2024-2026 Lexus LBX SUV Driving -> AHS (Adaptive High-beam System) User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Driving -> AHS (Adaptive High-beam System) for Your Lexus LBX SUV First Generation (2024-2026)

214
4-3. Operating the lights and wipers
AWD models
*
: If equipped
According to the vehicle speed, the
brightness and illuminated area of
the high beams are adjusted.
When driving around a curve, the
system uses the high beams to
brightly illuminate the direction of
travel of the vehicle.
The high beams are illuminated so
that the area around a vehicle ahead
is shaded. (Shaded high beam)
The shaded high beam helps ensure for-
ward visibility while reducing the dazzling
effect on the drivers of vehicles ahead.
Occupancy and luggage load
conditions
Dial
position
Occupants Luggage load
Driver None 0
Driver and
front passenger
None 0.5
All seats occu-
pied
None 1.5
All seats occu-
pied
Full luggage
loading
2
Driver
Full luggage
loading
3
AHS (Adaptive High-beam
System)
*
The Adaptive High-beam System
uses a front camera located on the
upper portion of the windshield to
detect the brightness of the lights of
vehicles ahead, streetlights, etc.,
and automatically controls the light
distribution of the headlights.
WARNING
■ For safe use
Do not overly rely on the Adaptive High-
beam System. Always drive safely, taking
care to observe your surroundings and
turning the high beams on or off manu-
ally if necessary.
■ To prevent incorrect operation of the
Adaptive High-beam System
When it is necessary to disable the sys-
tem: P.233
System controls
215
4
4-3. Operating the lights and wipers
Driving
Area illuminated by the high beams
Area illuminated by the low beams
According to the distance to a pre-
ceding vehicle, the illuminated area
of the low beams is adjusted.
1 Press the Adaptive High-beam
System switch.
2 Turn the headlight switch to the
or position.
When the headlight switch lever is in the
low beam position, the AHS will be
enabled and the AHS indicator will illumi-
nate.
■ System operating conditions
● When all of the following conditions are
met, the high beams will illuminate and
the system will operate:
• The vehicle speed is approximately 15
km/h (9 mph) or more
*
.
• The area ahead of the vehicle is dark.
*
: When driving around a curve at a vehicle
speed of approximately 30 km/h or
more, the direction of travel of the vehicle
will be brightly illuminated.
● When all of the following conditions are
met, the headlights will change to the
shaded high beams according to the
position of vehicles ahead:
• The vehicle speed is approximately 15
km/h (9 mph) or more.
• The area ahead of the vehicle is dark.
• There is a vehicle ahead with lights on.
• There are few streetlights or other lights
on the road ahead.
● If any of the following conditions are met,
the system will change to the low beams:
• The vehicle speed is approximately 12
km/h (7.5 mph) or lower.
• The area ahead of the vehicle is not dark.
• There are many vehicles ahead.
• There are many streetlights or other
lights on the road ahead.
■ Front camera detection
● In the following situations, the high beams
may not be automatically changed to the
shaded high beams:
• When a vehicle cuts in front of your vehi-
cle
Using the Adaptive High-beam
System
A
B
216
4-3. Operating the lights and wipers
• When another vehicle crosses in front of
the vehicle
• When vehicles ahead are repeatedly
detected and then hidden due to
repeated curves, road dividers or road-
side trees
• When a vehicle ahead approaches from
a far lane
• When a vehicle ahead is far away
• When a vehicle ahead has no lights
• When the lights of a vehicle ahead are
dim
• When a vehicle ahead is reflecting strong
light, such as the headlights of your vehi-
cle
• Situations in which the sensors may not
operate properly: P.238
● The high beams may change to the
shaded high beams if a vehicle ahead that
is using fog lights without its headlights
turned on is detected.
● House lights, street lights, traffic signals,
and illuminated billboards or signs and
other reflective objects may cause the
high beams to change to the shaded high
beams, cause the high beams not to
change to the shaded high beams, or
change the area that is not illuminated.
● The following may change the speed at
which the shaded areas change or the
timing at which the headlights change to
the low beams:
• The brightness of lights of vehicles ahead
• The movement and direction of vehicles
ahead
• The distance between the vehicle and a
vehicle ahead
• When a vehicle ahead only has lights illu-
minated on one side
• When a vehicle ahead is a two-wheeled
vehicle
• The condition of the road (gradient,
curve, condition of the road surface, etc.)
• The number of passengers and amount of
luggage
● The light distribution control of the head-
lights may not match the driver’s expec-
tations
● Bicycles and other small vehicles may not
be detected.
● In the following situations, the system may
not be able to correctly detect the bright-
ness of the surroundings. This may cause
the low beams to remain on or the high
beams to flash or dazzle pedestrians or
vehicles ahead. In such a case, it is neces-
sary to manually change between the
high beams and low beams.
• When there are lights similar to head-
lights or tail lights in the surrounding area
• When headlights or tail lights of vehicles
ahead are turned off, dirty, changing
color, or not aimed properly
• When the headlights are repeatedly
changing between the high beams and
low beams.
• When use of the high beams is inappro-
priate or when the high beams may be
flashing or dazzling pedestrians or other
drivers.
• When the vehicle is used in an area in
which vehicles travel on the opposite side
of the road of the country for which the
vehicle was designed, for example using
a vehicle designed for right-hand traffic in
a left-hand traffic area, or vice versa
• When it is necessary to disable the sys-
tem: P.233
• Situations in which the sensors may not
operate properly: P.238
■ Customization
Some functions can be customized.
(P.556)
■ Changing to the high beams
Push the lever forward.
The AHS indicator will turn off and the high
beam indicator will turn on.
Pull the lever to its original position to
enable the Adaptive High-beam System
again.
Turning the high beams on/off
manually
217
4
4-3. Operating the lights and wipers
Driving
■ Changing to the low beams
Press the Adaptive High-beam System
switch.
The AHS indicator will turn off.
Press the switch to enable the Adaptive
High-beam System again.
It is recommended to switch to the low
beams when use of the high beams is
inappropriate or when the high beams
may cause problems or distress to
other drivers or pedestrians nearby.
Pull the lever rearward and then return
it to its original position.
The high beams will illuminate while the
lever is pulled, however, after the lever is
returned to its original position, the low
beams will remain on for a certain amount
of time. After this, the Adaptive High-beam
System will operate.
Temporarily switching to the low
beams

Related Topics

Before driving Driving the vehicle Cargo and luggage Trailer towing (vehicles without towing package) Trailer towing (vehicles with towing package) Driving procedures Power (ignition) switch EV drive mode Transmission Turn signal lever Parking brake Brake Hold Operating the lights and wipers Headlight switch AHB (Automatic High Beam) Fog light switch Windshield wipers and washer Rear window wiper and washer Refueling Opening the fuel tank cap Using the driving support systems Lexus Safety System + software update Lexus Safety System + Driver monitor PCS (Pre-Collision System) LTA (Lane Tracing Assist) LCA (Lane Change Assist) LDA (Lane Departure Alert) PDA (Proactive driving assist) FCTA (Front Crossing Traffic Alert) RSA (Road Sign Assist) Dynamic radar cruise control Cruise control Emergency Driving Stop System Speed limiter BSM (Blind Spot Monitor) Rear Vehicle Approaching Indication Automatic Rear Flashing Hazard Lights Secondary Collision Brake (Rear Impacts while Stopped) Safe Exit Assist Lexus parking assist-sensor RCTA (Rear Crossing Traffic Alert) function RCD (Rear Camera Detection) PKSB (Parking Support Brake) Parking Support Brake function (static objects front and rear of the vehicle/static objects around the vehicle) Parking Support Brake function (moving vehicles rear of the vehicle) Parking Support Brake function (pedestrians rear of the vehicle) Lexus Teammate Advanced Park GPF (Gasoline Particulate Filter) system Driving assist systems Driving tips Hybrid Electric Vehicle driving tips Winter driving tips Utility vehicle precautions

Popular Owner Manuals