2024-2026 Lexus LBX SUV Driving -> AHB (Automatic High Beam) User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Driving -> AHB (Automatic High Beam) for Your Lexus LBX SUV First Generation (2024-2026)

218
4-3. Operating the lights and wipers
1 Press the Automatic High Beam
switch.
2 Turn the headlight switch to the
or position.
When the headlight switch lever is in the
low beam position, the AHB system will be
enabled and the AHB indicator will illumi-
nate.
■ Automatic operating conditions of the
high beams
● When all of the following conditions are
met, the high beams will illuminate auto-
matically:
• The vehicle speed is approximately 30
km/h (19 mph) or more.
• The area ahead of the vehicle is dark.
• There are no vehicles ahead with lights
on.
• There are few streetlights or other lights
on the road ahead.
● If any of the following conditions are met,
the headlights will change to the low
beams:
• Vehicle speed drops below approxi-
mately 25 km/h (16 mph).
• The area ahead of the vehicle is not dark.
• There is a vehicle ahead with lights on.
• There are many streetlights or other
lights on the road ahead.
■ Front camera detection
● In the following situations, the high beams
may not be automatically changed to the
low beams:
• When a vehicle cuts in front of your vehi-
cle
• When another vehicle crosses in front of
the vehicle
• When vehicles ahead are repeatedly
AHB (Automatic High
Beam)
The Automatic High Beam uses a
front camera located on the upper
portion of the windshield to detect
the brightness of the lights of vehi-
cles ahead, streetlights, etc., and
automatically changes the head
lights between the high beams and
low beams.
WARNING
■ For safe use
Do not overly rely on the Automatic
High Beam. Always drive safely, taking
care to observe your surroundings and
turning the high beams on or off manu-
ally if necessary.
■ To prevent incorrect operation of the
Automatic High Beam system
When it is necessary to disable the sys-
tem: P.233
Using the Automatic High Beam
system
219
4
4-3. Operating the lights and wipers
Driving
detected and then hidden due to
repeated curves, road dividers or road-
side trees
• When a vehicle ahead approaches from
a far lane
• When a vehicle ahead is far away
• When a vehicle ahead has no lights
• When the lights of a vehicle ahead are
dim
• When a vehicle ahead is reflecting strong
light, such as own headlights
• Situations in which the sensors may not
operate properly: P.238
● The headlights may change to the low
beams if a vehicle ahead that is using fog
lights without its headlights turned on is
detected.
● House lights, street lights, traffic signals,
and illuminated billboards or signs may
cause the high beams to change to the
low beams, or the low beams to remain
on.
● The following may change the timing at
which the headlights change to the low
beams:
• The brightness of lights of vehicles ahead
• The movement and direction of vehicles
ahead
• The distance between the vehicle and a
vehicle ahead
• When a vehicle ahead only has lights illu-
minated on one side
• When a vehicle ahead is a two-wheeled
vehicle
• The condition of the road (gradient,
curve, condition of the road surface, etc.)
• The number of passengers and amount of
luggage
● The headlights may change between the
high beams and low beams unexpect-
edly.
● Bicycles and other small vehicles may not
be detected.
● In the following situations, the system may
not be able to correctly detect the bright-
ness of the surroundings. This may cause
the low beams to remain on or the high
beams to flash or dazzle pedestrians or
vehicles ahead. In such a case, it is neces-
sary to manually change between the
high beams and low beams.
• When there are lights similar to head-
lights or tail lights in the surrounding area
• When headlights or tail lights of vehicles
ahead are turned off, dirty, changing
color, or not aimed properly
• When the headlights are repeatedly
changing between the high beams and
low beams.
• When use of the high beams is inappro-
priate or when the high beams may be
flashing or dazzling pedestrians or other
drivers.
• When the vehicle is used in an area in
which vehicles travel on the opposite side
of the road of the country for which the
vehicle was designed, for example using
a vehicle designed for right-hand traffic in
a left-hand traffic area, or vice versa
• When it is necessary to disable the sys-
tem: P.233
• Situations in which the sensors may not
operate properly: P.238
■ Changing to the high beams
Push the lever forward.
The AHB indicator will turn off and the
high beam indicator will turn on.
Pull the lever to its original position to
enable the Automatic High Beam system
again.
■ Changing to the low beams
Press the Automatic High Beam
Turning the high beams on/off
manually
220
4-3. Operating the lights and wipers
switch.
The AHB indicator will turn off.
Press the switch to enable the Automatic
High Beam system again.
It is recommended to switch to the low
beams when use of the high beams is
inappropriate or when the high beams
may cause problems or distress to
other drivers or pedestrians nearby.
Pull the lever rearward and then return
it to its original position.
The high beams will illuminate while the
lever is pulled, however, after the lever is
returned to its original position, the low
beams will remain on for a certain amount
of time. After this, the Automatic High
Beam system will operate.
Rear fog light switch
1 Turns the rear fog lights off
2 Turns the rear fog lights on
Releasing the switch ring returns it to .
Operating the switch ring again turns the
rear fog lights off.
Temporarily switching to the low
beams
Fog light switch
When in difficult driving conditions,
such as in rain and fog, turn on the
front fog lights to secure front visi-
bility and turn on the rear fog lights
to notify following vehicles the exis-
tence of your vehicle.
Turning on the fog lights

Related Topics

Before driving Driving the vehicle Cargo and luggage Trailer towing (vehicles without towing package) Trailer towing (vehicles with towing package) Driving procedures Power (ignition) switch EV drive mode Transmission Turn signal lever Parking brake Brake Hold Operating the lights and wipers Headlight switch AHS (Adaptive High-beam System) Fog light switch Windshield wipers and washer Rear window wiper and washer Refueling Opening the fuel tank cap Using the driving support systems Lexus Safety System + software update Lexus Safety System + Driver monitor PCS (Pre-Collision System) LTA (Lane Tracing Assist) LCA (Lane Change Assist) LDA (Lane Departure Alert) PDA (Proactive driving assist) FCTA (Front Crossing Traffic Alert) RSA (Road Sign Assist) Dynamic radar cruise control Cruise control Emergency Driving Stop System Speed limiter BSM (Blind Spot Monitor) Rear Vehicle Approaching Indication Automatic Rear Flashing Hazard Lights Secondary Collision Brake (Rear Impacts while Stopped) Safe Exit Assist Lexus parking assist-sensor RCTA (Rear Crossing Traffic Alert) function RCD (Rear Camera Detection) PKSB (Parking Support Brake) Parking Support Brake function (static objects front and rear of the vehicle/static objects around the vehicle) Parking Support Brake function (moving vehicles rear of the vehicle) Parking Support Brake function (pedestrians rear of the vehicle) Lexus Teammate Advanced Park GPF (Gasoline Particulate Filter) system Driving assist systems Driving tips Hybrid Electric Vehicle driving tips Winter driving tips Utility vehicle precautions

Popular Owner Manuals