
fuel/lubricants” in the “9. Technical  
information” section.  
Failure to react to the DPF warning light  
lead to saturation of the DPF system. If this hap-  
pens, the Malfunction Indicator (MI) will also  
illuminate to indicate that a Service Regeneration by  
a NISSAN dealer or qualified workshop is required.  
The engine speed may also be limited to 3,000 rpm  
to protect the DPF system.  
may  
CAUTION  
If the engine has been operating at high rpm  
for an extended period of time, let it idle for a  
few minutes prior to shutdown.  
•
•
The DPF becomes extremely hot after burning  
particulate matter.  
Do not accelerate the engine to high rpm im-  
mediately after starting it.  
NISSAN GREEN PROGRAM  
Some diesel engine models are fitted with a Diesel  
Particulate Filter (DPF), which is a device that re-  
moves carbon (soot) from the exhaust gas. To oper-  
ate effectively, the DPF system must routinely con-  
duct a cleaning operation, called regeneration, that  
NOTE  
Contact a NISSAN dealer or qualified workshop  
to perform a forced regeneration.  
Starting and driving 5-5  
Downloaded from manuals search engine  
CARE WHEN DRIVING  
IGNITION SWITCH  
Driving your vehicle to fit the circumstances is es-  
sential for your safety and comfort. As a driver, you  
should be the one who knows best how to drive in  
the given circumstances.  
DRIVING UNDER WINTER  
CONDITIONS  
Drive safely.  
•
•
Avoid starting off, accelerating or stopping sud-  
ENGINE COLD START PERIOD  
denly.  
Due to the higher engine speeds when the engine is  
cold, extra caution must be exercised when select-  
ing a gear during the engine warm-up period after  
starting the engine.  
Avoid sharp turns or lane changes.  
•
•
•
Avoid sudden steering actions.  
NSD238Z  
Extra distance should be kept from the vehicle in  
front.  
LOADING LUGGAGE  
Loads, their distribution and the attachment of equip-  
ment (coupling devices, roof luggage carriers, etc.)  
will change the driving characteristics of the vehicle  
considerably. Driving style and speed must be ad-  
justed accordingly.  
OFF  
j1  
WARNING  
Never remove the key or turn the ignition switch  
to the LOCK position while driving. The steering  
wheel will lock and could cause the driver to lose  
control of the vehicle. This could result in serious  
vehicle damage or personal injury.  
DRIVING ON WET ROADS  
Avoid starting off, accelerating and stopping sud-  
denly.  
•
The switch includes an anti-theft steering lock de-  
vice.  
Avoid sharp turns or lane changes.  
•
•
Extra distance should be kept from the vehicle in  
front.  
There is an “OFF” position between the LOCK and  
Acc positions, although it is not shown on the lock  
cylinder. When the ignition switch is in the “OFF”  
position, the steering wheel is not locked.  
When water covers the road surface in puddles,  
•
small streams, etc, REDUCE SPEED to prevent  
aquaplaning which will cause skidding and loss  
of control. Worn tyres increase this risk.  
MANUAL TRANSMISSION  
To lock the steering wheel, turn the ignition switch  
to the LOCK position and remove the key from the  
ignition switch, then turn the steering clockwise. To  
5-6 Starting and driving  
Downloaded from manuals search engine  
unlock the steering wheel, insert the ignition key and  
turn it gently while rotating the steering wheel slightly  
right and left.  
When the key cannot be turned toward the LOCK  
position, proceed as follows to remove the key:  
Acc (Accessories) (2)  
This position activates electrical accessories, such  
as the radio, when the engine is not running.  
1. Move the selector lever into the P (Park) posi-  
tion.  
The ignition key can only be removed when the  
switch is in the LOCK position (Normal parking po-  
sition) (0).  
ON (Normal operating position) (3)  
2. Turn the key slightly in the ON direction.  
3. Turn the key towards the LOCK position.  
4. Remove the key.  
This position turns on the ignition system and elec-  
trical accessories.  
AUTOMATIC TRANSMISSION OR  
CONTINUOUSLY VARIABLE  
TRANSMISSION  
START (4)  
STEERING LOCK  
The engine starter activates and the engine will start.  
As soon as the engine has started, release the key  
immediately. It will return to the ON position.  
On Automatic Transmission (AT) or Continuously  
Variable Transmission (CVT) models, the ignition  
lock is designed so that the key cannot be turned to  
LOCK and removed until the selector lever is moved  
to the P (Park) position.  
To lock the steering wheel  
1. Turn the key to the LOCK position.  
2. Remove the key from the ignition switch.  
NOTE  
For vehicles fitted with Stop/Start System:  
3. Turn the steering wheel 1/6 of a turn clockwise  
from the straight up position.  
When the engine is automatically stopped by the  
Stop/Start System the ignition switch can still be  
operated as usual.  
When removing the key from the LOCK position of  
the ignition switch, make sure that the selector lever  
is in the P (Park) position.  
To unlock the steering wheel  
1. Insert the key into the ignition switch.  
At the end of a journey turn the ignition OFF to  
avoid a flat battery. The Stop/Start System does  
not automatically turn ignition off.  
The selector lever can only be moved from the P  
(Park) position when the ignition switch is in the ON  
position and the footbrake pedal is depressed.  
2. Gently turn the key while rotating the steering  
wheel slightly right and left.  
To remove the key from the ignition switch:  
NISSAN ANTI-THEFT SYSTEM (NATS)  
KEY POSITIONS  
1. Move the selector lever into the P (Park) posi-  
tion.  
The NISSAN Anti Theft System (NATS)* will stop  
the engine if someone tries to start the engine with-  
out using the registered NATS key.  
LOCK (Normal parking position) (0)  
The ignition key can only be removed when in this  
position.  
2. Turn the key to the LOCK position.  
* Immobilizer  
3. Remove the key from the ignition switch.  
The steering lock can only be locked in this position.  
If you failed to start the engine using the NATS Key,  
turn the ignition knob to the LOCK position, wait for  
5 seconds and turn the key to the START position  
again to start the engine.  
If the key is removed from the ignition switch, the  
selector lever cannot be moved from the P (Park)  
position.  
“OFF” (1)  
The engine is turned off without locking the steering  
wheel.  
Starting and driving 5-7  
Downloaded from manuals search engine  
IGNITION KNOB (where fitted)  
For additional information, see “NISSAN Anti-Theft  
System (NATS)” in the “3. Pre-driving checks and  
adjustments” section.  
CAUTION  
Make sure you carry the Intelligent Key with  
you when operating the vehicle.  
•
•
•
Never leave the Intelligent Key inside the ve-  
hicle when you leave the vehicle.  
If the Intelligent Key is too far away from the  
driver, the vehicle may not start.  
MANUAL TRANSMISSION  
NSD350  
The ignition lock is designed so that the knob can  
ONLY be turned to the LOCK position when the  
PUSH release button has first been depressed.  
MT models  
jA  
jB  
j1  
j2  
AT/CVT models  
OFF  
NOTE  
The ignition knob warning appears in the ve-  
•
PUSH release button  
hicle information display and the buzzer  
sounds twice when the ignition knob is turned  
to the “OFF” position. Depress the PUSH re-  
lease button j2 , then turn the ignition knob to  
the LOCK position. See “ Ignition knob warn-  
ing (Intelligent Key models)” in the “2. Instru-  
ments and controls” section for further details  
regarding the functionality of the ignition knob  
warning.  
WARNING  
Never turn the ignition knob to the LOCK position  
while driving as the steering wheel will lock. This  
may cause the driver to lose control of the ve-  
hicle and could result in serious damage to the  
vehicle or personal injury.  
The ignition knob includes an anti-theft steering lock  
device.  
When the emergency key is being used, the  
•
PUSH release button j2 must be depressed  
in order to turn the ignition knob to the LOCK  
position although the ignition knob warning  
will not appear and the buzzer will not sound.  
There is an “OFF” position between the LOCK and  
Acc positions, although it is not shown on the lock  
cylinder. When the ignition knob is in the “OFF”  
position, the steering wheel is not locked.  
5-8 Starting and driving  
Downloaded from manuals search engine  
AUTOMATIC TRANSMISSION OR  
CONTINUOUSLY VARIABLE  
TRANSMISSION  
IGNITION KNOB POSITION  
LOCK (Normal parking position) (0)  
The steering lock can only be locked in this position.  
The ignition knob is designed so that it cannot be  
turned to the LOCK position until the selector lever  
is moved to the P (Park) position. The selector lever  
can only be moved from the P (Park) position when  
the ignition knob is in the ON position and the  
footbrake pedal is depressed.  
“OFF” (1)  
The engine can be turned off without locking the  
steering wheel.  
Acc (Accessories) (2)  
This position activates electrical accessories, such  
as the radio, when the engine is not running.  
NOTE  
The ignition knob warning appears and a buzzer  
sounds twice when the ignition knob is turned to  
the “OFF” position. Make sure that the selector  
lever is in the P (Park) position, then turn the igni-  
tion knob to the LOCK position. See “Warnings  
and alerts” in the “2. Instruments and controls”  
section for further details regarding the function-  
ality of the ignition knob warning.  
ON (Normal operating position) (3)  
This position turns on the ignition system and the  
electrical accessories.  
START (4)  
The engine starter activates and the engine will start.  
As soon as the engine has started, release the knob  
immediately. It will return to the ON position.  
STEERING LOCK  
NOTE  
To lock the steering wheel  
For vehicles fitted with Stop/Start System:  
In the LOCK position, turn the steering wheel 1/6 of  
a turn from the straight up position.  
When the engine is automatically stopped by the  
Stop/Start System the ignition knob can still be  
operated as usual.  
To unlock the steering wheel  
Depress the brake pedal, push the ignition knob and  
turn it towards the Acc position while gently rotating  
the steering wheel right or left.  
At the end of a journey turn the ignition OFF to  
avoid a flat battery. The Stop/Start System does  
not automatically turn ignition off.  
Starting and driving 5-9  
Downloaded from manuals search engine  
On AT or CVT models, when the ignition knob can-  
not be turned to the LOCK position, proceed as fol-  
lows:  
Slide the locking pin to the unlock position.  
Remove the Intelligent Key cap as illustrated.  
Unfold the key jA .  
j1  
j2  
j3  
j4  
Remove the ignition knob key slot cap with a  
suitable tool.  
Insert the emergency key jA into the ignition  
switch as illustrated.  
j5  
j6  
j7  
Move the selector lever to the P (Park) posi-  
tion.  
Turn the emergency key slightly in the ON  
direction.  
Turn the emergency key to the LOCK position.  
Remove the emergency key.  
j8  
j9  
If the key is removed from the ignition switch, the  
selector lever cannot be moved from P (Park). The  
selector lever can only be moved from the P  
(Park) position when the ignition knob is in the  
ON position and the footbrake pedal is  
depressed.  
NSD291  
Remove the ignition knob key slot cap with a  
suitable tool.  
j4  
j5  
j6  
EMERGENCY KEY – INTELLIGENT  
KEY DEAD BATTERY SITUATION  
NISSAN ANTI-THEFT SYSTEM (NATS)  
Insert the emergency key jA into the ignition  
Slide the locking pin to the unlock position.  
Remove the Intelligent Key cap as illustrated.  
Unfold the key jA .  
j1  
j2  
j3  
The NISSAN Anti-Theft System (NATS)* will stop  
the engine if someone tries to start the engine with-  
out the registered Intelligent Key.  
switch as illustrated.  
Proceed with the emergency key as described  
in “Ignition switch” earlier in this section.  
* Immobilizer  
5-10 Starting and driving  
Downloaded from manuals search engine  
STARTING THE ENGINE  
If you failed to start the engine using the NATS Intel-  
ligent Key, turn the ignition knob to the LOCK posi-  
tion, wait for 5 seconds and turn the knob to the  
START position again to start the engine.  
1. Apply the handbrake.  
CAUTION  
2. Manual transmission models:  
Make sure you carry the Intelligent Key with  
you when operating the vehicle.  
•
•
Move the gear lever to N (Neutral) position, and  
depress the clutch pedal to the floor while start-  
ing the engine.  
If the Intelligent Key is too far away from  
the driver, the vehicle may not start.  
For additional information, see “NISSAN Anti-Theft  
System (NATS)” in the “3. Pre-driving checks and  
adjustments” section.  
Automatic transmission or Continuously vari-  
able transmission models:  
4. For diesel engine models: Wait until the glow  
indicator light goes out.  
Depress the brake pedal and move the selector  
lever to the P (Park) or N (Neutral) position.  
(P position is preferred).  
5. Crank the engine with your foot on the brake  
pedal, not on the accelerator pedal, by turning  
the ignition switch to START.  
NOTE  
6. Release the ignition switch when the engine  
starts. If the engine starts, but fails to run, repeat  
the above procedure.  
The starter is designed not to operate if the  
selector lever is out of the P (Park) or N (Neu-  
tral) position.  
For petrol engine models:  
NOTE  
3. Models without Intelligent Key:  
Rotate the steering wheel left to right to release  
the ignition lock whilst turning the ignition switch  
to the ON position.  
Models with HR16DE engine:  
If the engine is very hard to start because it is  
flooded, depress the accelerator pedal all the  
way to the floor and hold it. Crank the engine  
for 5-6 seconds and stop. After cranking the  
engine, release the accelerator pedal. Then  
crank the engine with your foot off the accel-  
erator pedal. Release the ignition switch when  
the engine starts. If the engine starts, but fails  
to run, repeat the above procedure.  
Models with Intelligent key:  
MT models  
depressed and/or depress the brake pedal  
then:  
–
keep the clutch pedal  
•
AT or CVT models – depress the brake pedal  
then:  
•
1) Push the ignition knob.  
Models with MR20DE engine:  
2) Rotate the steering wheel left to right to  
release the ignition lock whilst turning the  
ignition knob to the ON position.  
If the engine is very hard to start in extremely  
cold or hot weather, or when restarting, de-  
press the accelerator pedal a little (approxi-  
Starting and driving 5-11  
Downloaded from manuals search engine  
DRIVING THE VEHICLE  
mately 1/3 to the floor) and hold it then crank  
the engine. Release the ignition switch and  
the accelerator pedal when the engine starts.  
DRIVING WITH MANUAL  
TRANSMISSION  
CAUTION  
CAUTION  
Do not rest your foot on the clutch pedal while  
driving. This may cause clutch damage.  
•
Do not operate the starter for more than 15  
seconds at a time. If the engine does not start,  
turn the ignition switch to the “OFF” position  
and wait 10 seconds (Petrol engine models)  
or 20 seconds (Diesel engine models) before  
cranking again, otherwise the starter could be  
damaged.  
•
Stop your vehicle completely before shifting  
into the R (Reverse) position.  
•
When you are shifting from one gear to an-  
•
NSD340  
other, be certain to depress the clutch pedal  
all the way to the floor to avoid clashing or  
chipping the gears.  
5–speed MT  
If it becomes necessary to start the engine  
with a booster battery and jumper leads, the  
instructions and cautions contained in the  
“Jump-starting” in the “6. In case of  
emergency” section should be carefully fol-  
lowed.  
•
Avoid abrupt starts and acceleration for your  
safety.  
•
When quick acceleration is required for some  
•
reason, shift to a lower gear and accelerate  
until the vehicle reaches the maximum speed  
in each gear. Do not exceed the speed limit of  
any gear. Pay special attention when acceler-  
ating or when shifting into a lower gear on  
slippery surfaces. Sudden acceleration or  
down shifting could cause the wheels to skid  
and result in loss of control.  
7. Warm-up  
Allow the engine to idle for at least 30 seconds  
after starting. Drive at moderate speed for a short  
distance first, especially in cold weather.  
NSD292Z  
6–speed MT (where fitted)  
Shifting  
WARNING  
RHD models  
jA  
jB  
j1  
Do not leave the vehicle unattended while the  
engine is warming up.  
LHD models  
Gear lever ring  
To change gears, fully depress the clutch pedal,  
shift into the appropriate gear, then release the  
clutch slowly and smoothly.  
5-12 Starting and driving  
Downloaded from manuals search engine  
To ensure smooth gear changes, fully depress the  
clutch pedal before operating the gear lever. If the  
clutch pedal is not fully depressed before the trans-  
mission is shifted, a gear noise may be heard. This  
could result in damage to the transmission.  
However, the driver remains responsible for decid-  
ing the most suitable gear according to actual ve-  
hicle, road and traffic conditions.  
NOTE  
No arrow is displayed is some circumstances in-  
cluding:  
Start the vehicle in 1st gear and shift through the  
gears in sequence according to the vehicle speed.  
–
–
The actual gear matches recommended gear  
The vehicle speed is approx. 0 km/h  
NIC1639  
Reverse gear:  
Model with Stop/Start System  
To reverse with 5–speed manual transmission,  
•
stop the vehicle and shift the gear lever into the  
N (Neutral) position then to the R (Reverse) posi-  
tion.  
To reverse with 6–speed manual transmission,  
proceed as follows:  
•
1) Stop the vehicle.  
2) Move the gear lever into the N (Neutral) posi-  
tion.  
NIC1648  
3) Pull and hold the gear lever ring j1 up.  
Model without Stop/Start System  
4) Move the gear lever into the R (Reverse) po-  
sition.  
Gear shift indicator (where fitted):  
The gear shift indicator jA located in the lower part  
of the vehicle information display can help to im-  
prove the level of environmentally friendly driving.  
5) Release the gear lever ring and safely drive  
the vehicle backwards.  
Following the gear shift indicator by changing to a  
higher (or lower) gear whenever the UP (or DOWN)  
arrow is displayed may improve fuel economy  
The gear lever ring returns to its original posi-  
tion when the gear lever is moved to the N  
(Neutral) position.  
An UP arrow suggests shifting to a higher gear, a  
down arrow suggests shifting to a lower gear.  
When the gear lever is in the R (Reverse) position,  
either the NISSAN Connect monitor (where fitted)  
Starting and driving 5-13  
Downloaded from manuals search engine  
or the ultra sonic parking sensor (where fitted) will  
be activated. For details, see “Rear-view monitor  
(where fitted)” in the “4. Display screen, heater and  
air conditioner, and audio system” section, “Around  
view monitor (where fitted)” in the “4. Display  
screen, heater and air conditioner, and audio  
system” section or “Ultrasonic Parking Sensor  
(where fitted)” later in this section.  
selector position. If it does, have your vehicle  
checked by a NISSAN dealer or qualified  
workshop.  
Make sure that the selector lever is in the  
desired position. Use the D (Drive), or Manual  
shift mode to move forwards and the R (Re-  
verse) to move backwards. Release the hand-  
brake lever and the footbrake pedal, then de-  
press the accelerator pedal to start the vehicle  
in motion and merge with traffic (avoid abrupt  
starting and spinning the wheels).  
Do not depress the accelerator pedal while  
shifting from P (Park) or N (Neutral) to R (Re-  
verse), D (Drive) or Manual shift modes posi-  
tion. Always depress the brake pedal until  
shifting is completed.  
•
•
If it is difficult to move the gear lever into R (Re-  
verse) or 1st. Shift into N (Neutral), then release the  
clutch pedal. Fully depress the clutch pedal again  
and shift into R (Reverse) or 1st.  
Avoid revving up the engine while the vehicle  
is stopped, this could cause unexpected ve-  
hicle movement [if the selector lever is in the  
R (Reverse), D (Drive), or Manual shift mode  
position] or damage the engine [if the selec-  
tor lever is in the N (Neutral) or P (Park) posi-  
tion].  
•
On an uphill grade, do not hold the vehicle by  
depressing the accelerator pedal. The foot-  
brake should be used for this purpose, in or-  
der to hold the vehicle in place and to prevent  
overheating of the transmission.  
DRIVING WITH AUTOMATIC  
TRANSMISSION OR WITH  
CONTINUOUSLY VARIABLE  
TRANSMISSION (Models with manual  
shift)  
Shift into the N (Neutral) position and apply  
the handbrake when at a standstill for longer  
than a short waiting period.  
•
•
WARM THE ENGINE UP  
•
•
Due to the higher idle speeds when the en-  
gine is cold, extra caution must be taken when  
shifting the selector lever into the driving po-  
sition immediately after starting the engine.  
Keep the engine at idling speed while shifting  
from the N (Neutral) position to any driving  
position.  
CAUTION  
The cold engine idle speed is high, so use  
caution when shifting into a forward or re-  
verse gear before the engine has warmed up.  
•
CAUTION (when starting the vehicle):  
PARKING THE VEHICLE  
DEPRESS THE FOOTBRAKE PEDAL  
•
Depress the footbrake pedal and, once the  
vehicle stops, move the selector lever into the  
P (Park) position, pull the handbrake lever and  
release the footbrake pedal.  
Avoid revving up the engine while the vehicle  
is stopped. This could cause unexpected ve-  
hicle movement.  
When the engine is running, shifting the se-  
lector lever into the R (Reverse), D (Drive) or  
Manual shift mode position without depress-  
ing the brake pedal causes the vehicle to  
move slowly. Be sure the brake pedal is fully  
depressed and the vehicle is stopped, before  
shifting the selector lever.  
•
Driving precautions  
Never shift to P (Park) or R (Reverse) while  
Starting the vehicle  
•
1. After starting the engine, fully depress the foot-  
brake pedal before shifting the selector lever from  
P (Park) to R (Reverse), D (Drive) or Manual shift  
mode.  
the vehicle is moving, this could result in dam-  
age to the transmission.  
BE AWARE OF THE SELECTOR LEVER POSI-  
TION  
•
Start the engine in the P (Park) or N (Neutral)  
position. The engine will not start in any other  
•
5-14 Starting and driving  
Downloaded from manuals search engine  
2. Keep the footbrake pedal depressed and push  
the selector lever button to shift into a driving  
gear.  
and air conditioner, and audio system” section,  
“Around view monitor (where fitted)” in the “4. Dis-  
play screen, heater and air conditioner, and audio  
system” section or “Ultrasonic Parking Sensor  
(where fitted)” later in this section.  
Push the button while depressing the  
brake pedal.  
Push the button to shift.  
3. Release the handbrake and footbrake, then  
gradually start the vehicle in motion by pressing  
the accelerator pedal.  
Shift without depressing the brake  
pedal.  
N (Neutral):  
Neither forward nor reverse gear is engaged. The  
engine can be started in this position. You may shift  
to N and restart a stalled engine while driving the  
vehicle.  
The automatic transmission or continuously variable  
transmission is designed so that the footbrake pedal  
MUST be depressed before shifting from P (Park)  
to any drive position while the ignition switch is ON.  
Push the button to shift into P (Park) or R (Reverse).  
All other positions can be selected without pushing  
the button.  
P (Park):  
D (Drive):  
Use this position when the vehicle is parked or when  
starting the engine. Always make sure that the ve-  
hicle is completely stopped before moving the se-  
lector lever into the P (Park) position. For maximum  
safety, the footbrake pedal must be depressed be-  
fore moving the selector lever into the P (Park) posi-  
tion. Use this position together with the handbrake.  
When parking on a hill, first depress the footbrake  
pedal, apply the handbrake and then shift into the P  
(Park) position.  
Use this position for all normal forward driving.  
NSD323Z  
R (Reverse):  
CAUTION  
NIC1649  
Shifting  
LHD models  
jA  
jB  
Shift into this position only after the vehicle has  
completely stopped.  
Gear shift indicator:  
RHD models  
The gear shift indicator jA located in the lower part  
of the vehicle information display shows the current  
position of the transmission.  
To move the selector lever:  
Use this position to reverse the vehicle.  
When the selector lever is in the R (Reverse) posi-  
tion, either the NISSAN Connect monitor (where fit-  
ted) or the ultra sonic parking sensor (where fitted)  
will be activated. For details, see “Rear-view moni-  
tor (where fitted)” in the “4. Display screen, heater  
It shows the P,R,N,D modes when the transmission  
is in auto mode. It shows the gear number when the  
transmission is in manual mode.  
Starting and driving 5-15  
Downloaded from manuals search engine  
When cancelling manual shift mode, return the  
selector lever to the D (Drive) position. The trans-  
mission returns to the normal driving mode.  
•
•
Manual shift mode  
When the selector lever is shifted from D (Drive) to  
the manual shift gate with the vehicle stopped or  
while driving, the transmission enters manual shift  
mode. Shift range can be selected manually.  
In manual shift mode, the transmission may  
not shift to the selected gear under certain  
circumstances. This helps maintain driving  
performance and reduces the chance of ve-  
hicle damage or loss of control.  
In manual shift mode, the selected gear is displayed  
on the position indicator in the combination meter.  
Shift ranges up or down one by one as follows:  
If the engine is revving up to a hazardous  
speed in manual shift mode, the transmission  
may shift up automatically. When the vehicle  
speed decreases, the transmission automati-  
cally shifts down and shifts to 1st gear before  
the vehicle comes to a stop.  
•
NSD347  
1st ⇔ 2nd ⇔ 3rd ⇔ 4th ⇔ 5th ⇔ 6th  
Cap (where fitted)  
When shifting up, move the selector lever to the  
+ (up) side. (Shifts to higher range).  
•
Shift lock release  
If the battery is discharged, the selector lever can-  
not be moved from the P (Park) position even with  
the brake pedal depressed and the ignition switch in  
the ON position.  
When shifting down, move the selector lever to  
the – (down) side. (Shifts to lower range).  
•
Accelerator downshift – In the D (Drive)  
position  
Moving the selector lever rapidly to the same  
side twice will shift the ranges in succession.  
•
For rapid passing or driving uphill, fully depress the  
accelerator pedal to the floor. This shifts the trans-  
mission down into a lower gear, depending on the  
vehicle speed.  
To move the selector lever, remove the cap j1  
(where fitted) then push the shift lock release button  
jA with a suitable tool j2 (as illustrated) and press  
the selector lever button j3 . It is now possible to  
move the selector lever to the N (Neutral) position  
j4 .  
Use the 1st position when driving slowly on steep  
•
hills, slow driving through deep snow, sand or  
mud, or for maximum engine braking on steep  
downhill grades.  
Use the 2nd, 3rd or 4th position when driving  
steep hills or for engine braking on steep down-  
hill grades.  
•
For your safety, make sure the handbrake is applied  
and the brake pedal is depressed during the opera-  
tion.  
Use the 5th position for driving up or down long  
slopes.  
•
If there is any problem moving the lever out of the P  
(Park) position, have a NISSAN dealer or qualified  
workshop to check the automatic transmission sys-  
tem as soon as possible.  
Use the 6th position for all normal forward driv-  
ing. However, you need to shift down the gears  
when accelerating or passing another vehicle.  
•
5-16 Starting and driving  
Downloaded from manuals search engine  
Avoid revving up the engine while the vehicle  
is stopped. This could cause unexpected ve-  
hicle movement.  
•
•
Fail-safe  
AT models:  
WARNING  
When the fail safe operation occurs, the vehicle  
speed may be lower than other traffic, which  
could increase the chance of a collision. Be es-  
pecially careful when driving. If necessary, drive  
to the side of the road at a safe place and away  
from traffic, to allow the transmission to return to  
normal operation, or have the transmission re-  
paired by a NISSAN dealer or qualified workshop,  
if necessary.  
When the fail-safe operation occurs, the AT CHECK  
indicator light comes on for 2 seconds and the auto-  
matic transmission will be locked in the third gear.  
Have a NISSAN dealer or qualified workshop check  
and repair the transmission.  
Never shift to either the P (Park) or R (Re-  
verse) position while the vehicle is moving.  
This could cause serious damage to the trans-  
mission.  
Start the engine in either the P (Park) or N  
(Neutral) position. The engine will not start in  
any other position. If it does, have your ve-  
hicle checked by a NISSAN dealer or qualified  
workshop.  
•
CVT models:  
When the fail-safe operation occurs, the vehicle  
speed will be decreased automatically to reduce the  
chance of transmission damage. Vehicle speed can  
be controlled with the accelerator pedal, but the  
engine power may be limited. Have a NISSAN dealer  
or qualified workshop check and repair the trans-  
mission.  
DRIVING WITH CONTINUOUSLY  
VARIABLE TRANSMISSION (CVT)  
(Models without manual shift)  
Shift into the P (Park) position and apply the  
handbrake when at a standstill for longer than  
a short waiting period.  
•
•
•
The Continuously Variable Transmission (CVT) in  
your vehicle is electronically controlled to produce  
maximum power and smooth operation.  
Keep the engine at idling speed while shifting  
from the N (Neutral) position to any driving  
position.  
AT or CVT models:  
If the vehicle is driven under extreme conditions,  
such as excessive wheel spinning and subse-  
quent hard braking, the Fail-safe system may be  
activated. This will occur even if all electrical cir-  
cuits are functioning properly. In this case, turn  
the ignition switch “OFF” and wait for 10 sec-  
onds. Then turn the key back to the ON position.  
The vehicle should return to its normal operating  
condition. If it does not return to its normal oper-  
ating condition have your NISSAN dealer or quali-  
fied workshop check the transmission and have  
the transmission repaired by a NISSAN dealer or  
qualified workshop, if necessary.  
The recommended operating procedures for this  
transmission are shown on the following pages. Fol-  
low these procedures for maximum vehicle perfor-  
mance and driving enjoyment.  
When stopping the vehicle on an uphill grade,  
do not hold the vehicle by depressing the ac-  
celerator pedal. The footbrake pedal should  
be depressed in this situation.  
WARNING  
Starting vehicle  
Do not downshift abruptly on slippery roads. This  
may cause a loss of control.  
1. After starting the engine, fully depress the foot-  
brake pedal before moving the selector lever out  
of the P (Park) position.  
CAUTION  
The cold engine idle speed is high, so use  
•
2. Keep the footbrake pedal depressed and move  
the selector lever to a driving position.  
caution when shifting the transmission into a  
forward or reverse position before the engine  
has warmed up.  
3. Release the handbrake, the footbrake pedal, and  
then gradually start the vehicle in motion.  
Starting and driving 5-17  
Downloaded from manuals search engine  
The CVT is designed so the footbrake pedal  
MUST be depressed before shifting from the P  
(Park) position to any driving position while the  
ignition switch is in the ON position.  
Shifting  
WARNING  
Apply the handbrake if the selector lever is in  
any position while the engine is not running.  
Failure to do so could cause the vehicle to  
move unexpectedly or roll away and result in  
serious personal injury or property damage.  
•
•
The selector lever cannot be moved out of the P  
(Park) position and into any of the other posi-  
tions if the ignition switch is placed in the LOCK,  
“OFF” or ACC position or if the key is removed.  
CAUTION  
If the selector lever cannot be moved from  
the P (Park) position while the engine is run-  
ning and the footbrake pedal is depressed,  
the stop lights may not work. Malfunctioning  
stop lights could cause an accident injuring  
yourself and others.  
NSD397  
DEPRESS THE FOOTBRAKE PEDAL - Shifting  
•
Left-Hand Drive (LHD) models  
the selector lever to D, R or L without de-  
pressing the footbrake pedal causes the ve-  
hicle to move slowly when the engine is run-  
ning. Make sure the footbrake pedal is de-  
pressed fully and the vehicle is stopped before  
shifting the selector lever.  
After starting the engine, fully depress the footbrake  
pedal, push the selector lever button and move the  
selector lever out of the P (Park) position.  
MAKE SURE OF THE SELECTOR LEVER POSI-  
•
TION - Make sure the selector lever is in the  
desired position. D and L are used to move  
forward and R to reverse.  
If the ignition switch is placed in the “OFF” or ACC  
position for any reason while the selector lever is in  
any positions other than the P (Park) position, the  
ignition switch cannot be placed in the LOCK posi-  
tion.  
NSD398  
WARM UP THE ENGINE - Due to the higher  
•
Right-Hand Drive (RHD) models  
idle speeds when the engine is cold, extra  
caution must be exercised when shifting the  
selector lever into the driving position imme-  
diately after starting the engine.  
If the ignition switch cannot be placed in the LOCK  
position, perform the following steps:  
Push the button jA while depressing  
the footbrake pedal.  
1. Apply the handbrake.  
Push the button jA .  
2. Place the ignition switch in the ON position while  
depressing the footbrake pedal.  
Just move the selector lever.  
3. Move the selector lever to the P (Park) position.  
4. Models with Intelligent Key system:  
5-18 Starting and driving  
Downloaded from manuals search engine  
Place the ignition switch in the “OFF” position.  
Models without Intelligent Key system:  
Place the ignition switch in the LOCK position.  
L (Low):  
ON position:  
Use this position when climbing steep hills slowly or  
driving slowly through deep snow, sand or mud, or  
for maximum engine braking on steep downhill  
grades.  
For driving up or down long slopes where engine  
braking is necessary, or for powerful acceleration,  
use the ON position. The transmission will automati-  
cally select a different gear ratio, allowing the en-  
gine to provide high output.  
P (Park):  
Use this position when the vehicle is parked or when  
starting the engine. Make sure that the vehicle is  
completely stopped and move the selector lever  
into the P (Park) position. Apply the handbrake.  
When parking on a hill, first depress the footbrake  
pedal, apply the handbrake, and then move the se-  
lector lever into the P (Park) position.  
When driving conditions change, push the switch to  
turn the SPORT mode off.  
Remember not to drive at high speeds for extended  
periods of time with the SPORT mode in the ON  
position. This reduces fuel economy.  
Accelerator downshift  
- in the D position -  
R (Reverse):  
Use this position to reverse. Make sure that the  
vehicle is completely stopped before selecting the R  
(Reverse) position.  
NSD399  
For passing or climbing hills, depress the accelera-  
tor pedal to the floor. This shifts the transmission  
down into a lower gear, depending on the vehicle  
speed.  
Left-Hand Drive (LHD) model  
SPORT mode switch  
When the selector lever is in the R (Reverse) posi-  
tion, either the NISSAN Connect monitor (where fit-  
ted) or the ultra sonic parking sensor (where fitted)  
will be activated. For details, see “Rear-view moni-  
tor (where fitted)” or “Around view monitor (where  
fitted)” earlier in this section or “Ultrasonic Parking  
Sensor (where fitted)” later in this section  
To select the SPORT mode, push the SPORT mode  
switch with the selector lever in the D (Drive) posi-  
tion. The SPORT mode indicator light  
in the  
meter panel illuminates. To turn off the SPORT  
mode, push the SPORT mode switch again. The  
SPORT mode indicator light will turn off. When the  
selector lever is shifted to any position other than D,  
the SPORT mode will be automatically turned off.  
N (Neutral):  
Neither the forward nor reverse gear is engaged.  
The engine can be started in this position. You may  
shift to the N (Neutral) position and restart a stalled  
engine while the vehicle is moving.  
OFF position:  
For normal driving and fuel economy, use the OFF  
position.  
NSD400  
D (Drive):  
Use this position for all normal forward driving.  
Starting and driving 5-19  
Downloaded from manuals search engine  
For models with Intelligent Key system: If the battery  
is discharged completely, the steering wheel cannot  
be unlocked. Do not move the vehicle with the steer-  
ing wheel locked.  
quent hard braking, the fail-safe system may be  
activated. This will occur even if all electrical cir-  
cuits are functioning properly. In this case, place  
the ignition switch in the “OFF” position and wait  
for 10 seconds. Then turn the ignition switch back  
to the ON position. The vehicle should return to  
its normal operating condition. If it does not re-  
turn to its normal operating condition, have a  
NISSAN dealer or qualified workshop check the  
transmission and repair it if necessary.  
Shift lock release  
LHD models  
j1  
j2  
jA  
RHD models  
If the selector lever cannot be moved out of the P  
(Park) position, have a NISSAN dealer or qualified  
workshop check the CVT system as soon as pos-  
sible.  
Shift lock release button  
If the battery charge is low or discharged, the selec-  
tor lever may not move from the P (Park) position  
even with the brake pedal depressed and the selec-  
tor lever button pushed.  
WARNING  
To move the selector lever, perform the following  
procedure:  
If the selector lever cannot be moved from the P  
(Park) position while the engine is running and  
the brake pedal is depressed, the stop lights may  
not work. Malfunctioning stop lights could cause  
an accident injuring yourself and others.  
WARNING  
When the fail-safe operation occurs, vehicle  
speed may be gradually reduced. The reduced  
speed may be lower than other traffic, which  
could increase the chance of a collision. Be es-  
pecially careful when driving. If necessary, pull to  
the side of the road at a safe place and allow the  
transmission to return to normal operation, or  
have it repaired if necessary.  
1. Models with Intelligent Key system:  
Place the ignition switch in the “OFF” or LOCK  
position.  
High fluid temperature protection mode  
Models without Intelligent Key system:  
This transmission has a high fluid temperature pro-  
tection mode. If the fluid temperature becomes too  
high (for example, when climbing steep grades in  
high temperature with heavy loads, such as when  
towing a trailer), engine power and, under some  
conditions, vehicle speed will be decreased auto-  
matically to reduce the chance of transmission dam-  
age. Vehicle speed can be controlled with the ac-  
celerator pedal, but engine and vehicle speed may  
be limited.  
Place the ignition switch in the LOCK position,  
and remove the key if it is inserted.  
2. Apply the handbrake.  
3. Push down the shift lock release button jA . Use  
a suitable tool.  
4. Push and hold the selector lever button and move  
the selector lever to the N (Neutral) position while  
holding down the shift lock release button.  
Place the ignition switch in the ON position to un-  
lock the steering wheel. The vehicle may be moved  
to the desired location.  
Fail-safe  
When the fail-safe operation occurs, the CVT will  
not be shifted to the selected driving position.  
If the vehicle is driven under extreme conditions,  
such as excessive wheel spinning and subse-  
5-20 Starting and driving  
Downloaded from manuals search engine  
STOP/START SYSTEM  
(where fitted)  
NISSAN GREEN PROGRAM  
*The Stop/Start System will  
automatically stop the engine when all  
the following conditions are valid:  
**When the Stop/Start System symbol  
(1) is displayed the engine starts running  
automatically under at least one of the  
following conditions:  
The Stop/Start System is designed to prevent un-  
necessary fuel consumption, exhaust emissions,  
and noise during a journey:  
–
–
–
The gearshift lever is in Neutral position.  
When the vehicle comes to rest the engine is  
automatically stopped*.  
•
–
The clutch pedal is depressed.  
The clutch pedal is fully released.  
–
The brake pedal is repeatedly pressed (to main-  
tain vehicle braking performance).  
The vehicle speed is below about 2 km/h (1  
MPH).  
The engine is then automatically restarted before  
you are ready to drive away**.  
•
–
The battery voltage becomes low (due to electri-  
cal load from other vehicle systems like head-  
lights, heaters, etc., or auxiliary devices con-  
nected to the 12 volt socket inside the vehicle).  
–
–
The driver’s seat belt is buckled.  
The driver’s door is closed.  
CAUTION  
At the end of the journey the engine must be  
stopped and ignition turned OFF. Lock the ve-  
hicle as normal. Turning the ignition OFF will shut  
down all electrical systems. Failure to do this may  
result in a flat battery.  
NOTE  
–
–
The front and/or rear screen defogger is turned  
on.  
The following conditions must also be satisfied  
before the engine is automatically stopped. If the  
engine does not stop this does not indicate a  
fault with the system:  
The vehicle speed is above about 2 km/h (1  
MPH).  
NORMAL OPERATION  
–
–
–
–
The outside air temperature is above about  
5ºC.  
NOTE  
The following conditions will prevent the Stop/  
Start System automatically restarting the engine.  
Starting the engine by turning the ignition switch  
is then necessary:  
The engine coolant temperature is at normal  
operating levels.  
The vehicle has driven some distance since  
engine start.  
–
The driver’s seat belt is unbuckled, or driver’s  
door is open.  
The battery voltage and temperature are  
within normal levels.  
–
The bonnet is open.  
NIC1640  
–
–
–
The vehicle bonnet is closed.  
The Stop/Start System is always engaged at the  
start of a journey (once the engine has been started).  
The engine is automatically stopped and restarted  
during the journey if conditions are suitable  
The steering wheel is not being turned.  
The Stop/Start System has stopped the engine and  
will automatically restart the engine. The Stop/Start  
symbol j1 is shown in the vehicle information dis-  
play.  
The front and/or rear screen defoggers are  
turned OFF.  
Starting and driving 5-21  
Downloaded from manuals search engine  
When the engine is stopped the following informa-  
tion is displayed for a few seconds.  
•
•
Push and hold  
the steering  
wheel ji button  
to reset the  
[CO2 Saved]  
value.  
The display can  
be switched  
between Stop/  
Start System  
information and  
drive computer  
information by a  
short press of  
the steering  
The message can  
only be cleared by  
turning the ignition  
OFF (or restarting  
the engine).  
See “Vehicle information display” in the “2. Instru-  
ments and controls” section for information about  
the display.  
NOTE  
Automatic engine  
restart is possible  
whenever the  
m
PRECAUTIONS  
Stop/Start System  
symbol is  
The following message is displayed when there may  
be something wrong with the Stop/Start System.  
You are advised to have the system checked by a  
NISSAN dealer or qualified workshop.  
m
illuminated at the  
bottom of the  
m
display.  
wheel ji button  
The message can  
be cleared by  
Whilst the engine remains stopped the vehicle infor-  
mation display shows the accumulated quantity (es-  
timate) of carbon dioxide exhaust emissions pre-  
vented by the Stop/Start System.  
When automatic restart is not possible the following  
information is displayed. The engine must be started  
by turning the ignition switch.  
pressing the steer-  
ing wheel ji button  
NOTE  
The Stop/Start  
The message can  
be cleared by  
System symbol at  
the bottom of the  
display flashes  
pressing the steer-  
ing wheel ji but-  
ton, restarting the  
engine, or turning  
the ignition OFF.  
m
whilst the fault  
condition remains.  
m
The following information is displayed and a buzzer  
sounded to remind the driver to turn the ignition  
OFF to avoid a flat battery  
5-22 Starting and driving  
Downloaded from manuals search engine  
Start System cannot prevent unnecessary fuel  
consumption, exhaust emissions, or noise dur-  
ing your journey.  
STOP/START SYSTEM OFF SWITCH  
NOTE  
The following messages may be displayed for a  
few seconds in the vehicle information display  
when the Stop/Start System OFF switch is  
pressed.  
Stop/Start System  
disengaged  
Stop/Start System  
re-engaged  
NIC1642  
NIC1641  
–
[Trip Saving]  
The system can be temporarily disengaged by  
pressing the Stop/Start System OFF switch. Press-  
ing the button a second time will re-engage the  
Stop/Start System.  
Estimated CO2 exhaust emissions prevented  
since last reset.  
NOTE  
The [Trip Saving] value is the same informa-  
tion that is displayed when the engine is auto-  
matically stopped by the Stop/Start System.  
When the Stop/Start System is disengaged  
whilst the engine is running, the engine is pre-  
vented from automatically stopping.  
•
m m  
More information about the Stop/Start System can  
be checked using the [Settings] menu (see Instru-  
ments and Controls)  
When the Stop/Start System is disengaged af-  
•
ter the engine has been automatically stopped  
by the Stop/Start System, the engine will imme-  
diately restart if suitable conditions are present  
as described under NORMAL OPERATION.  
The engine will then be prevented from automati-  
cally stopping during the same journey.  
ENVIRONMENTAL SAVINGS  
The vehicle information display keeps a record of  
the CO2 savings that can be viewed via the [Set-  
tings] menu.  
Whenever the Stop/Start System is disengaged  
the indicator light on the Stop/Start System OFF  
switch illuminates. In this condition the Stop/  
•
See “Vehicle information display” in the “2. Instru-  
ments and controls” section for information about  
the display.  
NIC1643  
Starting and driving 5-23  
Downloaded from manuals search engine  
ULTRASONIC PARKING SENSOR  
(where fitted)  
FOUR-WHEEL DRIVE (4WD)  
(where fitted)  
–
[Total Saving]  
Estimated CO2 exhaust emissions pre-  
vented.  
•
Time that the engine has been stopped by  
the Stop/Start System.  
•
NOTE  
The [Total Saving] values cannot be reset  
and show accumulated Stop/Start System  
information since the vehicle was built.  
NSD300Z  
NSD297Z  
The Four Wheel Drive (4WD) system is used to  
select 2WD, AUTO, or LOCK depending on the  
driving conditions.  
Ultrasonic sensors jA , fitted in the vehicle’s rear  
bumper, measure the distance between the vehicle  
and an obstacle when reversing. When reverse gear  
is engaged a beeping sound is heard. The frequency  
of the beeps will increase the closer you come to  
the obstacle until, the sound becomes a constant  
beep when, the vehicle is approximately 30 cm (12  
in) from the obstacle.  
The Four Wheel Drive (4WD) system controls the  
coupling operation. Turn the control (located on the  
centre console) to select each mode: 2WD, AUTO  
or LOCK depending on the driving conditions.  
AUTO: Turn the 4WD mode control to the neutral  
(AUTO) position and the Four-Wheel Drive (4WD)  
NOTE  
AUTO indicator light  
illuminates.  
on the combination meter  
This system is intended as an aid to reversing,  
to be used in conjunction with your rear view  
mirror.  
•
2WD: Turn the control clockwise to the 2WD posi-  
tion.  
Make sure that the ultrasonic sensors are not  
obscured (by dirt, mud, snow, etc.).  
•
LOCK: When the control is turned anticlockwise to  
the LOCK position, it springs back to the AUTO  
position when released. The 4WD LOCK mode in-  
dicator light  
illuminates on the combination  
meter, to show LOCK mode is engaged. To disen-  
gage LOCK mode, turn the control anticlockwise  
again to the LOCK position and release. The 4WD  
LOCK mode indicator light will go out.  
5-24 Starting and driving  
Downloaded from manuals search engine  
CAUTION  
4WD MODE OPERATIONS  
Depending on the driving conditions, the 4WD  
mode may automatically change from 2WD to  
4WD even when the 2WD mode is selected.  
4WD mode  
indicator light  
4WD Mode  
Wheels driven  
Driving conditions  
Do not start the engine while in the 2WD, AUTO,  
or LOCK mode:  
(
m
,
)
Front wheels-  
The wheel drive mode is in  
2WD when driving on a normal  
road  
When on free-roller or jacking the front tyres  
with the rear tyres on the ground.  
•
2WD  
Goes off  
For driving on dry, paved roads  
When towing with the rear tyres raised from  
the ground.  
•
Distribution of torque to the  
front and rear wheels changes  
automatically, depending on  
road conditions encountered  
[ratio; 100:0 (2WD) → 50:50  
(4WD)]. This results in  
4WD SHIFT TIPS  
AUTO  
LOCK  
For driving on paved or slippery roads  
For driving on rough roads  
If the 4WD mode control is operated while cor-  
•
m
nering, accelerating or decelerating, or if the ig-  
nition is turned OFF while in the AUTO or LOCK  
position you may feel a jolt - this is normal.  
improved driving stability  
Four wheels*1  
m
/
The oil temperature of power train parts will in-  
•
crease if the vehicle is continuously operated  
under conditions where the difference in rotation  
between the front and rear wheels is large (wheel  
slip), such as when driving the vehicle on rough  
roads through sand or mud, or when freeing a  
stuck vehicle. In these cases, the 4WD warning  
light blinks rapidly, and the 4WD mode changes  
to the 2WD condition to protect the power train  
parts. If you stop the vehicle, with the engine  
idling, and wait until the warning light stops blink-  
ing the 4WD mode returns to the AUTO mode.  
*1  
LOCK mode changes to AUTO mode automatically when the vehicle is sharply accelerated or when the vehicle speed  
is over approximately 40 km/h (25 MPH). The 4WD LOCK indicator light goes off. Turning off the ignition automatically  
cancels LOCK mode.  
Braking distance in 4WD mode is the same as in  
2WD mode.  
•
Starting and driving 5-25  
Downloaded from manuals search engine  
Even if the mode automatically changes to AUTO  
mode, when driving in the LOCK mode, the indi-  
cator light stays in the LOCK mode.  
per second). Stop the vehicle in a safe place  
with the engine idling. If, after a while, the light  
goes out you can continue driving.  
•
4WD WARNING LIGHT  
Warning light  
Indication  
CAUTION  
Where the difference in rotation between the  
front and rear wheels is large (wheel slip) - such  
as when driving on rough roads through sand,  
mud, or freeing a stuck vehicle - the warning  
light will blink slowly (approximately once per two  
seconds). Set the 4WD mode to 2WD and do  
not drive fast. A large difference in diameters  
between the front and rear wheels will also cause  
the 4WD warning light to blink slowly. Check  
that all the tyre sizes are the same, the tyre pres-  
sures are correct, and that the tyres are not worn.  
•
There is a malfunction in the Four-  
Wheel Drive (4WD) system.  
Only use the 4WD mode control when driving  
in a straight direction (to select 2WD, AUTO or  
LOCK).  
•
Comes on  
Do not use the 4WD mode control when turn-  
ing or reversing.  
•
•
The power train oil temperature is  
abnormally high.  
Do not use the 4WD mode control with the  
front wheels spinning (to select 2WD, AUTO,  
or LOCK).  
Blinks rapidly  
The difference in wheel rotation is  
large.  
Be especially careful when starting or driving  
on slippery surfaces with the 4WD mode set  
to AUTO.  
•
•
CAUTION  
If the warning light comes on or blinks while  
•
Blinks slowly  
driving, 4WD mode will change to 2WD mode.  
Reduce the vehicle speed and have your ve-  
hicle checked by a NISSAN dealer or qualified  
workshop as soon as possible.  
Do not drive on dry, hard surfaced roads in  
the LOCK position.  
The 4WD warning light is located in the tachometer.  
The 4WD warning light comes on when the ignition  
switch is turned to the ON position and turns off  
soon after the engine is started. If the 4WD warning  
light comes on, the 4WD mode indicator light will go  
out.  
Do not drive on dry, hard surfaced roads in  
the LOCK position.  
•
•
If the 4WD warning light blinks in the follow-  
ing sequence while driving, proceed as in-  
structed:  
If the 4WD system malfunctions, or the revolution or  
radius of the front and the rear wheels differ, the  
warning light will either remain illuminated or blink  
as follows:  
–
Blinks rapidly (about twice a second)  
Pull off the road at a safe place and idle the  
engine. The driving mode will change to 2WD  
to prevent the 4WD system from malfunction-  
ing. The vehicle can be driven again as soon  
as the warning light turns off.  
High temperature transfer case oil makes the  
warning light blink rapidly (approximately twice  
•
5-26 Starting and driving  
Downloaded from manuals search engine  
–
Blinks slowly (about once every 2 seconds)  
NOTE  
road vehicles can tip over sideways much more  
easily than they can forwards or backwards.  
Change the driving mode to 2WD and reduce  
the vehicle speed as soon as safely possible.  
The 4WD mode indicator light may blink while  
shifting from one drive mode to another. Once  
shifting is completed, the 4WD mode indicator  
light will come on. If the indicator light does not  
come on immediately, make sure that the area  
around the vehicle is safe and free from ob-  
stacles. Drive the vehicle straight (DO NOT ac-  
celerate, decelerate or reverse), then turn the  
4WD mode control.  
Many hills are too steep for any vehicle. If you  
drive up them, you may stall. If you drive down  
them, you may not be able to control your speed.  
If you drive across them, you may roll over.  
•
If the warning light is still on after performing  
the above operation, have the system  
checked by a NISSAN dealer or qualified  
workshop as soon as possible.  
Do not shift gears when driving on downhill  
grades as this could cause loss of control of the  
vehicle.  
•
•
•
4WD MODE INDICATOR LIGHTS  
4WD mode indicator light (LOCK):  
•
Stay alert when driving to the top of a hill. At the  
top there could be a drop-off or other hazard that  
could cause an accident.  
If the 4WD warning lights comes on, the 4WD indi-  
cator light(s) will go out.  
This light comes on when the ignition switch is  
turned to the ON position, and turns off within 1  
second. When selecting LOCK mode while the  
engine is running, this light will illuminate simul-  
taneously along with the 4WD mode indicator  
light (AUTO).  
DRIVING FOUR-WHEEL DRIVE (4WD)  
SAFELY  
If the engine of the vehicle stalls or you cannot  
make it to the top of a steep grade, never at-  
tempt to turn around. Your vehicle could tip or  
roll over. Always drive backwards and straight  
down in R (Reverse) gear.  
Your NISSAN is designed for both normal and off-  
road use. However, avoid driving in deep water or  
mud as your NISSAN is mainly designed for leisure  
use, unlike a conventional off-road vehicle.  
4WD mode indicator light (AUTO):  
•
Never drive backwards under the following con-  
ditions as this could result in loss of control:  
This light comes on when the ignition switch is  
turned to the ON position, and turns off within 1  
second. If the engine is running, this light will illu-  
minate when selecting AUTO mode.  
Remember that Two-Wheel drive (2WD) models are  
less capable than Four-Wheel Drive (4WD) models  
for rough road driving and extrication when stuck,  
for example, in deep snow or mud.  
–
with the gear lever in N (Neutral) and/or with  
the clutch depressed and using the brake  
(MT models).  
The 4WD mode indicator light is located in the  
tachometer.  
Please observe the following precautions:  
–
with the selector lever in N (Neutral) and us-  
ing only the brake (AT or CVT models).  
The light should turn off within 1 second of the  
ignition switch being turned to the ON position.  
Drive carefully when off-road and avoid danger-  
•
ous areas. Always wear seat belts to help keep  
you and your passengers in position when driv-  
ing over rough terrain.  
Heavy braking down a hill could cause your  
brakes to overheat and fade, resulting in loss of  
control and an accident. Apply the brakes lightly  
and use a low gear to control your vehicle speed.  
•
While the engine is running, the 4WD mode indi-  
cator light will display the position selected by  
the 4WD mode control.  
Do not drive across steep slopes. Instead drive  
either straight up or straight down the slope. Off-  
•
Starting and driving 5-27  
Downloaded from manuals search engine  
Unsecured cargo can be thrown around when  
driving over rough terrain. Properly secure it so  
that it will not be thrown forwards and cause  
injury to you or your passengers.  
Before operating the vehicle, ensure that the  
driver and all passengers have their seat belts  
fastened.  
Avoid parking your vehicle on steep hills. If you  
get out of the vehicle and it rolls forwards, back-  
wards or sideways, you could be injured.  
•
•
•
•
•
•
•
Avoid raising the centre of gravity by loading  
things on the roof or equipping the vehicle with  
tyres larger than specified in this manual.  
To avoid raising the centre of gravity excessively,  
do not exceed the rated capacity of the roof rack/  
gear bin (where fitted) and evenly distribute the  
load. Secure heavy loads in the luggage area as  
far forwards and as low as possible. Do not equip  
the vehicle with tyres larger than specified. This  
could cause your vehicle to rollover.  
Always drive with the floor mats in place as the  
floor may become very hot. Particular care  
should be taken if you are barefoot.  
Lower your speed when encountering strong  
crosswinds. With its higher centre of gravity your  
NISSAN is more affected by gusty side winds.  
Slower speeds ensure better vehicle control.  
Accelerating quickly, sharp steering manoeuvres  
or sudden braking may cause loss of control.  
•
•
Do not drive beyond the performance of the  
tyres, even with 4WD. Sudden acceleration,  
steering or braking may result in loss of control  
and could cause the vehicle to become stuck.  
Be sure to check the brakes immediately after  
driving in mud or water as specified in “Wet  
brakes” later in this section.  
•
•
Whenever you drive off-road through sand, mud  
or water as deep as the wheel hub, more fre-  
quent maintenance may be required. For details,  
refer to the separately provided Warranty Infor-  
mation and Maintenance Booklet.  
If at all possible, avoid sharp turning manoeuvres,  
particularly at high speeds. Your 4WD vehicle  
has a higher centre of gravity than a 2WD ve-  
hicle and can tip over more easily. The vehicle is  
not designed for cornering at the same speeds  
as conventional 2WD models any more than low  
sports cars are designed to perform satisfacto-  
rily under off-road conditions. Failure to operate  
this vehicle correctly could result in loss of con-  
trol and/or a rollover accident.  
•
Rinse the underside of the vehicle with fresh  
water after driving through mud or sand. Re-  
move any brush or sticks that are trapped.  
•
•
Install the same size of winter tyres on all four (4)  
wheels (such as studless tyres) or install snow  
chains to the front wheels when driving on slip-  
pery roads (e.g. after a snowfall) and drive care-  
fully using 4WD.  
Do not grip the inside or spokes of the steering  
wheel when driving off-road. The steering wheel  
could jerk and injure your hands. Instead, drive  
with your fingers and thumbs on the outside of  
the rim.  
•
5-28 Starting and driving  
Downloaded from manuals search engine  
CRUISE CONTROL (where fitted)  
The cruise control system allows driving at constant  
speeds without keeping your foot on the accelerator  
pedal.  
When the cruise control system is on the speed lim-  
iter cannot be operated.  
The cruise control system operation switches are  
located on the steering wheel (right side).  
WARNING  
The cruise control system ONLY maintains a  
constant vehicle speed, it does not replace  
the driver.  
•
Always observe the posted speed limits and  
do not set the speed above them.  
•
NSD375  
Do not use the cruise control system when  
•
CRUISE indicator  
Cruise control symbol  
SET indicator  
6.  
7.  
8.  
9.  
driving under the following conditions. Doing  
so could cause a loss of vehicle control and  
result in an accident.  
NSD373  
–
When it is not possible to keep the vehicle  
at a constant speed  
Set speed value  
RES (Resume) switch  
SET switch  
1.  
2.  
3.  
4.  
The cruise control system operating condition is  
shown in the vehicle information display. For details,  
see “Cruise control/Speed limiter indicator (where  
fitted)” in the “2. Instruments and controls” section.  
–
–
–
–
–
When driving in heavy traffic  
CANCEL switch  
When driving in traffic that varies speed  
When driving in windy areas  
Speed limiter main “ON/OFF” switch (For  
details, see “Speed limiter” later in this sec-  
tion)  
PRECAUTIONS ON CRUISE  
CONTROL  
When driving on winding or hilly roads  
When driving on slippery (rain, snow, ice,  
etc.) roads  
Cruise control main “ON/OFF” switch  
5.  
The cruise control system will be automatically  
•
cancelled when there is a malfunction. Have the  
system checked by a NISSAN dealer or quali-  
fied workshop.  
CAUTION  
On manual transmission models, do not shift into  
N (Neutral) without depressing the clutch pedal  
when the cruise control is set. Should this occur,  
depress the clutch pedal and turn the cruise con-  
trol main switch off immediately. Failure to do so  
may cause engine damage.  
To properly set the cruise control system, per-  
form the steps as described in “Cruise control  
system operations” later in this section.  
•
Starting and driving 5-29  
Downloaded from manuals search engine  
4. Take your foot off the accelerator pedal.  
The vehicle will maintain the set speed.  
2 km/h or 1 MPH for M9R diesel models  
CRUISE CONTROL SYSTEM  
OPERATIONS  
Push and hold the RES (resume) j1 switch up-  
wards or the SET switch j2 downwards. The  
vehicle speed will increase or decrease to the  
new set speed.  
•
The cruise control system can be set at the follow-  
ing speeds:  
If the vehicle speed is less than the minimum set  
speed (see table), it will not be possible to set  
the cruise control system.  
Minimum  
speed  
Engine type  
Maximum speed  
The new set speed value j9 will be displayed in the  
combination meter.  
Changing a cruising speed  
1.6 petrol  
HR16DE  
MT: 170 km/h (100 MPH)  
CVT: 155 km/h (95 MPH)  
Use any one of the following methods to change the  
cruising speed.  
45 km/h  
Passing another vehicle  
(30 MPH)  
2.0 petrol  
MR20DE  
MT: 185 km/h (110 MPH)  
CVT: 175 km/h (105 MPH)  
Depress the accelerator pedal to accelerate. After  
releasing the accelerator pedal, the vehicle will re-  
turn to the previously set speed.  
Slow the vehicle as normal using the footbrake  
pedal, the SET indicator j8 in the combination  
•
1.5 diesel  
K9K  
30 km/h  
(20 MPH)  
166 km/h (70 MPH)  
170 km/h (106 MPH)  
190 km/h (119 MPH)  
meter will be turned off.  
2.0 diesel  
M9R  
30 km/h  
(18 MPH)  
The set speed value j9 will flash until the vehicle  
returns to the previously set speed.  
When the vehicle reaches the desired cruising  
speed, push and release the SET switch j2  
downwards.  
1.6 diesel  
R9M  
40 km/h  
(25 MPH)  
Cancelling the cruise control system  
The new set speed value j9 and SET indicator  
j8 will be displayed in the combination meter.  
To cancel a set speed limit, push the CANCEL  
switch j3 . The SET indicator j8 in the combination  
meter will be turned off.  
Turning the cruise control system on  
The cruise control system can be switched on after  
engine start or when driving.  
Press the accelerator pedal.  
•
The set speed value j9 will remain displayed, as  
this speed is now stored in the cruise control sys-  
tem memory.  
When the vehicle reaches the desired cruising  
speed, push and release the SET switch j2  
downwards.  
Push the cruise control main switch j5 . The  
CRUISE indicator and the cruise control symbol j7  
will illuminate in the combination meter display.  
The cruise control system will also be cancelled  
automatically by any of the following:  
The new set speed value j9 and SET indicator  
j8 will be displayed in the combination meter.  
Setting a cruising speed  
Pressing the footbrake pedal.  
•
•
•
1. Accelerate to the desired cruising speed.  
Push and release the RES (resume) j1 switch  
upwards or the SET switch j2 downwards to  
increase or decrease the set speed in steps of:  
•
Pressing the clutch pedal.  
2. Push the SET switch j2 downwards and release  
it.  
Moving the gear lever (MT models) or selector  
lever (AT or CVT models) to the N (Neutral) posi-  
tion.  
1 km/h or 1 MPH for petrol models or R9M die-  
sel models  
3. The SET indicator j8 and the set speed value  
j9 will be displayed in the combination meter  
display.  
2 km/h or 2–3 MPH K9K diesel models  
5-30 Starting and driving  
Downloaded from manuals search engine  
SPEED LIMITER  
If the vehicle slows down more than approxi-  
mately 12 km/h (8 MPH) below the set speed.  
The speed limiter allows you to set the desired ve-  
hicle speed limit. While the speed limiter is acti-  
vated, you can perform normal braking and accel-  
eration, but the vehicle will not exceed the set speed.  
•
Resuming a previous cruising speed  
If the cruising speed has been cancelled, the set  
speed value j9 will remain displayed in the combi-  
nation meter and the speed will be stored in the  
cruise control system memory. This cruising speed  
can be reactivated by pressing the RES (Resume)  
switch j1 upwards.  
When the vehicle reaches the set speed limit or if  
the set speed limit is lower than the actual vehicle  
speed, the accelerator pedal will not work until the  
vehicle speed drops below the set speed limit.  
NSD373  
WARNING  
If the vehicle speed is less than the minimum set  
speed (see table), it will not be possible to re-  
sume to the cruising speed.  
The speed limiter will not automatically brake  
the vehicle to the set speed limit.  
•
RES + (Resume) switch  
SET – (Set) switch  
1.  
2.  
3.  
4.  
5.  
Always observe posted speed limits. Do not  
set the speed above them.  
•
Turn the cruise control system off  
CANCEL switch  
The cruise control system will be turned off when  
one of the following operations is performed:  
Always confirm the setting status of the speed  
limiter in the combination meter display.  
•
Speed limiter main “ON/OFF” switch  
Cruise control main “ON/OFF” switch (For  
details, see “Cruise control (where fitted)”  
earlier in this section)  
Push the cruise control main “ON/OFF” switch  
•
When the speed limiter is set, avoid hard ac-  
•
j5 . The cruise control symbol j7 , the CRUISE  
indicator j6 , the SET indicator j8 , and the set  
speed value j9 will turn off in the combination  
meter display  
celeration to reach the set limit to ensure that  
the system can limit the speed of the vehicle  
correctly.  
The speed limiter operation switches are located on  
the steering wheel (right hand side)  
When additional floor mats are used, be sure  
•
Push the speed limiter main “ON/OFF” switch  
•
that they are correctly secured and that they  
cannot interfere with the accelerator pedal.  
Mats not adapted to the vehicle may prevent  
proper operation of the speed limiter.  
j5 . The cruise control system information in the  
combination meter will be replaced with the  
speed limiter information. For details see “Speed  
limiter” later in this section.  
When the speed limiter is on the cruise control sys-  
tem cannot be operated.  
When the vehicle is stopped and the ignition is  
turned to the off position.  
•
Turning off the cruise control system will erase  
the cruise control system memory.  
Starting and driving 5-31  
Downloaded from manuals search engine  
For 1.5 diesel (K9K) models only:  
SPEED LIMITER OPERATIONS  
The speed limiter can be set at the following speeds:  
Minimum  
When driving less than 30 km/h (20 MPH), it will not  
be possible to set the speed limit.  
Engine type  
Maximum speed  
When the speed limit is set, the SET indicator j8  
and the set speed value j9 will be displayed in the  
combination meter display.  
speed  
1.6 petrol  
HR16DE  
170 km/h (105 MPH)  
2.0 petrol  
MR20DE  
MT: 190 km/h (118 MPH)  
CVT: 170 km/h (105 MPH)  
Changing a speed limit  
Use either of the following operations to change an  
active speed limit:  
1.5 diesel  
K9K  
30 km/h  
(20 MPH)  
NSD372  
184 km/h (114 MPH)  
200 km/h (125 MPH)  
190 km/h (118 MPH)  
2.0 diesel  
M9R  
For 1.6 petrol (HR16DE), 2.0 petrol (MR20DE),  
2.0 diesel (M9R) or 1.6 diesel (R9M) models:  
The speed limiter operating condition is shown in  
the vehicle information display. For details, see  
“Vehicle information display” in the “2. Instruments  
and controls” section.  
1.6 diesel  
R9M  
Push and release the RES (Resume) switch j1  
•
upwards or SET switch j2 downwards. Each  
time you do this, the set speed will increase or  
decrease by 1 km/h (1 MPH).  
Turning the speed limiter on  
LIMIT indicator  
Speed limiter symbol  
SET indicator  
6.  
7.  
8.  
9.  
The speed limiter can be switched on after engine  
start or when driving.  
Push and hold the RES (Resume) switch j1  
•
upwards or SET switch j2 downwards. The set  
speed will increase or decrease to the next mul-  
tiple of 10 km/h (10 MPH) and then in steps of  
10 km/h (10 MPH).  
Push the speed limiter main “ON/OFF” switch j4 .  
The speed limiter symbol j7 and the LIMIT indica-  
tor j6 will illuminate in the combination meter dis-  
play.  
Set speed value  
For 1.5 diesel (K9K) models only:  
Setting speed limit  
Push and release the RES (Resume) switch j1  
•
upwards or SET switch j2 downwards. Each  
time you do this, the set speed will increase or  
decrease by 2 km/h (2 MPH).  
Push the SET switch j2 (downwards)  
For 1.6 petrol (HR16DE), 2.0 petrol (MR20DE),  
2.0 diesel (M9R) or 1.6 diesel (R9M) models:  
Push and hold the RES (Resume) switch j1  
•
The speed limit will be set at the current speed.  
•
•
upwards or SET switch j2 downwards. The set  
speed will increase or decrease in steps of 4  
km/h (2-3 MPH).  
When driving less than 30 km/h (20 MPH), the  
speed limiter will be set to the minimum possible  
set speed of 30 km/h (20 MPH).  
5-32 Starting and driving  
Downloaded from manuals search engine  
PARKING  
The new set speed limit value j9 will be displayed  
in the combination meter display.  
This speed limit can be reactivated by pressing the  
RES (Resume) switch j1 upwards.  
WARNING  
Do not park the vehicle over flammable mate-  
rials, such as dry grass, waste paper, or rags.  
They may ignite and cause a fire.  
•
•
If the current vehicle speed is higher than the previ-  
ous set speed, the accelerator pedal will not work  
and the set speed value j9 will flash until the vehicle  
speed drops below the set speed limit.  
Cancelling a speed limit  
To cancel a set speed limit, push the CANCEL  
switch j3 . The SET indicator j8 in the combination  
meter will be turned off. The set speed value j9 will  
remain displayed.  
Safe parking procedures require that:  
Turning the speed limiter off  
–
–
The handbrake is applied.  
It is also possible to override the speed limiter by  
fully depressing the accelerator pedal beyond the  
resistance point.  
The speed limiter system will be turned off when  
one of the following operations is performed:  
The gear lever is placed in an appropriate  
gear for manual transmission models.  
Push the speed limiter main “ON/OFF” switch  
–
The selector lever is placed in the P (Park)  
position for automatic transmission or con-  
tinuously variable transmission models.  
•
j4 . The speed limiter symbol j7 , the LIMIT indi-  
cator j6 , the SET indicator j8 , and the set  
speed value j9 will turn off in the combination  
meter display.  
WARNING  
The vehicle may accelerate when the speed  
limiter cancels.  
•
Failure to follow the above recommenda-  
tions could cause the vehicle to move un-  
expectedly or roll away and result in an  
accident.  
Push the cruise control main “ON/OFF” switch  
When additional floor mats are used, be sure  
that they are correctly secured and that they  
cannot interfere with the accelerator pedal.  
Mats not adapted to the vehicle may prevent  
proper operation of the speed limiter.  
•
•
j5 . The speed limiter information in the combi-  
nation meter will be replaced with the cruise con-  
trol information. For details see “Cruise control  
(where fitted)” earlier in this section.  
Never leave the engine running while the ve-  
hicle is unattended.  
•
•
Do not leave children or adults who would  
normally require the support of others alone  
in your vehicle. Pets should also not be left  
alone either. On hot, sunny days, tempera-  
tures in a closed vehicle could quickly be-  
come high enough to cause severe or possi-  
bly fatal injuries to people or animals.  
When the vehicle is stopped and the ignition is  
turned to the off position.  
Fully depress the accelerator pedal beyond the re-  
sistance point. The speed limiter will be suspended  
to allow driving above the set speed. The set speed  
value j9 will flash. The speed limiter will automati-  
cally resume when the vehicle speed drops below  
the set speed limit.  
•
Turning off the speed limiter will erase the set  
speed limit memory.  
Speed limiter malfunction  
If the speed limiter malfunctions, the set indicator  
j8 in the combination meter display will flash.  
Resuming a previous set speed  
Manual transmission models:  
•
If a set speed limit has been cancelled, the set speed  
value j9 will remain displayed in the combination  
meter and the speed will be stored in the speed lim-  
iter memory.  
Depress the clutch pedal and place the gear  
lever in the R (Reverse) position. When parking  
on an uphill gradient, place the gear lever in the  
1st (Low gear) position.  
Turn the speed limiter off by pushing the speed lim-  
iter main “ON/OFF” switch j4 and have the system  
checked by a NISSAN dealer or qualified workshop.  
Starting and driving 5-33  
Downloaded from manuals search engine  
Automatic transmission or Continuously vari-  
able transmission models:  
•
Fully depress the brake pedal and move the se-  
lector lever to the P (Park) position.  
WARNING  
Make sure that the selector lever has been  
pushed as far forward as it can go and cannot be  
moved without depressing the button on the se-  
lector lever handle.  
NSD338  
NSD339  
LHD models  
RHD models  
5-34 Starting and driving  
Downloaded from manuals search engine  
TRAILER TOWING  
When parked on a sloping driveway, turn the  
wheels so the vehicle will not roll into the street  
in case it moves.  
Your new vehicle was designed to be used primarily  
to carry passengers and luggage.  
Contact a NISSAN dealer or qualified workshop  
for more information on this matter.  
•
•
Remember that towing a trailer will place additional  
loads on your vehicle’s engine, drive-train, steering,  
braking and other systems. Towing a trailer will also  
exaggerate other conditions, such as sway caused  
by crosswinds, rough road surfaces or passing  
trucks. Driving style and speed must be adjusted  
according to the circumstances. Before towing a  
trailer, see a NISSAN dealer or qualified workshop  
for an explanation of towing equipment and its  
proper use.  
The trailer must be loaded so that heavy goods  
are distributed over the axle and as low in the  
trailer as possible. Poor load distribution can se-  
riously affect the stability of the trailer and tow  
vehicle.  
•
FACING DOWNHILL: j1  
Turn the wheels into the kerb, allow the vehicle  
to move forward until the kerb side wheel gently  
touches the kerb. Then set the handbrake.  
Do not exceed the maximum permitted vertical  
load on the trailer hitch.  
•
•
•
FACING UPHILL: j2  
•
•
Turn the wheels away from the kerb and allow  
the vehicle to move back until the kerb side wheel  
gently touches the kerb. Then set the handbrake.  
Before driving, make sure that the lighting sys-  
tem of the trailer works properly.  
When towing with 4WD models, the 4WD mode  
switch should be in the AUTO position. Using  
the vehicle in AUTO mode gives better traction,  
particularly when moving off from stationary and/  
or on an incline, as the vehicle is less likely to  
wheel spin.  
OPERATING PRECAUTIONS  
NO KERB — FACING DOWNHILL OR UPHILL:  
j3  
Avoid towing a trailer during the running-in  
schedule.  
•
Turn the wheels toward the side of the road so  
the vehicle will move away from the centre of the  
road if it moves. Then set the handbrake.  
Choose proper coupling devices (trailer hitch,  
•
safety chain, roof carrier, etc.) for your vehicle  
and trailer. These devices are available from a  
NISSAN dealer or qualified workshop where you  
can also obtain more detailed information about  
trailer towing.  
Turn the ignition switch to the LOCK position  
and remove the key/Intelligent Key (where fit-  
ted).  
Avoid abrupt starts, accelerations and stops.  
Avoid sharp turns and lane changes.  
•
•
•
•
•
•
Always drive your vehicle at a moderate speed.  
Always turn off ignition after parking a vehicle  
with Stop/Start System fitted to avoid a possible  
flat battery.  
Heavy-duty kits are available at a NISSAN dealer  
or qualified workshop.  
Always block the wheels on both vehicle and  
trailer when parking. Apply the handbrake (where  
fitted) on the trailer. Parking on a steep slope is  
not recommended.  
It is advisable to contact a NISSAN dealer or  
•
NOTE  
qualified workshop for towing details, before  
towing a trailer up steep slopes for long dis-  
tances.  
The Stop/Start System is designed to prevent  
unnecessary fuel consumption, exhaust emis-  
sions and noise during a journey. The Stop/  
Start System does not automatically turn off  
ignition at the end of a journey.  
If parking on a steep slope is unavoidable it is  
also advisable to put the vehicle into gear, or  
select P (Park (AT or CVT models), and turn the  
front wheels into the kerb (in addition to the other  
precautions described). Before parking on a  
Never allow the total trailer load (trailer weight  
plus its cargo weight) to exceed the maximum  
set for the coupling device.  
•
Starting and driving 5-35  
Downloaded from manuals search engine  
steep slope consider the incline (the towing  
weights quoted are for a 12% slope).  
Follow all of the coupling device manufacturer’s in-  
structions for installation and use.  
SAFETY CHAINS  
Always use a suitable chain between the vehicle  
and trailer. The chain should be attached to the hitch  
and not to the vehicle bumper or axle. Be sure to  
leave enough slack in the chain to permit turning  
corners. The chain should not drag on the ground:  
passing the chain across the trailer hitch may be the  
best practice depending on your trailer.  
Follow the trailer manufacturer’s instructions.  
•
•
Have your vehicle serviced more often than at  
the intervals specified in the separately provided  
Warranty Information and Maintenance booklet.  
Trailer towing requires more fuel than under nor-  
mal circumstances because of a considerable  
increase in traction power required and resis-  
tance.  
•
•
TRAILER BRAKES  
Ensure that trailer brakes are installed as required  
by local regulations. Also check that all other trailer  
equipment conforms to local regulations.  
When towing a trailer, observe the following re-  
stricted towing speed:  
Speed: below 100 km/h (62 MPH)  
TRAILER DETECTION (where fitted)  
CAUTION  
When towing a trailer and the turn signal switch is  
used, the electrical system of the vehicle will detect  
an additional electrical load of the trailer lighting. As  
a result, the trailer direction indicator light comes  
on.  
While towing a trailer, check the engine coolant  
temperature gauge regularly to prevent engine  
overheating.  
TYRE PRESSURE  
INSTALLATION OF COUPLING  
DEVICE  
When towing a trailer, inflate the vehicle tyres to the  
maximum recommended COLD tyre pressure, as  
indicated on the tyre placard (for full loading). Make  
sure the trailer tyre pressures are correct.  
NISSAN recommends that the coupling device for  
trailer towing be installed under the following condi-  
tions:  
CAUTION  
Maximum permissible vertical load on the cou-  
pling device: 736 N (75 kg, 165 lb)  
•
Do not tow a trailer when the vehicle is installed  
with a temporary-use spare tyre.  
The coupling device, mounting points and instal-  
lation parts on your vehicle: as shown as an ex-  
ample in the illustration.  
•
5-36 Starting and driving  
Downloaded from manuals search engine  
NSD348  
5–seater  
7–seater  
Rear overhang of coupling device:  
jI  
jII  
5–seater  
7–seater  
925 mm (36.4 in)  
977 mm (38.5 in)  
jA  
Starting and driving 5-37  
Downloaded from manuals search engine  
VEHICLE SECURITY  
POWER STEERING SYSTEM  
When leaving your vehicle unoccupied:  
overheating. No servicing is required. The EPAS  
system will return to normal operation the next time  
the vehicle is driven.  
WARNING  
Always remove the ignition key or Intelligent Key  
(where fitted) and take it with you – even in your  
own garage.  
•
If the Electrically Power Assisted Steering  
•
warning light (EPAS) illuminates while driv-  
ing, the power assist for steering will be dis-  
abled. Greater steering efforts are required to  
operate the steering wheel, especially in  
sharp turns and at low speed. Stop the ve-  
hicle as soon as safely possible and contact a  
NISSAN dealer or qualified workshop for fur-  
ther assistance.  
Similarly, the EPAS system may not provide full as-  
sistance during periods of reduced battery voltage  
but will recover once normal battery voltage is re-  
stored.  
Close all windows completely and lock all doors.  
•
•
Always park your vehicle where it can be seen.  
At night, park in a well lit area.  
If the EPAS warning light comes on while the engine  
is running, it may indicate that the EPAS system is  
not working properly. As result greater steering ef-  
forts are required to steer the steering wheel, espe-  
cially in sharp turns and at low speeds. Have the  
system checked by a NISSAN dealer or qualified  
workshop as soon as possible.  
If the vehicle is equipped with an alarm or immo-  
bilization device, use it – even for short periods.  
•
Do not leave children and pets in the vehicle  
unattended.  
•
In certain circumstances, factors external to  
•
the EPAS system may contribute to the illumi-  
nation of the warning light. If the warning light  
illuminates, stop the vehicle as soon as safely  
possible if driving. Turn the ignition switch to  
the “OFF” position and wait for approximately  
20 seconds, then turn the ignition switch to  
the ON position again. If the light remains illu-  
minated, we recommend you to contact a  
NISSAN dealer or qualified workshop. See  
“Warning/indicator lights and audible  
reminders” in the “2. Instruments and  
controls” section for further details regarding  
the EPAS warning light.  
Do not leave valuables on view to tempt a thief.  
•
Always take your valuables with you. If you must  
leave something in your vehicle, lock it in the lug-  
gage compartment or hide it out of sight.  
NOTE  
Incorrectly inflated tyres can lead to poor steer-  
ing ability and make the driver suspect a steering  
problem: keep the vehicle’s tyres inflated to the  
correct pressure at all times.  
Do not leave the vehicle documents in your ve-  
•
hicle. In the unfortunate event of your vehicle  
being stolen, the documents will only help a thief  
to sell the vehicle.  
CAUTION  
Do not leave articles on a roof rack as they are  
particularly vulnerable. If possible, remove them  
from the rack and lock them inside the vehicle.  
•
Any malfunction or accident that could have dam-  
aged the steering components (including actual  
or attempted theft damage) should be reported  
to a NISSAN dealer or qualified workshop.  
The EPAS (Electrically Power Assisted Steering)  
system is designed to assist steering.  
Do not leave the spare key or Intelligent Key in  
the vehicle – keep it in a safe place at home.  
•
The steering may appear to feel slightly stiff follow-  
ing parking manoeuvres including a great deal of  
steering. This is not a malfunction; it is caused by a  
control system designed to prevent the motor from  
Do not leave a note of your vehicle’s key number  
•
in the vehicle. A thief may break into the vehicle,  
note the key number and return with a new key  
and drive the vehicle.  
5-38 Starting and driving  
Downloaded from manuals search engine  
BRAKE SYSTEM  
The brake system has two separate hydraulic cir-  
cuits. If one circuit malfunctions, you will still have  
braking ability with two wheels.  
hill gradient. Overheated brakes may reduce brak-  
ing performance and could result in loss of vehicle  
control.  
ANTI-LOCK BRAKING SYSTEM (ABS)  
WARNING  
CAUTION  
BRAKE PRECAUTIONS  
Vacuum assisted brake  
The Anti-lock Braking System (ABS) is a so-  
•
phisticated device, but it cannot prevent acci-  
dents resulting from careless or dangerous  
driving techniques. It can help maintain ve-  
hicle control during braking on slippery sur-  
faces. Remember that stopping distances  
may also be longer on rough, gravel or snow  
covered roads, or if you are using snow  
chains. Always maintain a safe distance from  
the vehicle in front of you. Ultimately, the  
driver is responsible for safety.  
While driving on a slippery surface, be careful  
when braking, accelerating or downshifting.  
Abrupt braking actions or sudden acceleration  
could cause the wheels to skid and result in an  
accident.  
The brake booster aids braking by using engine  
vacuum. If the engine stops or the drive belt is bro-  
ken, you can stop the vehicle by depressing the  
brake pedal. However, greater foot pressure on the  
brake pedal will be required to stop the vehicle and  
the stopping distance will be longer.  
Be aware that brakes will fade if repeated heavy  
brake applications are made.  
Driving uphill  
Wet brakes  
When starting on a steep gradient, it is sometimes  
difficult to operate the brake (AT or CVT models) or  
both the brake and clutch (MT models). Use the  
handbrake to hold the vehicle. Do not slip the clutch  
(MT models). When ready to start, slowly release  
the handbrake while depressing the accelerator  
pedal and releasing the clutch (MT models) or de-  
pressing the accelerator pedal (AT or CVT models).  
When the vehicle is washed or driven through wa-  
ter, the brakes may get wet. As a result, your brak-  
ing distance will be longer and the vehicle may pull  
to one side during braking.  
Tyre type and condition may also affect brak-  
ing effectiveness.  
•
–
When replacing tyres, install the specified  
size of tyres on all four wheels.  
To dry brakes, drive the vehicle at a safe speed  
while lightly pressing the brake pedal to heat up the  
brakes. Do this until the brakes return to normal.  
Avoid driving the vehicle at high speeds until the  
brakes function correctly.  
–
When installing a spare tyre, make sure it  
is the proper size and type as specified on  
the  
tyre  
placard.  
See  
“Vehicle  
Driving downhill  
identification” in the “9. Technical  
information” section for the tyre placard  
location.  
The engine braking action is effective for controlling  
the vehicle while descending hills.  
Using the brakes  
Avoid resting your foot on the brake pedal while  
driving. This will overheat the brakes, wear out the  
brake linings and pads faster and reduce fuel  
economy performance.  
–
For detailed information, see “Wheels and  
tyres” in the “8. Maintenance and  
do-it-yourself” section.  
The gear lever (MT models) should be placed in a  
gear position low enough to obtain sufficient engine  
braking.  
The Anti-lock Braking System (ABS) controls the  
brakes so that the wheels do not lock during hard  
braking or when braking on slippery surfaces. The  
system detects the rotation speed at each wheel  
For the AT or CVT models, a low gear position in  
the manual shift mode, low enough to obtain suffi-  
cient engine braking, should be selected.  
To help reduce brake wear and to prevent the brakes  
from overheating, reduce speed and downshift to a  
lower gear before going down a slope or long down-  
Starting and driving 5-39  
Downloaded from manuals search engine  
ELECTRONIC STABILITY  
PROGRAMME (ESP) SYSTEM  
(where fitted)  
and varies the brake fluid pressure to prevent each  
wheel from locking and sliding. By preventing each  
wheel from locking, the system helps the driver to  
maintain steering control and helps to minimise  
swerving and spinning on slippery surfaces.  
When accelerating, driving on slippery surfaces or  
suddenly avoiding obstacles on roads, the vehicle  
might swerve or slip. The Electronic Stability Pro-  
gramme (ESP) system continuously monitors and  
compares the driver’s intended speed and the travel  
direction. The system adjusts wheel brake pressure  
and engine torque to assist in improving vehicle sta-  
bility.  
Normal operation  
The ABS will not initiate at speeds below 5 to 10  
km/h (3 to 6 MPH). The speeds will vary according  
to road conditions.  
When the ABS senses that one or more wheels are  
close to locking up, the actuator rapidly applies and  
releases hydraulic pressure. This action is similar to  
pumping the brakes very quickly. You may feel a  
pulsation in the brake pedal and hear a noise from  
the actuator under the bonnet when it is operating.  
This is normal and indicates that the ABS is working  
properly. However, the pulsation may indicate that  
road conditions are hazardous and extra care is re-  
quired while driving.  
Using the system  
Depress the brake pedal and hold it down. Depress  
the brake pedal with firm steady pressure, but do  
not pump the brakes. The ABS will operate to pre-  
vent the wheels from locking up. Steer the vehicle to  
avoid obstacles.  
When the ESP system is operating, the “SLIP”  
•
indicator light (  
blinks.  
) in the combination meter  
When only the traction control (TCS) system in  
the ESP system is operating, the “SLIP” indica-  
•
•
WARNING  
tor light (  
blink.  
) in the combination meter will also  
Do not pump the brake pedal. Doing so may in-  
crease the stopping distance.  
If the “SLIP” indicator light (  
) blinks, the  
Self-test feature  
road conditions are slippery. Be sure to drive  
carefully. See “Warning/indicator lights and au-  
dible reminders” in the “2. Instruments and  
controls” section.  
The ABS includes electronic sensors, electric  
pumps, hydraulic solenoids and a computer. The  
computer has a built-in diagnostic feature that tests  
the system each time you start the engine and move  
the vehicle at a low speed in forward or reverse.  
When the self-test occurs, you may hear a “clunk”  
noise and/or feel a pulsation in the brake pedal. This  
is normal and does not indicate a malfunction. If the  
computer senses a malfunction, it switches the ABS  
off and illuminates the ABS warning light on the  
instrument panel. The brake system then operates  
normally, but without anti-lock assistance.  
Indicator light  
•
If a malfunction occurs in the system, the “SLIP”  
indicator light (  
) and the ESP indicator light  
(
) come on in the combination meter.  
As long as these indicator lights are on, the trac-  
tion control function is cancelled.  
The ESP system uses Active Brake Limited Slip  
(ABLS) system to improve vehicle traction. The Ac-  
tive Brake Limited Slip (ABLS) system works when  
one of the driving wheels is spinning on a slippery  
If the ABS warning light illuminates during the self-  
test or while driving, have the vehicle checked by a  
NISSAN dealer or qualified workshop.  
5-40 Starting and driving  
Downloaded from manuals search engine  
surface. The Active Brake Limited Slip (ABLS) sys-  
tem, brakes the spinning wheel to distribute the driv-  
ing power to the other driving wheel.  
If engine related parts, such as a muffler, are  
not standard equipment or are extremely de-  
OFF indicator light (  
indicator light (  
) and/or the “SLIP”  
) may illuminate.  
•
•
teriorated, the ESP OFF indicator light (  
and/or the “SLIP” indicator light (  
illuminate.  
)
) may  
The ESP system is not a substitute for winter  
tyres or snow chains on a snow covered road.  
•
If the vehicle is operated with the ESP system turned  
off, all ESP and TCS functions will be turned off.  
The Active Brake Limited Slip (ABLS) system and  
ABS will still operate with the ESP system off. If the  
Active Brake Limited Slip (ABLS) system or the ABS  
NOTE  
If brake related parts, such as brake pads,  
rotors and callipers, are not standard equip-  
ment or are extremely deteriorated, the ESP  
system may not operate properly and the ESP  
The ESP system should be switched on under  
•
normal circumstances although it may be ad-  
vantageous to switch off the ESP system to  
allow wheelspin under the following condi-  
tions:  
is activated, the “SLIP” indicator light (  
) will  
blink and you may hear a clunk noise and/or feel a  
pulsation in the brake pedal. This is normal and does  
not indicate a malfunction.  
OFF indicator light ( ) and/or the “SLIP”  
indicator light ( ) may illuminate.  
Do not modify the vehicle’s suspension. If  
suspension parts, such as shock absorbers,  
struts, springs, stabiliser bars and bushings,  
are not NISSAN-approved or are extremely  
deteriorated, the ESP system may not oper-  
ate properly. This could adversely affect ve-  
hicle handling performance and the ESP OFF  
–
–
When driving in deep snow or mud.  
•
•
•
While the ESP system is operating, you may feel a  
pulsation in the brake pedal and hear a noise or  
vibration from under the bonnet. This is normal and  
indicates that the ESP system is working properly.  
When trying to rock a vehicle free that is  
stuck in snow.  
–
When driving with snow chains.  
The ESP computer has a built in diagnostic feature  
that tests the system each time the engine is started  
and the vehicle moves forwards or reverses at a  
slow speed. When the self-test occurs, you may  
hear a clunk noise and/or feel a pulsation in the  
brake pedal. This is normal and is not an indication  
of a malfunction.  
If the ESP system has been switched off, drive  
carefully with reduced speed. When road con-  
ditions allow, ESP should be switched back  
on.  
•
indicator light (  
cator light (  
) and/or the “SLIP” indi-  
) may illuminate.  
When driving on extremely inclined surfaces,  
such as higher banked corners, the ESP sys-  
tem may not operate properly and the ESP  
OFF indicator light (  
indicator light (  
) and/or the “SLIP”  
) may illuminate. Do not  
WARNING  
drive on these types of roads. If ESP OFF indi-  
cator light does illuminate after driving  
The ESP system is designed to help improve  
•
driving stability but does not prevent accidents  
caused by abrupt steering operation at high  
speeds, or careless or dangerous driving  
techniques. Reduce vehicle speed and be es-  
pecially careful when driving and cornering on  
slippery surfaces. Always drive carefully.  
on extreme surfaces, restart the engine to re-  
set the ESP system.  
If wheels or tyres other than the  
recommended ones are used, the ESP sys-  
tem may not operate properly and the ESP  
Starting and driving 5-41  
Downloaded from manuals search engine  
COLD WEATHER DRIVING  
NOTE  
ELECTRONIC STABILITY  
PROGRAMME (ESP) OFF SWITCH  
WARNING  
The ESP system cannot be switched off when  
the ESP system is operating and the “SLIP” indi-  
Whatever the conditions, drive with caution.  
•
Accelerate and decelerate with great care. If  
accelerating or decelerating too fast, the drive  
wheels will lose even more traction.  
cator light (  
) is blinking.  
Push the ESP OFF switch again, or restart the en-  
gine, to turn the system ON. See “Electronic Stabil-  
ity Programme (ESP) system (where fitted)” earlier  
in this section for operational details.  
Allow more stopping distance in cold weather  
driving. Braking should be started sooner than  
on dry surfaces.  
•
Keep at a greater distance from the vehicle in  
front of you on slippery roads.  
•
NSD374  
Wet ice (0°C, 32°F and freezing rain), very cold  
•
snow and ice can be slick and very difficult to  
drive on. The vehicle will have a lot less trac-  
tion or grip under these conditions. Try to  
avoid driving on wet ice until the road is salted  
or sanded.  
LHD models  
RHD models  
jA  
jB  
The vehicle should be driven with the Electronic  
Stability Programme (ESP) system “ON” for most  
driving conditions.  
Watch for slippery spots (black ice). These  
•
may appear on an otherwise clear road in  
shaded areas. If a patch of ice is seen ahead,  
brake before driving on it. Try not to brake  
while actually on the ice and avoid any sud-  
den steering manoeuvres.  
When the vehicle get stuck in mud or snow, the  
ESP system reduces the engine output to decrease  
wheel spin. The engine speed will be reduced even  
if the accelerator is depressed to the floor. If maxi-  
mum engine power is needed to free a stuck ve-  
hicle, turn the ESP system off.  
Do not use cruise control (where fitted) on  
slippery roads.  
•
To turn off the ESP system, push the ESP OFF  
Snow can trap dangerous exhaust gas under  
your vehicle. Keep snow clear of the exhaust  
pipe and from around your vehicle.  
•
switch. The ESP OFF indicator light (  
come on.  
) will  
5-42 Starting and driving  
Downloaded from manuals search engine  
CAUTION  
BATTERY  
CORROSION PROTECTION  
Skid and traction capabilities of studded snow  
tyres on wet or dry surfaces may be poorer  
than that of non-studded snow tyres.  
If the battery is not fully charged during extremely  
cold weather conditions, the battery fluid may freeze  
and damage the battery. To maintain maximum effi-  
ciency, the battery should be checked regularly. For  
details, see “Battery” in the “8. Maintenance and  
do-it-yourself” section.  
Chemicals used for road surface de-icing are ex-  
tremely corrosive and will accelerate corrosion and  
the deterioration of underbody components such as  
the exhaust system, fuel and brake lines, brake  
cables, floor pan, and wings.  
3) Snow chains may be used, if desired. But the  
use of snow chains may be prohibited in some  
areas. Therefore, check the local laws before  
installing snow chains. When installing snow  
chains, make sure they are of proper size for the  
tyres on your vehicle and are installed according  
to the snow chain manufacturer’s instructions.  
Use chain tensioners when recommended by the  
snow chain manufacturer to ensure a tight fit.  
Loose end links of the snow chain must be se-  
cured or removed to prevent the possibility of  
whipping action damage to the wings or under-  
carriage. In addition, drive at a reduced speed,  
otherwise, your vehicle may be damaged and/or  
vehicle handling and performance may be ad-  
versely affected.  
In the winter, the underbody must be cleaned  
periodically. For additional information, see “Cor-  
rosion protection” in the “7. Appearance and  
care” section.  
ENGINE COOLANT  
If the vehicle is to be left outside without anti-freeze,  
drain the cooling system. Refill before operating the  
vehicle. For details, see “Engine cooling system” in  
the “8. Maintenance and do-it-yourself” section.  
For additional protection against rust and corrosion,  
which may be required in some areas, consult a  
NISSAN dealer or qualified workshop.  
TYRE EQUIPMENT  
1) The SUMMER tyres are of a tread design to pro-  
vide superior performance on dry surfaces. How-  
ever, the performance of these tyres will be sub-  
stantially reduced in snowy and icy conditions. If  
you operate your vehicle on snowy or icy roads,  
NISSAN recommends the use of MUD & SNOW  
or ALL SEASON tyres on all four wheels. Please  
consult a NISSAN dealer or qualified workshop  
for tyre type, size, speed rating and availability  
information.  
SPECIAL WINTER EQUIPMENT  
It is recommended to carry the following items in the  
vehicle during winter:  
A scraper and stiff-bristled brush to remove ice  
and snow from the windows.  
•
2) For additional traction on icy roads, studded  
tyres may be used. However, some countries,  
provinces and states prohibit their use. Check  
applicable laws before installing studded tyres.  
A sturdy, flat board to be placed under the jack  
to give it firm support.  
•
A shovel to dig the vehicle out of snowdrifts.  
•
•
Extra windscreen washer fluid to refill the reser-  
voir tank.  
Starting and driving 5-43  
Downloaded from manuals search engine  

Related Topics

Running-in schedule Before starting the engine Precautions when starting and driving Exhaust gas (Carbon Monoxide) On-pavement and off-road driving precautions Three-way catalyst (Petrol engine models) To help prevent damage Turbocharger system (Diesel engine models) Diesel Particulate Filter (DPF) (where fitted) Regeneration restrictions If regeneration fails Care when driving Engine cold start period Loading luggage Driving on wet roads Driving under winter conditions Ignition switch Automatic transmission or Continuously variable transmission Steering lock Key positions Ignition knob (where fitted) Manual transmission Ignition knob position Emergency key ? Intelligent Key dead battery situation NISSAN Anti-Theft System (NATS) Starting the engine Driving the vehicle Driving with manual transmission Driving with automatic transmission or with continuously variable transmission (Models with manual shift) Driving with Continuously Variable Transmission (CVT) (Models without manual shift) Stop/Start System (where fitted) Normal operation Precautions Stop/Start System OFF switch Environmental savings Ultrasonic Parking Sensor (where fitted) Four-wheel Drive (4WD) (where fitted) 4WD mode operations 4WD shift tips 4WD Warning light 4WD Mode indicator lights Driving four-wheel drive (4WD) safely Cruise control (where fitted) Precautions on cruise control Cruise control system operations Speed limiter Speed limiter operations Parking Trailer towing Operating precautions Tyre pressure Safety chains Trailer brakes Trailer detection (where fitted) Installation of coupling device Vehicle security Power steering system Brake system Brake precautions Anti-lock Braking System (ABS) Electronic Stability Programme (ESP) system (where fitted) Electronic Stability Programme (ESP) OFF switch Cold weather driving Battery Engine coolant Tyre equipment Special winter equipment Corrosion protection

Popular Owner Manuals