2006-2014 Nissan Qashqai SUV Starting and driving -> Driving the vehicle User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Starting and driving -> Driving the vehicle for Your Nissan Qashqai SUV First Generation (2006-2014)

DRIVING THE VEHICLE  
mately 1/3 to the floor) and hold it then crank  
the engine. Release the ignition switch and  
the accelerator pedal when the engine starts.  
DRIVING WITH MANUAL  
TRANSMISSION  
CAUTION  
CAUTION  
Do not rest your foot on the clutch pedal while  
driving. This may cause clutch damage.  
•
Do not operate the starter for more than 15  
seconds at a time. If the engine does not start,  
turn the ignition switch to the “OFF” position  
and wait 10 seconds (Petrol engine models)  
or 20 seconds (Diesel engine models) before  
cranking again, otherwise the starter could be  
damaged.  
•
Stop your vehicle completely before shifting  
into the R (Reverse) position.  
•
When you are shifting from one gear to an-  
•
NSD340  
other, be certain to depress the clutch pedal  
all the way to the floor to avoid clashing or  
chipping the gears.  
5–speed MT  
If it becomes necessary to start the engine  
with a booster battery and jumper leads, the  
instructions and cautions contained in the  
“Jump-starting” in the “6. In case of  
emergency” section should be carefully fol-  
lowed.  
•
Avoid abrupt starts and acceleration for your  
safety.  
•
When quick acceleration is required for some  
•
reason, shift to a lower gear and accelerate  
until the vehicle reaches the maximum speed  
in each gear. Do not exceed the speed limit of  
any gear. Pay special attention when acceler-  
ating or when shifting into a lower gear on  
slippery surfaces. Sudden acceleration or  
down shifting could cause the wheels to skid  
and result in loss of control.  
7. Warm-up  
Allow the engine to idle for at least 30 seconds  
after starting. Drive at moderate speed for a short  
distance first, especially in cold weather.  
NSD292Z  
6–speed MT (where fitted)  
Shifting  
WARNING  
RHD models  
jA  
jB  
j1  
Do not leave the vehicle unattended while the  
engine is warming up.  
LHD models  
Gear lever ring  
To change gears, fully depress the clutch pedal,  
shift into the appropriate gear, then release the  
clutch slowly and smoothly.  
5-12 Starting and driving  
Downloaded from manuals search engine  
To ensure smooth gear changes, fully depress the  
clutch pedal before operating the gear lever. If the  
clutch pedal is not fully depressed before the trans-  
mission is shifted, a gear noise may be heard. This  
could result in damage to the transmission.  
However, the driver remains responsible for decid-  
ing the most suitable gear according to actual ve-  
hicle, road and traffic conditions.  
NOTE  
No arrow is displayed is some circumstances in-  
cluding:  
Start the vehicle in 1st gear and shift through the  
gears in sequence according to the vehicle speed.  
–
–
The actual gear matches recommended gear  
The vehicle speed is approx. 0 km/h  
NIC1639  
Reverse gear:  
Model with Stop/Start System  
To reverse with 5–speed manual transmission,  
•
stop the vehicle and shift the gear lever into the  
N (Neutral) position then to the R (Reverse) posi-  
tion.  
To reverse with 6–speed manual transmission,  
proceed as follows:  
•
1) Stop the vehicle.  
2) Move the gear lever into the N (Neutral) posi-  
tion.  
NIC1648  
3) Pull and hold the gear lever ring j1 up.  
Model without Stop/Start System  
4) Move the gear lever into the R (Reverse) po-  
sition.  
Gear shift indicator (where fitted):  
The gear shift indicator jA located in the lower part  
of the vehicle information display can help to im-  
prove the level of environmentally friendly driving.  
5) Release the gear lever ring and safely drive  
the vehicle backwards.  
Following the gear shift indicator by changing to a  
higher (or lower) gear whenever the UP (or DOWN)  
arrow is displayed may improve fuel economy  
The gear lever ring returns to its original posi-  
tion when the gear lever is moved to the N  
(Neutral) position.  
An UP arrow suggests shifting to a higher gear, a  
down arrow suggests shifting to a lower gear.  
When the gear lever is in the R (Reverse) position,  
either the NISSAN Connect monitor (where fitted)  
Starting and driving 5-13  
Downloaded from manuals search engine  
or the ultra sonic parking sensor (where fitted) will  
be activated. For details, see “Rear-view monitor  
(where fitted)” in the “4. Display screen, heater and  
air conditioner, and audio system” section, “Around  
view monitor (where fitted)” in the “4. Display  
screen, heater and air conditioner, and audio  
system” section or “Ultrasonic Parking Sensor  
(where fitted)” later in this section.  
selector position. If it does, have your vehicle  
checked by a NISSAN dealer or qualified  
workshop.  
Make sure that the selector lever is in the  
desired position. Use the D (Drive), or Manual  
shift mode to move forwards and the R (Re-  
verse) to move backwards. Release the hand-  
brake lever and the footbrake pedal, then de-  
press the accelerator pedal to start the vehicle  
in motion and merge with traffic (avoid abrupt  
starting and spinning the wheels).  
Do not depress the accelerator pedal while  
shifting from P (Park) or N (Neutral) to R (Re-  
verse), D (Drive) or Manual shift modes posi-  
tion. Always depress the brake pedal until  
shifting is completed.  
•
•
If it is difficult to move the gear lever into R (Re-  
verse) or 1st. Shift into N (Neutral), then release the  
clutch pedal. Fully depress the clutch pedal again  
and shift into R (Reverse) or 1st.  
Avoid revving up the engine while the vehicle  
is stopped, this could cause unexpected ve-  
hicle movement [if the selector lever is in the  
R (Reverse), D (Drive), or Manual shift mode  
position] or damage the engine [if the selec-  
tor lever is in the N (Neutral) or P (Park) posi-  
tion].  
•
On an uphill grade, do not hold the vehicle by  
depressing the accelerator pedal. The foot-  
brake should be used for this purpose, in or-  
der to hold the vehicle in place and to prevent  
overheating of the transmission.  
DRIVING WITH AUTOMATIC  
TRANSMISSION OR WITH  
CONTINUOUSLY VARIABLE  
TRANSMISSION (Models with manual  
shift)  
Shift into the N (Neutral) position and apply  
the handbrake when at a standstill for longer  
than a short waiting period.  
•
•
WARM THE ENGINE UP  
•
•
Due to the higher idle speeds when the en-  
gine is cold, extra caution must be taken when  
shifting the selector lever into the driving po-  
sition immediately after starting the engine.  
Keep the engine at idling speed while shifting  
from the N (Neutral) position to any driving  
position.  
CAUTION  
The cold engine idle speed is high, so use  
caution when shifting into a forward or re-  
verse gear before the engine has warmed up.  
•
CAUTION (when starting the vehicle):  
PARKING THE VEHICLE  
DEPRESS THE FOOTBRAKE PEDAL  
•
Depress the footbrake pedal and, once the  
vehicle stops, move the selector lever into the  
P (Park) position, pull the handbrake lever and  
release the footbrake pedal.  
Avoid revving up the engine while the vehicle  
is stopped. This could cause unexpected ve-  
hicle movement.  
When the engine is running, shifting the se-  
lector lever into the R (Reverse), D (Drive) or  
Manual shift mode position without depress-  
ing the brake pedal causes the vehicle to  
move slowly. Be sure the brake pedal is fully  
depressed and the vehicle is stopped, before  
shifting the selector lever.  
•
Driving precautions  
Never shift to P (Park) or R (Reverse) while  
Starting the vehicle  
•
1. After starting the engine, fully depress the foot-  
brake pedal before shifting the selector lever from  
P (Park) to R (Reverse), D (Drive) or Manual shift  
mode.  
the vehicle is moving, this could result in dam-  
age to the transmission.  
BE AWARE OF THE SELECTOR LEVER POSI-  
TION  
•
Start the engine in the P (Park) or N (Neutral)  
position. The engine will not start in any other  
•
5-14 Starting and driving  
Downloaded from manuals search engine  
2. Keep the footbrake pedal depressed and push  
the selector lever button to shift into a driving  
gear.  
and air conditioner, and audio system” section,  
“Around view monitor (where fitted)” in the “4. Dis-  
play screen, heater and air conditioner, and audio  
system” section or “Ultrasonic Parking Sensor  
(where fitted)” later in this section.  
Push the button while depressing the  
brake pedal.  
Push the button to shift.  
3. Release the handbrake and footbrake, then  
gradually start the vehicle in motion by pressing  
the accelerator pedal.  
Shift without depressing the brake  
pedal.  
N (Neutral):  
Neither forward nor reverse gear is engaged. The  
engine can be started in this position. You may shift  
to N and restart a stalled engine while driving the  
vehicle.  
The automatic transmission or continuously variable  
transmission is designed so that the footbrake pedal  
MUST be depressed before shifting from P (Park)  
to any drive position while the ignition switch is ON.  
Push the button to shift into P (Park) or R (Reverse).  
All other positions can be selected without pushing  
the button.  
P (Park):  
D (Drive):  
Use this position when the vehicle is parked or when  
starting the engine. Always make sure that the ve-  
hicle is completely stopped before moving the se-  
lector lever into the P (Park) position. For maximum  
safety, the footbrake pedal must be depressed be-  
fore moving the selector lever into the P (Park) posi-  
tion. Use this position together with the handbrake.  
When parking on a hill, first depress the footbrake  
pedal, apply the handbrake and then shift into the P  
(Park) position.  
Use this position for all normal forward driving.  
NSD323Z  
R (Reverse):  
CAUTION  
NIC1649  
Shifting  
LHD models  
jA  
jB  
Shift into this position only after the vehicle has  
completely stopped.  
Gear shift indicator:  
RHD models  
The gear shift indicator jA located in the lower part  
of the vehicle information display shows the current  
position of the transmission.  
To move the selector lever:  
Use this position to reverse the vehicle.  
When the selector lever is in the R (Reverse) posi-  
tion, either the NISSAN Connect monitor (where fit-  
ted) or the ultra sonic parking sensor (where fitted)  
will be activated. For details, see “Rear-view moni-  
tor (where fitted)” in the “4. Display screen, heater  
It shows the P,R,N,D modes when the transmission  
is in auto mode. It shows the gear number when the  
transmission is in manual mode.  
Starting and driving 5-15  
Downloaded from manuals search engine  
When cancelling manual shift mode, return the  
selector lever to the D (Drive) position. The trans-  
mission returns to the normal driving mode.  
•
•
Manual shift mode  
When the selector lever is shifted from D (Drive) to  
the manual shift gate with the vehicle stopped or  
while driving, the transmission enters manual shift  
mode. Shift range can be selected manually.  
In manual shift mode, the transmission may  
not shift to the selected gear under certain  
circumstances. This helps maintain driving  
performance and reduces the chance of ve-  
hicle damage or loss of control.  
In manual shift mode, the selected gear is displayed  
on the position indicator in the combination meter.  
Shift ranges up or down one by one as follows:  
If the engine is revving up to a hazardous  
speed in manual shift mode, the transmission  
may shift up automatically. When the vehicle  
speed decreases, the transmission automati-  
cally shifts down and shifts to 1st gear before  
the vehicle comes to a stop.  
•
NSD347  
1st ⇔ 2nd ⇔ 3rd ⇔ 4th ⇔ 5th ⇔ 6th  
Cap (where fitted)  
When shifting up, move the selector lever to the  
+ (up) side. (Shifts to higher range).  
•
Shift lock release  
If the battery is discharged, the selector lever can-  
not be moved from the P (Park) position even with  
the brake pedal depressed and the ignition switch in  
the ON position.  
When shifting down, move the selector lever to  
the – (down) side. (Shifts to lower range).  
•
Accelerator downshift – In the D (Drive)  
position  
Moving the selector lever rapidly to the same  
side twice will shift the ranges in succession.  
•
For rapid passing or driving uphill, fully depress the  
accelerator pedal to the floor. This shifts the trans-  
mission down into a lower gear, depending on the  
vehicle speed.  
To move the selector lever, remove the cap j1  
(where fitted) then push the shift lock release button  
jA with a suitable tool j2 (as illustrated) and press  
the selector lever button j3 . It is now possible to  
move the selector lever to the N (Neutral) position  
j4 .  
Use the 1st position when driving slowly on steep  
•
hills, slow driving through deep snow, sand or  
mud, or for maximum engine braking on steep  
downhill grades.  
Use the 2nd, 3rd or 4th position when driving  
steep hills or for engine braking on steep down-  
hill grades.  
•
For your safety, make sure the handbrake is applied  
and the brake pedal is depressed during the opera-  
tion.  
Use the 5th position for driving up or down long  
slopes.  
•
If there is any problem moving the lever out of the P  
(Park) position, have a NISSAN dealer or qualified  
workshop to check the automatic transmission sys-  
tem as soon as possible.  
Use the 6th position for all normal forward driv-  
ing. However, you need to shift down the gears  
when accelerating or passing another vehicle.  
•
5-16 Starting and driving  
Downloaded from manuals search engine  
Avoid revving up the engine while the vehicle  
is stopped. This could cause unexpected ve-  
hicle movement.  
•
•
Fail-safe  
AT models:  
WARNING  
When the fail safe operation occurs, the vehicle  
speed may be lower than other traffic, which  
could increase the chance of a collision. Be es-  
pecially careful when driving. If necessary, drive  
to the side of the road at a safe place and away  
from traffic, to allow the transmission to return to  
normal operation, or have the transmission re-  
paired by a NISSAN dealer or qualified workshop,  
if necessary.  
When the fail-safe operation occurs, the AT CHECK  
indicator light comes on for 2 seconds and the auto-  
matic transmission will be locked in the third gear.  
Have a NISSAN dealer or qualified workshop check  
and repair the transmission.  
Never shift to either the P (Park) or R (Re-  
verse) position while the vehicle is moving.  
This could cause serious damage to the trans-  
mission.  
Start the engine in either the P (Park) or N  
(Neutral) position. The engine will not start in  
any other position. If it does, have your ve-  
hicle checked by a NISSAN dealer or qualified  
workshop.  
•
CVT models:  
When the fail-safe operation occurs, the vehicle  
speed will be decreased automatically to reduce the  
chance of transmission damage. Vehicle speed can  
be controlled with the accelerator pedal, but the  
engine power may be limited. Have a NISSAN dealer  
or qualified workshop check and repair the trans-  
mission.  
DRIVING WITH CONTINUOUSLY  
VARIABLE TRANSMISSION (CVT)  
(Models without manual shift)  
Shift into the P (Park) position and apply the  
handbrake when at a standstill for longer than  
a short waiting period.  
•
•
•
The Continuously Variable Transmission (CVT) in  
your vehicle is electronically controlled to produce  
maximum power and smooth operation.  
Keep the engine at idling speed while shifting  
from the N (Neutral) position to any driving  
position.  
AT or CVT models:  
If the vehicle is driven under extreme conditions,  
such as excessive wheel spinning and subse-  
quent hard braking, the Fail-safe system may be  
activated. This will occur even if all electrical cir-  
cuits are functioning properly. In this case, turn  
the ignition switch “OFF” and wait for 10 sec-  
onds. Then turn the key back to the ON position.  
The vehicle should return to its normal operating  
condition. If it does not return to its normal oper-  
ating condition have your NISSAN dealer or quali-  
fied workshop check the transmission and have  
the transmission repaired by a NISSAN dealer or  
qualified workshop, if necessary.  
The recommended operating procedures for this  
transmission are shown on the following pages. Fol-  
low these procedures for maximum vehicle perfor-  
mance and driving enjoyment.  
When stopping the vehicle on an uphill grade,  
do not hold the vehicle by depressing the ac-  
celerator pedal. The footbrake pedal should  
be depressed in this situation.  
WARNING  
Starting vehicle  
Do not downshift abruptly on slippery roads. This  
may cause a loss of control.  
1. After starting the engine, fully depress the foot-  
brake pedal before moving the selector lever out  
of the P (Park) position.  
CAUTION  
The cold engine idle speed is high, so use  
•
2. Keep the footbrake pedal depressed and move  
the selector lever to a driving position.  
caution when shifting the transmission into a  
forward or reverse position before the engine  
has warmed up.  
3. Release the handbrake, the footbrake pedal, and  
then gradually start the vehicle in motion.  
Starting and driving 5-17  
Downloaded from manuals search engine  
The CVT is designed so the footbrake pedal  
MUST be depressed before shifting from the P  
(Park) position to any driving position while the  
ignition switch is in the ON position.  
Shifting  
WARNING  
Apply the handbrake if the selector lever is in  
any position while the engine is not running.  
Failure to do so could cause the vehicle to  
move unexpectedly or roll away and result in  
serious personal injury or property damage.  
•
•
The selector lever cannot be moved out of the P  
(Park) position and into any of the other posi-  
tions if the ignition switch is placed in the LOCK,  
“OFF” or ACC position or if the key is removed.  
CAUTION  
If the selector lever cannot be moved from  
the P (Park) position while the engine is run-  
ning and the footbrake pedal is depressed,  
the stop lights may not work. Malfunctioning  
stop lights could cause an accident injuring  
yourself and others.  
NSD397  
DEPRESS THE FOOTBRAKE PEDAL - Shifting  
•
Left-Hand Drive (LHD) models  
the selector lever to D, R or L without de-  
pressing the footbrake pedal causes the ve-  
hicle to move slowly when the engine is run-  
ning. Make sure the footbrake pedal is de-  
pressed fully and the vehicle is stopped before  
shifting the selector lever.  
After starting the engine, fully depress the footbrake  
pedal, push the selector lever button and move the  
selector lever out of the P (Park) position.  
MAKE SURE OF THE SELECTOR LEVER POSI-  
•
TION - Make sure the selector lever is in the  
desired position. D and L are used to move  
forward and R to reverse.  
If the ignition switch is placed in the “OFF” or ACC  
position for any reason while the selector lever is in  
any positions other than the P (Park) position, the  
ignition switch cannot be placed in the LOCK posi-  
tion.  
NSD398  
WARM UP THE ENGINE - Due to the higher  
•
Right-Hand Drive (RHD) models  
idle speeds when the engine is cold, extra  
caution must be exercised when shifting the  
selector lever into the driving position imme-  
diately after starting the engine.  
If the ignition switch cannot be placed in the LOCK  
position, perform the following steps:  
Push the button jA while depressing  
the footbrake pedal.  
1. Apply the handbrake.  
Push the button jA .  
2. Place the ignition switch in the ON position while  
depressing the footbrake pedal.  
Just move the selector lever.  
3. Move the selector lever to the P (Park) position.  
4. Models with Intelligent Key system:  
5-18 Starting and driving  
Downloaded from manuals search engine  
Place the ignition switch in the “OFF” position.  
Models without Intelligent Key system:  
Place the ignition switch in the LOCK position.  
L (Low):  
ON position:  
Use this position when climbing steep hills slowly or  
driving slowly through deep snow, sand or mud, or  
for maximum engine braking on steep downhill  
grades.  
For driving up or down long slopes where engine  
braking is necessary, or for powerful acceleration,  
use the ON position. The transmission will automati-  
cally select a different gear ratio, allowing the en-  
gine to provide high output.  
P (Park):  
Use this position when the vehicle is parked or when  
starting the engine. Make sure that the vehicle is  
completely stopped and move the selector lever  
into the P (Park) position. Apply the handbrake.  
When parking on a hill, first depress the footbrake  
pedal, apply the handbrake, and then move the se-  
lector lever into the P (Park) position.  
When driving conditions change, push the switch to  
turn the SPORT mode off.  
Remember not to drive at high speeds for extended  
periods of time with the SPORT mode in the ON  
position. This reduces fuel economy.  
Accelerator downshift  
- in the D position -  
R (Reverse):  
Use this position to reverse. Make sure that the  
vehicle is completely stopped before selecting the R  
(Reverse) position.  
NSD399  
For passing or climbing hills, depress the accelera-  
tor pedal to the floor. This shifts the transmission  
down into a lower gear, depending on the vehicle  
speed.  
Left-Hand Drive (LHD) model  
SPORT mode switch  
When the selector lever is in the R (Reverse) posi-  
tion, either the NISSAN Connect monitor (where fit-  
ted) or the ultra sonic parking sensor (where fitted)  
will be activated. For details, see “Rear-view moni-  
tor (where fitted)” or “Around view monitor (where  
fitted)” earlier in this section or “Ultrasonic Parking  
Sensor (where fitted)” later in this section  
To select the SPORT mode, push the SPORT mode  
switch with the selector lever in the D (Drive) posi-  
tion. The SPORT mode indicator light  
in the  
meter panel illuminates. To turn off the SPORT  
mode, push the SPORT mode switch again. The  
SPORT mode indicator light will turn off. When the  
selector lever is shifted to any position other than D,  
the SPORT mode will be automatically turned off.  
N (Neutral):  
Neither the forward nor reverse gear is engaged.  
The engine can be started in this position. You may  
shift to the N (Neutral) position and restart a stalled  
engine while the vehicle is moving.  
OFF position:  
For normal driving and fuel economy, use the OFF  
position.  
NSD400  
D (Drive):  
Use this position for all normal forward driving.  
Starting and driving 5-19  
Downloaded from manuals search engine  
For models with Intelligent Key system: If the battery  
is discharged completely, the steering wheel cannot  
be unlocked. Do not move the vehicle with the steer-  
ing wheel locked.  
quent hard braking, the fail-safe system may be  
activated. This will occur even if all electrical cir-  
cuits are functioning properly. In this case, place  
the ignition switch in the “OFF” position and wait  
for 10 seconds. Then turn the ignition switch back  
to the ON position. The vehicle should return to  
its normal operating condition. If it does not re-  
turn to its normal operating condition, have a  
NISSAN dealer or qualified workshop check the  
transmission and repair it if necessary.  
Shift lock release  
LHD models  
j1  
j2  
jA  
RHD models  
If the selector lever cannot be moved out of the P  
(Park) position, have a NISSAN dealer or qualified  
workshop check the CVT system as soon as pos-  
sible.  
Shift lock release button  
If the battery charge is low or discharged, the selec-  
tor lever may not move from the P (Park) position  
even with the brake pedal depressed and the selec-  
tor lever button pushed.  
WARNING  
To move the selector lever, perform the following  
procedure:  
If the selector lever cannot be moved from the P  
(Park) position while the engine is running and  
the brake pedal is depressed, the stop lights may  
not work. Malfunctioning stop lights could cause  
an accident injuring yourself and others.  
WARNING  
When the fail-safe operation occurs, vehicle  
speed may be gradually reduced. The reduced  
speed may be lower than other traffic, which  
could increase the chance of a collision. Be es-  
pecially careful when driving. If necessary, pull to  
the side of the road at a safe place and allow the  
transmission to return to normal operation, or  
have it repaired if necessary.  
1. Models with Intelligent Key system:  
Place the ignition switch in the “OFF” or LOCK  
position.  
High fluid temperature protection mode  
Models without Intelligent Key system:  
This transmission has a high fluid temperature pro-  
tection mode. If the fluid temperature becomes too  
high (for example, when climbing steep grades in  
high temperature with heavy loads, such as when  
towing a trailer), engine power and, under some  
conditions, vehicle speed will be decreased auto-  
matically to reduce the chance of transmission dam-  
age. Vehicle speed can be controlled with the ac-  
celerator pedal, but engine and vehicle speed may  
be limited.  
Place the ignition switch in the LOCK position,  
and remove the key if it is inserted.  
2. Apply the handbrake.  
3. Push down the shift lock release button jA . Use  
a suitable tool.  
4. Push and hold the selector lever button and move  
the selector lever to the N (Neutral) position while  
holding down the shift lock release button.  
Place the ignition switch in the ON position to un-  
lock the steering wheel. The vehicle may be moved  
to the desired location.  
Fail-safe  
When the fail-safe operation occurs, the CVT will  
not be shifted to the selected driving position.  
If the vehicle is driven under extreme conditions,  
such as excessive wheel spinning and subse-  
5-20 Starting and driving  
Downloaded from manuals search engine  

Related Topics

Running-in schedule Before starting the engine Precautions when starting and driving Exhaust gas (Carbon Monoxide) On-pavement and off-road driving precautions Three-way catalyst (Petrol engine models) To help prevent damage Turbocharger system (Diesel engine models) Diesel Particulate Filter (DPF) (where fitted) Regeneration restrictions If regeneration fails Care when driving Engine cold start period Loading luggage Driving on wet roads Driving under winter conditions Ignition switch Automatic transmission or Continuously variable transmission Steering lock Key positions Ignition knob (where fitted) Manual transmission Ignition knob position Emergency key ? Intelligent Key dead battery situation NISSAN Anti-Theft System (NATS) Starting the engine Driving with manual transmission Driving with automatic transmission or with continuously variable transmission (Models with manual shift) Driving with Continuously Variable Transmission (CVT) (Models without manual shift) Stop/Start System (where fitted) Normal operation Precautions Stop/Start System OFF switch Environmental savings Ultrasonic Parking Sensor (where fitted) Four-wheel Drive (4WD) (where fitted) 4WD mode operations 4WD shift tips 4WD Warning light 4WD Mode indicator lights Driving four-wheel drive (4WD) safely Cruise control (where fitted) Precautions on cruise control Cruise control system operations Speed limiter Speed limiter operations Parking Trailer towing Operating precautions Tyre pressure Safety chains Trailer brakes Trailer detection (where fitted) Installation of coupling device Vehicle security Power steering system Brake system Brake precautions Anti-lock Braking System (ABS) Electronic Stability Programme (ESP) system (where fitted) Electronic Stability Programme (ESP) OFF switch Cold weather driving Battery Engine coolant Tyre equipment Special winter equipment Corrosion protection

Popular Owner Manuals