Advertisement

Advertisement

Download User Manual App

Quickly access user manual for free!

Generator -> Ribbed Belt Pulley with Freewheel, Removing and Installing for Your Audi A1 SUV 2010-2017

Audi A1 2011 ➤ , Audi A1 Sportback 2018 ➤ , Audi A2 2001 ➤ , Audi A3 20 ...  
Electrical Equipment General Information - Edition 08.2019  
Removing  
– Remove the generator if necessary. Refer to ⇒ Electrical  
Equipment; Rep. Gr. 27 ; Generator; Generator, Removing  
and Installing .  
– For some engine types the removal can be performed with the  
generator still installed, here only the ribbed belt must have  
the tension released and be removed.  
– If present, press the protective cap off the generator pulley.  
– Counterhold nut using -3310- and rotate generator shaft clock‐  
wise to loosen it.  
– Remove ribbed belt pulley.  
Installing  
Install in reverse order of removal. Note the following:  
– Turn the generator shaft counterclockwise to tighten.  
– Clip protective cap onto generator pulley.  
Tightening specification  
Component  
Nm  
65  
Ribbed belt pulley to generator  
4.15  
Ribbed Belt Pulley with Freewheel, Re‐  
moving and Installing  
Special tools and workshop equipment required  
♦ Torque Wrench 1332 40-200Nm - VAG1332-  
♦ Adapter - T10474-  
♦ Multi-Tooth Adapter - 3400-  
♦ Socket - 3400/1-  
General Information  
There are different ribbed belt pulley with freewheel.  
Before removing check which special tool must be used for the  
removal of the ribbed belt pulley with freewheel.  
Caution  
The length of the ribbed belt is different depending on the rib‐  
bed belt pulley with freewheel installed.  
Check which ribbed belt pulley with freewheel is installed and  
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not  
make sure that the correct ribbed belt will be installed. For the  
ribbed belt allocation. Refer to the PapretsrmCitteadtuanlloesgs a.uthorised by AUDI AG. AUDI AG does not guarantee or accept any liability  
with respect to the correctness of information in this document. Copyright by AUDI AG.  
Characteristics of the Ribbed Belt Pulley with Freewheel  
-A- small ribbed belt pulley with freewheel, special tool to be used  
-T10474- or -3400/1-  
4. Generator  
71  
Audi A1 2011 ➤ , Audi A1 Sportback 2018 ➤ , Audi A2 2001 ➤ , Audi A3 20 ...  
Electrical Equipment General Information - Edition 08.2019  
-B- large ribbed belt pulley with freewheel, special tool to be used  
-3400-  
Note  
The ribbed belt for the large ribbed belt pulley with freewheel must  
be larger because it has a larger diameter.  
Removing  
– Remove the generator if necessary. Refer to ⇒ Electrical  
Equipment; Rep. Gr. 27 ; Generator; Generator, Removing  
and Installing .  
– For some engine types the removal can be performed with the  
generator still installed, here only the ribbed belt must have  
the tension released and be removed.  
– Clamp the generator in a vise at the mounting points.  
– If equipped, remove the protective cap from the decoupling  
belt pulley with freewheel.  
– Install the -T10474- or -3400- -1- in the belt pulley and attach  
a wrench.  
– Place a suitable tool -2- in the generator shaft.  
– Turn the generator shaft clockwise in direction of -arrow- to  
loosen and while doing so counterhold with the wrench.  
– Hold the ribbed belt pulleyPwroittehctefrdebey wcophyerigehlt.inCoppyliangcfeorbpryivahteaonrdcoamnmdercial purp
permitted unless authorised by AUDI AG. AUDI AG does not g
turn it at the generator shaft until the ribbed belt pulley with  
with respect to the correctness of information in this docume
freewheel can be removed.  
Installing  
Install in reverse order of removal. Note the following:  
The -VAG1332- must be rearranged for installing the decoupling  
belt pulley with freewheel as follows:  
– Release the insert -1- and remove it from the handle part -2-.  
– Turn the handle part -2- of the torque wrench 180° and reinsert  
the socket.  
– Set the rotation direction of the torque wrench socket to "left".  
– Next, screw the ribbed belt pulley with freewheel by hand onto  
the generator shaft until stop.  
– Install the -T10474- -1- ribbed belt pulley with freewheel and  
attach the wrench.  
72  
Rep. Gr.27 - Starter, Generator and Cruise Control  

Related Topics