Get Driving -> Adaptive cruise control Guide for Peugeot 5008 SUV Third Generation (2024-2025)

Driving

For more information on Adaptive cruise

control and Lane positioning assist, refer to

the corresponding sections.

The availability of the system depends on the

country you are driving in.

This system is only to be used on eligible

motorways and main roads.

► After a few seconds, the Drive Assist Plus

mode is selected. The Driving aids area is

displayed on the instrument panel.

The colour of the symbols,

representing the steering wheel

and the side lines, depends on the

operating state of the system:

The system assists the driver by acting

on the steering, acceleration and braking

within the physical limits and capacities

of the vehicle. Certain road infrastructure

elements or vehicles in the surroundings

may not be properly seen or may be poorly

interpreted by the camera and radar, resulting

in an unexpected change in direction, a lack

of steering correction and/or inappropriate

management of acceleration or braking.

Selecting/Deselecting the

system

(grey) One or more operating con-

ditions is not met; the system is

paused.

It is configured in the ADAS touch

screen application.

(green) All operating conditions are

met; the system is active.

► Select the Functions tab, then select/

deselect Drive Assist.

(orange) System malfunction.

The system's status is saved when the ignition is

switched off.

Primarily designed for driving on main

roads and motorways, this system only

works with moving vehicles driving in the

same direction as your vehicle.

Adaptive cruise control

► Press this button successively again until the

OFF mode is displayed on the instrument

panel.

For more information, refer to the General

recommendations on the use of driving

and manoeuvring aids and the Specific

recommendations on cruise control.

Selecting/Deselecting the

system

► After a few seconds, the Drive Assist Plus

mode is deselected. The Driving aids area

disappears.

This system automatically maintains the vehicle

speed at a value set by the driver (speed

setting), while respecting a safety distance from

the vehicle in front (target vehicle) previously set

by the driver. The system automatically manages

the acceleration and deceleration of the vehicle.

With the Stop function (with the EAT6

automatic gearbox), the system manages

braking until the vehicle comes to a complete

stop.

Drive Assist Plus 2.0

This system automatically regulates the speed

and corrects the trajectory of the vehicle by

combining the following functions:

– Drive Assist Plus with Adaptive cruise control

with Stop&Go function and Lane positioning

assist.

ASSIST

► Press this button successively until the

Drive Assist Plus mode is displayed on the

instrument panel.

– Semi-automatic lane changing.

– Speed setting advance recommendation.

For more information on these functions, refer to

the corresponding sections.

With the Stop & Go function (with the e-

DCS6/7 automatic gearbox or drive selector), the

136

Driving

system manages braking until the vehicle comes

to a complete stop and restarts the vehicle.

For more information on the Road signs

recognition function, refer to the corresponding

section.

Steering-mounted controls

The brake lamps come on if the vehicle is

slowed down by the system.

The system is not operational in the event of

a brake lamp failure.

Information displayed on

the instrument panel

To do this, the system uses a camera fitted at

the top of the windscreen and a radar fitted in

the front bumper.

1. Selection/Deselection of cruise control only

or Drive Assist Plus (depending on version)

2. Switch on/Pause cruise control at the

previously saved speed setting

Primarily designed for driving on main

roads and motorways, this system only

works with moving vehicles driving in the

same direction as your vehicle.

Confirmation of vehicle restart after

automatic stop (version with Stop & Go

function)

If the driver activates the direction indicator

to overtake a slower vehicle, cruise control

may temporarily reduce the distance to the

target vehicle to facilitate overtaking, without

exceeding the speed setting.

3. Increase the speed setting (if cruise control

activated) Activation of cruise control in

progress (if cruise control deactivated)

4. Decrease the speed setting (if cruise

control activated) Activation of cruise

control in progress (if cruise control

deactivated)

7. Cruise control activated (green)/paused

(grey)

8. Speed setting value

9. Speed suggested by the Road signs

recognition function

10. Vehicle held stationary (version with

Stop&Go function)

5. Activation of cruise control in progress

Use the speed suggested by the Road

signs recognition function

11. Inter-vehicle distance setting

12. Position of the vehicle detected by the

system

6. Display and configuration of the inter-

vehicle distance setting

137

Driving

With an automatic gearbox or a drive selector,

following braking that has brought the vehicle

to a complete stop, if the traffic conditions do

not allow the vehicle to begin moving again

within 3 seconds of stopping, press 2-II> or the

accelerator pedal to move off.

► For steps of +/- 5 mph (5 km/h), press and

Use

Selecting the system

hold on 3 to increase or 4 to decrease.

Prolonged pressing and holding on 3 or 4

causes a rapid change in vehicle speed.

► With the engine running, press successively

on 1-ASSIST until cruise control mode is

displayed on the instrument panel.

When the function is activated, the speed

setting value can be changed using the speed

suggested by the Road signs recognition

function displayed on the instrument panel:

– When passing the sign:

Cruise control remains active following a

gear change.

► After a few seconds, cruise control mode is

selected. The Driving aids area is displayed

(grey) and cruise control is ready to be

activated.

When cruise control is paused and the

driver tries to reactivate it, the message

"Activation not possible, conditions not

met" is temporarily displayed if reactivation is

impossible (required conditions not met).

► Press 5-OK to save the suggested speed.

Switching on cruise control

With an automatic gearbox or a drive selector,

your speed must be between 0 and 112 mph (0

and 180 km/h).

This value is then immediately shown as the new

speed setting on the instrument panel.

– After passing the sign:

System activation is also subject to the following

conditions:

– Driver's door closed.

► Press 5-OK. The message "OK?" is

Changing the programmed speed setting

with the Road signs recognition function

displayed to confirm the request to save.

► Press 5-OK again to save the suggested

speed. The new speed setting value is

displayed on the instrument panel.

– Driver's seat belt fastened.

– Mode D selected on the automatic gearbox.

– Parking brake released.

– If the vehicle is stationary, brake pedal

depressed.

► Press 5-OK to accept the speed suggested

by the function on the instrument panel, then

press again to confirm.

Pausing/Resumption of cruise control

If the selected speed is far from

the current vehicle speed, a strong

acceleration or deceleration is felt.

A message OK? is displayed if all activation

conditions are met.

► Press 2-II> or depress the brake pedal.

The symbol "II>" is displayed if all activation

conditions are met.

Cruise control may also have been paused:

– automatically, if the electronic stability control

(ESC) system is triggered.

– by shifting to neutral or engaging reverse gear.

– by using the electric parking brake.

– by unfastening the seat belt.

► Press 3, 4 or 5-OK: the current speed

becomes the speed setting (minimum 19

mph (30 km/h)) and cruise control is

immediately activated (green display).

Changing the inter-vehicle distance

► Press 6 to display the distance

setting thresholds ("Distant", "Normal"

or "Close"), then make successive short

presses to select a threshold.

Modifying the speed setting

To change the speed setting using the vehicle’s

current speed:

After a few seconds, the option is accepted and

will be memorised when the ignition is switched

off.

The driver must keep a sufficient safety distance

from the vehicle in front.

– by opening the driver's door.

► For steps of +/- 1 mph (1 km/h), make

successive short presses on 3 to increase or

4 to decrease.

► Press 2-II> or 5-OK to reactivate cruise

control.

138

Driving

(grey)/(grey)

All the operating conditions

are met.

Cruise control active, vehi-

cle detected.

The system has brought the vehicle to a

complete stop and is keeping it immobilised:

cruise control is paused.

The driver must accelerate to move off again,

then reactivate cruise control.

Temporarily exceeding the speed setting

► Depress the accelerator pedal. The system

is suspended as long as the acceleration is

maintained. When the accelerator pedal is

released, the speed setting flashes while the

current vehicle speed is above the speed

setting.

Stop & Go function

Cruise control suspended,

following brief acceleration

by the driver.

The system has brought the

vehicle to a complete stop.

Deselecting the system

(green)/(green)

(grey)/(green)

► Press successively on 1-ASSIST until OFF

(green)/

(green)

(orange)

"Take control"

mode is displayed on the instrument panel.

► After a few seconds, cruise control mode

is deselected. The Driving aids area

disappears.

Within 3 seconds of stopping, the vehicle

gradually and automatically begins moving

again.

Beyond 3 seconds of stopping, the driver must

accelerate or press 2-II> to move off.

► Brake or accelerate, depending on the

context.

Messages and alerts

(red)

"Take control"

The actual order of display of the

messages or alerts may be different.

If the driver takes no action after the

vehicle has been stopped, the electric

parking brake is applied automatically after

about 5 minutes.

Cruise control selected, but

cannot be activated.

All the operating conditions

have not been met.

Cruise control selected,

awaiting confirmation for

activation.

► Take back control of the vehicle

immediately: the system cannot manage the

current driving situation.

While the vehicle is immobilised, the

following recommendations apply:

– The driver should not leave the vehicle.

– Do not open the boot.

– Do not drop off or pick up passengers.

– Do not engage reverse gear.

"Activation not possible, condi-

tions not met"

All the operating conditions

are met.

Cruise control paused, but

cannot be reactivated.

All the operating conditions

have not been met.

(grey)

The system refuses to activate cruise control, as

the necessary conditions are not fulfilled.

Stop function

When restarting the vehicle, beware of

cyclists, pedestrians or animals who are

not taken into account by the system.

The driver must monitor their surroundings.

"Cruise paused" (for a few

seconds).

Cruise control paused,

awaiting confirmation for

reactivation.

(grey)/(green)

139

Driving

Operating limits

If any of the following malfunctions occurs,

do not use the system:

– Following an impact on the windscreen

close to the camera or on the front bumper.

– If a brake lamp is not working.

Cruise control operates by day and night, in dry

weather or moderate rainfall.

Certain situations cannot be managed by the

system and require driver intervention.

– When following a narrow vehicle.

Reactivate the system when conditions allow.

Cases not taken into account by the

system:

If the vehicle has undergone any of the

following modifications, do not use the

system:

– Carrying long objects on roof bars.

– Towing.

– Front end of the vehicle modified (for

example by adding long-range headlamps or

painting the front bumper).

Situations in which the driver is prompted

to immediately resume control:

– Pedestrians, cyclists, animals.

– Stationary vehicles (e.g. traffic jams,

breakdown).

– Excessively sharp deceleration by the vehicle

in front of you.

– Obstructed radar and/or camera.

Malfunction

– Vehicles crossing your lane.

– Vehicles driving in the opposite direction.

– When a vehicle cuts in sharply between your

vehicle and the one in front.

In the event of a malfunction, dashes are

displayed (orange) instead of the speed setting.

Situations where the driver must suspend

the system:

This warning lamp comes on, accom-

panied by a message and an audible

signal, to confirm the malfunction.

Some vehicles on the road may be poorly

perceived or interpreted by the camera

and/or the radar (e.g. truck), which can lead

to an incorrect evaluation of distances and

result in inappropriate acceleration or braking

of the vehicle.

Have it checked by a PEUGEOT dealer or a

qualified workshop.

Pay particular attention:

– When motorcycles are present and

when there are vehicles staggered across the

traffic lane.

– Vehicles in a tight bend.

– When approaching a roundabout.

– When entering a tunnel or crossing a

bridge.

140

Download User Manual App

Driving -> Adaptive cruise control for Your Peugeot 5008 SUV Third Generation (2024-2025)

Related Topics

Driving

Popular Owner Manuals

Latest Owner Manuals