Get Descriptions of work -> Service interval display: Resetting Guide for Volkswagen Lupo 2 Door First Generation (1998-2005)

Lupo 1999 ➤ , Lupo 3L 1999 ➤

Maintenance - Edition 03.2018

4.13

Automated manual gearbox (DSG):

Carrying out basic setting

– Carry out basic setting of automated manual gearbox (DSG):

⇒ Vehicle diagnostic tester; vehicle diagnosis, testing and in‐

formation system or the - VAS 5051- or the vehicle diagnosis

and service information system - VAS 5052- in function “gui‐

ded fault finding”.

Procedure: »5-speed manual gearbox 085 DS« ⇒ 5-speed man‐

ual gearbox 085 DS ; Rep. gr. 34 ; Controls, housing; Changing

oil and filter of dual clutch gearbox »Controls, housing; Changing

oil and filter of dual clutch gearbox«

4.14

Service interval display: Resetting

Function

The service interval display electronics is comprised of, amongst

other items:

♦ a time recorder

and

♦ two distance recorders.

The electronics evaluates both recorders so that the customer

♦ after a predetermined time period is exceeded or

or

♦ after a predetermined distance is reached

is informed via the service interval display that a service is re‐

quired (whichever occurs first).

Service interval display

Between services, only the total distance and distance travelled

(trip recorder) is shown in the distance display -2-.

If a service is due, the following is indicated in the distance display

-2- below the total mileage:

♦ with ignition switched off “service”

♦ after the ignition is switched on and up to 3 minutes after the

engine is started the type of service (see table).

Note

After the engine is started the display switches back to “service”

after 3 minutes.

4. Descriptions of work:

43

Lupo 1999 ➤ , Lupo 3L 1999 ➤

Maintenance - Edition 03.2018

Service type:

Type of Service:

(indicated on display):

Mileage and service OIL

Oil change service every

15,000 km

or:

Mileage and service INSP

Inspection service every 12

months or every 30,000 km

(whichever occurs first)

One or both service types must be reset depending on which

service was completed, therefore:

♦ If a “service OIL” (oil change service every 15,000 km) is car‐

ried out, only “service OIL” must be reset.

♦ If a “service INSP” (inspection service every 12 months or ev‐

ery 30,000 km) has been performed “service INSP” and “serv‐

ice OIL” must be reset.

♦ If a “service INSP” (inspection service every 12 months or ev‐

ery 30,000 km) without an oil change has been performed,

then only “service INSP” must be reset.

The service interval display can be reset using one of two meth‐

ods:

♦ With adjustment button for the distance display on dash panel

insert ⇒ page 44 ,

or using

♦ vehicle diagnosis, testing and information system - VAS 5051-

or vehicle diagnosis and service information system - VAS

5052- ⇒ page 45 .

4.14.1

Resetting service interval display with

adjustment button for distance display

on dash panel insert

The service interval display must be reset (adapted) during

♦ delivery inspection

♦ every oil change service

♦ every inspection

!

Note

Each service must be reset individually as only the distance re‐

corder and time counter of the actual service can be reset.

Reset the display as follows:

– Switch off ignition.

44

4. Descriptions of work:

Lupo 1999 ➤ , Lupo 3L 1999 ➤

Maintenance - Edition 03.2018

– Press and hold button -1- below speedometer.

– Switch on ignition and hold button -1- depressed (min. 10 sec‐

onds) until three dashes (- - -) or the next service appears in

the display. Only then the service is reset.

– Release button -1-.

– Switch off ignition.

After resetting the service interval display the previous trip re‐

corder display is indicated again.

Note

♦ Note that only the actual service type indicated on display can

be reset.

♦ To reset a further service, repeat these steps.

4.14.2

Reset service interval display vehicle di‐

agnosis, testing and information system

- VAS 5051- or vehicle diagnosis and

service information system - VAS 5052-

The service interval display must be reset (adapted) during

♦ delivery inspection

♦ every oil change service

♦ every inspection

.

Special tools and workshop equipment required

♦ Vehicle diagnostic, testing and information system - VAS

5051-

♦ Diagnostic cable - VAS 5051/6A-

4. Descriptions of work:

45

Lupo 1999 ➤ , Lupo 3L 1999 ➤

Maintenance - Edition 03.2018

♦ Vehicle diagnostic and service information system - VAS

5052-

♦ Diagnostic cable, 2 m - VAS 5052/3 A-

Note

Ensure that the fault reader is only used with the respective di‐

agnostic cable.

Connect vehicle diagnosis, testing and information system - VAS

5051- or vehicle diagnosis and service information system - VAS

5052- .

– Apply handbrake.

– Automatic gearbox: Move selector lever to position “P” or “N”.

– Manual gearbox: gear lever in neutral.

– Dual clutch gearbox: Move selector lever to position “N” or

“STOP”.

Connect vehicle diagnostic, testing and information system - VAS

5051- or vehicle diagnostic and service information system - VAS

5052- with ignition switched off as follows:

– Lever cover or ashtray insert out of centre console.

– Connect vehicle diagnosis, testing and information system -

VAS 5051- or vehicle diagnosis and service information sys‐

tem - VAS 5052- using diagnostic cable - VAS 5051/6A- with

ignition switched off.

– Switch on ignition.

46

4. Descriptions of work:

Lupo 1999 ➤ , Lupo 3L 1999 ➤

Maintenance - Edition 03.2018

Indicated on display:

Select operating mode:

– Press button for Vehicle self-diagnosis on display

-arrow-.

Note

If the display is not as shown in the procedure: ⇒ Operating in‐

structions for vehicle diagnostic, testing and information system -

VAS 5051A- or ⇒ Operating instructions for vehicle diagnostic

and service information system - VAS 5052- .

Indicated on display:

Select vehicle system:

– Press “17 - Dash panel insert” on display -arrow-.

Indicated on display:

The control unit identification and coding are displayed -arrow-.

Indicated on display:

– Press “10 - Adaption” on display -arrow-.

4. Descriptions of work:

47

Lupo 1999 ➤ , Lupo 3L 1999 ➤

Maintenance - Edition 03.2018

Indicated on display:

– Press the adaption channel for the service which is to be reset

on the display number block -arrow-:

♦ for display “service OIL” on dash panel insert channel 10

♦ for display “service INSP” on dash panel insert channel 10, 11

and 12

Adaption table:

Type of service:

Adaption channel:

Counter contents:

Adaption value to

reset:

service OIL

service INSP

10

11

12

Distance in 100s of km

Time in days

150

300

360

Note

♦ Entering the relevant adaption values for the distance recorder

is only possible in steps of 100 km. Therefore this is shown on

the display in 100 km.

♦ The entered values count down to 0 km.

♦ The counter for “INSP service” can be adapted to max. 360

days.

Resetting service interval display

service OIL (oil change service) ⇒ page 48

service INSP (inspection every 12 months) ⇒ page 49

service INSP (inspection every 30,000 km) ⇒ page 51

4.14.3

Service OIL (oil change service)

Indicated on display:

– Press buttons 1 and 0 on display number block -arrow-.

– Confirm entry with Q key on display number block.

48

4. Descriptions of work:

Lupo 1999 ➤ , Lupo 3L 1999 ➤

Maintenance - Edition 03.2018

Indicated on display:

– Move the position indicator -arrow- on the display until 150 is

displayed over the scroll bar -1- (equates to 15,000 km).

Note

♦ Pressing the scroll bar briefly to the right -2- of the position

indicator moves the value to the next number.

♦ Pressing the scroll bar briefly on the left -3- of the position in‐

dicator moves the value to the previous number.

– Press the Save button on display -4-.

Indicated on display:

– Press the Accept button on display -arrow-.

– End output.

4.14.4

Service INSP (inspection every 12

months)

Indicated on display:

– Press buttons 1 and 2 on display number block -arrow-.

– Confirm entry with Q key on display number block.

4. Descriptions of work:

49

Lupo 1999 ➤ , Lupo 3L 1999 ➤

Maintenance - Edition 03.2018

Indicated on display:

– Move the position indicator -arrow- on the display until -1- 360

is displayed over the scroll bar (equates 360 days).

Note

♦ Pressing the scroll bar briefly to the right -2- of the position

indicator moves the value to the next number.

♦ Pressing the scroll bar briefly on the left -3- of the position in‐

dicator moves the value to the previous number.

– Press the Save button on display -4-.

Indicated on display:

– Press the Accept button on display -arrow-.

If an inspection service was performed without oil change, end

output.

If an inspection service was performed with an oil change, con‐

tinue as follows:

Indicated on display:

– Press ← -arrow- on display.

Indicated on display:

– Press “10 - Adaption” on display -arrow-.

50

4. Descriptions of work:

Lupo 1999 ➤ , Lupo 3L 1999 ➤

Maintenance - Edition 03.2018

Indicated on display:

– Press buttons 1 and 0 on display number block -arrow-.

– Confirm entry with Q key on display number block.

Indicated on display:

– Move the position indicator -arrow- on the display until 150 is

displayed over the scroll bar -1- (equates to 15,000 km).

Note

♦ Pressing the scroll bar briefly to the right -2- of the position

indicator moves the value to the next number.

♦ Pressing the scroll bar briefly on the left -3- of the position in‐

dicator moves the value to the previous number.

– Press the Save button on display -4-.

Indicated on display:

– Press the Accept button on display -arrow-.

– End output.

4.14.5

Service INSP (inspection every 30,000

km)

Indicated on display:

– Press buttons 1 and 1 on display number block -arrow-.

– Confirm entry with Q key on display number block.

4. Descriptions of work:

51

Lupo 1999 ➤ , Lupo 3L 1999 ➤

Maintenance - Edition 03.2018

Indicated on display:

– Move the position indicator -arrow- on the display until 300 is

displayed over the scroll bar -1- (equates to 30,000 km).

Note

♦ Pressing the scroll bar briefly to the right -2- of the position

indicator moves the value to the next number.

♦ Pressing the scroll bar briefly on the left -3- of the position in‐

dicator moves the value to the previous number.

– Press the Save button on display -4-.

Indicated on display:

– Press the Accept button on display -arrow-.

For the inspection every 30,000 km, also the inspection service

every 12 months and the oil change service must be reset as fol‐

lows:

Indicated on display:

– Press ← -arrow- on display.

Indicated on display:

– Press “10 - Adaption” on display -arrow-.

52

4. Descriptions of work:

Lupo 1999 ➤ , Lupo 3L 1999 ➤

Maintenance - Edition 03.2018

Indicated on display:

– Press buttons 1 and 2 on display number block -arrow-.

– Confirm entry with Q key on display number block.

Indicated on display:

– Move the position indicator -arrow- on the display until -1- 360

is displayed over the scroll bar (equates 360 days).

Note

♦ Pressing the scroll bar briefly to the right -2- of the position

indicator moves the value to the next number.

♦ Pressing the scroll bar briefly on the left -3- of the position in‐

dicator moves the value to the previous number.

– Press the Save button on display -4-.

Indicated on display:

– Press the Accept button on display -arrow-.

Indicated on display:

– Press ← -arrow- on display.

4. Descriptions of work:

53

Lupo 1999 ➤ , Lupo 3L 1999 ➤

Maintenance - Edition 03.2018

Indicated on display:

– Press “10 - Adaption” on display -arrow-.

Indicated on display:

– Press buttons 1 and 0 on display number block -arrow-.

– Confirm entry with Q key on display number block.

Indicated on display:

– Move the position indicator -arrow- on the display until 150 is

displayed over the scroll bar -1- (equates to 15,000 km).

Note

♦ Pressing the scroll bar briefly to the right -2- of the position

indicator moves the value to the next number.

♦ Pressing the scroll bar briefly on the left -3- of the position in‐

dicator moves the value to the previous number.

– Press the Save button on display -4-.

Indicated on display:

– Press the Accept button on display -arrow-.

– End output.

End output

54

4. Descriptions of work:

Lupo 1999 ➤ , Lupo 3L 1999 ➤

Maintenance - Edition 03.2018

Indicated on display:

– Press GoTo button on display -arrow-.

Indicated on display:

– Press the End button on display -arrow-.

– Press End button in End menu.

– Switch off ignition and separate diagnosis connections.

– Switch on ignition.

After the ignition is switched on, the type of service is no longer

displayed in the distance display in the dash panel insert.

The service interval display is now reset.

– Switch off ignition.

– Install cover in centre console or ashtray insert.

4.15

Door arrester: grease.

Carry out following procedure:

– Grease door arrester at points shown -arrows-.

– Grease door arrester in side area -arrow A- with grease -G

000 150- .

4.16

Sunroof: checking function, cleaning

and greasing guide rails

Carry out following procedure:

– Check function of sunroof.

4. Descriptions of work:

55

Descriptions of work -> Service interval display: Resetting for Your Volkswagen Lupo 2 Door First Generation (1998-2005)

Related Topics

Popular Owner Manuals

Latest Owner Manuals