2024-2026 Lexus LBX SUV Driving -> Dynamic radar cruise control User Manual
MyCarUserManual.com
USER MANUALS FOR EVERY MAKE & MODEL

Driving -> Dynamic radar cruise control for Your Lexus LBX SUV First Generation (2024-2026)

278
4-5. Using the driving support systems
Dynamic radar cruise con-
trol
This dynamic radar cruise control
detects the presence of vehicles
ahead, determines the current
vehicle-to-vehicle distance, and
operates to maintain a suitable dis-
tance from the vehicle ahead. The
desired vehicle-to-vehicle dis-
tance can be set by operating the
vehicle-to-vehicle distance switch.
Use the dynamic radar cruise con-
trol only on highways and express-
ways.
WARNING
■ For safe use
● Driving safely is solely the responsibil-
ity of the driver. Do not overly rely on
this system, and pay careful attention
to the surrounding conditions in order
to ensure safe driving.
● The dynamic radar cruise control pro-
vides driving assistance to reduce the
driver’s burden. However, there are
limitations to the assistance provided.
Read the following items carefully. Do
not overly rely on this system and always
drive carefully.
Conditions under which the system may
not operate correctly: P.286
● Set the speed appropriately according
to the speed limit, traffic flow, road
conditions, weather conditions, etc.
The driver is responsible for confirm-
ing the set speed.
● Even if the system is operating cor-
rectly, the condition of a preceding
vehicle as recognized by the driver
and detected by the system may differ.
Therefore, it is necessary for the driver
to pay attention, assess risks, and
ensure safety. Over-reliance on this
system to drive the vehicle safely may
lead to an accident resulting in death
or serious injury.
■ Precautions for the driving assist sys-
tems
Observe the following precautions, as
there are limitations to the assistance
provided by the system. Over-reliance
on this system may lead to an accident
resulting in death or serious injury.
● Details of support provided for the
driver’s vision
The dynamic radar cruise control is only
intended to help the driver in determin-
ing the distance between the driver’s
own vehicle and a designated preceding
vehicle. It is not a system which allows for
careless or inattentive driving, and is not
a system which assists in poor visibility
conditions.
The driver must pay attention to their
surroundings, even when the vehicle
stops.
● Details of support provided for the
driver’s judgement
The dynamic radar cruise control deter-
mines whether the distance between the
driver’s own vehicle and a designated
preceding vehicle is within a set range. It
is not capable of making any other type
of judgement. Therefore, it is absolutely
necessary for the driver to remain vigi-
lant and to determine whether or not
there is a possibility of danger.
● Details of support provided for the
driver’s operation
279
4
4-5. Using the driving support systems
Driving
WARNING
The dynamic radar cruise control does
not include functions which will prevent
or avoid collisions with vehicles ahead of
your vehicle. Therefore, if there is ever
any possibility of danger, the driver must
take immediate and direct control of the
vehicle and act appropriately in order to
ensure safety.
■ Situations in which the dynamic radar
cruise control should not be used
Do not use the dynamic radar cruise
control in the following situations. As the
system will not be able to provide appro-
priate control, using it may lead to an
accident resulting in death or serious
injury.
● Roads where there are pedestrians,
cyclists, etc.
● When driving on a highway or
expressway entrance or exit
● When the approach warning sounds
frequently
● Situations in which the sensors may not
operate properly: P.238
● Situations in which the lane may not be
detected: P.239
280
4-5. Using the driving support systems
Constant speed cruising:
When there are no vehicles ahead
The vehicle drives at the speed set by the driver.
If the set vehicle speed is exceeded while driving down a hill, the set vehicle speed display
will blink and a buzzer will sound.
Deceleration and follow-up cruising
When a preceding vehicle driving slower than the set vehicle speed is detected
When a vehicle is detected driving ahead of your vehicle, the vehicle automatically decel-
erates and if a greater reduction in vehicle speed is necessary, the brakes are applied (the
stop lights will come on at this time). The vehicle is controlled to maintain the vehicle-to-
vehicle distance set by the driver, in accordance with changes in the speed of the preced-
ing vehicle. If vehicle deceleration is not sufficient and the vehicle approaches the vehicle
ahead, the approach warning will sound.
Acceleration
When there are no longer any preceding vehicles driving slower than the set
vehicle speed
The vehicle accelerates until the set vehicle speed is reached and then resumes constant
speed cruising.
Starting off:
Basic functions
A
B
C
D
281
4
4-5. Using the driving support systems
Driving
If a preceding vehicle stops, the vehicle will also stop (controlled stop). After the
preceding vehicle starts off, pressing the “RES” switch or depressing the accelera-
tor pedal will resume follow-up cruising (start off operation). If a start off operation
is not performed, the controlled stop will continue.
Vehicles with LCA: While driving on a highway or expressway, if a preceding vehi-
cle stops, your vehicle will stop accordingly. On some highways and expressways,
if the system determines that the preceding vehicle starts off within approximately
3 minutes of stopping, a buzzer will sound and a message will be displayed on the
multi-information display to notify the driver, and your vehicle will start off accord-
ingly following the preceding vehicle. (Extended resume time)
■ Meter display
Multi-information display
Set vehicle speed
Indicators
■ Switches
Vehicles without a head-up display
Driving assist mode select switch
Driving assist switch
“+” switch/“RES” switch
“-” switch
Cancel switch
Vehicle-to-vehicle distance switch
Vehicles with a head-up display
The function of each switch differs
System components
A
B
C
A
B
C
D
E
F
A
282
4-5. Using the driving support systems
depending on the conditions and
settings.
When a switch is touched, the function of
each switch is displayed on the head-up
display. If the head-up display is off, the
functions will be displayed on the multi-
information display.
Driving assist mode select switch
Driving assist switch
“RES” switch
“+” switch
“-” switch
Vehicle-to-vehicle distance switch
Cancel switch
■ Setting the vehicle speed
1 Press the driving assist mode select
switch to select dynamic radar
cruise control.
The dynamic radar cruise control indicator
will illuminate.
Vehicles without a head-up display
Vehicles with a head-up display
2 Using the accelerator pedal, accel-
erate or decelerate to the desired
vehicle speed (approximately 30
km/h [20 mph] or more), and press
the driving assist switch to set the
set vehicle speed.
The set vehicle speed will be displayed on
the multi-information display.
The vehicle speed at the moment the
switch is released will be the set vehicle
speed.
Vehicles without a head-up display
Using the dynamic radar cruise
control
B
C
D
E
F
G
H
283
4
4-5. Using the driving support systems
Driving
Vehicles with a head-up display
■ Adjusting the set vehicle speed
Adjusting the set vehicle speed
using the switches
To change the set vehicle speed, press
the “+” switch or “-” switch until the
desired speed is displayed.
Vehicles without a head-up display
Vehicles with a head-up display
1 Increase set vehicle speed
2 Decrease set vehicle speed
Short press adjustment: Press the switch
Long press adjustment: Press and hold the
switch until the desired set vehicle speed is
reached.
The set vehicle speed will increase or
decrease as follows:
Short press adjustment: By 1 km/h (0.6
mph) or 1 mph (1.6 km/h) each time the
switch is pressed
Long press adjustment: Increases or
decreases in 5 km/h (3.1 mph) or 5 mph (8
km/h) increments continuously while the
switch is pressed and held
The set vehicle speed adjustment incre-
ment can be changed through a customize
setting.
Increasing the set vehicle speed
using the accelerator pedal
1 Depress the accelerator pedal to
accelerate the vehicle to the
desired vehicle speed.
2 Press the “+” switch.
■ Canceling/resuming control
1 Press the cancel switch or driving
assist switch to cancel control.
Control will also be canceled if the brake
pedal is depressed.
(If the vehicle has been stopped by system
control, depressing the brake pedal will not
cancel control.)
284
4-5. Using the driving support systems
Vehicles without a head-up display
Vehicles with a head-up display
2 Press the “RES” switch to resume
control.
■ Changing the vehicle-to-vehicle
distance
Each time the switch is pressed, the
vehicle-to-vehicle distance setting will
change as follows:
If a preceding vehicle is detected, the
preceding vehicle mark will be dis-
played.
Vehicles without a head-up display
Vehicles with a head-up display
A
Illustra-
tion
Number
Vehicle-
to-vehicle
distance
Approximate Dis-
tance (Vehicle
Speed: 100 km/h
[60 mph])
1 Extra long
Approximately 60
m (200 ft.)
2 Long
Approximately 45
m (145 ft.)
285
4
4-5. Using the driving support systems
Driving
The actual vehicle-to-vehicle distance var-
ies in accordance with the vehicle speed.
Also, when the vehicle is stopped by sys-
tem control, it will be stopped at a certain
distance from the preceding vehicle,
depending on the situation, regardless of
the setting.
■ Operating conditions
● The D shift position is selected.
● The desired set speed can be set when
the vehicle speed is approximately 30
km/h (20 mph) or more.
• If the vehicle speed is set while driving at
below approximately 30 km/h (20 mph),
the set vehicle speed will be approxi-
mately 30 km/h (20 mph).
• If the vehicle speed is set while driving at
a speed that exceeds the system’s upper
limit, the set vehicle speed will be the sys-
tem’s upper limit.
■ Accelerating after setting the vehicle
speed
As with normal driving, acceleration can be
performed by depressing the accelerator
pedal. After accelerating, the vehicle will
return to the set vehicle speed. However,
while in vehicle-to-vehicle distance control
mode, the vehicle speed may decrease to
below the set vehicle speed in order to
maintain the distance from the preceding
vehicle.
■ When the vehicle is stopped by system
control during follow-up cruising
● When the “RES” switch is pressed while
the vehicle is stopped by system control,
if the preceding vehicle starts off within
approximately 3 seconds, follow-up
cruising will resume.
● If the preceding vehicle starts off within
approximately 3 seconds of the vehicle
being stopped by system control, follow-
up cruising will resume.
■ Automatic cancellation of vehicle-to-
vehicle distance control mode
In the following situations, vehicle-to-vehi-
cle distance control mode will be canceled
automatically:
● When the brake control or output
restriction control of a driving support
system operates
(For example: Pre-Collision System,
drive-start control)
● When the parking brake has been oper-
ated
● When the vehicle is stopped by system
control on a steep incline
● When any of the following are detected
while the vehicle is stopped by system
control:
• The driver’s seat belt is unfastened
• The driver’s door is opened
• Approximately 3 minutes have elapsed
since the vehicle was stopped
The parking brake may be actived automat-
ically.
● Situations in which some or all of the
functions of the system cannot operate:
P.239
■ Dynamic radar cruise control system
warning messages and buzzers
For safe use: P.230
■ Preceding vehicles that the sensor may
not detect correctly
In the following situations, depending on the
conditions, if the system cannot provide suf-
ficient deceleration or acceleration is nec-
essary, operate the brake pedal or
accelerator pedal.
As the sensor may not be able to correctly
detect these types of vehicles, the approach
warning (P.286) may not operate.
3 Medium
Approximately 30
m (100 ft.)
4 Short
Approximately 25
m (85 ft.)
Illustra-
tion
Number
Vehicle-
to-vehicle
distance
Approximate Dis-
tance (Vehicle
Speed: 100 km/h
[60 mph])
286
4-5. Using the driving support systems
● When a vehicle cuts in front of your vehi-
cle or changes lanes away from your
vehicle extremely slowly or quickly
● When changing lanes
● When a preceding vehicle is driving at a
low speed
● When a vehicle is stopped in the same
lane as the vehicle
● When a motorcycle is traveling in the
same lane as the vehicle
■ Conditions under which the system may
not operate correctly
In the following situations, operate the
brake pedal (or accelerator pedal, depend-
ing on the situation) as necessary.
As the sensor may not be able to correctly
detect a vehicle, the system may not oper-
ate properly.
● When a preceding vehicle brakes sud-
denly
● When changing lanes at low speeds,
such as in a traffic jam
■ Conditions for extended resume time
(Vehicles with LCA)
Extended resume time is activated when all
of the following conditions are satisfied:
● The connected service that Lexus pro-
vides is subscribed to. Contact any
authorized Lexus retailer or Lexus autho-
rized repairer, or any reliable repairer.
● The vehicle is driving on a vehicle-only
road, such as an expressway.
● There is a preceding vehicle and the sys-
tem is able to detect it.
● No vehicle interruptions occur.
● The preceding vehicle has not been
replaced.
● Clearance sonar and FCTA are not
detecting the object in front of you.
● The driver monitor judges that the driver
is looking forward.
● The steering wheel has not been oper-
ated.
● The brake pedal has not been operated.
In situations where the vehicle
approaches a preceding vehicle and
the system cannot provide sufficient
deceleration, such as if a vehicle cuts in
front of the vehicle, a warning display
will flash and a buzzer will sound to
alert the driver. Depress the brake
pedal to ensure appropriate vehicle-
to-vehicle distance.
■ Warnings may not occur when
In the following situations, the warning
may not operate even though the vehi-
cle-to-vehicle distance is short.
When the preceding vehicle is trav-
eling at the same speed or faster
than your vehicle
When the preceding vehicle is trav-
eling at an extremely low speed
Immediately after the vehicle speed
has been set
When the accelerator pedal is
depressed
When a curve is detected, the vehicle
speed will begin being reduced. When
the curve ends, the vehicle speed
reduction will end.
Depending on the situation, the vehicle
speed will then return to the set vehicle
speed.
In situations where vehicle-to-vehicle dis-
tance control needs to operate, such as
when a preceding vehicle cuts in front of
Approach warning
Curve speed reduction function
287
4
4-5. Using the driving support systems
Driving
your vehicle, the curve speed reduction
function will be canceled.
■ Situations in which the curve speed
reduction function may not operate
In situations such as the following, the curve
speed reduction function may not operate:
● When the vehicle is being driven around
a gentle curve
● When the accelerator pedal is being
depressed
● When the vehicle is being driven around
an extremely short curve
If a detected vehicle in the passing lane
is traveling slower than your vehicle,
overtaking will be suppressed.
The overtaking prevention function will not
operate if the passing lane is congested or
vehicles are traveling at low speeds.
This function is not available for vehicles
without a DCM.
While a warning of the driver monitor
is being displayed, the vehicle acceler-
ation will be restrained.
When the warning of the driver monitor
disappears, the restrained acceleration
control will end.
If your vehicle is being driven at
approximately 80 km/h (50 mph) or
more and a lane change to the passing
lane is performed, when the turn signal
lever is operated and the lane is
changed, the vehicle will accelerate up
to the set speed to assist in overtaking.
For vehicles with a DCM: The system’s
recognition of which lane is the passing
lane is determined by location information
and the driving condition of surrounding
vehicles. The support for lane change func-
tion and overtaking prevention function
may not operate if it is difficult to obtain
location information or there are few sur-
rounding vehicles.
For vehicles without a DCM: The system’s
recognition of which lane is the passing
lane may be based solely on the location of
the steering wheel in the vehicle (left-hand
drive/right-hand drive). If the vehicle is
driven in a location where the passing lane
is on the opposite side of that where the
vehicle was originally sold, the vehicle may
accelerate when the turn signal lever is
operated away from the passing lane. (e.g.
The vehicle was manufactured to be driven
on roads for right-hand drive vehicles [that
overtake on the right], but is being used on
roads for left-hand drive vehicles [that
overtake on the left]. In this case, the vehi-
cle may accelerate when the turn signal
lever is operated to the right.)
If your vehicle is being driven at approxi-
mately 80 km/h (50 mph) or more and
the lane is changed to that with a vehicle
traveling slower than your vehicle, when
the turn signal lever is operated the vehicle
Overtaking prevention function
Driver Monitor support function
Support for lane change
288
4-5. Using the driving support systems
will gradually decelerate to assist in chang-
ing lanes.
When RSA function is enabled and the
dynamic radar cruise control system is
operating, if a speed limit sign is
detected, the detected speed limit will
be displayed with an up/down arrow.
The set speed can be
increased/reduced to the detected
speed limit by pressing and holding the
“+” switch or “-” switch.
■ When the set speed is lower than
the detected speed limit
Vehicles without a head-up display
Vehicles with a head-up display
Press and hold the “+” switch.
■ When the set speed is higher than
the detected speed limit
Vehicles without a head-up display
Vehicles with a head-up display
Press and hold the “-” switch.
■ The dynamic radar cruise control with
road sign assist may not operate prop-
erly when
As the dynamic radar cruise control with
road sign assist may not operate properly in
situations where the RSA may not operate
or cannot detect signs correctly (P.260),
when using this function, make sure to con-
firm the actual speed limit.
In the following situations, the set speed
may not change to the detected speed limit
by pressing and holding the “+” switch or “-”
switch:
● When speed limit information is not avail-
able
● When the detected speed limit is the
same as the set speed
● When the detected speed limit is outside
Dynamic Radar Cruise Control
with Road Sign Assist
289
4
4-5. Using the driving support systems
Driving
of the speed range which the dynamic
radar cruise control system can operate
The settings of Dynamic radar cruise
control can be changed through cus-
tomize settings. (P.564)
The operating state of Dynamic radar cruise control is indicated.
Changing Dynamic radar cruise
control settings
Display and system operation state
Indicator Multi-information display Situation
White
Vehicle-to-vehicle
distance setting: Gray
Dynamic radar cruise
control being OFF
Green
Vehicle-to-vehicle
distance setting: Blue
Set vehicle speed:
Green
Constant speed cruis-
ing
Green
Vehicle-to-vehicle
distance setting: Blue
Set vehicle speed:
Green
Preceding vehicle:
White
Follow-up cruising
290
4-5. Using the driving support systems
Green
Vehicle-to-vehicle
distance setting:
Orange flashing
Set vehicle speed:
Green
Preceding vehicle:
Orange flashing
Approach warning
Green
Vehicle-to-vehicle
distance setting: Gray
Set vehicle speed:
White
Preceding vehicle:
Gray
Accelerating with the
accelerator pedal
Green
Set vehicle speed:
Green in reverse dis-
play
Set vehicle speed
being exceeded
Green
Vehicle-to-vehicle
distance setting: Gray
Set vehicle speed:
White
Preceding vehicle:
Gray
Vehicle in controlled
stop
Indicator Multi-information display Situation

Related Topics

Before driving Driving the vehicle Cargo and luggage Trailer towing (vehicles without towing package) Trailer towing (vehicles with towing package) Driving procedures Power (ignition) switch EV drive mode Transmission Turn signal lever Parking brake Brake Hold Operating the lights and wipers Headlight switch AHS (Adaptive High-beam System) AHB (Automatic High Beam) Fog light switch Windshield wipers and washer Rear window wiper and washer Refueling Opening the fuel tank cap Using the driving support systems Lexus Safety System + software update Lexus Safety System + Driver monitor PCS (Pre-Collision System) LTA (Lane Tracing Assist) LCA (Lane Change Assist) LDA (Lane Departure Alert) PDA (Proactive driving assist) FCTA (Front Crossing Traffic Alert) RSA (Road Sign Assist) Cruise control Emergency Driving Stop System Speed limiter BSM (Blind Spot Monitor) Rear Vehicle Approaching Indication Automatic Rear Flashing Hazard Lights Secondary Collision Brake (Rear Impacts while Stopped) Safe Exit Assist Lexus parking assist-sensor RCTA (Rear Crossing Traffic Alert) function RCD (Rear Camera Detection) PKSB (Parking Support Brake) Parking Support Brake function (static objects front and rear of the vehicle/static objects around the vehicle) Parking Support Brake function (moving vehicles rear of the vehicle) Parking Support Brake function (pedestrians rear of the vehicle) Lexus Teammate Advanced Park GPF (Gasoline Particulate Filter) system Driving assist systems Driving tips Hybrid Electric Vehicle driving tips Winter driving tips Utility vehicle precautions

Popular Owner Manuals