2024-2026 Lexus LBX SUV Driving -> Operating the lights and wipers User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Driving -> Operating the lights and wipers for Your Lexus LBX SUV First Generation (2024-2026)

211
4
4-3. Operating the lights and wipers
Driving
4-3.Ope rating the lig hts and wipers
Operating the switch turns on
the lights as follows:
1 The front position, tail, license
plate and instrument panel lights
turn on.
2 The headlights and all the
lights listed above turn on.
3 The headlights, daytime run-
ning lights (P.211) and all the
lights listed above turn on and off
automatically.
■ AUTO mode can be used when
The power switch is in ON.
■ Daytime running light function
To make your vehicle more visible to other
drivers during daytime driving, the daytime
running lights turn on automatically when-
ever the hybrid system is started and the
parking brake is released with the headlight
switch in the position. (Illuminate
brighter than the front position lights.) Day-
time running lights are not designed for use
at night.
■ Headlight control sensor
The sensor may not function properly if an
object is placed on the sensor, or anything
that blocks the sensor is affixed to the wind-
shield.
Doing so interferes with the sensor detect-
ing the level of ambient light and may cause
the automatic headlight system to malfunc-
tion.
■ Automatic light off system
● When the light switch is in or :
The headlights and front fog lights (if
equipped) turn off automatically if the
power switch is turned to ACC or OFF.
● When the light switch is in position:
The headlights and all the lights turn off
automatically if the power switch is
turned to ACC or OFF.
To turn the lights on again, turn the power
switch to ON, or turn the light switch to
Headlight switch
The headlights can be operated
manually or automatically.
Turning on the headlights
212
4-3. Operating the lights and wipers
position once and then back to or
.
■ Light reminder buzzer
A buzzer sounds when the power switch is
turned off or turned to ACC and the
driver’s door is opened while the lights are
turned on.
■ Automatic headlight leveling system (if
equipped)
The level of the headlights is automatically
adjusted according to the number of pas-
sengers and the loading condition of the
vehicle to ensure that the headlights do not
interfere with other road users.
■ 12-volt battery-saving function
In order to prevent the 12-volt battery of the
vehicle from discharging, if the light switch
is in the or position when the
power switch is turned off, the 12-volt bat-
tery saving function will operate and auto-
matically turn off all the lights after
approximately 10 minutes.
When the power switch is turned to ON,
the 12-volt battery-saving function will be
disabled.
When any of the following are performed,
the 12-volt battery-saving function is can-
celed once and then reactivated. All the
lights will turn off automatically 10 minutes
after the 12-volt battery- saving function has
been reactivated:
● When the headlight switch is operated
● When a door is opened or closed
■ Welcome light illumination control
The front position lights automatically turn
on at night when the doors are unlocked
using the entry function or wireless remote
control if the light switch is in the posi-
tion.
■ Customization
Settings (e.g. light sensor sensitivity) can be
changed.
(Customizable features: P.556)
1 With the headlights on, push the
lever away from you to turn on the
high beams.
Pull the lever toward you to the center
position to turn the high beams off.
2 Pull the lever toward you and
release it to flash the high beams
once.
You can flash the high beams with the
headlights on or off.
This system allows the headlights and
front position lights to be turned on for
30 seconds when the power switch is
NOTICE
■ To prevent 12-volt battery discharge
Do not leave the lights on longer than
necessary when the hybrid system is not
operating.
Turning on the high beam head-
lights
Extended Headlight Lighting
system
213
4
4-3. Operating the lights and wipers
Driving
OFF.
Pull the lever toward you and release it
with the light switch is in after turn-
ing the power switch off.
Pull the lever toward you and release it
again to turn off the lights.
When any of the following conditions is
met, while the headlights (low beam)
are on, the cornering lights will addi-
tionally turn on and light up the direc-
tion of movement for the vehicle. This is
to ensure excellent visibility when
either driving at intersections or park-
ing at night.
The steering wheel is operated
The turn signal lever is operated
The shift lever is in R (both left and
right side cornering lights)
■ Cornering light control
● The lights illuminate when the vehicle
speed is approximately 30 km/h (19
mph) or less. However, the lights turn off
when the vehicle speed increases to
approximately 35 km/h (22 mph) or
more.
● After the lights remain illuminated for 30
minutes, they automatically turn off.
The level of the headlights can be
adjusted according to the number of
passengers and the loading condition
of the vehicle.
1 Raises the level of the headlights
2 Lowers the level of the headlights
■ Guide to dial settings
2WD models
Cornering lights (if equipped)
Manual headlight leveling dial (if
equipped)
Occupancy and luggage load
conditions
Dial
position
Occupants Luggage load
Driver None 0
Driver and
front passenger
None 0.5
All seats occu-
pied
None 1.5
All seats occu-
pied
Full luggage
loading
2.5
Driver
Full luggage
loading
3.5
214
4-3. Operating the lights and wipers
AWD models
*
: If equipped
According to the vehicle speed, the
brightness and illuminated area of
the high beams are adjusted.
When driving around a curve, the
system uses the high beams to
brightly illuminate the direction of
travel of the vehicle.
The high beams are illuminated so
that the area around a vehicle ahead
is shaded. (Shaded high beam)
The shaded high beam helps ensure for-
ward visibility while reducing the dazzling
effect on the drivers of vehicles ahead.
Occupancy and luggage load
conditions
Dial
position
Occupants Luggage load
Driver None 0
Driver and
front passenger
None 0.5
All seats occu-
pied
None 1.5
All seats occu-
pied
Full luggage
loading
2
Driver
Full luggage
loading
3
AHS (Adaptive High-beam
System)
*
The Adaptive High-beam System
uses a front camera located on the
upper portion of the windshield to
detect the brightness of the lights of
vehicles ahead, streetlights, etc.,
and automatically controls the light
distribution of the headlights.
WARNING
■ For safe use
Do not overly rely on the Adaptive High-
beam System. Always drive safely, taking
care to observe your surroundings and
turning the high beams on or off manu-
ally if necessary.
■ To prevent incorrect operation of the
Adaptive High-beam System
When it is necessary to disable the sys-
tem: P.233
System controls
215
4
4-3. Operating the lights and wipers
Driving
Area illuminated by the high beams
Area illuminated by the low beams
According to the distance to a pre-
ceding vehicle, the illuminated area
of the low beams is adjusted.
1 Press the Adaptive High-beam
System switch.
2 Turn the headlight switch to the
or position.
When the headlight switch lever is in the
low beam position, the AHS will be
enabled and the AHS indicator will illumi-
nate.
■ System operating conditions
● When all of the following conditions are
met, the high beams will illuminate and
the system will operate:
• The vehicle speed is approximately 15
km/h (9 mph) or more
*
.
• The area ahead of the vehicle is dark.
*
: When driving around a curve at a vehicle
speed of approximately 30 km/h or
more, the direction of travel of the vehicle
will be brightly illuminated.
● When all of the following conditions are
met, the headlights will change to the
shaded high beams according to the
position of vehicles ahead:
• The vehicle speed is approximately 15
km/h (9 mph) or more.
• The area ahead of the vehicle is dark.
• There is a vehicle ahead with lights on.
• There are few streetlights or other lights
on the road ahead.
● If any of the following conditions are met,
the system will change to the low beams:
• The vehicle speed is approximately 12
km/h (7.5 mph) or lower.
• The area ahead of the vehicle is not dark.
• There are many vehicles ahead.
• There are many streetlights or other
lights on the road ahead.
■ Front camera detection
● In the following situations, the high beams
may not be automatically changed to the
shaded high beams:
• When a vehicle cuts in front of your vehi-
cle
Using the Adaptive High-beam
System
A
B
216
4-3. Operating the lights and wipers
• When another vehicle crosses in front of
the vehicle
• When vehicles ahead are repeatedly
detected and then hidden due to
repeated curves, road dividers or road-
side trees
• When a vehicle ahead approaches from
a far lane
• When a vehicle ahead is far away
• When a vehicle ahead has no lights
• When the lights of a vehicle ahead are
dim
• When a vehicle ahead is reflecting strong
light, such as the headlights of your vehi-
cle
• Situations in which the sensors may not
operate properly: P.238
● The high beams may change to the
shaded high beams if a vehicle ahead that
is using fog lights without its headlights
turned on is detected.
● House lights, street lights, traffic signals,
and illuminated billboards or signs and
other reflective objects may cause the
high beams to change to the shaded high
beams, cause the high beams not to
change to the shaded high beams, or
change the area that is not illuminated.
● The following may change the speed at
which the shaded areas change or the
timing at which the headlights change to
the low beams:
• The brightness of lights of vehicles ahead
• The movement and direction of vehicles
ahead
• The distance between the vehicle and a
vehicle ahead
• When a vehicle ahead only has lights illu-
minated on one side
• When a vehicle ahead is a two-wheeled
vehicle
• The condition of the road (gradient,
curve, condition of the road surface, etc.)
• The number of passengers and amount of
luggage
● The light distribution control of the head-
lights may not match the driver’s expec-
tations
● Bicycles and other small vehicles may not
be detected.
● In the following situations, the system may
not be able to correctly detect the bright-
ness of the surroundings. This may cause
the low beams to remain on or the high
beams to flash or dazzle pedestrians or
vehicles ahead. In such a case, it is neces-
sary to manually change between the
high beams and low beams.
• When there are lights similar to head-
lights or tail lights in the surrounding area
• When headlights or tail lights of vehicles
ahead are turned off, dirty, changing
color, or not aimed properly
• When the headlights are repeatedly
changing between the high beams and
low beams.
• When use of the high beams is inappro-
priate or when the high beams may be
flashing or dazzling pedestrians or other
drivers.
• When the vehicle is used in an area in
which vehicles travel on the opposite side
of the road of the country for which the
vehicle was designed, for example using
a vehicle designed for right-hand traffic in
a left-hand traffic area, or vice versa
• When it is necessary to disable the sys-
tem: P.233
• Situations in which the sensors may not
operate properly: P.238
■ Customization
Some functions can be customized.
(P.556)
■ Changing to the high beams
Push the lever forward.
The AHS indicator will turn off and the high
beam indicator will turn on.
Pull the lever to its original position to
enable the Adaptive High-beam System
again.
Turning the high beams on/off
manually
217
4
4-3. Operating the lights and wipers
Driving
■ Changing to the low beams
Press the Adaptive High-beam System
switch.
The AHS indicator will turn off.
Press the switch to enable the Adaptive
High-beam System again.
It is recommended to switch to the low
beams when use of the high beams is
inappropriate or when the high beams
may cause problems or distress to
other drivers or pedestrians nearby.
Pull the lever rearward and then return
it to its original position.
The high beams will illuminate while the
lever is pulled, however, after the lever is
returned to its original position, the low
beams will remain on for a certain amount
of time. After this, the Adaptive High-beam
System will operate.
Temporarily switching to the low
beams
218
4-3. Operating the lights and wipers
1 Press the Automatic High Beam
switch.
2 Turn the headlight switch to the
or position.
When the headlight switch lever is in the
low beam position, the AHB system will be
enabled and the AHB indicator will illumi-
nate.
■ Automatic operating conditions of the
high beams
● When all of the following conditions are
met, the high beams will illuminate auto-
matically:
• The vehicle speed is approximately 30
km/h (19 mph) or more.
• The area ahead of the vehicle is dark.
• There are no vehicles ahead with lights
on.
• There are few streetlights or other lights
on the road ahead.
● If any of the following conditions are met,
the headlights will change to the low
beams:
• Vehicle speed drops below approxi-
mately 25 km/h (16 mph).
• The area ahead of the vehicle is not dark.
• There is a vehicle ahead with lights on.
• There are many streetlights or other
lights on the road ahead.
■ Front camera detection
● In the following situations, the high beams
may not be automatically changed to the
low beams:
• When a vehicle cuts in front of your vehi-
cle
• When another vehicle crosses in front of
the vehicle
• When vehicles ahead are repeatedly
AHB (Automatic High
Beam)
The Automatic High Beam uses a
front camera located on the upper
portion of the windshield to detect
the brightness of the lights of vehi-
cles ahead, streetlights, etc., and
automatically changes the head
lights between the high beams and
low beams.
WARNING
■ For safe use
Do not overly rely on the Automatic
High Beam. Always drive safely, taking
care to observe your surroundings and
turning the high beams on or off manu-
ally if necessary.
■ To prevent incorrect operation of the
Automatic High Beam system
When it is necessary to disable the sys-
tem: P.233
Using the Automatic High Beam
system
219
4
4-3. Operating the lights and wipers
Driving
detected and then hidden due to
repeated curves, road dividers or road-
side trees
• When a vehicle ahead approaches from
a far lane
• When a vehicle ahead is far away
• When a vehicle ahead has no lights
• When the lights of a vehicle ahead are
dim
• When a vehicle ahead is reflecting strong
light, such as own headlights
• Situations in which the sensors may not
operate properly: P.238
● The headlights may change to the low
beams if a vehicle ahead that is using fog
lights without its headlights turned on is
detected.
● House lights, street lights, traffic signals,
and illuminated billboards or signs may
cause the high beams to change to the
low beams, or the low beams to remain
on.
● The following may change the timing at
which the headlights change to the low
beams:
• The brightness of lights of vehicles ahead
• The movement and direction of vehicles
ahead
• The distance between the vehicle and a
vehicle ahead
• When a vehicle ahead only has lights illu-
minated on one side
• When a vehicle ahead is a two-wheeled
vehicle
• The condition of the road (gradient,
curve, condition of the road surface, etc.)
• The number of passengers and amount of
luggage
● The headlights may change between the
high beams and low beams unexpect-
edly.
● Bicycles and other small vehicles may not
be detected.
● In the following situations, the system may
not be able to correctly detect the bright-
ness of the surroundings. This may cause
the low beams to remain on or the high
beams to flash or dazzle pedestrians or
vehicles ahead. In such a case, it is neces-
sary to manually change between the
high beams and low beams.
• When there are lights similar to head-
lights or tail lights in the surrounding area
• When headlights or tail lights of vehicles
ahead are turned off, dirty, changing
color, or not aimed properly
• When the headlights are repeatedly
changing between the high beams and
low beams.
• When use of the high beams is inappro-
priate or when the high beams may be
flashing or dazzling pedestrians or other
drivers.
• When the vehicle is used in an area in
which vehicles travel on the opposite side
of the road of the country for which the
vehicle was designed, for example using
a vehicle designed for right-hand traffic in
a left-hand traffic area, or vice versa
• When it is necessary to disable the sys-
tem: P.233
• Situations in which the sensors may not
operate properly: P.238
■ Changing to the high beams
Push the lever forward.
The AHB indicator will turn off and the
high beam indicator will turn on.
Pull the lever to its original position to
enable the Automatic High Beam system
again.
■ Changing to the low beams
Press the Automatic High Beam
Turning the high beams on/off
manually
220
4-3. Operating the lights and wipers
switch.
The AHB indicator will turn off.
Press the switch to enable the Automatic
High Beam system again.
It is recommended to switch to the low
beams when use of the high beams is
inappropriate or when the high beams
may cause problems or distress to
other drivers or pedestrians nearby.
Pull the lever rearward and then return
it to its original position.
The high beams will illuminate while the
lever is pulled, however, after the lever is
returned to its original position, the low
beams will remain on for a certain amount
of time. After this, the Automatic High
Beam system will operate.
Rear fog light switch
1 Turns the rear fog lights off
2 Turns the rear fog lights on
Releasing the switch ring returns it to .
Operating the switch ring again turns the
rear fog lights off.
Temporarily switching to the low
beams
Fog light switch
When in difficult driving conditions,
such as in rain and fog, turn on the
front fog lights to secure front visi-
bility and turn on the rear fog lights
to notify following vehicles the exis-
tence of your vehicle.
Turning on the fog lights
221
4
4-3. Operating the lights and wipers
Driving
Front and rear fog light switch
1 Turns the front and rear fog
lights off
2 Turns the front fog lights on
3 Turns both front and rear fog
lights on
Releasing the switch ring returns it to .
Operating the switch ring again turns only
the rear fog lights off.
■ Fog lights can be used when
Vehicles with rear fog lights only
The headlights are turned on.
Vehicles with front and rear fog lights
Front fog lights: The front position lights are
turned on.
Rear fog lights: The front fog lights are
turned on.
NOTICE
■ To prevent 12-volt battery discharge
Do not leave the lights on longer than
necessary when the hybrid system is off.
222
4-3. Operating the lights and wipers
Operating the lever operates
the wipers or washer as follows:
Intermittent windshield wipers with
interval adjuster
1 Off
2 Intermittent operation
3 Low speed operation
4 High speed operation
5 Temporary operation
Wiper intervals can be adjusted when
intermittent operation is selected.
6 Increases the intermittent wind-
shield wiper frequency
7 Decreases the intermittent wind-
shield wiper frequency
8 Washer/wiper dual opera-
tion
Pulling the lever operates the wipers and
washer.
The wipers will automatically operate a
couple of times after the washer squirts.
Rain-sensing windshield wipers
When AUTO is selected, the wipers
will operate automatically when the
sensor detects falling rain. The system
Windshield wipers and
washer
Operating the lever can change
wiper operation to automatic/man-
ual or squirt washer fluid.
NOTICE
■ When the windshield is dry
Do not use the wipers, as they may dam-
age the windshield.
Operating the wiper lever
223
4
4-3. Operating the lights and wipers
Driving
automatically adjusts wiper timing in
accordance with rain volume and vehi-
cle speed.
1 Off
2 Rain-sensing operation
3 Low speed operation
4 High speed operation
5 Temporary operation
When AUTO is selected, the sensor
sensitivity can be adjusted by turning
the switch ring.
6 Increases the sensitivity
7 Decreases the sensitivity
8 Washer/wiper dual opera-
tion
Pulling the lever operates the wipers and
washer.
The wipers will automatically operate a
couple of times after the washer squirts.
(After operating several times, the wipers
operate once more time after a short delay
to prevent dripping. However, the dripping
prevention does not operate while the
vehicle is moving.)
■ The windshield wipers and washer can
be operated when
The power switch is in ON.
■ Using the voice control system (if
equipped)
The following operations can be performed
using the voice control system:
● Operating the windshield wipers only
once
● Operating the windshield cleaning
washer (it can be performed only when
the vehicle is stopped)
For details regarding the voice control sys-
tem, refer to “MULTIMEDIA OWNER’S
MANUAL”.
■ Effects of vehicle speed on wiper opera-
tion (vehicles with rain-sensing wind-
shield wipers)
Vehicle speed affects the Intermittent wiper
224
4-3. Operating the lights and wipers
interval.
■ Raindrop sensor (vehicles with rain-
sensing windshield wipers)
● The raindrop sensor judges the amount
of raindrops.
An optical sensor is adopted. It may not
operate properly when sunlight from the
rising or setting of the sun intermittently
strikes the windshield, or if bugs, etc. are
present on the windshield.
● If the wiper switch is turned to the
“AUTO” position while the power switch
is in ON, the wipers will operate once to
show that AUTO mode is activated.
● If the temperature of the raindrop sensor
is 90°C (194°F) or higher, or -15°C
(5°F) or lower, automatic operation may
not occur. In this case, operate the wipers
in any mode other than AUTO mode.
■ If no windshield washer fluid sprays
Check that the washer nozzles are not
blocked, if there is washer fluid in the
washer fluid tank.
When the windshield wipers are not
being used, they retract to below the
hood. To enable the windshield wipers
to be lifted when parking in cold condi-
tions or when replacing a windshield
wiper insert, change the rest position of
the windshield wipers to the service
position using the wiper lever.
■ Raising the wipers to the service
position
Within approximately 45 seconds of
turning the power switch off, move the
WARNING
■ Caution regarding the use of wind-
shield wipers in AUTO mode (vehi-
cles with rain-sensing windshield
wipers)
The windshield wipers may operate
unexpectedly if the sensor is touched or
the windshield is subject to vibration in
AUTO mode. Take care that your fin-
gers, etc. do not become caught in the
windshield wipers.
■ Caution regarding the use of washer
fluid
When it is cold, do not use the washer
fluid until the windshield becomes warm.
The fluid may freeze on the windshield
and cause low visibility. This may lead to
an accident, resulting in death or serious
injury.
NOTICE
■ When the washer fluid tank is empty
Do not operate the switch continually as
the washer fluid pump may overheat.
■ When a nozzle becomes blocked
In this case, contact any authorized
Lexus retailer or Lexus authorized
repairer, or any reliable repairer.
Do not try to clear it with a pin or other
object. The nozzle will be damaged.
■ To prevent 12-volt battery discharge
Do not leave the wipers on longer than
necessary when the hybrid system is off.
Changing the windshield wiper
rest position/Lifting the wind-
shield wipers
225
4
4-3. Operating the lights and wipers
Driving
wiper lever to the position and
hold it for approximately 2 seconds or
more.
The wipers will move to the service posi-
tion.
■ Lifting the windshield wipers
While holding the hook portion of
the wiper arm, lift the windshield wiper
from the windshield.
■ Lowering the windshield wipers to the
retracted position
With the windshield wipers placed on the
windshield, turn the power switch to ON
and then move the wiper lever to an operat-
ing position. When the wiper switch is
turned off, the windshield wipers will stop at
the retracted position. Even if the wipers
deviate while the power switch is OFF, the
wipers will return to the normal position.
A
NOTICE
■ When lifting the windshield wipers
● When lifting the wiper arms away from
the windshield pull the driver side
wiper arm upward first, and repeat for
the passenger’s side. When returning
the wipers to their original position, do
so from the passenger’s side first. Oth-
erwise, the wiper arms may be dam-
aged.
● Do not lift a windshield wiper by the
wiper blade. Otherwise, the wiper
blade may be deformed.
● Do not operate the wiper lever when
the windshield wipers are lifted. Oth-
erwise, the windshield wipers may
contact the hood, possibly resulting in
damage to the windshield wipers
and/or hood.
226
4-3. Operating the lights and wipers
Operating the switch operates
the rear wiper as follows:
1 Off
2 Intermittent operation
3 Normal operation
4 Washer/wiper dual opera-
tion
Pushing the lever operates the wiper and
washer.
The wiper will automatically operate a cou-
ple of times after the washer squirts.
The washer will automatically operate and
clean the rear camera.
*
*
: Refer to “MULTIMEDIA OWNER’S
MANUAL”.
■ The rear window wiper and washer can
be operated when
The power switch is in ON.
■ Using the voice control system (if
equipped)
The following operations can be performed
using the voice control system:
● Operating the rear window wiper only
once
● Operating the rear window cleaning
washer (it can be performed only when
the vehicle is stopped)
For details regarding the voice control sys-
tem, refer to “MULTIMEDIA OWNER’S
MANUAL”.
■ If no windshield washer fluid sprays
Check that the washer nozzles are not
blocked, if there is washer fluid in the
washer fluid tank.
Rear window wiper and
washer
The rear window wiper and washer
can be used by operating the lever.
NOTICE
■ When the rear window is dry
Do not use the wiper, as it may damage
the rear window.
Operating the wiper lever
227
4
4-3. Operating the lights and wipers
Driving
■ Reverse-linked rear window wiper
function
When the shift lever is shifted to R when the
front wipers are operating, the rear window
wiper will operate once.
■ Back door opening linked rear window
wiper stop function
When the rear window wiper is operating, if
the back door is opened while the vehicle is
stopped, operation of the rear window
wiper will be stopped to prevent anyone
near the vehicle from being sprayed by
water from the wiper. When the back door
is closed, wiper operation will resume.
■ Customization
Setting of the reverse-linked function can
be changed. (Customizable fea-
tures:P.556)
NOTICE
■ When the washer fluid tank is empty
Do not operate the switch continually as
the washer fluid pump may overheat.
■ When a nozzle becomes blocked
In this case, contact any authorized
Lexus retailer or Lexus authorized
repairer, or any reliable repairer.
Do not try to clear it with a pin or other
object. The nozzle will be damaged.
■ To prevent 12-volt battery discharge
Do not leave the wiper on longer than
necessary when the hybrid system is off.

Related Topics

Before driving Driving the vehicle Cargo and luggage Trailer towing (vehicles without towing package) Trailer towing (vehicles with towing package) Driving procedures Power (ignition) switch EV drive mode Transmission Turn signal lever Parking brake Brake Hold Headlight switch AHS (Adaptive High-beam System) AHB (Automatic High Beam) Fog light switch Windshield wipers and washer Rear window wiper and washer Refueling Opening the fuel tank cap Using the driving support systems Lexus Safety System + software update Lexus Safety System + Driver monitor PCS (Pre-Collision System) LTA (Lane Tracing Assist) LCA (Lane Change Assist) LDA (Lane Departure Alert) PDA (Proactive driving assist) FCTA (Front Crossing Traffic Alert) RSA (Road Sign Assist) Dynamic radar cruise control Cruise control Emergency Driving Stop System Speed limiter BSM (Blind Spot Monitor) Rear Vehicle Approaching Indication Automatic Rear Flashing Hazard Lights Secondary Collision Brake (Rear Impacts while Stopped) Safe Exit Assist Lexus parking assist-sensor RCTA (Rear Crossing Traffic Alert) function RCD (Rear Camera Detection) PKSB (Parking Support Brake) Parking Support Brake function (static objects front and rear of the vehicle/static objects around the vehicle) Parking Support Brake function (moving vehicles rear of the vehicle) Parking Support Brake function (pedestrians rear of the vehicle) Lexus Teammate Advanced Park GPF (Gasoline Particulate Filter) system Driving assist systems Driving tips Hybrid Electric Vehicle driving tips Winter driving tips Utility vehicle precautions

Popular Owner Manuals